SPECIAL REPAIR TO BLDG NO.TN-77 AT 16 COSR, PROVN OF LABORATORY AT 85 FHO, 02 TOILET BLOCK AT EME BN, SMOKE DETECTOR AND FIRE ALARM SYSTEM AND CONSTRUCTION OF KOTE AT CISU UNDER GE NAGROTA.

Amount

Surface excavation not exceeding 30 cm and averaging 15cm deep in any type of soil, complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out any type of soil, complete all as specified and directed.

Returning, filling in including spreading, leveling, watering and well ramming in layers n.exc 25cm complete in any type of soil,complete all as specified and directed by Engineer-in-Charge.

Removing excavated surplus soil to a distance not exceeding 50m and depositing where directed and at a level not exceeding 1.5m above the starting point, complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for hard core of broken bricks boulder n exc 63 mm, deposited, spread and levelled in layers n exe 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Reinforced cement concrete 1:1.5:3 nominal mix, using 20 mm crushed stone aggregate as in slab supported on walls, beams & columns in floors, roofs complete all as specified and directed.

Reinforced cement concrete 1:1.5:3 nominal mix, using 20 mm crushed stone aggregate as in foundation, including rafts, footings, foundatin beams, plinth beams, bases for columns etc. complete all as specified and directed.

Reinforced cement concrete 1:1.5:3 nominal mix, using 20 mm crushed stone aggregate as in beams, cantilevers, lintel over 1.5 m span, bands, chajjas etc. complete all as specified and directed.

Reinforced cement concrete 1:1.5:3 nominal mix, using 20 mm crushed stone aggregate as in columns, complete all as specified and directed.

Use and waste of form work to sides of concrete foundations footings base of columns, plinth beams, raft and raft beams, sides and soffits of foundatin, complete all as specified and directed.

Use and water of form work to soffits of suspended slabs such as roof slabs, not exc 200mm thick, fair finished surfaces of concrete, complete all as specified and directed.

Use and waste of form work to sides of pillars, columns complete all as specified and directed.

Use and waste of form work to edges of concrete flats, treads breaks in floors, window cills, roof etc n.exc. 20 cm wide and sides RCC/PCC bands in wall, horizental or slooring and similar work exc 5 cm but n.exc 15 cm wide, fair finished surfaces of concrete, complete all as specifed and directed.

S&F mild Steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including crancking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90 MM dia or securing with clips quality conforming to Gd I, IS 432(part I) or Fe-410-S or Fe-410-0, complete all as specified and directed.

All as per item No. 15 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and venders.

Mild Steel TMT bars 6 to 8 mm dia , cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 18 here-in-before but except bricks.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, all as specified .

M & L for rendering 15 mm thick on fair faces of brick work in CM 1:4, finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of concrete surfaces in CM 1:3 on ceiling, finishing the surfaces even and smooth without using extra cement, complete all as specified and directed.

M & L for rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement including two coat of white wash on ceiling including preparation of surfaces, complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat primer, complete all as specified and directed.

M & L two coats of oil bound distemper over 2 mm thick wall putty on newly plastered surface of walls including preparation of surfaces complete all as specified and directed.

Preparation of new plaster surfaces and applying three coat of white wash on ceiling, complete all as specified and directed.

M & L for preparing newly plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.

Pressed steel door frame of size 125 mm x 60 mm with one or more rebates using 1.25 mm thick sheet including necessary fixing lugs, lock strike plate including one shop coat of zinc chromate primer, complete all as specified and directed.

S & F 35 mm thick second class hard wood, factory made, plain, framed, panelled shutters (two numbers of panels) with lock rail and panel of 9 mm BWP commercials ply or 12 mm veneered particle board on both faces. The size of rails and size as per IS:1003 (Part-I), Kiln seasoned & chemically pressure treated, complete all as specified and directed.

S & F 35 mm thick second class hard wood, factory made, glazed and skelton shutters, open rebated and prepared to receive glass, gauge, etc. (without sash bars), edges of framing plain, chamered or rounded, fitted with cut and mitred beads for securing glass, etc. Size of memebers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) for doors, complete all as specified and directed.

