Upgradation and Renovation of EI in Various Buildings at Tata Memorial Cancer Hospital Distt. Sangrur

Upgradation/ Renovation of EI in Various Buildings at Tata Memorial Cancer Hospital

XLPE INSULATED HT CABLES:

XLPE INSULATED HT ARMOURED CABLES (LOOSE):

Supply & laying of Circular Aluminium Conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FR PVC inner sheathed, galvanized steel strip armoured and overall FR PVC sheathed cable confirming to IS:7098 (Part-2), 2011 working voltage 11KV(E) grade to be laid loose in the existing trench or pipe:-

HT Cable Overall size 95sq.mm (3Core) (From VCB room to CSS 630KVA) (2 Runs)

Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS 458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed. The pipes shall rest on the beds at all joints through their lengths and fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc.

R.C.C. Pipe NP -3

150mm i/d pipe

S/E of Heat shrinkable cable end termination/ Straight through joint kit for 11 KVA /6.6 KV (E) XLPE Cables as approved & desired by Enginer in charge:-

Heat Shrinkable End Termination for cable size 50-95 sq. mm, 3Core (Indoor Type)

COPPER EARTHING (Upto 14 metre in Length):

Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Earthing with 40mm x 5mm Copper Tape (upto 14Metre in Length)

COPPER EARTHING STRIP (As Additional Length):

Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:-

Additional Length 40mm x 5mm thick Copper Tape

XLPE INSULATED UN-ARMOURED CABLES (LOOSE):

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Overall size 95sq.mm (3½ Core) Un-armoured (Loose)

Overall size 240sq.mm (3½ Core) Un-armoured (Loose) (For Girls Hostel)

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)

Double Walled Corrugated HDPE Pipe 120/ 103.5mm (Outer/ Inner dia.)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 50sq.mm

Aluminium thimble cable Core size 95sq.mm

Aluminium thimble cable Core size 120sq.mm

Aluminium thimble cable Core size 240sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 95-120sq.mm

Brass Gland for Aluminium cable 3/3½/4 Core size 240sq.mm

Supply, Erection, Testing and Commisioning of HT 11kV 630KVA Package Substations is completely self-contained Solution for power distribution that includes Pre fabricated outdoor duty enclosure, high voltage switchgear, distribution transformer, low voltage panel and accessories such as power factor improvement equipment, control and protection equipments, all providing a cost effective. The complete unit shall be installed on a substation plint (base) as outdoor substation. Package substation shall have the following equipments: 11kV Switchgear: 11 kV, 3 Phase, SF6 compact switchgear panel with 11kV Load break switches controls incoming-outgoing feeder cables of 11kV ring main distribution system and Vacuum circuit breaker (VCB) as protection to the transformer. The Load break switch, Vacuum circuit breaker, Bus bars should be mounted inside a sealed robotically welded stainless steel tank enclosure. The operating mechanism of switches and breakers shall be outside the SF6 tank and accesible from front. The tank should be filled with SF6 gas at an adequate pressure. The degree of protection for gas tank should be IP67.

There shall be provision for filling the SF6 gas at site. Stainless steel gas tank shall confirm to the sealed pressure system and ensure the gas leakage to 0.1% per year as per IEC 60298. The Panels shall be tested for IAC level of min. 21kA/1 Sec. No. of operations of Vacuum interrupter bottles for better performance (i) At rated current: 10,000 operation (ii) No. of short circuit dead operation at rated short circuit current: 40 opeartion. Load break switch parameters are as below: (a). 11kV, 3Phase HT manually operated Load break switches 630Amp., copper busbars with integral earth switch having ON/OFF/EARTHED indiaction, live cable indiaction cable termination bushing suitable for 300sq mm XLPE cable. (b). Type: Load breaking and fault making in SF6 tank (c). Fault making capacity : 52.5kAp (d). Operating Mechanism: Operating handle with ON, OFF, Earth positions with arrangement for padlocking in each position

