REPAIR TO ROAD POT HOLES ROAD SHOULDER ROAD BERMS HARDSTANDING ROAD FURNITURE AND CERTAIN CONNECTING WORK AT EASTERN COMPLEX OF MCTE AREA UNDER GE MCTE MHOW

Amount

M&L for preparing surfaces of existing black top surface with wire brushes for removing caked mud etc and sweeping with brooms and finally fanning to clean the surfaces with gunny bags to remove all loose dirt etc and M&L for applying evenly a priming coat/tack coat with hot pressure spray using SS(slow setting) bitumen cationic emultion conforming to IS-8887/ASTMD -2397 @ 7.5 kg/10 Sqm over old bitumious surface allowing it to penetirate atleast 5 to 10mm from top surface of old bitumen and M&L for premixed hot mix Asphaltic Semi Dence (SDAC) Concrete using 5.5% binder content (VG-30 Grade paving bitumen) by weight of total mix and with thickness of 30 mm (consolidated Thickness) including rolling with 8 to 10 tonne power road roller to uniform and smooth surface and consolidation to required gradient and camber all as specified and directed.

Note1 : Cement shall be used as filler at mininum 2% by weight of total mix in event of variation in design mix the percentage of filler content shall be on plus side adopted. (b)SDAC shall be as per MORTH specification Note2: - (i) Laying shall be done by means of self-propelled mechanical paver, finishing with electronic sensor and hydraulic controls with suitable speed and capable of laying, spreading, tamping and finishing. (ii) Mix shall be obtained from computerized hot mix plant and spreading shall be done by using mechanical paver only) (iii) The mix shall be designed by job mix formula and approved by GE. (iv) Cost of testing charges, materials and transportation etc for job mix formula and Independent testing during execution of work shall be inclusive in the unit rate quoted and no extra payment shall be made on this account.

M&L for applying evently a priming coat/tack coat with hot pressure spray using RS(rapid setting) bitumen cationic emultion conformation tp IS-8887/ASTMD-2397 @ 2.5 kg/10 Sqm over bitumious maccadam/ Black top surface all as specified and directed.

M&L for pre mix Dense Bituminius Macadam (DBM) 75mm (Consolidated thickness) lade in single layer using 5.5% minimum binder content by weight of total mix, with paying bitumen of grade VG-30 penetraton using hot mix plant laid by using mechnical sensor paver, rolled and consolidated to required gradient and camber using vibratory/pneumatic and tanderm vibratory roller of capacity exc 8 tone but n.exceeding 12 tone capacity complete all as specified. Note: Marshal stability shall be of minium 900 kg (c) DBM shall be as per MORTH Specification as detailed in particular specition.

M&L for making lines, dashes, arrows, letters etc not exceeding 15 cm wide on bituminous surface with retro reflective thermoplastic road marking paint with reflector sing glass beads @ 250 gms per sqm area confirming to MOST & BIS specification, not less than 2.00 mm thick of white/golden/yellow as approved colour/shade and applied with machine, as per manufacturer's instructon inccluding preparation of surface i.e. cleaning of surface by removing all dust, dirt, oil grease etc complete all as specified and as directed.

Supply and fixing in repair Cat Eye as (Road Stud) of 120mm x 90 mm size made of poly-carbonate moulded body with electronically welded prismatic retro range on both sides for maximum retro reflection in wet and dry condition to be fixed with bituminous ashesive BT-69 any disctiption complete including removal of old cat eye all as specified and directed. (Make - Dark Eye or equivalent of 3M/Alcolite/solar/SUNEYES)

S&F in repair spring posts made of special PU (Poly Urethane) material, which can quickly restore to its original state without damaging the vehicle and itself in case of high speed colllision. Highly reflective heat transfer sheet is pasted on specially designed grooves, make it highly visible from distance at night or in bad weather. The tensile strength and UV stabilizers enables it withstand the harsheet of weather conditions. It is easy to install with an anchor fasters and all as specified and directed.

Demolition of cement concrete ( un-reinforced) of any description and in any position not otherwise specified complete all as directed.

M&L for Moorum/ red bajri filing under foundation or paving laid in layers n exc 15cm thick spread, levelled and rammed including watering all as specified and directed.

M&L for Plain cement concrete 1:2:4 type B-1 using with 20mm graded stone aggregate as in coping edging finish surface even and fair all as specified and directed.

M&L for cement concrete 1:4:8 type D2 using with 40mm graded stone aggregate as in sub base to floors etc as specified and directed.

Dismantling floor, hearth or wall tiling incuding cement mortar bedding (but not backing) removing debrish and rubbish off the premises and stacking serviceable tiles.

M&L for machine presses precast concrete interlocking paver block any size and shape conforming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and direction.

M&L for sand filling under floors or in foundations below interlocking tiles path including watering and consolidation complete all as specified.

M&L providing plecast cement concrete in type B1 1:2:4 (20 mm graded agg) in kerbs and eding to road divder and footpath etc incl necessary earthwork with plain fair faces incl chamfered wheathering throating etc and setting in cement mortar 1:4 complete with joints to match all as specified and directed.

S&F in repair road delineator made of 50mm round MS pipe 80 to 100 cm high above ground level with reflective bends of 3M Hi intensity micro prismatic grade retrorefective sheeting 5 cm red 2 Nos and 10cm yellow 1 No in center with metal jalli for protection, painted black all as specified and directed Note: 1. Excavation removal of surplus soil and size of PCC pit is 200mm x 200mm x 200 mm filled with pcc 1:2:4 type B-1 rate quoted shall be included above.

S&F super delux quality solar stud of Aluminium body including solar-powered by monocrystal solar panel. One high capacity Ni-Cd rechargable battery Approximate 1000 mtrs LEDs-10mm, 3 pieces each side and total 6 pieces are used for high brightness of different colours back up-12 hours of continous lightening at night. (Make - Dark Eye or equivalent of 3M/Alcolite/solar/SUNEYES)

Narayandas Phoolchand Mishra Infrastructures Pvt. Ltd.

Bharadwaj Builders

J B CONSTRUCTION AND DEVLOPERS

KAILASH CHANDRA KHANDELWAL

ram prashad chotelal batham