S&F Box type Steel windows with double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing complete all specified and directed.and shown in drg No. CEUZ/TD/1518/18Sheet No.1/3 to 3/3.

Box type Steel ventilators top hung double shutters (inside for wire mesh & out side for glass), including hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.Steel window shall be conforming to relevant IS, complete all as specified and directed and shown in drg No. CEUZ/TD/1518/18Sheet No.1/3 to 3/3. Note : Wire mesh and sheet glass shall be measured and paid separteley.

S & F Galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm dia and fixed with tinned tacks or galvanised mild steel staples, complete all as specified and directed.

S & F 3.00 mm thick Sheet glass ordinary quality and glazing with oil putty and pin(steel spring for fixing glass) in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

S & F 100 mm long butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed.

S & F 125 mm aluminium handles cast type anodized, complete all as specified and directed.

All as per item No. 37.00 here-in-before but 150 mm.

S & F 250 mm long aluminium alloy, anodized sliding door bolt with hasp stapple ( bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

All as per item No. 39.00 here-in-before but 300 mm long.

S & F 200mm aluminium anodised barrel tower bolt of extruded section and fixed, complete all as specified and directed.

All as per item No.41.00 here-in-before but 150 mm.

M&L for RCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in chajjas/parpet, kitchen shelves and similar items, complete all as specified and directed.

Preparing of new steel surface of any description, and applying two coat of synthetic enamel paint over a coat Zinc red oxide primer not otherwise described over 10 cm width or girth complete all as specified and directed by Engineer in charge.

Prepration of wood or wooden based new or previously untreated surface of any description, over 10 cm width or gridth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for 50 mm thick cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished even and fair all as specified, complete all as specified and as directed.

M & L for 100mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and smooth, complete all as specified and directed.

M & L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as a such base to chequered tile finished even and rough, complete all as specified and directed.

M&L for 50 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as a sub base finished even and smooth, complete all as spd and directed

M&L for 25 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as a sub base to chequered tile finished even and rough, complete all as spd and directed

18mm-20mm thick machine cut kota stone slab flooring (each stone not less than 55 cm X 55cm) over 15 mm thick cement screed base in CM 1:4 laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and applying a coat of cement slurry @ 03 Kg/Sqm of surface, complete all as specified and directed by Engr-in-Charge.

Machine cut kota stone 18-20 mm thick in skirting, dado, riser and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (mirror finish) over and icnluding 15 mm thick rendering in CM (1:4) including tkaing out of existing dado, complete all as specified and directed.

M&L marble work 15 mm thick (550 mm kibg x 75 mm wide strip) as in border in flooring over 20 mm thick acreed in CM 1:4 including pointing in white cement 1:2 using marble dust with mixture of pigments to match with white marble including rubbing grinding and polishing complete all as specified directed.

M&L for cement concrete 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching, padding at roof finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm, complete all as specified and directed.

M&L for APP (atatic polypropline) modified membrane 3mm thick minimum weight not less than 3kg/sqm with 160 gsm/Sqm, non wove polyster mat as center core reinforced laid with 75mm side overlap and 100mm end overlap. The membrane has to be laid with LPG torch and over lap shield and finished neat over roof including a coat of bitumen 85/25 @ 1.2 Kg/Sqm over APP membrane, complete all as specified and directed.

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry and roof over APP membrance laid over 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed.

S&F 100 mm bore PVC (SWR) rain water pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S & F PVC (SWR) bends 100 mm bore fixed to rain water pipe, complete all as specified and directed.

S&F of framed work as in door (as in chowkats) or gates of angle or other section with guest plates rails, braces rail etc exclusive of steel sheeting or other covering hanging also fastening and fixing comforming to Fe-410-0 or Fe-310-0 including shop coat of red oxide including preparation of surface before fixing, complete all as specified and directed.

Mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165, complete all as specified and directed.

20 mm thick screed or screed bedding in cement mortar 1:4 as a sub base to chequered tile & kota stone & flooring, complete all as specified and directed.

