PROVN OF TRG SHED , REPAIR TO SOLAR LIGHTS AND SPL REPAIRS TO BLDG NO P-175/1 and 2 AT MIRC UNDER GE (S) AHMEDNAGAR

Amount

Demolition of cement concrete (unreinforced) in ground floor and pavings n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling stone slabs and tiles of any description or thickness in floors, apros etc laid, bedded and pointed in any mortar all as specified and as directed

Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing ), removing rubbish off the premises all as specified and as directed

Taking down chowhats or frames, area n.exc 1.5 Sqm each (without taking off shutters from frames) all as specified and as directed.

Taking down of chowhats or frame, area exc 1.5 Sqm but n.exc 4.5 Sqm each (without taking off shutters from the frames), all as specified and as directed.

Taking down shutters of any description, area exc 1.0 Sqm but n.exc 2.0 Sqm each all as specified and as directed.

Taking down shutters of any description, area exc 1.0 Sqm but n.exc 2.0 Sqm each and refixing in the same opening including repairing, easing and adjusting all as specified and as directed.

Dismantling boarding of any description or thickness and fixed in any position with nails all as specified and as directed

Taking down cement or cement lime plaster including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified and as directed

Excavation over areas, n exc 1.50m deep and getting out in soft/loose soil all as specified and as directed

Excavation in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, laying of cables etc. or for manholes etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil all as specified and as directed.

Excavation in post holes each n. exc. 0.50Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface all as specified and as directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc 25cm thick all as specified and as directed.

Removing excavated soil to distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and as directed.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and as directed.

M&L for plain cement concrete, 1:2:4, type B-2, using 40 mm graded stone aggregates as in foundations, filling and mass concrete all as specified and as directed.

M&L for RCC 1:2:4, type B1, using 40mm graded stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, and mass concrete all as specified and as directed.

M&L for preast cement concrete block masonry with solid blocks of PCC (1:5:8)( using 20mm graded stone aggregate), exc 10cm in width, built in cement mortar 1:6 complete all as specified and as directed.

S&F 35 mm thick factory made, plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and fixed to chowkat complete all as specified and as directed.

S&F 35mm thick factory made second class hard wood (Kail) glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc ( with out sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete, all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm, made out of 5mm thick plain colour PVC sheet, reinforced with MS square tube, and fixed in opening all as specified and as directed.

S&F factory made molid PVC door shutter, 30mm thick (stiles), consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain olour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panellng of plain colour PVC sheet to be fitted i the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined toghter with solvent cement and fixed to frame complete all as specified and as directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel all as specified and as directed.

S&F continuous (piano) hinges, mild steel bright finish or elctrogalvanised, 40mm width of flap (when opened) all as specified and as directed.

S&F 200mm long, aluminium anodised barrel tower bolts all as specified and as directed.

S&F 150 mm size aluminium handles, cast type, anodised all as specified and as directed.

S&F 140 mm size, floor door stopper of aluminium alloy body and tongue, anodised ,with hard drawn steel spring and fixed in floor all as specified and as directed.

S&F 300mm long, mild steel sliding door bolts, stove enamelled black with bright bolt not less than 12mm dia and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate etc all as specified and as directed.

S&F 25mm dia aluminium power coated curtain rods fixed in pelmets of required lengths complete all as specified and as directed.

M&L for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire & average width of aperature 1.18 mm, fixed with wooden beads / tinned tacks or galvanised wire staples to steel / wooden frame complete all as specified and as directed.

M&L in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire & average width of aperature 1.18 mm, fixed with wooden beads / tinned tacks or galvanised wire staples to steel / wooden frame complete all as specified and as directed.

S&F pressed steel door frame of size 105mm x 60mm x 1.25mm thickness with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc complete all as specified and as directed.

M&L for mild steel TMT bars 6mm to 8mm, cut to length, bent to shape required, including cranking, bending spirally, hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

S&F mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified and as directed.

S&F mild steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded all as specified and as directed.

S&F mild steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or rivetted or forged into spikes, framed guard bars and similar work conforming to Fe 290. Gde-165 complete all as specified and as directed.

S&F rolled mild steel roof trusses (Framed), trussed purlins, crane gantries, rails and fastenings and heavy brackets framing (Tee, beam, angle, channel or flat sections) including distance pieces, cleats, etc and similar work conforming to Fe 290. Gde-165 complete all as specified and as directed.

