M/o Completed Scheme under NA-II ( Horticulture Zone)

Deployment of staff for day to day maintenance of electrical installation / sub -station /pump houses etc. as per terms and conditions attached.

Supplying of following sizes of XLPE insulated PVC sheathed armoured aluminium conductor power cable of 1.1KV grade including connections and testing etc. as required. a) 2x16 sq. mm

b) 4x25 sq. mm

c) 4x50 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.I kVgrade of following size direct in ground including excavation, and refiling the trench etc.as required but excluding sand cushioning, protective covering. (a) Upto 35 Sq. mm

(b) Above 35 Sq. mm and upto 95 Sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following sizes in the existingRCC/HUMEMETAL pipe as required. a) Upto 35 Sq. mm

b) Above 35 Sq. mm and upto 95 Sq. mm

Supplying and making straight through joint with heat shrinkable kit including ferrules and other jointing materials for following size of PVC insulated and PVC sheathed /XLPE aluminium conductor cable of 1.1 KV grade as required a) 2x16 sq. mm

b) 4X25 sq. mm

c) 4x50 sq. mm

d) 3.5x95 sq.mm

e) 3.5 x 150 sq.mm

LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying and Replacement of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 °C to 50 °C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%, THD 10% as per IEC 61000-3-2, P. F.20.95, IP-66,IK-10, CRI 270, under voltage and over voltage protection, EMI- EMC As per CISPR 15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K /5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 Im/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). a) 45 watt

Supply & replacement of pole connector box made out of Glass Reinforced Polyester Sheet Moulding Compound Conforming to IS:13410-1992 Grade S1 of outside dimensions 280 mm(H) x 170 mm(W)x 115 mm (D) (all the corners of the box should be round & not pointed ones) suitable to mount on 40/50/65 mm dia GI pole with the following provisions/accessories mounting in box complete as reqd. (i)2 nos. clamps made out of 19mm x 3 mm GI strip of suitable length for mounting box on the pole (if required). (ii) Water tight front cover with 2 nos. stainless steel hinges & 1 no. screw for tightening. (iii)4 way, 220 V, 30 A, dough moulded connector (SMC with stainless steel inserts) - 1 No. (iv) 16 amp. Moulded SMC rewireable kit-kat---1 no. (v) Suitable size hole at suitable location on rear wall for cable & wire entry in the connector box. (vi) Earthing bolt M6 x 20 mm

LED Flood Light, powder coated pressure diecast aluminium (System lumen efficacy ≥120 and<135 lm/Watt. Supplying and Replacement of Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 °C to 50 °C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%, THD 10% as per IEC 61000-3-2, P. F.20.95, IP-66,IK-10, CRI ≥70, under voltage and over voltage protection, EMI-EMC as per CISPR-15, lenses for beam angle 30 deg-120deg as per the application and the project requirement, suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 and <135 Im/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). a) 70 watt

a) 100 watt

b) 250 watt

Supplying and Replacement 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB/panel complete with connections, testing and commissioning etc. as required. a) Single Pole

b) Single Pole Neutral

b) Double pole

c)Triple pole

e) 32A Ac-3, 3 Pole power contactor

f) Analogue Time Switch

b) 3x2.5 sq.mm

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Providing and fixing 6 SWG dia G.I. wire on surfaceor in recess for loop earthing as required

Lifing out of sewage submersible pump set/veda pump from the bore well up to the required depth alongwith existing Gl pipe, sub. Cable & accessories etc. ile dismantling of G.I pipe and disconnecting the cable etc. complete as reqd

Lowering & commissioning of sewage sub. pump/veda pump set in the bore well up to the required depth along wit

h existing G.I pipe and sub. cable cte., water proof jointing of sub. cable, replacement of reqd. nuts, bolts, washers and packing, nipple, reducer etc. complete as reqd.

Supplying and replacement of PVC sheathed, PVC insulated copper conductor flat submersible cable of size 1 x3 x2.5 sq. mm i/c connection testing ctc. complete as reqd.

Supplying & replacement of following size of double flanged Gi pipe 'B' class duly threaded & welded with necessary pipe fittings, bends, elbow etc. complete as reqd a) 50 mm dia.

b) 65 mm dia.

Repairing & rewinding of sub. motors of following capacity with cartage, dismantling, reassembling i/c supply & replacememt / repairing of damaged parts of motors and making good for operation i/c connection, testing, painting etc. complete as reqd. b) 3 HP to 5 HP ,3 phase sub motor

a) From 6 to 7.5 HP 3 phase sub.motor

Repairing of sub. pump of the following stages & dia with cartage, dismantling, reassembling, supply & replacement / repairing of damaged parts of pump and making good for operation i/c testing, painting etc. complete as reqd. a) 6"dia submersible pump sets upto 5 stages

b) 6"dia submersible pump sets 6 stages & upto 8 stages

Repairing & rewinding of 3 phase, 415V, 1440 RPM, 20 HP, induction motor duly coupled with sewage treated water pump set i/c supplying & replacement of suitable ball bearing-2 Nos. (SKF), Connection Plate-1 No. i/c dismantling, cartage, refixing, connection, testing etc. complete as reqd

Repairing & rewinding of 3 phase, 415V, 1440 RPM, 40 HP, induction motor duly coupled with sewage treated water pump set i/c supplying & replacement of suitable ball bearing-2 Nos. (SKF), Connection Plate-1 No. i/c dismantling, cartage, refixing, connection, testing etc. complete as reqd.