Cement concrete interlocking pre-polished tiles machine pressed 30 cm x 30 cm x 25 cm thick, set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors, complete all as specified and directed.

Chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set join ted and pointed in neat slurry in with grey cement and pigments, complete all as specified and directed.

M&L for plain cement concrete, 1:2:4, type B-2 ( using 40 mm graded crushed stone aggregate ) as in foundation/sub base of posts, complete all as specified and as directed.

S & F mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire etc, flat iron fillets for securing for wire mesh/chain link fencing including all necessary welding, drilling, bolting or riveting etc and similar work, complete all as specified and directed.

S & F 4 mm dia galvanised steel wire of mesh size 75 mm x 75 mm made upto into matteress of cages, lapped wired and laid in position including closing after filling including fixing to steel post by welding etc, complete all as specified and directed. Note:-Weight will be worked out through BOO.

M & L for Cement concrete 1:5:10 Type E-2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed.

M&L for preparation of newly surface , undecorated surface and apply two coat of emulsion on walll completed all as specified and directed

S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforcement with square tube complete all as specified and directed

M&L factory made solid panel PVC door shutters 30 mm thick (style) consistiong of frame made out of MS tube of top and bottom rails,. MS frame shall be covered with heat moulded plain coloured PVC channel having a PVC sheet stip of 20 mm width struck inside with solvent cement & stles and plain colour PVC sheet for top rail, lock rail and bottom rail on either sides & as insets for tip rail and bottom rail , paneled of plain colour PVC sheet to be fitted in the MS frame welded/sealed to be stiles and rail with suitable PVC sheet beading and jointed together complete all as specified and directed

Earth filling under floors, spreading, levelling in layers n. exc 25 cm thick each incl watering and well ramming as complete all specified and directed

M & L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) as in sub base to floor finishes, complete all as specified and directed.

M & L Rendering 10 mm thick in cement mortar 1:4 as in backing layer for laying of tiles in vertical surfaces complete all as specified & directed.

M&L for non skid ceramic coloured tiles 400x 400 x 7 to 8 mm thick as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over, complete all as specified and directed.

M & L for Glazed ceramic coloured printed tiles (first quality) of size 350 mm x 250 mm x 7 mm/450 mm x 350 mm x 7 mm thick as in vertical surface, dado/skirting, over , complete all as specified and directed.

M & L for acid resistant tiles 15 mm thick vitreous ceramic, unglazed, set, jointed and pointed in chemical resistant mortar, resin type, in floors over screed bed or bedding layer of CM 1:4, 15 mm thick, complete all as specified and directed.

M & L for glazed ceramic coured tiles of size (300x200x7mm) in vertifical surface set and jointed (joint free) in neat cement slurry and pointed in white cement to match, complete all as specified and directed.

M & L for granite sotne 15 to 18 mm thick for shelves, counter etc (table rubbed and polished) of size not less than 2 m in length, over 20 mm thick screed in CM 1:4 including roughing of existing surface and applying a coat of cement slurry @ 03 Kg/Sqm of surface and pointing with white cement 1:2 using marble dusts admixture of pigment to match, complete all as specified and directed.

S&F steel tubing 15 mm dia (medium grade) with all fitting and fixed to complete to walls and ceilings or laid in floors/roofs complete with all fittings ( such as bend, elbow, tee, short pieces, connecoter, back nuts, union etc) complete all as specified and directed.

All as per item No.80.00 here-in-before but 20 mm bore.

M&L for structural steel for staging of (OHT) framed angle 50 x 50 x6 and FI 50 x 6 bracing including distance pieces, cleats etc Gde Fe-410-s complete all as specified and directed

S & F 1000 Ltrs capacity Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including PVC 20 mm bore float valve, complete all as specified and directed.

All as per item No.83.00 but 500 ltrs capacity.

S&F 20 mm bore ball brass valve fancy.high pressure with polythene float and flynut complete scewed for iron pipe or brass ferrule and fixed in repair complete all as specified.

S&F 20 mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle.screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engr-in-Charge.