S&F mild steel plates (plain or chequered) channels, square cut or notched (ordinary or countersunk), forming holes, without any attachment etc. complete conforming to Fe 290. Gde-165 complete all as specified and as directed.

S&F mild steel work in tubular trusses including special shaped washer etccomplete using ERW or induction butt welded tubes conforming to IS - 1161-1979 grade complete all as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based plain steel sheets 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and as directed.

M&L for 19/20mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination fixed with screw including teak wood lipping all around of size 19/20mm x 10mm thick including french polishing to lipping complete as in cupboard shutters (built in) and fixed all as specified and as directed.

M&L for 0.90mm thick decorative laminate type-I of surface finish of approved colour/ pattern and fixed with approved adhesive as per manufacturers instructions all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D2, using 40 mm graded stone aggregates as in sub base all as specified and as directed.

M&L for 40mm thick PCC 1:2:4, type B1, using 20 mm graded stone aggregates as in floor, laid in panels, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for stone sett flooring with stone setts of size 200 to 250mm long, 150 to 200mm wide and 150mm deep and sides dressed and bedded in cement mortar 1:3, 20mm thick; joints grouted in cement mortar 1:2 with an admixture of mettalic hardner 5% weight of cement and struck flush etc complete all as specified and as directed.

M&L for edge stones to flooring with stone setts of size 250 to 300mm long, 150 to 200mm wide and 450mm deep and sides dressed and bedded in cement mortar 1:3, etc complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, as in floors etc. laid over and including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed.

M&L for glazed ceramic tiles (plain or printed), each tile of size exceeding 0.06 Sqm but not exceeding 0.11 sqm, 7 mm thick as on vertical surfaces like dado, skirting etc laid over and including 10 mm thick backing coat in cement mortar 1:4, jointed in neat cement slurry and pointed in coloured cement complete all as specified and as directed.

M&L for 20-25mm thick machine cut kota stone slab flooring laid over and including 20mm thick screed screed bed in cement mortar 1:6, jointed & pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing completecomplete all as specified and as directed.

M&L for 18-20mm thick machine cut kota stone on vertical surfaces such as skirting/ dado over and including 10mm thick backing coat in cement mortar 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishingcomplete all as specified and as directed.

M&L for 20-25mm thick machine cut kota stone slabs (single piece for each step) as in steps of saircase, laid over and including 20mm thick screed bed in cement mortar 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing and rounding nosing of projected tread of each step completecomplete all as specified and as directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like fixed over and including 10mm thick backing coat of cement mortar 1:4 and 25mm thick PCC 1:2:4, type BO, using 12.5 mm graded stone aggregates, pointing in white cement (1:2) using marble dust with admixture of pigment to match with the shade of granite complete all as specified and as directed.

M&L for vitrified ceramic tiles light shade, 10 mm thick (square/rectanglar) polished, area of each tiles n exc 0.36 sqm in floor etc laid over over and including 15 mm thick screed bed in cement mortar in 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles complete all as specified and as directed.

All as per serial item No 56 here-in-before but in dado/skirting etc over and including 10 mm thick backing coat in cement mortar 1:4.

Special treatment to sunken portion with 10mm thick plaster in CM 1:4 with WPC liquid complast 421 and applying one coat each of Nittoproof 100 and Nittoproof 120 on plaster surface. Rendering again 10 mm thick plaster in CM 1:4 mixed with complast 421 in sunken portion of WC and CI pipe joints shall be filled / jointed with mixture of cement, fine sand and Nittoproof 130 and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts light grade 1:3:6 filling, floor area of WC upto 1.5 Sqm etc. complete all as specified and directed. Note : The rate is including for drilling of the hole in RCC @ 1.00 m centre to centre, to a depth to a depth of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and grouting with cement slurry mixed with can bax 100 chemical with pressure grouting with minimum 3 Kg /Sqm all as specified and directed.

M&L for 10mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces, finished even and smooth with thin layer of sagol complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished surfaces even and fair all as specified and as directed.

Complete removal of existing treatment from old decorated plastered or unplastered walls including cornices, pillars etc all as specified and as directed.

M&L for preparation of new or old plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting all as specified and as directed.

M&L for preparation of new or old plastered or unplastered surfaces of walls applying two coats of cement base paint over a coat of primer all as specified and as directed

M&L for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane all as specified and as directed

M&L for 3 mm thick and 38mm wide glass strips, fixed in position to confirm to design all as specified and as directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and as directed.