Transformer: 11KV/433V Distribution Transformer, Three Phase 50 Hz, Oil Immersed, Naturally Cooled ONAN, Core type double wound with copper conductor cnforming to IS:1180 (2021) Level-2 As Per Amdedment-4 / IS: 2026, vector group Dyn11 suitable for packaged substation housed in a enclosure with corrugated tank arrangement hermeatically sealed. Transformer parameters are as follows: (a). Off Circuit Tap changer: +5% to -10% off circuit tapping in steps of 2.5%. (b). Permissible Temp. Rise of Oil: 40°C (c). Permissible Temp. Rise of Winding 45°C (d). Magnetic Core: Prime grade of M4 or better (e). System Highest Voltage :- 12kV at the HV side (f). Terminations: Cable Box on HV & LV Side (g). Insulation Level: ● H.V. Power Frequency (KV rms) : 28 kV ● H.V. Impulse withstand voltage (KV peak): 75 kVp

Enclosure for PSS: Outdoor type enclousre shall be made of 2mm thickness of galvanised sheet steel tropicalised to meet indian weather conditions including all the partition sheets and doors. The enclosure shall be corrugated type wall design for better heat dissipation, provinding robust construction and enclousre should have IP54 degree of protection for HT & LT switchgear compartment & IP 23 protection for transformer compartment. the base of the enclosure shall be of 4mm thickness hot dip galavanized sheet steel to ensure rigidity for easy transport & installation. The entire package substation shall be factory assemble & factory fitted. Each compartment should be provided with the door and pad locking arrangement. The unit shall be tested for internal arc fault test to the tune atlest 20kA for 1 second as per latest IEC 62271-202. Interconnection & Earthing: Interconnection between HT switchgear & transformer using screened covered aluminium XLPE single core cable & interconnection between transformer & LT switchgear using aluminium busbars with copper flexibles. Internal earthing connections by 50x 6mm G.I strips.

LT switchgear: (a). LT switchgear with 433V suitable ampere rating Aluminium busbars with 100% neutral (b). 1 No. MCCB/ ACB FP microprocessor based for O/C, S/C & Integrated E/F release type for incomer according to the KVA rating of the transformer Metering compartment: (a). 1 No.Digital multi functional meter class1.0

Package Substation 11kV HT Switchgear with 3 way RMU (RRL), consisting of 2 Nos. manually operated Load Break Switch 630 Amp., 1 No. manually operated SF-6 VCB 630 Amp., 11KV/433V, 630KVA ONAN type transformer, 1 No. ACB 1000Amp., FP, 50KA microprocessor based. Level-2 ( As per Amendment-4) labeled Distribution

With the provision of Attached Outdoor Panel having Incomer:- Air Circuit Breaker Four Pole, 1000amp., 415volts (Electrical Draw-Out Type), Outgoing:- MCCB Four Pole 125amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting = 3 No's, MCCB Four Pole 400amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting = 1 No, MCCB Four Pole 630amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting = 1 No

Shifting of 250 KVA DG Set from Surgical Block to RT Block

XLPE INSULATED UN-ARMOURED CABLES (LOOSE):

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Overall size 185sq.mm (3½ Core) Unarmoured (Loose)

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Double Walled Corrugated HDPE Pipe 120/103.5mm (Outer/ Inner dia.)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 95sq.mm

Aluminium thimble cable Core size 185sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 185sq.mm

COPPER EARTHING (Upto 14 metre in Length):

Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Earthing with 25mm x 5mm Copper Tape (upto 14Metre in Length)

COPPER EARTHING STRIP (As Additional Length):

Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:-

Additional Length 25mm x 5mm thick Copper Tape

Shifting Charges of 250 KVA DG Set from Surgical Block to RT Block in Tata Memorial Cancer Hospital

MCCB's (FOR PANELS & SHEET ENCLOSURE):

Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubical type) in the existing Cubical Panel (confirm to IEC:60947-2) having Ics=100% Icu, 100% neutral with spreader terminal links, Extended rotary handle and relevant PWD general specifications complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with suitable size of thimbles etc:-

MCCB Four Pole 400amp., 415volts, ≥36kA Microprocessor Based Adjustable Thermal and Magnetic Setting

Shifting of 125 KVA DG Set from RT Block to Girls Hostel in Tata Memorial Cancer Hospital