S & F 15 mm pillar tap, chromium plated, screwed down high pressure with and without levelled hot or cold with long screwed shanks and fly nuts screwed for pipe and fixed in repairs, complete all as specified and directed.

S & F 15 mm bore bib taps fancy type, chromium plated cast copper alloy with capston head, screwed down , screwed for iron pipe or for brass ferrule and fixed and repair complete all as specified and directed.

S & F CP brass angle valve of size 15 mm screwed down high pressure fancy type screwed both ends for iron pipe 15 mm bore in repairs complete all as specified and directed.

S & F PVC connection 15mm size with PTMT nuts with length 450mm long, complete all as specified and directed.

Sheet glass shelf assemble consistiong of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed

S&F 100 mm dia cast iron soil based and vent pipe an any legth with or without ears with cement joint fixed to walls for sand cast pipes, complete all as specified and directed

S&F 100 mm dia cast iron soil based and vent pipe an any legth with or without ears with cement joint laid in trenches or in floors complete all as specified and directed

S&F 75 mm dia cast iron soil based and vent pipe an any legth with or without ears with cement joint fixed to wall complete all as specified and directed

S&F 75 mm dia cast iron soil based and vent pipe an any legth with or without ears with cemetn joint laid in trenches or in floors complete all as specified and directed

S&F 110 mm bore cast iron bends(any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed

All as per item No.97.00 here-in-before but 100 bore.

S&F 75 mm bore cast iron bends(any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed

S&F 110 mm bore with oval access door cast iron branch pieces single (equal or unequal) ordinary or inverted or with parallel branches complete all as specified and directed

All as per item No.100.00 here-in-before but 100 bore.

All as per item No.100.00 here-in-before but 100 bore and pieces double.

S&F 75 mm bore with oval access door cast iron branch pieces single (equal or unequal) ordinary or inverted or with parallel branches complete all as specified and directed

All as per item No.103.00 here-in-before but 75 bore and pieces double.

S&F 75 mm cast iron vent cowl

S&F 100 mm cast iron vent cowl

S&F 'S' trap of 75 mm bore and fixing properly to WC complete all as specified and directed

S&F Stack clamps out of 100 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends to wall or roof , complete all as specified

S & F in repairs 10 Ltrs capacity PVC valveles, less symphonic action type, flushing cistern low level, white with inlet, ball valve, float and handle 60 mm long flush pipe including brackets, complete all as specified and directed.

S&F vitreous china ware urinal half stall any size including all fitting and fixed to wall complete all as specified and directed

M & L for 62 cm wide Udaypur green stone 15 to 18 mm thick. (table rubbed and polished) as in cooking plateform of size not less than 2 m in length, incl cutting for sink over and including 20 mm thick screed in CM 1:4 including roughing of existing surface and applying a coat of cement slurry @ 03 Kg/Sqm of surface and pointing with white cement 1:2 using marble dusts admixture of pigment to match, complete all as specified and directed.

Vitreous china wash basin, white, flat back, size 550X400 mm including waste pipe, bracket and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug.

All as per item No.112.00 but size 580 x 450 mm.

Vitreous china wash down closet pan (Pedestal pattern) white with white seat cover including PVC (SWR) 'P' trap 110 mm bore including PVC low level cistern of 10 ltr capacity invluding brackets jointing to flush pipe PVC connection (450 x 150 mm) PVC flushing pipe complete all as specified and directed by Engineer-in-charge

S&F in repair Viterous china squatting any type pan Orrisa pattern long pan size 580mm x 440mm white with P or S trap, front and Integral foot rests any pattern excluding flushing cistern and flushing pipe, complete all as specified and directed.

Construction of Septic tank for 10 users , excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab cover in RCC precast manhole cover having 6mm plate embadded all round/fibre reinforced cover with angle iron frame vent shaft as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified and directed.

Construction of Soakage well of size 1.2m dia and 3m depth in excavation in any type of soil foundation in PCC 1:3:6 , walls of honey combed and solid brick work in CM 1:4, RCC M-25 cover slab filling with bats as shown in drg No TD CE/TD-1202/2003 sheet No 1/2 and 2/2 dt 09.10.2003, complete all as specified in drg, complete all as specified and directed. Note : Rate quoted shall deemed inclusive of dwatering during construction if met with.