M&L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and as directed

M&L for preparion of old steel surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and as directed

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, tripple layer, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball including dismantling and taking down existing water tank complete all as specified and as directed.

Dismantling existing water tanks including ball valve from any position/ location of capacity exc 500 ltr but n exc 1000 ltr, setting aside and refixing in the same position all as specified and as directed

S&F in repairs, PVC valveless, syphonic action type, flushing cistern 10 litres capacity low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repairs, wash hand basin vitreous china, white, flat back or angle type of size 550 X 400 mm, including waste, chain and plug and porcelain stopper, waste coupling 32mm dia(CP brass) and waste pipe, a pair of brackets or errecting stand and 15mm bore PVC connection 600mm all as specified and as directed.

S&F in repairs, vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

Taking up or down existing steel tubing and connections, 15mm bore including removal from site complete all as specified and as directed.

S&F 15 mm bore GI tubing, medium grade with all fitting and fixed complete on walls (concealed or open)and ceilings or laid in floors etc complete all as specified and as directed.

Refixing 15 mm bore GI tubing with and including all new fittings and fixed complete in old or new position on walls (concealed or open)and ceilings or laid in floors etc complete all as specified and as directed.

S&F PVC connections, 15 mm bore with PTMT nuts of length 450 mm all as specified and as directed.

S&F in repairs 15mm bore stop cock cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix complete all as specified and as directed.

S&F in repairs 15mm bore brass chromium plated mixer for mixing hot and cold water screwed down for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs bib taps, fancy type, 15 mm bore, cast copper alloy chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repairs 15 mm dia pillar tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and as directed.

S&F in repairs, kitchen plate rack made of stainless steel sheet not less than 0.63 mm thick of over all size 600 mm x 750 mm x 250 mm complete all as specified and as directed. Make : Prayag Cat No P-330 or equivalent in Silver Shine/Suyog/Blue star

S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen including plugs, washers, waste pippe, cast iron cantilever brackets, connecting union to pipe, over all size 915 mmx 460 mm with bowl size 410 mm x 330 mmx 160 mm all as specified and as directed.

S&F in repairs, cast iron floor trap with CP grating including jointing to waste pipe wih cement joint of 75mm dia of outlet including fixing in cement concrete type (1:2:4) type B1 (using 20mm graded stone aggregate) complete all as specified and as directed.

Taking down carefully any type of point wiring (light, fan, bell, socket or power), complete including switches, bell push, ceiling roses, pendants, regulators, sockets, light fittings etc. and making good disturbed surfaces of walls, ceiling, floors etc to match with existing surface complete all as specified and as directed.

Taking down carefully DBs and making good disturbed surfaces of walls to match with existing surface complete all as specified and as directed.

Taking down the existing unserviceable submain wiring of any type including boards from its position and making the good of disturbed surface complete all as specified and as directed.

M & L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards for mounting switches, sockets, fan Regulators, accessories etc as specified and directed for one light point or one fan point controlled by one, one way switch NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.

All as per serial item No. 89 here-in-before but for one 5 Amp, 5 pin socket outlet point on same board with other switches including earth wire as specified.

All as per serial item No. 89 here-in-before but for one 3 pin socket outlet, 5 Amps on independent board.

All as per serial item No. 89 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent.

All as per serial item No. 89 here-in-before but for one light point controlled by two way switches.

All as per serial item No. 89 here-in-before but with 2.5 Sqmm, PVC copper stranded cable FRLS type for phase, neutral and earth for one 15 Amp, 6 pin socket outlet on independent board.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable, drawn through and including PVC rigid conduit not less than 20mm dia with its accessories (ISI marked) and PVC box and fixed with brass screws, cup washer for mounting switches, sockets, fan regulators etc with and including 1.5sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire at other end all as specified and as directed for One light point and one fan point controlled by one, one way swtich all as specified and as directed. NOTE: 1.Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2. All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.

S&F switch piano, flush button, 5 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.

S&F socket outlet, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way suitable for 3 pin/2pin, 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, flush type, 5 pin, 5 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin ) 5/15 Amps, 230V, AC. all as specified & as directed.

S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.

S&F ceiling rose, surface PVC 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.

S&F bell push, flush type, 5 Amp, single pole, 230 volts, white finish all as specified & as directed.

S&F switch piano, flush button, 5 Amp, single pole, 2 way, 230 volts, white finish all as specified & as directed.

S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, 450 watts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.

S&F buzzer/ bell, AC, 230 volts, single phase complete all as specified and as directed.

