ADDN/ALTN TO 150 ORS MD ACCN (PH-III) AT MCEME UNDER GE MCEME SECUNDERABAD

Amount

Demolition of cement concrete un reinforced of any description and in any position and debrises off the premises complete all as specified and directed..

Material and labour for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded stone aggregate as in padding concrete (levelling course) on roof complete all as specified and as directed.

Material and labour for rendering 10 mm thick in CM (1:3) using water proofing compound as per manufacturer instructions as in roof padding and chajjas complete all as specified and as directed . Note : Water proofing compound will be measured and paid separately.

Material and labour for APP modified prefabricated five layer water proofing membrane minimum 3mm thick and weighing not less than 3.6 kg/Sqm, reinforced with non woven polystester matt black finished (wt not less than 150 gms/Sqm) over combatible primer at 0.40 Ltr/Sqm and torch applications of membrane with minimum 10cm side over lap and 15cm end laps and applying solar reflective bituminous aluminium paint @ 0.10 kg / sqm complete all as specified and as directed.

Supply only liquid integral water proofing compound complete all as specified and directed

Material and labour for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc completed all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing srviceable tiles to store and rubbish off the premises complete all as apecified and as directed.

Material and labour Anti-skid / Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed

Material and labour Anti-skid / Non skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed

Material and labour for 15 mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for laying floor finishes all as specified and as directed .

Material and labour glazed ceramic coloured tiles 450x 300x 6 to 7mm thick on vertical surfaces such as dados, wall etc set and jointed in neat cement slurry and pointed in white or coloured cement to match on vertical surfaces all as specified and as directed .

Material and labour for rendering 10 mm thick in CM (1:4) finished rought to receive wall tiles all as specified and as directed .

Material and labour for 18-20mm thick Granite (of any type) tiles machine cut, bedded and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and rounding edges, over 15 mm thick screed bed or bedding layer of mortar in cement mortar 1:6 for lying floor finishes complete all as directed and polishing complete all as specified and as directed .

Demolition of brick work or stone masonry built in cement mortar including pillar etc. complete all as specified and as directed .

Material and labour for brickwork with fly ash modular bricks straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and as directed .

Material and labour Brick work with Fly ash modular bricks straight or curved on plan to any radius in half brick thick walls built in cm 1:4 complete all as specified and as directed .

Taking down plastering in cement mortar on brick or stone wall/ ceilings etc including racking out joints hacking for key scrubbing down with water etc. including cleaning away the debrises complete all as specified and as directed .

Material and labour for rendering 10mm thick cement plaster 1:6, incl finishing even and smooth without using with out extra cement on internal surfaces all as specified and as directed .

Material and labour for rendering 15 mm thick in two coats, 10 mm thick in cement plaster 1:6 and 5 mm thick in cement plaster 1:4 mixed with integral water proofing compound as per manufacturers instructions, on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and as directed. Note :Water proofing compound shall be measured and paid seperately

Material and labour for cement plaster 1:3, 5 mm thick incl finishing even and smooth without using extra cement on ceiling all as specified and as directed.

Material and labour for rendering 10mm thick on fair faces of brick work, chajja, facia,slabs etc in CM 1:3 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for applying two coats of OBD over two coat of wall care putty over a coat of alkali resistant primer including preparing the new plastered wall surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment on walls and applying two coats of oil bound distemper over two coat of wall care putty over a coat of alkali resisitant primer complete all as specified and directed.

Material and labour for three coats of white wash to ceiling surfaces including preparation of new surfaces complete all as specified and as directed.

Material and labour for preparation of old surface of ceilings and applying one coat of white wash complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C2 using 40 mm graded aggregate as in plinth protection/ Paths of 75mm thick. Finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for removing loose and broken concrete by chiselling /picking etc upto a depth of 10 to 20 mm from floor/roof slab/chajjas and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not exceeding 50m, complete all as specified and as directed.

Material and labour for application of high build polymer modified cement mortar (1:2.5) mixed with 3 kg SBR per bag of cement in ceiling surfaces 10 to 20mm thick in two layers surfaces over a coat of bonding agent Nito Bond SBR (1 Ltr SBR + 1 Ltr) water + 3 kg cement), complete all as specified and as directed .

