Construction of Bridge over river Kalia Nallah on Rusa to Bagudi road in the District of Balasore under SBY for 2025-26.

Earth work in cutting & in road embankment in all kinds of soil with all leads & lift & depositing the excavated materials away from the working area complete as per specification and direction of E.I.C. including cost of all labour required for the work etc., up to bed level etc complete as per the direction of the Engineer in Charge.

Excavation of foundation in soft rock or Soft rock with all lead and lift, shoring, shuttering, proping bullahs, pilling,dewatering etc complete as per the direction of the Engineer in Charge.

Earthwork in excavation in foundation in all kinds of soil within initial lead of 50m. and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Engineer in Charge.

Plain Cement Concrete M-10 using 40mm down graded chips etc.complete as per direction of Engineer-In-Charge.

Plain Cement Concrete M-15 nominal mix (1:2:4) using 20mm down graded chips etc.complete as per direction of Engineer-In-Charge.

In Substructure

In Substructure (HPC)

In Superstructure

Providing ,fitting and fixing ' Z ' Sheet piles including labour for driving with cost , conveyance & taxes etc complete as per direction of Engineer-In-Charge..

RCC of design mix of M-300grade having specified characteristics compressive strength/ target mean strength of 300kg./cm2 in design mix with minimum quantity of cement as specified in IRC Code of 150 mm. cubes at 28 days curing after mixing & tests conducted in accordance with relevant clauses of IS 456/IS 516/IRC 216/1987/IRC-78/1983 using crusher broken hard granite course aggregate of 20mm. down graded sizes & proportion as specified in clause-302.6.2 of IRC 21/1987 & IS-10262 & subject to mix design in conformity with the grading & proportion of different materials for concrete as specified in the relevant codes of approved quality, obtained from approved quarry & using minimum quantity of cement confirming to codal provision including hoisting, lowering & laying concrete in layers not exceeding 15cm thick compacting with vibrators watering & curing for 28 days including water tight steel centering , shuttering & form works finishing the exposed surface smooth providing beads & grooves wherever necessary including cost, conveyance royalties and all other taxes of all materials with all leads & lifts, cost of all labour T&P & machineries etc. required for the work including dewatering if necessary, complete in all respects as per direction of the Engineer-in-Charge but excluding cost, conveyance of tor steel & binding wire & labour charges for straightening, cutting, bending, binding welding & tying the grills lapping spacing etc. where ever necessary & hoisting & placing in position ( to be paid separately as required for RCC works)

Foundation up to Bed

Above Bed

Pier and Abutment Cap

Dirt Wall

Deck Slab

Column and Retaining Wall

Approach Slab

Railing

RCC of design mix of M-250grade having specified characteristics compressive strength/ target mean strength of 300kg./cm2 in design mix with minimum quantity of cement as specified in IRC Code of 150 mm. cubes at 28 days curing after mixing & tests conducted in accordance with relevant clauses of IS 456/IS 516/IRC 216/1987/IRC-78/1983 using crusher broken hard granite course aggregate of 20mm. down graded sizes & proportion as specified in clause-302.6.2 of IRC 21/1987 & IS-10262 & subject to mix design in conformity with the grading & proportion of different materials for concrete as specified in the relevant codes of approved quality, obtained from approved quarry & using minimum quantity of cement confirming to coda

l provision including hoisting, lowering & laying concrete in layers not exceeding 15cm thick compacting with vibrators watering & curing for 28 days including water tight steel centering , shuttering & form works finishing the exposed surface smooth providing beads & grooves wherever necessary including cost, conveyance royalties and all other taxes of all materials with all leads & lifts, cost of all labour T&P & machineries etc. required for the work including dewatering if necessary, complete in all respects as per direction of the Engineer-in-Charge but excluding cost, conveyance of tor steel & binding wire & labour charges for straightening, cutting, bending, binding welding & tying the grills lapping spacing etc. where ever necessary & hoisting & placing in position ( to be paid separately as required for RCC works)

Deck Slab

Hunch

Providing R.C.C of grade M 40 in superstructure, crash barrier & pedestal including cost of all materials, labour, machineries, centering and shuttering, cost of suspended type staging , supported on girders with M.S. bracket arrangment for cantilever portion including cost for all materials and labour for shuttering complete as per approved drawing and technical specification section 1000, 1500, 1600, 1700, 2300 & 2700 of MoRT&H specifications for Road & Bridge works (5th Revision) and as per direction of the Engineer-in-Charge.

Crash Barrier

Providing HYSD bars confirming to approved grade F-415 including all labours for cutting ,bending, binding, lapping, splicing, welding etc. (conforming to ISI specification) & jointing if necessary by lapping & tying the grills & placing in position as required for RCC works as per the approved design, hoisting, lowering & laying position including cost & conveyance of tor steel & binding wires of 18 to 20 gauge(as to be approved by the Deptt.) etc. complete with Cess in all respect (weight of binding wire shall not be considered for payment at all which will be borne by the contractor) as per specification and direction of the Engineer in charge.