Repairing and servicing of sewage treated water pump set (model SHM 100/26 Kirloskar make) i/c supplying and replacement of following parts i/c dismantling and labour, cartage, refixing, commissioning, testing etc. complete as reqd. a) Remetaling & repairing of pump shaft i/e turning & grinding etc. -1 Job. b) S/R of ball bearing (No. 6309)--2 Nos.(SKF). c) S/R of gland sleeve S.S-1 set.. d) S/R of gland plate -1 set. e) S/R of Gland stud--2 No. f) S/R Impeller nut-----1 No. g) S/R of complete set of body studs-- 1 set.

Repairing and servicing of sewage treated water pump set (model SHM 80/26 Kirloskar make) i/c supplying and replacement of following parts i/c dismantling and labour, cartage, refixing, commissioning, testing etc. complete as reqd. a) Remetaling & repairing of pump shaft i/e turning & grinding etc. -1 Job. b) S/R of ball bearing--2 Nos.(SKF) c) S/R of gland sleeve S.S-1 set. d) S/R of gland plate -1 set. e) S/R of Gland stud--2 No. f) S/R Impeller nut-----1 No. g) S/R of complete set of body studs-- 1 set

Repair of Existing oil immesred Star delta starter i/c replacement of faulty overhead coil, brass finger and fixing ,Thimble,SS nut, bolts etc. complete as required.

Supplying & replacement of following control gear accessories in the existing installation for electric panel board, motor starter, connection testing etc. as reqd a)63 AMP TPN MCB (C- Curve )

b)Single phase preventor

c)DOL Starter suitable up to 7.50HP Pump set

d) overload relay (9 to 14) Amp. For DOL starter

e)No Volt coil for DOL Starter

f)125 A, 4P, 36 K.A. MCCB

g)250 A, 4P, 50 K.A. MCCB

Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with ISI marked HRC fuses including drilling holes in cubicle panel, making connections, etc. as required a) 63 Amp TP&N

b) 125 Amp TP&N

c) 200 Amp TP&N

Hire charges for cable fault locating machine to locate the fault in the existing underground LG cable etc. as reqd.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

Supplying ,replacement and installaton following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenientsections, joined with connectors, suspended from the ceiling with two numbers MS/GI Suspenders i/c baseof suitable size MS/GI angle, bolts & nuts, painting suspenders, fastener etc as required a)100 mm width X 50 mm depth X 1.6 mm thickness

b)300 mm width X 50 mm depth X 1.6 mm thickness

c)450 mm width X 50 mm depth X 2.0 mm thickness

Dismantalling of existing damaged booster pump foundation upto required level and recasting the same after repairing and replacement of foundation bold, steel bar including fixing of existing base frame, dismentaling & refixing of booster pump sets etc. complete as reqd.

Repairing & rewinding of sewage submersible pump sets of Following capacity including repairing/replacement of bearing set, mechanical seal, O-ring set, cable gland, worn out stud nut and making good for operation including testing, painting, Lowering/lifting & cartage to & fro of sewage submersible pump etc. complete as required. a)5 HP

Repairing & rewinding of Dewatering pump sets of Following capacity including repairing/replacement of bearing set, mechanical seal, O-ring set, cable gland, worn out stud nut and making good for operation including testing, painting, Lowering/lifting & cartage to & fro of sewage submersible pump etc. complete as required a) upto 3 HP

Repairing of existing feeder pillar i/c replacment of 2 mm thick CRCA sheet in front / side door with welding of hinges, gasketted cover, handle, locking arrangement painting with both sides etc as reqd

Digging out of 1 no. faulty PVC insulated, PVC sheathed/XLPE power cable laid in ground and relaying of the same after removing of the cable fault i/c refilling and redressing of the trench etc. as reqd

Complete Repairing/Rewinding of 3 Nos. HT& LT limbs of transformer ( of Rating 400 KVA), changing of insulation and gaskets, baking the core & winding in automatically controlled hot air circulation oven, Dehydration & filtration of transformer oil, applying heat resistance paint inside of tank, its complete fitting, unloading& loading at our site, complete as required.

Supplying & replacement of oil immerged star delta starter upto 100 HP capacity suitable for booster pump operation of upto 60 HP capacity including Filling of suitable quantity of oil ,

connection, testing etc. complete as reqd.

Painting & numbering/ naming of all the electrical installation (booster pump sets, CI/MS/GI pipe, valves, panel etc. complete) inside the pump house as reqd.

Lowering & Lifting of ring from the poles (above 10 mtr only) by the means of keys and other accessories along with electric fittings for replacement of faulty fittings and replacement of faulty fittings by climbing up of the poles (above 10 mtr only also providing suitable climibing tool like hydra, crane etc as per requirement ) (also providing suitable climbing tool like hydra, cranes etc. as per requirement) i/c replacement of accessories from poles (above 10 mtr only) and panels and other related electrical work as decided by Engineer-in-charge etc complete as required.

Supplying and replacement of manually operated gear box ( with complete head and pulley) having simple Gear and pinion arrangement made up of bronze with 2 nos of Drum and bush etc complete as required.