Demolition of RCC in fins, fascia column edges including cutting reinforcement etc, complete all as specified and as directed.

Material and labour for Form work to flat surfaces of RCC fins, fascia ,chjjas and similar items including edges, for rough finished surfaces complete all as specified and as directed.

Material and labour for RCC 1:2:4 type B1 (Using 20 mm graded stone aggregate) chajjas complete all as specified and as directed.

Material and labour Formwork to ,rough finished surfaces of flat concrete,soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping),etc complete all as specified and as directed.

Material and labour PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) as in coping including form work complete all as specifed and directed.

Material and labour for RCC 1:2:4 type B1 (Using 20 mm graded stone aggregate) Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for precast cement concrete 1:2:4, type B1 (using 20 mm graded stone aggregate), as in man holes cover slabs etc including necessary form work and set in CM 1:6, complete all as specified and as directed. Note:- Reinforcement will be measured and paid seperately

Material and labour for Mild steel TMT bars 10mm dia and over , cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed.

Material and labour for welding in repairs exc 2.5cm and n. exc 5cm in length, thickness of Metal to be welded n.exc 6mm , on steel windows / ventilators and steel door shutters of any description all as specified and as directed.

Taking down chowkats with shutters (without taking off shutter from the frames ) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames ) exceeding 1.5 Sqm each but n.exc. 4 sqm each complete all as specified and as directed.

Taking down, Shutters of any description exc 1 but n exc 2 sq. m each, etc completeall as specified and as directed.

Taking down Shutters and Resecuring or easing & adjusting, and fixing in the same opening of any description exc 1 sq. m and n exc 2 sq. m each

Material and labour for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M S Square tube, supplying and fixing in opening as per manufacturers instructions all as directed complete all as specified and as directed.

Material and labour for Factory made solid panel laminated PVC door shutter 30mm thick (style) consisting of frame made out M.S tube for top & bottom rails. M.S Frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail : Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/scaled the stiles & rails with suitalble PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site all as specified and as directed.

Supply and fix 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed complete all as specified and as directed.

Supply and fix 150mm size aluminium anodised handles, fabricated type complete all as specified and as directed.

Supply and fix 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

Supply and fix 150 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy all as specified and as directed.

Supply and fix 250 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

Supply and fix Windows/ ventilators (NCL ECO – 4000 Series Windows (Double Rebate Windows) or equivalent) fabricated from roll framed sections made of galvanized steel colour coated/ powder coated (Base steel as per IS 513 “D” quality galvanized as per IS 277 with zinc of 120 gms/Sqr. Mtr.) with total coated thickness of 0.58mm.Sections for Frame should be of 72mm x 55mm, Section for Mullion should be of 72mm x 50mm, Section for Shutter Frame should be of 47mm x 20mm, Section for Fixed Glass Bead should be of 12mm x 12mm, and Section for Fly Mesh should be of 40mm x 20mm Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion Section should be joined with Frame/Mullion using Mullion Cap Ethyl Propylene Damien Monomer (EPDM) Gasket should be used all around glass in shutter and Fixed Glass. Spoon Section should be used around fly mesh to fix Mesh in Mesh Shutter including SS Pivot Hinges – 1 set, Seccolor Handle & Seccolor Stay and 4MM Plain Float Glass and Stainless Steel 32 gauge Fly mesh of 25 holes per Sqcm and powder coated Grill made of 10mm sq. MS Bars welded at 150mm c/c, 6mm x 12mm MS flat and fixed to window frame with screws complete all as specified and as directed.

Supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc of size 105 x 60 mm complete all as specified and as directed.

Supply and fix pressed steel frames for doors with one or more rebates including necessary fixing lugs hinges lock strike plate etc of size 125 x 60 mm complete all as specified and as directed.

Supply and fix IInd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and as directed..

Material and Labour for PCC 1:3:6 type C0 (using 12.5 mm graded stone aggregate) as in filling in frame complete all as specifed and directed.

Supply and fix mild steel flats 25x3 as in hold fasts all as specified and as directed.