XLPE INSULATED UN-ARMOURED CABLES (LOOSE):

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Overall size 95sq.mm (3½ Core) Unarmoured (Loose)

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 50sq.mm

Aluminium thimble cable Core size 95sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 95-120sq.mm

COPPER EARTHING (Upto 14 metre in Length):

Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Earthing with 25mm x 3mm Copper Tape (upto 14Metre in Length)

COPPER EARTHING STRIP (As Additional Length):

Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:-

Additional Length 25mm x 3mm thick Copper Tape

Shifting Charges of 125 KVA DG Set from RT Block to Girls Hostel in Tata Memorial Cancer Hospital

Providing of LT Cable from RT Block Sub Station to MRI Block

XLPE INSULATED Un-ARMOURED CABLES (LOOSE):

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Overall size 240sq.mm (3½ Core) Un-armoured (Loose)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 120sq.mm

Aluminium thimble cable Core size 240sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 240sq.mm

PCC POLES:

Supply and erection of pre-stressed cement concrete pole of suitable length with a given planting depth confirming to IS-1678/ 1960/1978 below ground level in excavated pit of suitable dimensions complete in all respect as approved by Engineer-in-charge at site:-

PCC Pole Overall Length 9 metre, Planting depth 1.5 metre, W/L 200 kg.

JUMPERS FOR OVERHAED LINES:

Supply stringing and sagging of aluminium conductor steel reinforced (ACSR) on poles including binding with insulators using aluminium wires complete as desired by the Engineer in charge of the site:-

ACSR-WEASEL conductor (30 sq. mm) Size (6/2.55 Al.+1/2.55mm GI)

HT & LT LINE ITEMS:

Supply & erection of 'V' shape cross arm of MS channel 75mm x 40mm as per standard drawing. The item include supply and erection of half clamp made out of 50mm x 6mm flat including cost of nut and bolts as approved by Engineer-in-charge.

Upgradation Of Existing Electrical System for Surgical Block

COPPER EARTHING (Upto 14 metre in Length):

Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Earthing with 40mm x 5mm Copper Tape (upto 14Metre in Length)

COPPER EARTHING STRIP (As Additional Length):

Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:-

Additional Length 40mm x 5mm thick Copper Tape

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 240sq.mm

Aluminium thimble cable Core size 400sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 400sq.mm

Designing, Supply, Erection, Testing & commissioning of AMF indoor Type cubical panel enclosure (dust, vermin and interchangeable modules with facilites for extensions or reduction as per the space or requirments). The Panel shall be suitable for operation at 415+6% Volts, 50HZ, 3 phase 4 wire & earth system. The assembly manufacturer should be ISO approved and CPRI tested for short circuit of (minimum 50kA) as well as IP degree of protection (IP 54/55). Fabrication:- Panel shall be made from 14/16 SWG CRCA sheet, conforming to IS 8623/1977-82. The sheet metal used for the fabrication of control panel will be 2mm for load bearing member’s door and fittings plates etc. the partitions and other non load bearing members will be fabricated out of 1.6mm sheet, the sheet will be of mild steel CRCA type. The base channel will be made out of 75 x 40 x 5mm rolled channel.

The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The panel door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. Minimum depth 400mm / wide 300 mm for busbar/ Cable ally at the front of the panel. The panel will be free standing floor mounting type having provision for cable entry from bottom/top with cable glands etc.

The fabrication should be such that all the member i.e. vertical/horizontal should be detachable type i.e. total bolted. In case of any changes required at site. it should be possible then and their self without any cutting or welding. The fabrication of the panel in 3B construction fully compartmentalized type i.e. bus bar chamber as well as the cable chamber should be totally isolated from the feeder chamber. Where there crossing of the wire or bus links. It should have proper rubber gourmets or non-hygroscopic material. No live part should be in visible condition.

Painting:- The sheet metal is sprayed with corrosion resistant etch Primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work . Busbars:-The panel shall be provided with TPN aluminium busbar of suitable size according to the size of MCCB's. Busbar shall be of high conductivity (53% to 58%) E91-E Grade aluminium (1A/Sq.mm). All Busbar will be air insulated with codified in Red, Yellow, Blue & Black as per standard for cable termination with the help of extended busbar only with proper adjustable cable supports. The main busbar would be supported upon non-hygroscopic SMC/DMC supports.