M&L cement concrete 1:4:8 tpe D-2 using 40 mm graded stone in bed to drain pipe laid in trenches including packing and haunching against the sides of pipe after they are laid and tested for 150 mm dia drain pipe complete all as specified and directed

M&L for 150 mm salt Glazed stoneware drain pipes laid in trenches and jointed complete all as specified and directed

S&F 125 mm shower rose brass chrominium plated complte all as specified and directed

S&F 20 mm dia type D aluminium anodised tubuler towel rail, 60 cm long between flanges complete all as specified and directed

Taking down chowkat with shutter (without taking off shutter from the frame) not exceeding 1.5 sqm each and removing from site (wood or steel), complete all as specified and as directed at site.

All as per item No.122.00 here-in-before but exceeding 1.5 Sqmm and n.exc. 4 Sqmm.

S & F anodized aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, window ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and directed.

S & F anodized aluminium door shutter aluminium section weighting 0.56 kg/m including necessary jointing cleats, glazing clips rubber neoprene packing handles 2 Nos in each door, hinges anodised aluminium snap beading secrews etc complete all as specified and directed as above but powder coated.

S & F anodized window and ventilator shutter side hung type without sash bars, aluminium sections weighting 0.55 kg/m including ncessary jointing cleats, glazing clips rubber packing, aluminium snap beading screws anodised alummnium fittings such as per stay 150 mm long (1 No) hinges type B-2 100 mm long 2 Nos suitable handle 1 Nos, complete all as specified and directed.

S & F 5.5 mm thick sheet glass ordinary quality and glazing with aluminium snap beading in square and fixed to aluminium sectons, complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc, complete all as specified and directed.

M & L for light shade vitrified tile 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or bedding layer in CM 1:4 including distmantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable to store and rubish off the premises, complete all as specifed and directed.

All as per item No.129.00 here-in-before but as in dados.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground levels), complete all as specified and directed.

S & F prepainted galvatume aluminium zinc coating GI based semi corrugated/profile steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction, complete all as specified and directed.

S & F prepainted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof coveing/cladding to wall fixed with self tapping screws/L-type or J-type or cranked hook bolts in lieu of screw as per manufacturer instruction, complete all as specified and directed.

Steel work in tubulor/framed work using chanel, angle or tee as in roof trusses including special shaped washer base plate, gusset plate, MS bolts of 20 mm dia 45 mm long nuts etc complete using ERW or induction but welded tubes confirming to SI-1161-1979 Grade ST-240 complete including purlin, rafter etc with two coat of synthetic enameled paint over a coat of red oxide, complete all as specified and directed.

S & F Mild steel work as in wind ties and similar work , including all necessary drilling, bolting and securing bolts confirming to Fe-410 or Fe- 310 including one coat of red oxide, complete all as specified and directed.

Demolition of brick work / stone masonry built in cement mortar or cement lime mortar including all quoins ,arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles, complete all as specified and directed.

GI T Grid system in 600 x 600 mm module which includes providing and fixing wall angle along the perimeter of the room with nylon sleeves and wooden screws at 300 mm centre to center. Suspendeding the main tee of size from the soffit, soffit cleat, rawl plugs and wire rod & leveling spring clip at 1200mm center to center cross tee, interlockined into the pre-cut slots in the main tees at 600 mm centre to center in direction perpendicular to the main tee to make a grid of 600x 1200mm. Finally 1200 mm cross tees are interlocked in the pre cut slots in the 1200mm tees at 1200 mm center to center in direction parallel to the main tee. Cross Tees having length more than 600 mm are to be supported independently. 6 mm thick aquesostic tile square edge of size 595x595 mm shall be placed into the grid size of 600x600mm. (a) Main T-24x32 thickness 0.3 mm and length 3600. (b) Cross T-24x25 thickness 0.3 mm and length 1200. (c) Cross T-24x25 thickness 0.3 mm and length 1600. (d) Wall angle - 24x24 thickness 0.4 mm and length 3000.