Supply and fix 35mm thick flush door shutters, solid core construction, with block board core and plywood face panels, commercial type face on both sides with lipping to match with frame and fitted to chowkats etc., complete all as specified and as directed.

Supply and fix for glazed and skeleton shutters 35 mm thick 2nd class hard wood open rebated and prepared to receive gauze etc (without sash bars)edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, gauze etc , sizes of memebres of shutters as specified in SSR Part-I section 8 clause 8.24 (a)( wire mesh doors) Supply and fitted to chowkats complete all as specified and as directed.

Supply and fix 100 mm long MS butt hinges with galvanised mild steel hinge pin anodised and fixed complete all as specified and as directed.

Material and Labour for two coats of synthetic enamel paint over a coat of primer including preparation of new wooden surface of any description over 10 cm width and girth all as specified and as directed.

Material and Labour for one coat of synthetic enamel paint including preparation of old wooden surface of any description over 10 cm width and girth all as specified and as directed.

Supply and fix Stainless Steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless Steel wire staples along with frame work of windows / ventilators with all necessary arrangements complete all as specified and as directed.

Dismantling timber scantling as in fillets, rails etc under 40 sqcm in section and fixed in any position complete all as specified and as directed.

Dismantling boarding, cupboards shelves etc. any thickness and description , fixed with nails/screws complete all as specified and as directed.

Material and Labour for 2nd class hard wood plain fillets sectional area exc 13 sqcm but n. exc 25 sqcm square(as in chowkats of CBs) , rectangular in section, wrought and smooth finish, secured with nails or brads complete incl polishing all as specified and as directed.

Material and Labour for 2nd class hard wood fillets sectional area exc 6 sqcm but n. exc 13 sqcm square , rectangular in section, Wrought and smooth finish complete all as specified and as directed.

Material and Labour for 2nd class hard wood fillets ( in beading of CBs shutter) sectional area n. exc 3 sqcm square , rectangular or triangular in section, Wrought and smooth finish but bullnosed, splayed chamfered or rounded on one edge or face complete all as specified and as directed.

Material and Labour for prelaminated Medium density fibre board, 18-19 mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed in repairs with screws to timber frame work for cupboards, shutters and book shelves and kitchen cabinets , drawers etc. complete all as specified and as directed.

Material and Labour forr 25 mm thick prelaminated particle board exterior grade prelaminated both side with decorative choice lamination & other side balancing white laminations fixed with screws to timber formwork complete all as specified and as directed..

Supply and fix continuous (Piano ) Hinges 30 mm width of flaps, mild steel bright finish or electrogalvanised complete all as specified and as directed.

Supply and fix 100mm aluminium barrel tower bolts, stove enamelled black, with bright bolt and fixed all as specified and as directed.

Supply and fix 100 mm size Hasp and staple, Aluminium anodised, wire type, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply and fix 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished all as specified and as directed.

Supply and fix mild steel Mortice locks 65 mm size 4 lever type for cupboards , grade- 1 vertical type complete all as specified and as directed.

Supply and fix MS helical door spring 300 mm long with roller and roller plate complete all as specified and as directed.

Supply and fix Stainless Steel curtain rail / drapery rod 20 mm dia of approved pattern along with decorative SS brackets of approved quality with knob and pattern fixed with screws all as specified and as directed.

Hacking out old broken glass (any thickness size/ quality description) from metal frame including punching or drilling out old glazing pin/spring clips and providing and fixing new one complete all as specified and as directed.

Material and Labour for 4 mm thick,Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, etc completed all as specified and as directed.

Supply and fix 4mm thick figured glass pin head type and glazing with oil putty in square n. exc. 0.50 Sqm in each pane all as specified and as directed.

Supply and fixed in repairs, vitreous china squatting pan, 'orissa' pattern of size 580x440mm white, with integral foot rests including concrete bedding & inc. CI 'P' trap, 100mm, complete all as specified and as directed.

Supply and fixed in repairs, PVC low level flushing cistern 10 litres capacity complete all as specified and as directed.

