REPAIRS TO JOINERIES AC/CGI ROOF FASCIA BOARD FALSE CEILING AND CERTAIN MISC WORKS AT AF STN PURNEA

Amount

Dismantling of old plain or corrugated steel sheeting or pre painted galvalume sheeting any gauge, thickness, including nainital or similar pattern of roof covering and segregating serviceable sheet, keeping them staked for reuse and unserviceable sheet removed from site of work complete all as specified and as directed.

Dismantling of old asbestos cement (Corrugated/ semi corrugated etc) sheet in roof covering fixed in any position with L hooks/J hooks/nails including capping to ridges and hips and remove materials from site of work complete all as specified and as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and as directed.

S & F 6mm thick corrugated or semi-corrugated asbestos cement sheets in roofs, walls etc with L- type or J- type or cranked hook bolts complete all as specified and as directed.

S & F 6mm thick corrugated or semi-corrugated asbestos cement sheets in ridge etc with L- type or J- type or cranked hook bolts complete all as specified & as diretced.

Dismantling wrought iron or mild steel works of any description not otherwise provided for and remove materials from site of work,complete all as specified and as directed.

S & F mild steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, fordoors, balusters, nosing to steps including embeding in concreteand screwing etc. wind ties for roof including securing bolts joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of Fe-290, (Gde E-165) complete all as specified and as directed.

All as per item No 8 here-in-before but except material, complete all as specified and as directed. Note:- Old serviceable materials obtained from Ser Item No 7 here-in-before

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surface exc 10 cm width or girth ,not other wise described including preparation of steel surfaces complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on old steel surface exc 10 cm width or girth ,not other wise described including preparation of steel surfaces complete all as specified and as directed.

Dismanting wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed.

S&F 4mm thick asbestos cement plain building board non combustible material as per IS-14862 fixed in ceiling, flat or sloping to timber frame work with screws complete all as specified and as directed.

All as per item No 8 here-in-before but except material, complete all as specified and as directed. Note:- Old serviceable materials obtained from Ser Item No 12 here-in-before

M&L for preparation surfaces of new ceiling surface and applying two coats of white wash complete all as specified and as directed.

M&L preparation of old ceiling surface of wall and applying one coats of white wash complete all as specified and as directed.

Taking down cement plaster on walls, including raking out joints, hacking for key, scrubbing down with water etc. and remove rubbish from site of work complete all as specified and as directed.

M&L 15mm thick rendering on fair faces of brick work in cement mortar 1:6 surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new wall surfaces and applying two coats of OBD over a coat of primer complete all as specified and as directed.

M&L for preparation of old wall surfaces including removal of all existing treatement, washing rubbing down and applying two coats of OBD over a coat of primer complete all as specified & as diretced.

Hacking out old broken glass (any thickness ,size quality or description ) from metal frame including punching drilling out old glazing pin /spring clip and providing and fixing complete all as specified and as directed.

S&F for 4.0 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm each pane complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified & as diretced.

M&L for preparation of old wooden surfaces including removal of all existing treatement of any description over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified & as diretced.

Demolition of old cement concrete in ground floor and paving n exc 15 cm thick below or above ground floor and remove rubbish from site of work complete all as specified and as directed.

M&L for 50mm thick PCC 1:3:6 type C1 using 20mm graded stone aggigate and finished the concrete surface even and smooth without using extra cement as in plinth protection complete all as specified and as directed.

Taking down Chowkhats or frames with shutters (wihout taking off shutters) from the frame exc 1.5 sq. m but n exc 4 sq. m complete all as specified and as directed

Taking down shutter of any description exc 1 Sqm and n.exc 2 sqm each complete all as specified and as directed

Taking down shutter of any description n exc 1 Sqm each complete all as specified and as directed

S&F factory made solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, fixing in opening as per specification and all as per drawing, complete all as specifed and as directed

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S&F 35mm thick of 2nd class HW in Plain, framed, panelled shutters chowkat (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers complete all as specified and as directed.

S&F 35mm thick of 2nd class HW glazed and skeleton shutters in chowkats, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied complete all as specified and as directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 150mm size and aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F 250mm size aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed.

S&F 100mm size butt hinges, heavy weight, cold rolled mild steel to wooden or steel frame including necessary screw/bolt/welding complete all as specified and as directed.

S&F 125mm size aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 100mm size and aluminium anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood thrusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed. NOTE:- The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quoted amount.

M/S. KESHAB CHANDRA GHOSH

M/S. Suryabanshi Construction