Taking up or down steel water tubing and connection of 15 mm bore, complete all as specified and directed.

Taking up or down steel water tubing and connection of 20 mm bore, complete all as specified and directed.

S & F CP brass shower rose with or without swivel joint 125 mm size including fixing to steel S & F pipe or union complete all as specified and directed.

S & F grating 100 mm size, complete all as specified and directed.

S & F Brass tap 15 mm cost copper alloy with crutch or butterfly handle screwed own screwed for iron pipe, complete all as specified and directed.

S & F factory made solid PVC moulded door shutter 28 to 30 mm thick (styles) with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet of 2 mm on front face and 2 mm plain colour PVC sheet on back face all as specifed and directed with particles board core, complete all as specified and directed.

S & F stainless steel sink made from AISI-304 (18/8) gde steel of 1 mm over all size 688x534 bowl size 610x455x250 mm, complete all as specified and directed. (a) Stainless steel waste coupling. (b) 02 Nos. MS angle iron bracket 45 cm long made out of MS angle iron 35x35x5 mm (c) Waste pipe

Vitreous china wash down water closet pan semi-pedestal pattern (Anglo-Indian type), white (excluding supply of flushing cistern and flush pipes, but including fixing thereof), including making connections to trap, and to flush pipe and fixed in repair, complete all as specified and directed.

75 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F for soap dish, any type, fixed to plugs with chromium plated brass screws, complete all as specified and directed.

M&L 150mm dia slat glazed stoneware drain pipes laid in tenches and jointed, complete all as specified and directed.

Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custedy for taking credit all as specified and as directed by Engr-in-Charge

Taking down ceiling fan any sweep, removing blades ,cleaning the fan completely for dust and dirt and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engr-In-Charge.

Point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;-

One light or one fan point controlled by one switch 5 Amp.

One ceiling fan/exhaust fan point controlled by one switch 5 Amp

One socket outlet 5 amps controlled by one switch on same board

One socket outlet 5 amps controlled by one switch on independent board.

All as per item No.151.00 here in before but point wiring with 2.5 sqmm FR multi stranded copper conductor cable for main circuit and 2.5 sqmm cable as earth continuity conductor for one 15 Amp socket out let controlled by one 15 Amp switch on independat board, complete all as specified and directed.

S & F Switch piano flush type 5 Amps single pole one way, complete all as specified and directed.

S & F Ceiling rose surface bakalite, 3 phase complete PVC/polycarbonate isolated body, complete all as specified and directed.

S & F Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V, 50 Hz, complete all as specified and directed.

LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz, complete all as specified and directed.

S & F batten integrated LED channel of 5W, 230 V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, power factor not less than 0.9, complete all as specified and directed.

S& F LED bulb 7 watt , complete all as specified and directed.

S & F Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete.

S & F socket outlet 2 in 1, 3 pin 5 Amps flush type (Multi purpose).

S & F Switch socket combination 2 in 1 5 pin 5 /15 Amps flush type complete.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc as required, complete all as specified and directed.

S & F LED tube light fitting 18 watt with extruded polycarbonate, inviron mental friendly ISI marked complete all as specified and directed.

Supply only LED lamp 20W.

S&F sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail fitted with copper rated bus bar rated 200 amps, complete all as specified and directed.

S&F Sheet metal enclosure distribution board SPN 4 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail, complete all as specified and directed.

S&F Sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete.

S & F MCB SP and neutral (SPN) 32 amps 230 volts, C series complete all as specified and directed.

S & F MCB SPN 40 Amps 10 KA 230 V olts 'C' series, complete all as specified and directed.

S & F MCB single pole 6 to 32 Amps 10 KA 230 V olts 'C' series, complete all as specified and directed.

S&F MCB DP 63 Amps 10 KA 230 volts "C" series complete.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion, complete all as specified and directed.

Supply & Fix ceiling fans 1200 mm sweep BEE 5 Star rate single phase AC 220 volts 50 Hz aluminium body, copper wound with fan blade aluminium, three core copper wire lead, electronic type regulator (rotary type 360 degree) (ISI marked), complete all as specified and directed.