Supply and fixed in repairs, vitreous china wash basin white flat back size 550x400mm with brackets including cutting for and pinning in ends of brackets or erecting stand including waste coupling CP brass 32mm dia with long screwed shanks & fly nuts & fancy type CP pillar tap complete all as apecified

Supply and fixed in repairs soap dish, vitreous china white, approximate size 160 x 160 x 90mm, fixed to plugs with chromium plated brass screws all as specified and as directed.

Supply and fix CP brass tubular towel rail 600mm long 20mm dia 'D' type in repairs complete all as specified and as directed.

Supply and fixed in repairs for low density polythelyne pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB etc. 32mm bore complete all as specified and as directed.

Taking up or down steel tubing & connections, 15 mm dia complete all as specified and as directed.

Taking up or down steel tubing & connections, 20 mm dia complete all as specified and as directed.

Supply and lay of CPVC pipes of 20mm size, Schedule SDR-11 & plain CPVC SDR fittings for Hot/ cold water for sizes (outer dia) mentioned below including all fittings and solvents all as per manufacturers recommendations and all as specified in SSR Part-I including concealing the pipes in the walls/ ceiling or laying in floors and testing complete all as specified and directed.

Supply and lay of CPVC pipes of 25mm size, Schedule SDR-11 & plain CPVC SDR fittings for Hot/ cold water for sizes (outer dia) mentioned below including all fittings and solvents all as per manufacturers recommendations and all as specified in SSR Part-I including concealing the pipes in the walls/ ceiling or laying in floors and testing complete all as specified and directed.

Material and Labour for Cutting chases ,pinning in making good to facing where required of brick walls and pointed in cement mortar 1:3 for concealed water tubing etc cutting not exc 10 cm girth all as specified and as directed.

Supply and fixed in repairs 15mm long body bib taps fancy type chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferule and fixed complete all as specified and as directed.

Supply and fixed in repairs, CP 15mm, stop valves/ angle cock, fancy type cast copper alloy with crutch or butterfly handle, screwed down, high pressure, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixed in repairs fancy type stop valves/angle cock , chromium plated with long shank and cup (concealed type) completeall as specified and as directed.

Supply and fix 15 mm dia 600 mm long PVC water connection with PTMT nuts and washers all as specified and as directed.

Supply and fixed in repairs CP shower rose 125 mm size with swivel joint and arm fixed in repairs complete all as specified and as directed.

Dismantling /Demolition and breaking of old water tanks(PVC ) of exc 250 and n exc 500 ( 250 to 500 ) Ltrs capacity complete all as specified and as directed.

Supply and Fix, 500 litres capacity Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, 'ISI' marked, three layered (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement including making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part -I (2009) complete all as specified and as directed.

Disconnecting existing tanks,exc 250 & n exc500, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately),etc completed all as specified and as directed.

Supply and fix Gun metal globe or gate valves of 20 mm dia with iron wheel head screwed both ends for iron pipe and fixed in repair complete all as specified and as directed.

Supply and fix 20 mm bore dia ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (min weight 210gms) complete all as specified and as directed.

Supply and fix Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, waste coupling CP brass , washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mm X 460mm with bowl size 410mm X 330mm X 160mm complete all as specified and as directed.

Supply and fixed in repairs110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and laid in trenches and under floor etc incl taking down old pipes complete all as specified

Supply and fixed in repairs 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and laid in treanches and under floors etc incl taking down old pipes complete all as specified and as directed.

Supply and fix 110mm PVC (SWR) bends any radius complete all as specified and as directed.

Supply and fix 75 mm PVC (SWR) bends any radius complete all as specified and as directed.

Supply and fix 110mm PVC (SWR) bends any radius but with access doors complete all as specified and as directed.

Supply and fix 75 mm PVC (SWR) bends any radius but with access doors complete all as specified and as directed.

Supply and fix PVC (SWR) floor trap, plain with grating including jointing with solvent to waste pipe fixed in cement concrete type B-1 (1:2:4), 75 mm dia outlet complete all as specified and as directed.

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

Supply and fix 110 mm PVC (SWR) vent cowl complete all as specified and as directed.

Supply and fixed in repairs for low density polythelyne pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to wall or in floors etc. as in outlet pipe for WHB etc. 40mm bore complete all as specified and as directed.