S&F in repairs, energy saver tube light fitting, 1 x 22 Watt surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories, prewired, including making connections with & including three core copper cable 23/0.0076 from ceiling rose to LED tube light fittings complete all as specified and as directed Make :- Havells cat no LHEXACP71N1S022 or equivalent model of make Philips /Crompton/ Halonix/ Century LED/ Wipro/GE/Luker

S&F in repairs, ultra slim, square profile, LED lighting fixture with extruded polycorbonate, environmental friendly, energy efficient, ready to use pack LED Tube light fitting, 10 Watt with LED light source 6500k with uniform light output, with all accessories including its connection with 2 core seathed copper conductor cable of size 0.5 sqmm all as specified and as directed. Make: HAVELLS E-LITE LED PRIDE PLUS Cat No LHEXBLP71N1009 or equivalent model of make Philips /Crompton/ Halonix/ Century LED/ Wipro/GE/Luker

S&F LED light fitting, 100 Watt, 220 volts, energy saving, environment friendly & robust highbay LED with PDC housing, suitable for ceiling (Surface/Suspended), mounting with system efficacy upto 150 lm/W all as specified and as directed. Make: Havells Cat No : SAUCERGENXPROHBP100WLED757P90DBOLTG or equivalent model of make Philips /Crompton/ Halonix/ Century LED/ Wipro/ GE/ Luker

S&F in repairs, LED Bulb, 10 Watt (Cool day light) having colour temp 6500 K and lumen output 900, suitable for B-22 type to fix on batten holder and wall light etc complete all as specified and as directed. Make : Havells cat No LHLDEUEEML8R010 or equivalent make from Philips /Crompton/ Halonix/ Century LED/ Wipro/GE/Luker

S&F in repairs, security light of building with single piece, new generation energy saving and environmental friendly long life LED, 30 Watt, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of light grade GI Pipe 32 mm dia, 1.5 mtr long, fixed to wall/ pole with two clamps made out of MS flat iron 40 mm x 5 mm and connect to nearest electric supply by two core 1.5 sqmm aluminim cable all as specified and as directed. Make : Havells Cat No LHEXAYP7PN6K030 or equivalent model of make Philips /Crompton/ Halonix/ Century LED/ Wipro/GE/Luker

S&F sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 8 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 200 Amps rated copper busbar, with neutral bar, earthbar and cable lies for cable managment, fully shrouded, neutral bars, prefittes masking sheet complete all as specified and as directed. Make:Havells,Cat No:DHDMSHODDW08 or equivalent approved from list of makes specified in the tender documents.

S&F sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 200 Amps rated copper busbar, with neutral bar, earthbar and cable alley for cable managment, fully shrouded, neutral bars, prefittes masking sheet complete all as specified and as directed. Make:Havells,Cat No:DHDMSHODDW04 or equivalent approved from list of makes specified in the tender documents.

S&F sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), triple pole and neutral, 415 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting, with 100 Amps rated copper busbar, with neutral bar, earthbar and cable alley for cable managment, fully shrouded, neutral bars, prefittes masking sheet complete all as specified and as directed. Make: Havells,Cat No:DHDMTHODDW04 or equivalent approved from list of makes specified in the tender documents.

S&F MCB SP, AC, 240 V, 6 to 32 Amps, 10 KA capacity, 'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed. Make:Havells cat no DHMGBSPF006-32 or equivalent approved from list of makes specified in the tender documents.

S&F in repairs, MCB SP, AC, 240 V, 6 to 32 Amps, 10 KA capacity, 'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed. Make:Havells cat no DHMGBSPF006-32 or equivalent approved from list of makes specified in the tender documents.

S&F MCB SPN, AC, 240 V, 6 to 32 Amps 10 KA capacity, 'c' series making connection with suitable size of copper lugs etc complete all as specified and as directed. Make:Havells cat no DHMGBSNF006-32 or equivalent approved from list of makes specified in the tender documents.

S&F in repairs, MCB SPN, AC, 240 V, 6 to 32 Amps 10 KA capacity, 'c' series making connection with suitable size of copper lugs etc complete all as specified and as directed. Make:Havells cat no DHMGBSNF006-32 or equivalent approved from list of makes specified in the tender documents.

S&F in repairs, ISOLATOR, TPN, AC, 415 V, 63 amps, 10 KA capacity, 'B' series making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB TPN, AC, 240 V, 40 Amps, 10 KA capacity, 'C' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, sheet metal enclosure with plug socket, single pole and neutral, with two pin and earth plug and with one MCB SP of 20 Amps complete all as specified and as directed.