With Air Circuit Breaker Four Pole1000amp., 415volts (Electrical Draw-Out Type) =2 No with necessary contactor, Indicator, Metering and other allied accessories

Providing DG Set 320 KVA with AMF Panel for Surgical Block

XLPE INSULATED UN-ARMOURED CABLES (LOOSE):

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-

Overall size 300sq.mm (3½ Core) Unarmoured (Loose)

DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:

Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-

Double Walled Corrugated HDPE Pipe 160/136mm (Outer/ Inner dia.) (For DG Set Cable)

Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-

Aluminium thimble cable Core size 150sq.mm

Aluminium thimble cable Core size 300sq.mm

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 300sq.mm

Supply, Erection, Testing and Commissioning of Water Cooled Silent DG Set 320 KVA with Standard Control Panel, Three Phase, 415Volts, 50Hz, 1500 RPM Silent (Sound Proof) Diesel Generator Set. It should be Water cooled naturally aspirated/ turbo charged/ turbo charged after cool (As per manufacturer standard). DG Set should be operated/ controlled through AMF Panel as well as Manually ENGINE: The Diesel engine developing suitable BHP for giving a power rating as per ISO 8528- Part-1 (With CPCB-IV Norms) in KVA at the load terminals of alternator at 1500 rpm at actual site conditions. The engine shall confirm to IS 10000/ ISO 3046/ BS: 649/ BS 5514 amended up to date have dynamically balanced Fly wheel, air cleaner (dry/ oil bath type) as per manufacturer standard. A electronic governor of TYPE A1 AND A2 to maintain engine speed at all conditions of load, daily fuel service tank of minimum 8 hours running capacity as per manufacturer standard, Dry exhaust manifold with suitable exhaust residential grade silencer to reduce the noise level.suitable self-starter for 24 V DC, battery charging alternator unit and voltage regulator, Lubrication oil cooler,Lubrication oil filters with replaceable elements.

ENGINE CONTROL PANEL: Engine control panel fitted and having digital display i.e Start/stop key switch/push button, Battery charging indication,Engine Hours indications, Over speed indication, High water temperature indication, Lubricant oil pressure indication,) RPM indication. ALTERNATOR: The alternator should be designed as per (IS4722 and IEC:34 ) standard. Rated Power Factor : 0.8 (lag), Rated voltage : 230/415 volt, SPDP (Screen Protected Drip Proof), Degree of protection: IP-23, Ventilation: Self ventilated air cooled

Alternator should have 40 degree maximum class H insulation, Automatic voltage regulator unit should be provided as per standard practice of manufacturer. Its voltage dip shall not exceed more than 20% of the rated voltage at any step load or transient load as per ISO 8528 (Part-1). Its efficiency at full load 0.8 power factor, 10% overload one hour in every 12 hrs of continuous use. ACOUSTIC ENCLOSURE: The enclosure shall be fabricated out the CRCA sheet of thickness not less than 1.6 mm on the outside cover with inside cover having not less than 0.6 mm thick perforated powder coated CRCA sheet. It should be IP54 Suitable for outdoor installation exposed to weather conditions, noise level up to 75 dB (A). All sheet metal parts should be processed through 7-tank pre treatment process and batteries accommodated in the battery rack .The acoustic lining should be made up of high quality insulation material i.e. Rockwool / glass/ mineral wool / PU foam of appropriate thickness & density for sound absorption.The inside of enclosure should be provided with at least one no. 28 W-T5 fluorescent tube light/ LED 10Watt luminaries controlled by a 5A switch for adequate lighting during servicing etc.