Supply and fix 140mm floor door stopper of aluminum alloy body and tongue anodised with hard drawn steel spring fixed in floor or bottom of door complete all as specified and as directed.

Supply and fixed in repairs Shelf of PTMT fixed with and including Chromium plated brass screws and wooden / plastic cleats (Minimum weight 300 gms) complete all as specified and as directed.

Demolition of Concrete in sunken floors and pavings exc 15 cm thickness (below or above ground level) otherwise specifically provided complete all as directed .

Material and Labour for Rendering15 mm thick in CM (1:3) on sunken concrete floor surfaces mixed with integral water proofing compound finished even and smooth without using extra cement all as specified and as directed. Note WPC shall be measured & paid separately

Material and Labour for providing and applying brush applied water based PU dispersed polymer modified Elastomeric liquid membrane, ShaliUrethane BTD with Zero VOC or of any approved make-STP/Fosroc/BASF to form the membrane in situ at site with 3 layers of monolithic, seamless finish having >500% elongation. The first layer is to be formed mixing with clean water in the ratio of 1:1 @ 400 Gms per Sqm and shall act as the prime coat to fill in the cavities. This can be brush or roller applied. For spray application, using any airless spray system with recommended nozzle size at 30:1 at 2 bar pressure. Providing and applying the second coat @ 1 kg per Sqm using the soft brush, roller or spray system with the recommended nozzle size on to the primed surface. Providing and applying 50 Gsm fiber cloth over the 1st coat, when substrate till the coat is tacky. Providing and applying 3rd coat @ 1kg/Sqm to finish the application for a thickness of 1.5mm membrane formed in place. The second coat should be applied perpendicular to the first coat for cross linkage and complete as per the specification and all as directed.

Material and Labour for 25mm thick PCC 1:2:4 type BI using 20 mm graded stone aggregate as in foundation,filling in sunken portions and mass concrete complete all as specified and directed.

Material and Labour for PCC type E-2, 1:5:10 (using 40mm graded aggregate) as in filling and mass concrete as in sunken floors compete all as spefified and as directed .

Supply and fix 900 mm x 750mm 1 mm thick size Kitchen plate racks of stainless steel of medium grade type with plug and washers complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150mm dia pipe complete all as specified and as directed.

Material and Labour for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

Material and Labour for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors all as specified and as directed.

Material and Labour for ATT at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same all as specified and as directed.

Material and Labour for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489 -2004 ,Alkali & fungal resistance dirt resistance exterior paint of required ,shade (Company depot tinted) with silicon aditives@ 0.143 lit/10Sqm over and including priming coat of exterior primer applied @0.90lit/10Sqm over new surfaces including preparation complete all as specified and as directed.

Material and Labour for complete removal of existing treatment on walls by scraping ,rubbing washing down etc and fininshing walls with acrylic smooth paint of required shade applied @1.67lit/10Sqm and including priming coat of exterior primer applied @2.2 Kg/10Sqm complete all as specified and as directed.

Material and Labour for 20 mm thick screed bed or bedding layer of mortar in cement 1:6 for laying floor finishes all as specified and as directed.

Material and Labour chequered cement concrete tiles 30cm x30 cm x25mm thick , set jointed and pointed in neat cement slurry with grey cement and pigments all as specified and as directed.

Material and Labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Supply and fix rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming to Fe-410 -W(Gde-E- 250)quality-A complete all as specified and as directed.

Material and Labour For Two coat of Synthetic enamel paint over a coat Zinc chrome primer, including Preparing new steel surfaces any description, over 10 cm width or grith,not otherwise described all as specified and as directed.

Supply and fix 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed.

Excavating in trenches n exc 1.5m wide and not exc 1.5m depth; for foundation, etc not exc 10 sqm on plan and getting out in hard/dense soil complete all as specificed and as directed .

Demolition of precast concrete block masonry, built in cement mortar incl all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specificed and as directed .

Demoltion of cement Concrete of any description and in any position not otherwise specifically provided, complete all as specified and directed.

Material and Labour for Cement concrete type D2 1:4:8 ( 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Material and Labour cement type C1 1:3:6, using 20mm graded stone aggregate in surface channel and drains etc, complete all as specificed and directed.