Supply and fixing Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers for wall mounting including grouting, holding down bolts, nuts, washers and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to exhaust fan including cutting of the hole, complete all as specified and directed.

Supply and laying or fixing cable 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one Mtr apart including 4 mm dia suspension GI wire, complete all as specified and as directed by Engr-in-Charge.

Supply, laying, jointing and testing XLPE insulated PVC sheathed armoured under ground cable heavy duty with aluminium conductor LT 1100 V grade cross sectional area 16 Sqmm 2 core confirming to IS:1554 (Part-I), complete all as specified and directed by Engineer-in-Charge.

Dry sand cushioning to the under ground cable 8 cm before laying the electric cable and 15 cm after laying the cable considering as per SSR 1991 of part-I complete all as specified and directed.

M & L for brick protection using sub class 'B well burnt clay bricks of size 230 mm x 115 mm x 75 mm as a mechenical protection to the power electric cable laid dry flat in the cable rench across the length of the cable, complete all as specified and directed.

S & F 40 mm bore Steel tubing galvanized(Light grade) conforming to IS -1239 for passing cable under road /floor or fixing to poles for protection of underground cable complete with flat iron 50x6 mm clamps made to shape and 12mm dia bolts, nuts and washers for fixing where required, complete all as specified and directed.

S & F 20mm bore brass gun metal gate/globe valves of ISI marked (IS-778 : 1984) with iron wheel head, screwed both ends for iron pipe of high pressure, complete all as specified and directed.

M & L for cutting/welding of existing pipe line of 20 mm dia for taking branch connection for prop pipe complete all as directed by Engr-in-Charge. Note : The cost of necessary earth work shall be measured and paid separately under relevant item of schedule (ii) cost of necessary GI fitting & T & P shall be including in quoted rates.

Supply and fix fire alarm control panel complying with BS EN 54 single loop panel of capa from 99 detectors and 99 modules upto 200 detectors including with 2x12V/ 12 AH battery back to system for continuous operation complete all as specified and directed..

S & F 1.5 Sqmm FRLS stranded copper conductor 2 core with 1.00 Sqmm as each wire, 1100 volt wiring in stove enamelled steel conduit with all fittings for fire alarm system complete all as specified and directed..

S & F detectors complying with and type certified to EN-45 addressable type multisensor detector with heat and smoke combination with all accessories, complete all as specified and directed.

Supply, assembling, erection, testing and commissioning of addressable input/ Monitor module, complete all as specified and directed.

Supply, installation, testing and commissioning of intelligent addressable manual call point esettable type with built in fault isolator for installation inside buildings complete with and including base mounting box, cable glands and installation hardware, complete all as specified and directed.

Supply, installation, testing and commissioning of intelligent addressable fire alarm hooter cum strobe with built in fault isolators for indoor application complete with including base mounting box, cable gland and installations hardwares, complete all as specified and directed.

Supply, fixing and testing of short ckt isolator complete all as specified and directed.

S & F, testing and commissioning response indicator complete all as specified and directed.

Supply, installation, testing and comissioning of the alarm sounder/siren electronic type horizontal single stage continous type normal operation for atleast 50 minutes with sound level 65 db to 120 db measured at 1.5 mtr with sound output variation +5 db, 1000 mtr range, complete all as specified and directed.

Graphic display software with PC for the same be atleast of PIV capacity and specified make only.

Providing and fixing shut of valve mounted signages of zinc sulphite photo luminicent coatin 6 mm thick acrylic sheet with each signages of size 15 x 30 cm and consiting of signages on of side and arrow on other half with each set of signages comprising of the following (Each signages made separatekt if sgeet if suze 15x30 cm) "EXIT" "STAIRCASE" "MANUAL CALL BOX" "HYDRANT" "FIRE ALARM PANEL".

Deduction to be made from BOQ for schedule of credit (Sch 'A' Part - II) Amount of Rs. 25,386.00 during AOC Note:- Tenderers shall not quote for this Schedule

Karmnaya Construction

M/s Khajuria Construction Co.