SPL REPAIR OF 02 X BATHROOM AT BLDG NO P-840 AND P-841 OF 1 SIKH LI AND PROVN OF TOILET BLOCK AT GTO GROUND AT SCN UNDER GE (WEST) JRC

Amount

Demolition of cement concrete in ground floor and paving n.exc 15 cm thick (below or above ground level complete .

Demolition of brick or stone masonary built in cement mortar complete

Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc

M&L brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6.

M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed

M&L Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, hard standing, Manhole, drain etc.

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls.

M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658: 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment.

M & L for 25mm thick Sand filling under floors or in foundations including watering and consolidation

M & L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in kerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work.

M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement.

M&L 15mm thick rendering on wall in CM 1:4 with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface,finished even and smooth without using extra cement.

M&L 15mm thick rendering on wall in CM 1:6 with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface, finished even and smooth without using extra cement.

Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4.

M/L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqM in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter.

M&L Machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L Machine cut kota stone slab flooring 20-25mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L 20mm Granie (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed.

Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc

Demolition of re-inforced cement concrete of any description and in any position not otherwise specifically provided for

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete

M L for Reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) (nominal mix) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432

Demolition of cement concrete above ground floor and paving exc 15 cm thick (below or above ground level complete.

M&L for 15mm thick rendering in 1:3 CM with using with appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface, mixing with Recron 3S micro fibre 6mm @ 125gm per 50 Kag bag of cement, finished even and smooth without using extra cement.Note : Recron 3S micro fibre will be measured and paid in supply only item.

M & L Plain Cement Concrete Type A0 1:1.5:3 (using 12.5 mm graded stone aggregate) mixing with Recron 3S micro fibre @ 900gm per Cum fillet at corners as directed by Engr in Charge complete.Note : Recron 3S micro fibre will be measured and paid in supply only item.

M&L for priming surfaces with bituminous primer polymerised primer oil based @ 0.30kg per Sqm.

M&L for applying coat of industrial bituminous 85/25 @ 1.20 Kg per squqre mtr including cleaning surfaces.

M&L APP based polymeric membrance minimum weight not less than 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) land on primed surface by forced application(Complete surface sealed by gas flame) with over lap of 15 cm complete all as specified and directed complete all as spd and directed.

M & L 25mm thick cement concrete flooring type B-1, 1 :2 : 4, using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement.

M& L Cement concrete type E-2, 1:5:10 using 40mm graded brick aggregate in foundations filling and mass concrete as in sunken floor.

Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall for repairing of existing spout pipe.

M & L for 40mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item)

Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm each

Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm each

Taking down shutters any description exc 1 sqm but n.exc 2sqm each and all as specified and directed

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm

M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick

S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mited and rebated bars any numbers.

S&F 35mm thick flush door shutter, solid core construction with block board core, and plywood face panels, commercial type on both side complete all as sped and directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

Steel window/ventilator 1.25 mm thick Box type ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1, including shop coat primer and following fittings welded to shutters:-i) Hold fasts 150 mm long,12mm x 3mm made to shape -04 No’s, (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 No’s (iii) MS tower bolt 150 mm long per leaf -2 No’s (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete Makes/Manufactures:- M/sTee Pee Enterprises Amritsar, M/S Ram fabricators Pvt Ltd Punchkula.

All as per Ser item No 46 above but glazed shutter.

S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 sqm in each pane complete all as specified.

S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/

S&F Extruded aluminium alloy handles fabricated type anodised 150mm size

S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified.

S & F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm

Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed.

Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls

Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete.

S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I

S&F 1000 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I

S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair

S&F ball float valve brass with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe.

S&Fin repair 15mm dia Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule

S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs.

S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs.

S&F in repair 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated scewed down high pressure with long scrwed shanks and fly nuts screwed for iron pipes

S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets &32mm waste cuppling complete all as specifed and directed.

S&F Vitreous China Water closet (Squatting pattern) "Orissa Pattern" size 580x 440 mm white with 'P' or 'S' trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairs completee

S&F Vitreous China wash down Water closet pan (pedestal pattern) "with plastic water closet seat cover closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging divice (excluding flusing cistern and flush pipe) in repairs complete

S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs

Vitreous China urinals, hallf stall urinals (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed

S&F in replacement CP grating 125mm dia circular of approved make and fixing with cement mortar 1:3 on Nahani Trap or floor trap complete all as specified.