Material and labour for precast cement concrete block masonry with solid blocks grade 'C4' having minimum average compressive strength of 40 Kg/Sq cm at 28 days and Density not less than 1800 kg/cum all as per IS-2185 (Part-I) 2005 exc. 10cm in width and setting in cement mortar 1:6, complete all as specified and as directed.

Material and labour for Rendering 15mm thick in CM 1:4 on brick work or concrete surface is to be finished even and smooth (without using extra cement) complete all as specified and as directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25cm in hard/dense soil complete all as specified and as directed.

Removal of excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above starting point complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified and as directed.

Material and Labour for Hardcore of broken stone of gauge n.exc 63mm deposited spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and as directed.

Material and Labour for 100 mm thick PCC type E2, 1:5:10 40mm graded stone aggregate in sub base , foundation filling and mass concrete complete all as specified and as directed.

Material and Labour for sand cushion/bed for laying interlocking tiles / paver blocks complete all as specified and as directed.

Material and Labour for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, with gery cement and no pigment, etc completed all as specified and as directed.

Material and Labour for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in copings around the paver block for setting etc including weathering, slightly rounded or chamfered angles and throating and including necessary form work complete all as specified and as directed.

Material and Labour 100 mm thick PCC type B-1, 1:2:4 (20mm graded aggregate) hard standing finished even and smooth without using extra cement. With spike rolling to to surface or making impressions of expanded metal all as specified and as directed.

Removing excavated soil .exc250m but n exc 500m and depositing where directed complete all as specified and as directed.

Material and Labour for forming 12mm thick expansion joint filled with preformed bituminus filler and top 30 mm primed and sealed with sealing compound Grade 'A' for 100mm thick concrete floor complete all as specified and as directed. .

E/M ITEMS

Taking down existing unserviceable point wiring of any description/type/ size of light/ fan/tube/power/two way/bell point etc on TW batten/conduit including removal of batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified and directed

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as per existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Material and labour for point wiring with 1.5 Sqmm (nominal area) FRLSH ,PVC insulated, unsheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit 25mm dia and its accessories fixed on wall/ ceiling and trusses with suitable clamps , screws etc including one run of 1.5 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.5 mm complete all as specified all as specified for :-

(a) One light point controlled by one, one way switch 6 A, SP

(b) One ceiling fan/exhaust fan point controlled by one, one way switch

(c) One bell point controlled by one bell push.

(d) One light point controlled by two nos, 2-way, 6 Amps switch.

(e) One 3 point 6 Amps switch socket outlet point controlled by one switch on the same board.

(f) One 3 pin 6 Amps switch socket outlet point controlled by one switch on independent board.

Material and labour for point wiring with 4 Sqmm (nominal area) PVC insulated, FRLSH unsheathed, multistrand, 1100 volts grade copper conductor cable single core, drawn through with and including non metallic PVC conduit 25mm dia and its accessories fixed on wall/ ceiling/ trusses /steel structure with suitable clamps , screws etc including one run of 4 Sqmm PVC insulated copper conductor cable green in colour for continuous earthing, 1.6 mm thick MS terminal box finished to wall steel structure and with 3 mm thick laminated hylam sheet top cover all as specified for One 5 pin 5/15 amps socket point on independent board complete all as specified and directed

Supply and fix Switch piano type single pole one way flush type 6 Amps capacity 230 volts all as specified and directed.

Supply and fix Switch piano type, single pole, two way, 230 volts, complete all as specified and directed.

Supply and fix bell push piano flush type 6 Amps, single pole, one way complete all as specified and directed .

Supply and fix switch socket combination 2 in 1 multipurpose 2/3 pin 6 Amps flush type complete all as specified and directed .

Supply and fix Socket, two-in-one, 5 pin, 6 Amp, 230 volts, complete all as specified and directed.

Supply and fix Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal complete all as specified and directed.

Supply and fix ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified and directed.

Supply and fix stepped type electronic ceiling fan regulator AC 230 Volts suitable for 1200 / 1400 mm sweep complete all as specified and directed.