MANUAL CONTROL PANEL: Manual control panel shall be fabricated out of 1.6 mm sheet steel, totally enclosed, dust, damp and vermin proof wall mounted/ free standing floor mounted type with IP-53 degree of protection & front operated, composite meter for digital display, HRC fuses of suitable rating. MCCB (Fixed Thermal and Adjustable Thermal protection)/ ACB (Over cuurent/ overload, shorcircuit, instantenous, earth fault protection) should be used. Battery charger complete with voltage regulator, Voltmeter and Ammeter for charging the battery from external mains. This will be in addition to the battery charging alternator or dynamo fitted on the engine.All the components in the control panel shall be properly mounted, duly wired and labeled. Suitable terminals are to be provided for panel incoming and outgoing connections. System opeartion facility provided shall afford the following operational requirements. Necessary instruments and accessories such as voltmeter, power factor meter, KW meter, KWH meter, Ammeter, Frequency meter,battery charger complete in all respect as desired by engineer at site.

Making Reniforced Cement Concrete Foundation of size 5000mmX2500mmX650mm for DG set 320 KVA with AMF Panel Foundation with 200mm below ground level and 450mm above ground level. The foundation includes Earth work in excavation in foundations trenches etc., Cement Concrete 1:4:8 with stone ballast, Shuttering for faces of concrete fouundations and foundations beam & plinth beam, Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator, Cold twisted deformed (Ribbed/tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works including bending and placing in position complete and finished with 12.5 mm thick cement plaster 1:5. Includes also Bolt and nuts of all sizes and length required and Cost of Shed with angle iron / MS Channel & Fiber sheet completer in all respect as per site requirement to cover the DG Set

Supply of Diesel to Start and Testing of DG Set

Providing VCB (1No Incomer and 2No Outgoing) At HT Incomer Room For Tata Memorial Cancer Hospital and HT Cable from HT Incomer Room to VCB Room

XLPE INSULATED HT CABLES:

XLPE INSULATED HT ARMOURED CABLES (LOOSE):

Supply & laying of Circular Aluminium Conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FR PVC inner sheathed, galvanized steel strip armoured and overall FR PVC sheathed cable confirming to IS:7098 (Part-2), 2011 working voltage 11KV(E) grade to be laid loose in the existing trench or pipe:-

HT Cable Overall size 240sq.mm (3Core)

S/E of Heat shrinkable cable end termination/ Straight through joint kit for 11 KVA /6.6 KV (E) XLPE Cables as approved & desired by Enginer in charge:-

Heat Shrinkable End Termination for cable size 240-400 sq. mm, 3Core (Indoor Type)

Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-

Brass Gland for Aluminium cable 3/3½/4 Core size 240sq.mm

PCC POLES:

Supply and erection of pre-stressed cement concrete pole of suitable length with a given planting depth confirming to IS-1678/ 1960/1978 below ground level in excavated pit of suitable dimensions complete in all respect as approved by Engineer-in-charge at site:-

PCC Pole Overall Length 9 metre, Planting depth 1.5 metre, W/L 200 kg.

JUMPERS FOR OVERHAED LINES:

Supply stringing and sagging of aluminium conductor steel reinforced (ACSR) on poles including binding with insulators using aluminium wires complete as desired by the Engineer in charge of the site:-

ACSR-WEASEL conductor (30 sq. mm) Size (6/2.55 Al.+1/2.55mm GI)

HT & LT LINE ITEMS:

Supply & erection of 'V' shape cross arm of MS channel 75mm x 40mm as per standard drawing. The item include supply and erection of half clamp made out of 50mm x 6mm flat including cost of nut and bolts as approved by Engineer-in-charge.

Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS 458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed. The pipes shall rest on the beds at all joints through their lengths and fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc.

R.C.C. Pipe NP -3

200mm i/d pipe

COPPER EARTHING:

COPPER EARTHING (Upto 14 metre in Length):

Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-

Earthing with 40mm x 5mm Copper Tape (upto 14Metre in Length)

COPPER EARTHING STRIP (As Additional Length):

Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty material as required etc.:-