S&F Health faucet heavy,mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified.

S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified

S&F in toilet paper holder of brass chromium plated fixed to walls with brass screws

Supply and fixed Soap dish, any type fixed to walls with plugs with chromium plated brass screws

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed.

S&F brass chromium plated shower rose 125mm size complete all as spd and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc, including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls

S&F110mm PVC (SWR) bends

S&F 75 mm PVC (SWR) bends

S&F110mm PVC (SWR) junction single, (Single T) equal or unequal etc any type of fittings

S&F75mm PVC (SWR) junction single, (Single T) equal or unequal etc any type of fittings

S & F for PVC 110mm (SWR) vent cowl

M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge. (Note : Cost of form work, TMT bars and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed.

M & L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying two coat of synthetic enamelled paint over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M & L for applying white wash of 3 coats as in ceiling incl preparation newly plastered surfaces as specified and directed.

M&L for prepration of old surfaces of ceiling and applying one coat of white (lime) wash on ceiling complete all as specified and directed by Engr -in-charge.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified.

M&L for prepration of old decorated surfaces of walls, washing rubbing down and stooping of distempered and painted surfaces and applying one coat of oil bound distemper complete all as specified and directed by Engr -in-charge.

Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paint over one coat of cement primer complete all as specified.

M&L for prepration of old decorated surfaces of walls and applying one coat of cement base paint complete all as specified and directed by Engr-in-charge.

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc for shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returing, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil.

Removing excavated material n exc 50 m depositing where directed at a level n exc 1.5m above the starting point complete all as spd.

Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed

M &L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed

M&L for concrete bed for 150mm in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to open and rendering, cutting out existing benching for and forming branch channel 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1,smooth finished and reforming benching

Demolition of re-inforced cement concrete of any description and in any position not otherwise specifically provided for

M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks, drain, covers including all form work and setting in CM 1:4 all as specified and shown on drgs.

M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432

Material and labour for cement concrete 1:2:4 Type B-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed by the Engineer-in-Charge.

Surface dressing n exc 15 cm deep getting out in Soft / loose soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil as specified and directed

M&L cement concrete 1:4:8 type D2, using 40m graded aggregate in foundations, filling mass concrete, all as directed

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in old size brick in CM 1:6 as specified and directed

M&L for brick work with sub class 'B' bricks, straight or curved on plan in half brick thick wall, built in cement mortar 1:4 complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. as specified and directed

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point as specified and directed

M & L for 40 mm thick Damp proof course in Cement Concrete 1:2:4 type B 0 in horizontal/vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen @ 1.5 kg/Sqm and blinding with clean dry sand @ 0.05 cum /sqm

M & L for rendering 15 mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L for preparing surfaces plastered or unplasted surface of wall by applying two coat of cement base paint over a coat of primer all as specified and directed

M & L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L for preparation of new plastered or unplastered surfaces of wall and applying three coats of culour wash, complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces finished fair and even without using extra cement.

M&L for three coats of white wash on newly plastered surfaces of ceiling including preparation of wall surfaces complete all as specified and directed

M&L for Mild steel TMT bars 10 mm dia and over cut to length , bent to shape required, including cranking bending and binding with annealed wire not less than 0.9 mm dia complete.

M&L for Mild steel TMT bars 6mm to 8mm dia and over cut to length , bent to shape required, including cranking bending and binding with annealed wire not less than 0.9 mm dia complete.

M&L RCC 1:2:4 using 20 mm graded stone aggregate as Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

S&F formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

M&L RCC 1:2:4 using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L RCC 1:2:4 using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts

Formwork to sides of pillars, posts, struts, piers, columns and stanchions

Material and labour for brocken bricks Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2, using 40mm graded crushed stone aggregate as in plinth protection, surfaces finished even and fair without using extra cement complete all as specified and as directed.

S&F 15mm bore galvanized iron tubes medium grade with all fitting and fixed complete to walls, ceiling or laid in floor complete all as specified.

All as per ser item No 140 above but for 20mm bore tube

S&F Bib tap fancy type cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete all as specified .

S&F Vitreous china wash hand basin (Oval shape) under counter type bowl type including waste coupling and pipe all as specifed and directed.