Supply and fix Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

Supply and fix LED lamp 9W complete all as specified and directed

Supply, fix, test and commissioning of Wall mounted LED tube light fittings1x22 Watts, 230 Volts Decorative ultra slim aluminium LED lighting fixture with high lumen output, environmental friendly, energy efficient with all accessories, prewired all as per Cat No.LHEXBTP7IN1S022 of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling with necessary hanging/fixing arrangements and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply, fix, test and commissioning of 10Watts LED decorative Bulk head light fittings, ultra modern, environmental friendly, energy saving, surface mounted oval bulk head edge-lit LED luminaire 10 Watts comprising of high brightness LEDs with minimum 800 lumens, made of pressure die cast aluminium housing, IP65 protection all as per Cat No.RUGBYNEONFT 10WLED860SSYMTOPC of Havells or techno-commercially equivalent of other specified makes complete with all accessories internally prewired including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size etc., complete all as specified and as directed.

Supply and fix Call Bell, AC, ding dong type 230 Volt all as per Cat No.10489 of Anchor or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Disconnecting and removing ceiling fan of 1200 mm sweep any height from electrical connection bringing down, dismantling, cleaning internally and externally thoroughly examine replacement of split pins, cotter pins and check nuts etc overhauling, lubricating with approved lubricants, reassembling, including replacement of wornout/defective parts, refixing in original position including minor repairs for the smooth functioning and provision of new flexible wire of size 23/0.0076 multistranded copper conductor cable 3 core drawn through and including flexible conduit 15mm size from ceiling rose to fan including painting of ceiling fan complete cleaning all dust etc and testing complete all as specified.

Supply and fixing ceiling fans in repairs complete with blades, down rods and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) all as specified and directed. Note:- The BER/ u/s ceiling fan shall be deposited to AGE E/M store.

Material and Labour for Submain wiring with two single core 6 Sq mm FRLSH ,PVC insulated unsheathed copper conductor multistranded 1100 Volts grade drawn in and including concealed rigid PVC conduit of suitable dia, conduit fittings and accessories concealed in wall/floor with one run of 6 sqmm, FRLSH,PVC insulated unsheathed copper conductor cable as earth continuity conductor along the wiring and connected to the common earth dolly complete including removing the existing unserviceable sub main wiring and making good the disturbed surface to match with the existing all as specified and directed. Note: Two runs of 6 Sqmm cable, one run of 6 Sqmm earth contuinity conductor and one run of conduit shall be measured and paid as one unit length.

Material and Labour for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of andings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

Supply & Lay on wall/in ground/on pole ISI marked XLPE insulated armoured, heavy duty, electric cable with aluminium conductors 1100 volts laid in floors, ducts, pipes drawn across the road/paths/drain/along poles/walls/floor/equivalent etc including jointing & testing complete of size 25 Sqmm 4 Core all as specified and directed.

Supply and fix GI pipe of 50 mm nominal dia light grade fixed to poles or laid under road crossing or fixed to wall complete all as specified and directed.

Supply, fix, connecting and testing factory made, vertical distribution board (MCCB DB), IP 43, IK-09, metal double door, Supply and fix sheet metal enclosure Line load distribution board TPN 4 Way with 200 Amps rated bus bar 415 volts, with MCCB TPN as incoming and 12 out going SP MCB's double door with suitable locking arrangement concealed and fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed. Note :- The unit rate quoted shall be deemed to include the cost of cutting chases into walls for concealing MCCB DB and making good the disturbed surfaces with cement work and finishing the surfaces to match with the existing surface.

Supply and Fix MCCB 4P suitable for fixing on 4 way TPN DB of capacity 63 Amps complete all as specified and directed.

Supply and fixing sheet Metal enclosure double door type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete all as specified and as directed

Supply and fixing MCB SPN 40 Amps , 240 volt, 10 KA, complete all as specified and as directed

Supply and fixing MCB single pole 40 Amps , 240 volt, 10 KA, complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge.

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz all as per Ventil Air - DB of Havells or techno-commercially equivalent of other specified makes including cutting hole in to the wall / existing window / ventilator etc., and making good the disturbed surfaces and connecting up complete including provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose complete all as specified and as directed. Note :- The unit rate quoted shall be deemed to include the cost of making hole in walls/other surfaces, making good the disturbed surfaces including any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan and matching to the existing surface.