Additional Length 40mm x 5mm thick Copper Tape

Supply, Erection, Testing and Commisioning of OEM Designed HT panel 12kV, 3Phase, 50Hz, Indoor metal clad, floor mounted, ‘Horizontal draw out’ type Extenable 3 no's VCB (Vacuum Circuit Breaker) switch board unit 1250 Amp. Extendable type which includes 1250 Amp. Vacuum Circuit Breaker for 1 no. Incoming and 2 no. Out goings VCB 1250Amp. 'Horizontal draw out’ type VCB (Vacuum Circuit Breaker) Out going feeder with Electrolytic Copper bus bars of suitable rating, Horizontal Isolation type as per IEC 62271-100-200. The Switchgear panels shall be sheet steel construction with not less than 2.5mm thickness for load bearing sections and not less than 2mm thickness for non-load bearing, dust, moisture and vermin proof to provide a degree of protection IP-4X in accordance with IS:13947. VCBs are type tested according to International Standards IEC-62271 at renowned laboratories. They are compact, safe and reliable. The Panels shall be tested for IAC level of Min. 21kA/1 Sec. No. of operations of Vacuum interrupter bottles for better performance (i) At rated current: 10,000 operation (ii) No. of short circuit dead operation at rated short circuit current: 100 opeartion

VCB parameters are as below: (a). Rated Voltage: 12kV (b). Rated short circuit breaking current withstand : Min. 25kA for 3sec. (c). Rated insulation voltage lightning (Impulse withstand) : At 75kV Peak (d). Rated insulation voltage( Power frequency withstand) : Min. 28kV (e). Rated operating sequence : O-0.3 sec - CO - 3 min-CO (f). Spring charging mechanism : Manually as well as motor operated (230V, AC, 50Hz) (g). Operation type: Manually and electrically open (Electrical-230V, AC,50Hz) VCB incorporating mechanical as well as electrical ON/OFF indiaction "OFF" push button, test/ serviceposition limit switches, with minimum 6NO+6NC breaker auxiliary contacts in service position, Manual charging of breaker should be done without opening the front door. Incomer shall consist of: (a). Cast Resin CT's 11kV : 600-300/1-1A, Core1: Class1, 10VA for 3phase, Core2: 5P10, 10VA (b). Cast Resin PT's 11kV : PT Ratio 11kV/√3 / 110V/√3 / 110V/√3, Class 1, Class 0.5 Burden 50VA

OEM Designed HT panel 12kV, 3Phase, 50Hz, Indoor metal clad, floor mounted, ‘Horizontal draw out’ type Extenable 3 no's VCB (Vacuum Circuit Breaker) switch board unit 1250 Amp. Extendable type which includes 1250 Amp. Vacuum Circuit Breaker for 1 no. Incoming and 2 no. Out goings VCB 1250Amp complete in all respects as approved and desired by the Engineer-in-charge at site. Besides this the manufactures should have NABL accredited labortary.

Providing HT Cable from VCB Room to PET-CY/SPECT-CT Building

XLPE INSULATED HT CABLES:

XLPE INSULATED HT ARMOURED CABLES (LOOSE):

Supply & laying of Circular Aluminium Conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FR PVC inner sheathed, galvanized steel strip armoured and overall FR PVC sheathed cable confirming to IS:7098 (Part-2), 2011 working voltage 11KV(E) grade to be laid loose in the existing trench or pipe:-

HT Cable Overall size 95sq.mm (3Core)

Providing, lowering in trenches to correct gradient and alignment, jointing with tyton rubber joint and cutting of reinforced cement concrete spigot and socketed pipes and specials with rubber ring ISI marekd as per IS code IS 458-2003 into trenches for all depths and laying out the same to correct alignment, gradients, levels etc. cutting of concrete beds and joints holes, supporting the pipes and specials in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benchings, haunches and envelopes are completed. The pipes shall rest on the beds at all joints through their lengths and fixing of rubber ring, facing, testing the pipes for leakage and making good the same leakage and all defects to the entire satisfaction of the Engineer-in-charge including all cartage etc.

R.C.C. Pipe NP -3

150mm i/d pipe

S/E of Heat shrinkable cable end termination/ Straight through joint kit for 11 KVA /6.6 KV (E) XLPE Cables as approved & desired by Enginer in charge:-

Heat Shrinkable End Termination for cable size 50-95 sq. mm, 3Core (Indoor Type)

PCC POLES:

Supply and erection of pre-stressed cement concrete pole of suitable length with a given planting depth confirming to IS-1678/ 1960/1978 below ground level in excavated pit of suitable dimensions complete in all respect as approved by Engineer-in-charge at site:-

PCC Pole Overall Length 9 metre, Planting depth 1.5 metre, W/L 200 kg.