Supply and fixing pillar tap, fancy type, cast copper alloy chromium plated, with capston heads, 15mm bore dia of pipe screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

Supply and fixing Vitreous china wash down water closet pan (Pedestal pattern incl one toilet paper holder, one health faucet and jet ingrated controlled by two way angle valve) incl plastic water closet seat white colour closed pattern with flat bottom and cover and MS CP aluminium/PVC hinging devices complete all as directed and specified by Engr-in-charge. Make:- CERA/JAQUAR/SOMANY

S&F 10 litres capacity PVC valve less symphonic action type, flushing cistern, low level, white with inlet, ball valve, PVC flush pipe, float and handle including brackets complete all as specified.

Supply and fixing vitreous china bowl urinal, half stall, white complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, etc all as specified and directed.

S&F 15mm stop valves/Angle cock , chromium plated fancy type, screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions

PVC connection fiber, reinforced 45cm long with brass check nut and PVC washers at both ends complete

S&F brass chromium plated towel rail 20 mm dia, 600mm long fixed with chromium plated brass screws wooden/plastic gutties complete all as specified and directed.

S&F soap dish, brass chromium plated, complete all as specified and directed.

M&L Granite 20 mm thick of any type work(table rubbed and polished) in steps, jambs,pillars, windows cill, countertop and like including pointing in white/colour cement and pigment to match with shade of granite including bull nosing of external complete all as specified and as directed.

S&F Rotational moulded plythelene white water storage tank tripple layered white coloured, 1000 litres capacity (cylinderical vertical with cxlosed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density polythene ball screwed for iron pipe (Min for 20mm – 210 gm) complete all as specified and directed.

S&F 20mm Gun metal globe or gate valves, with iron wheel head screwed both ends for iron pipe and fixed complete all as specified.

M&L for non-skid coloured ceramic tiles joint free 7 to 8mm thick square / rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tile, laid over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Glazed ceramic coloured tiles, size 450mm x 350mm x 7mm thick as on vertical surfaces such as dado/skirting etc laid over and including 10mm thick rendering in cement mortar 1:4, set and jointed in neat cement slurry and pointing in white cement with pigment to match complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap with grating including joining to waste pipe fixed in solvent cement incl taking down damaged floor trap in any position complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints jointing with adhesive to wall/laid in trenches complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints jointing with adhesive fixed in repair to wall/laid in trenches complete all as specified and directed.

110 mm bore PVC (SWR) bends in any radius complete all as specified and directed.

PVC (SWR) junction single (single tee) equal or unequal, dia of pipe 75 mm complete all as specified and directed.

S&F chromium plated grating 125mm dia with hole wate, complete all as specified and directed.

S/F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, suppling and fixing in opening as per specification and drawing.

S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

S&F butt hinges, stainlees steel 100mm long (ISI marked), complete all as specified and directed

S&F 150mm long aluminium anodised barrel tower bolt, of extruded section, with bright bolt and fixed complete all as specified.

S&F Aluminum handles, 150 mm size plate type complete all as specified and directed.

S&F Aluminum window and ventilator shutters, sliding type with three track (one track with and including galvanised mild steel wire cloth 0.50 mm nominal dia of wire & average width of aperature 1.00 mm and fixed with tinned tacks or galvanised wire staples, two track with and including 4.8 mm thick glass including solar control film 25 micron reflective type sticked on glass pane as per instructions of manufacturer including necessary fitting and fixture) without sash bars, aluminum sections of size 40x20x1.5 mm fixed in aluminum anodised double frame of section size 63X35X2 mm including necessary jointing cleats, glazing clips, aluminum anodised sap beading, screws, aluminium beading, pvc packing, aluminum anodised fitting and fixture including aluminium chequered grills as on aluminium windows weight not less than 1.0 kg/sqm complete all as specified and directed.

M&L 150mm bore Reinforced concrete pipes, class NP2, laid and jointed complete with collars with cement concrete type D2 1:4:8 (40 mm grade aggregate)as in concrete bed to pipe incl paking under and haunching against sides of pipe after they are laid and tested all as specified.

M& L brick wk in cm 1:4, using sub class 'B' bricks straight of curved on plan exc 6m mean radius, all as directed

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc

M&L for PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) as in cills, PCC blocks, coping, benching, water troughs, seismic and other similar bands, plinth bend, etc including weathering slightly rounded or chamfered angles and throuting , including necessary form work etc all as specified.