S&F in repairs, exhaust fan, size 300mm sweep, PVC body, AC, single phase, 230/ 240 Volts with louvers including making round hole of size 300mm dia in any type of wall and making good the surface to match the surrounding area complete all as specified and as directed.

Taking out/down and opening of existing ceiling fan, 1200 mm sweep, any make from any position & refixing at the desired location after reassembling and after servicing/overhauling by throughly cleaning the shaft, rotor, stator and applying lubricant/grease to bearings and one coat of super enamelled varnish over winding to improve the insulation resistance including repair/replacement of spare parts/ material/ items, making connection by replacing PVC insulated unsheathed cable of copper conductor of size 1.50 sqmm upto 0.5 mtr length including using material/parts of minor nature such as screws, lugs, insulation tape, nuts, bolts, washers etc after cleaning the metal surface, greasing/lubricant etc to make it functional complete all as specified and as directed. NOTE: The spare parts required, like capcitor, Bearings, Bush, Canopy, down rods etc will be measured and paid separetely under respective items.

S&F in repairs, ball bearing No 6201 all as specified and as directed.

S&F in repairs, ball bearing No 6202 all as specified and as directed.

S&F in repairs, canopy (top and bottom) of ceiling fans any make / size with canopy of matching colour all as specified and as directed..

S&F in repairs, rubber reel with nut, bolts, split pins etc of ceiling fan with rubber reel heavy duty for hanging fan all as specified and as directed..

S&F in repairs, down rod of 15mm bore medium grade GI pipe 0.60 metre long with clamps, bolts, nuts, split pins washers of suitable size of approved quality for ceiling fan all as specified and as directed.

S&F in repairs, connector block of ceiling fan of suitable size of approved quality all as specified and as directed..

S&F in repairs, capacitor of ceiling fans with capacitor having 2.5mfd, 240 Volts all as specified and as directed..

M & L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and as directed. NOTE: 1.Proper colour coding shall adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.Three runs of 2.5 sq.mm cable and one run of PVC casing & caping shall be measured as one unit.

All as per serial item No 130 here-in-before but 2 runs of 4 sqmm cable for phase and neutral and one run of 4 sqmm as continuos earth wire.

All as per serial item No 130 here-in-before but 2 runs of 6 sqmm cable for phase and neutral and one run of 6 sqmm as continuos earth wire.

Supply and laying in trenches or fixing or passing through pipe, 1100 Volts grade, heavy duty LT UG cable of size 16 Sqmm, 2 core with XLPE insulated stranded aluminium conductor served with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall sheathed including cable gland, lugs, jointing material etc and jointing, connecting, testing and commissioning complete all as specified and as directed.

M & L for HDPE pipe (PE 100, SDR 21, 6Kgf/Sqcm IS 4984-2016) 50 mm bore, for laying of LT cables etc complete with all accessories complete all as specified and as directed.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.

M&L in repairs/replacement of earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.

M&L for dismanthing / taking down carefully, the defective SOLAR LED street light, solar panel, charge controller with dusk dawn sensor, lead acid battery of any capacity, junction box and servicing / cleaning, checking connections, replacement of unserviceable spares, re-assembling, refixing at its original location, including reconnections, welding works for battery holding boxes and testing/commissioning complete all as specified and as directed. Note : (i) Spares shall be measured and paid seperately under relevent items of schedule. (ii) Cost of minor parts like screws, nut bolts, washers, dusk dawn sensor, pieces of wires etc required on site are deemed to be included in the quoted rate of this item.

S&F in repairs, battery acid required for top up and repairs of solar street light battery all as specified and as directed.

S&F in repairs, distilled water required for top up and repairs of solar street light battery all as specified and as directed.

S&F in repairs, lead acid battery of capacity 12 Volts, 65 Ah with all parts like screws, nut bolts, etc all as specified and as directed. Make : Exide/ Amaron/ HBL/ Luminous

S&F in repairs, solar photo volatic module, 80 WP (Poly Crystaline type) with 36 number of cell & output voltage of 12 Volts as all as specified and as directed.

S&F in repairs, 12 Volts, 24 Watts, DC LED street Light with Automatic Dusk to Dawn feature directly run on 12 Volts battery & 80 Watts Solar panel with all accessories complete all as specified & as directed.

M/s IBEX Engineers and Contractors

M/s. Sagar Traders

M/S. Z.K.ENTERPRISES, AHMEDNAGAR