Providing and laying 50 mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface etc. complete as per specification & direction of the Engineer in charge.

Providing 600 mm thick Filter media with stone crushed aggregates of 45 mm size satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wingwall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specifications.

Providing Rough stone dry packing / pitching in slope, protection walls, approns and revetments to designed thickness using hard granite stones of required size of approved quality from approved quarry including quarrying supplying conveying and cost conveyance taxes royalty of all materials including complete including filling the interstices with small stones by wedging and hammering finished to proper slope and level as per direction of the Engineer – in – charge including dewatering if required.

Grouting approns and revertments 2.3 cm deep with (1:3:6) with 40 mm down graded size H.G. metal etc. complete as per specification and direction of the Engineer in charge.

Providing C.I. grating to holes in deck slabs size upto 15 cm dia for drainage of water including cost of materials required for the work as directed by the Engineer-in-Charge.

Back filling behind abutment, wing wall & return wall with granular material including all cost, carriage, royality & labour as per specification & direction of the Engineer-in-Charge.

Granular Material

Sandy Material

Providing and laying of compression seal joint consisting of steel armoured nosing at two edges of the joint gap suitably anchored to the deck concrete and a preformed chloroprene elastomer or closed cell foam joint sealer compressed and fixed into the joint gap with special adhesive binder to cater for a horizontal movement upto 40 mm and vertical movement of 3 mm etc. complete as per direction of Engineer-in-charge.

Providing weep holes in the abutment & wing walls 8.00cm. X 23.00cm. size including metal spall backing 30cm X 30cm. size in rear complete as per the approved design & drawing including providing centering & shuttering with cost, conveyance, royality & taxes of all materials T&P articles etc. complete in all respects as per specification & direction of the Engineer-in-Charge.

Providing,fitting and fixing of tar papers including all cost, carriage etc. complete as per derection of Engineer-in-charge.

Providing and applying two coats of enamel paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm etc. complete as per derection of Engineer-in-charge.

Providing and applying two coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm etc complete asper direction of Engineer in Charge.

Providing and Fixing Informatory Sign Board & Citizen Information board with logo as per design including cost of all materials and labour etc complete asper direction of Engineer in Charge.

Clearing and grubbing road land including rank vegitation, grass, bushes, shrubs, sapplings and trees girth upto 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness etc. all complete as per direction of the Engineer-in-charge.

Construction of embankment with approved material obtained from borrow pits with 5 extra lead lifts and leads, transporting to site by mechanical means within a lead of 5kms, spreading, grading to required slope and compacting to meet requirement of table 300-2 & clause 305 of MoSRT&H Specifications for Road & Bridge works (4th Revision)and as per the direction of engineer in charge.

Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision)

Providing, laying, spreading & compacting graded stone aggregate to Wet Mix Macadam specification including pre mixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base/base course on well prepared surface & compacting with vibratory roller to acieve the desired density as per clause 406 of MoSRT & H specifications for road & bridge works.(4th Revision)

Wearing coat

Providing and applting Primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surfaces and spraying primer @ 0.60kg/ sqm using Mechanical means as per clause 502 of MoSRT&H Specifications of Road & Bridge work (04th Revision)

Providing and applying Tack coat with bitumen emulsion on prepared surface including clearing of road surfaces and spraying primer @ 0.20kg/ sqm using Mechanical means as per clause 502 of MoSRT&H Specifications of Road & Bridge work (04th Revision)

Providing & laying Bituminous Macadam with hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transported to site, laid over previously prepared surface with hydrostatic paver finisher with sensore control to the required grade, level & alingment & roling with smooth wheeled,vibratory & tandem rollers to achieve the desire compaction as per clause 504 of MoSRT&H Specifications for road and bridge works.

Providing and laying sub-base (With Sand-Moorum) in shoulders in layers not exceeding 100mm watering and compaction to the required density in O.M.C. with PRR including cost and conveyance, royality and taxes of sub-base materials etc. complete as per direction of the Engineer-in-charge.

Construction of un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M-30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction, expansion and construction joints, applying sealant, admixtures as approved, curing of concrete slabs for 14-days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification as per direction of the Engineer-in-Charge.

Providing laying R.C.C. Hume pipe NP3 class for culverts including fixing collar with cement mortar 1:2 but excluding excavation, protection work, backfilling,concrete and masonry work in head walls and parapets clause 1106 of MORD specification for Rural roads and as per irection of Engineer-in charge.

1000 mm dia Single row

Supplying, Transporting and fixing Reinforced cement concrete (1:2:4) Circular Guard Posts (Size 0.15m dia at bottom & 0.10 M dia at Top of 1.20 m long) of standard design fixed in position including finishing and painting etc all complete as per direction of the Engineer-in-charge.