M&L for precast cement concrete type B-1 1:2:4 (20mm graded aggregate) and set in Cement Mortar (1:4) as in landings, manholes cover slabs, chajjas, shelves and similar articles including necessary form work all as specified and directed.

Cutting into existing Manholes for connecting new drains , 150mm dia, making good to pipes and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required complete all as specified and as directed by Engr-in-Charge

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors

Taking down unserviceable Submain of any size as directed by Engineer-In-Charge.

Taking down main switch / DB as directed by Engineer-In-Charge.

M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes and plastic laminated white / coloured top sheet cover 3.0 mm thick for: One light / fan / call bell point controlled by one, one way switch.

(a) One 3 pin socket out let 5 Amps on same board with other switches.

(b) One 3 pin socket out let 5 Amps on the independent board.

All as per item No. 179 above but with 2.5 sqmm multistranded copper multistranded conductor FRLS cable with 1.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board

S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, AC

S & F switch Piano 1 5 Amps, flush button type, SP, one way, 230 Volts, AC

S & F socket out let multipurpose 5 pin 5 Amps, flush type, 230 / 250 Volts

S & F socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 / 250 volts , AC with ISI marked

M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified.

Supply and fix DB,double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar.

S/F MCB SPN 32 to 63 Amps 240 volts

S/F MCB SP 6-32 Amps 240 volts

M & L Lamp holder, PVC/Polycarbonate type with back plate incl 01x LED bulb 09 Watt complete suitable for batten fittings.

Supply & fix Exhaust fan made of Sturdy engineering plastic complete with Louvers shutter voltage 230 volts , 50 Hz ,1200 RPM copper winding of sweep 300 mm weep , incl making opening in wall for fixing the exhaust fan with louvers complete all as specified and directed.

S&F in replacement LED tube light fitting 20W (Double side) including LED lamp 20W with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed.

Supply & fixing in replacement LED street light fitting 35 W including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED 6500K and connecting electrical to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed including bracket and fixing clamps etc.

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of 20mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.

M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note : (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

Supply and lay pipe galvanized "medium class" including fitting 15 mm("1/2") dia.

Supply and lay pipe galvanized "medium class" including fitting 20 mm("3/4") dia.

Supply and fix valve ,stop,screwed 20 mm(3/4") dia pipe Stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fix

Supply and fix valve, stop, screwed 15 mm dia pipe Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fix

M&L for drilling and tapping cast iron water mains for branch connection of internal dia

Excavation in trenches in soft/lose soil not exceeding 1.5 Mtr wide and not exc 1.5M depth for shafts wells cesspits manholes piers holes etc laying of pipe of 40mm and getting out all as specified and directed

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25cms thick of soil complete all as specified and directed.

Removing the surplus excavated materisl/soil to a distance not exc 50Mtrs and depositing, where directed at a level not exceeding 1.5 Mtr above the starting point all as specified and directed.

M& L for run lead joint including provision of spun yarm for spigt and socketed ci pipes . fittings of size 100 mm bore complete all as specified

S & F MCB DB SPN 4 way factory made IP-42 protection class metal double door with 200 amps rating busbar 240/430 volt for fixing of MCB /isolator/RCCB etc completed make c&s /Havells/HPL

S/F SP amp rating 240 volts ,10KA 'c' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commisioning Sp 6 to 32 AMP

S/F SPN amp rating 240 volts ,10KA 'c' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commisioning SPN 32 AMP

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size: 10 sqmm 2 core

Excavation in trenches in soft/lose soil not exceeding 1.5 Mtr wide and not exc 1.5M depth for laying of UG cables and getting out all as specified and directed

Returning, filling, including spreading, levelling, watering and well ramming in layers not exc 25cms thick of soil complete all as specified and directed.

M & L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10m all as specified and directed.only punned thickness will be measured.

Removing the surplus excavated materisl/soil to a distance not exc 50Mtrs and depositing, where directed at a level not exceeding 1.5 Mtr above the starting point all as specified and directed.

Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed.

M & L for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed. Note : (i) Earth lead and protection pipe beyond 7.5 m shall be measured and Paid separately. (ii) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor without any extra cost to Govt.

SARASWATI CONSTRUCTION CO (BID ID -3150657)

M/S Kuldip Construction Co. (BID ID -3150585)