Supply, install, testing & commissioning of Exhaust fan, PVC body with automatic back shutter louvers 300 mm sweep, 1280 RPM or more, Air Delivery not less than 860 CMH, single phase, 240 Volts, AC, 50 Hz all as per Ventil Air - DX White of Havells or techno-commercially equivalent of other specified makes including cutting hole in to the wall / existing window / ventilator etc., and making good the disturbed surfaces and connecting up complete including provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose complete all as specified and as directed. Note :- The unit rate quoted shall be deemed to include the cost of making hole in walls/other surfaces, making good the disturbed surfaces including any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan and matching to the existing surface.

Supply, Install, testing and commissioning of Vertical type Storage electric water heater (Geysers) of 25 Ltrs capacity, tank made of ultra thick super cold rolled steel plates with high density PUF insulation, 2 KW, 230 V, Single Phase, 50 Hz, AC, BEE 5 Star rated all as per Cat No: GHWAMGTWH025 (Monza DX) of Havells or techno-commercially equivalent of other specified makes including provision of multifunction safety valve including suitable plug top and grouting and fixing with and including 2 Nos anchor fasteners of size as per manufacturer's instructions, making good the disturbed surface complete and connecting electrical and water supply connection using steel braided hose 2 Nos, testing and commissioning etc.,complete all as specified and as directed. Note: (i) Installed Geyser's warranty card should be submitted to the GE duly verified by Engineer-in-Charge before claiming payment for Geysers. (ii) CA No. Year and Qtr No. shall be written on the new geysers by Black synthetic enamel paint using stencils or by permanent marker pen and the unit quoted shall be deemed to include the cost of writing these details.

Supply, fix, test and commissioning of energy saving and environment friendly long life LED building security light of 25Watts with high efficient led as lighting source, minimum 2500 Lumens with LED driver made up of pressure die cast aluminium housing and with PC cover as diffuser having top opening, separate driver compartment with IP66 protection and impact resistance of IK07 suitable for operation on AC single phase 220-240 Volt, 50 Hz supply all as per Cat No.ENDURAPEARLSL25WLED757SASYTOPCMP of Havells or techno-commercially equivalent of other specified makes fixed with and including GI pipe bracket made out of 40mm dia light grade pipe of length 1.2 Mtrs, bend to shape 120-130 degree and fixed on wall with 2 Nos MS clamps made out of 25x3mm flat iron painted with two coats of synthetic enamel paints over a coat of red oxide primer including nuts, bolts and washers etc., and making connections through and including flexible conduit from ceiling rose to fitting etc., complete all as specified and as directed.

Material and Labour for Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick, buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less' than 1.5meters below normal ground level, earth plate connected to galvanized earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES SSR-2009 (part I Specifications) connected to earth test point all as specified or indicated including testing on completion, including necessary excavation and earth work in any type of soil and adequate quantity of common salt & charcoal for alternate layer around the earth plate, including PCC (1:2:4) pit and 10mm thick C.I. cover with arrangement of hinge to 40x40x6mm C.I. angle iron frame, including 20mm dia G.I. pipe for watering purpose with the arrangement of funel and wire mess, including GI pipe of 15 dia for earth lead protection complete all as specified and as directed.

Material and Labour for Earth Continuity conductor or main earthing lead 4mm galvanised iron or steel wire including GI protection pipe light grade 15mm bore fixed to wall or recess or chases or buried in ground or any other indicated situation complete all as specified and directed

Supply lay/spread in trenches clean river sand including spreading levelling punning for laying /cushoning of cable all as specified and as directed Note: Punned thickness only will be Considerd for payment.

Supplying and laying reinforced precast concrete cable cover, class s LV, Type I, flat, size 250 mm x 150mm x 40mm all as specified and as directed

Dwarka Pershad Radhey Ramanlal

B.N.S Constructions

UNITED TECHNO PROJECTS PVT LTD

TRIVENI CONSTRUCTIONS

Sri Raghava Constructions Ltd

R. Wadhumal and Sons

Shekhar Enterprises