JUMPERS FOR OVERHAED LINES:

Supply stringing and sagging of aluminium conductor steel reinforced (ACSR) on poles including binding with insulators using aluminium wires complete as desired by the Engineer in charge of the site:-

ACSR-WEASEL conductor (30 sq. mm) Size (6/2.55 Al.+1/2.55mm GI)

HT & LT LINE ITEMS:

Supply & erection of 'V' shape cross arm of MS channel 75mm x 40mm as per standard drawing. The item include supply and erection of half clamp made out of 50mm x 6mm flat including cost of nut and bolts as approved by Engineer-in-charge.

Providing PA System & Nurse Call System/ Emergency Bell's

PVC, HDPE PIPES & PVC FLEXIBLE PIPES:

Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-

Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface)

Supply and erection of CAT 6 with 23AWG solid bare copper conductor, special grade PE insulation with star separator, 4pair Unshielded Twisted Pair (UTP) industrial cable, FR PVC sheathed, Class-E, 250 MHz of bandwidth, supporting data transfer speeds of up to 10 Gbps (10GBASE-T) for distances up to approximately 180 feet, cables are manufactured and tested to meet the ANSI/TIA 568-C.2 and ISO/IEC 11801 Class E standards left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Supply & erection of CAT6 UTP Networking Cable 4 pair support up to 10/100/1000Mbps speed in existing PVC conduit including warrenty and service for one years complete in all respect as desired by the engineer in charge at site.

Supply & erection of Advanced PA Amplifier with Built-in Digital Player System comprises of following features:- = 220V AC & 12V DC operation = 75 watt PA Amplifier = 3 Mic & 2 Aux input = MP3 Recorder & player = USB & Card Reader = Remote control = Intelligent sound reinforcement = Speaker output @ 4Ω 8 Ω & 70V /100V = Active Bass & Treble Control = LED Display with Multimedia control = 1 Year onsite warranty including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Wall mounting column speaker 10W/100V including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of 18” Gooseneck Microphone with stand having on/off switch and 10 meter long Twin core shielded low noise with XLR connector including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Superior quality 2 core 0.75sqmm copper conductor Speaker wire. Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of PA cum Talk Back system comprises of following features:- Intelligent sound reinforcement 8 Zone LED Indicator Call all Zone feature Speaker output @ 4Ω 8 Ω & 70V /100V 1 Year onsite warranty including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Talk Back Unit PUSH TO TALK Switch, Speaker, Box Type speaker including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Nurse Station Unit For MAX 08 Beds including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Electronic Calling Unit including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Door Indicator including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Supply & erection of Controller PIH8 including warrenty and service for one years Complete in all respect as desired by the Engineer in charge of work at site.

Providing Advance Lightning Protection System:

Supply, erection, testing & commisioning of Early Streamer Emission (ESE) type Lightning Protection Complete with Lightning Air Terminal. The System should be corrosion resistant stainless steel chrome body capable of working in hazardous atmosphere and protecting against direct Lightning point as well conducting /diverting it to earth completely after tracing the Lightning in advance. As per NF C 17-102:2011 the air terminal should be tested for Lightning impulse current (10/350 micro sec) =100 KA and for local certification the air terminal should be tested for switching impulse current of 40 KA (8/20 micro sec) as per CPRI with 5 positive and 5 negative impulse. The ESE Terminals shall offer a protection radius of 79mtr., Level-1 High Protection and preferably to be mounted on roof top and center of the building / blocks with the highly insulated polyplastic adaptor with the Mast. (Its working principle evolves from local electrostatic field that develops naturally around the system as a thunderstorm begins to gather. In the event of descending lightning, an inbuilt triggering device generates high tension pulses at the conductor tip, causing a 'corona effect'.) Protection radius of 79Mtr at level 1 & 107 Mtr at level 4

Supply and fixing of GI Mast 5 mtr. height along with suitable base plate for mounting the terminal along with highly insulated adopter to mount ESE Air Terminal with the Mast. The Adapter shall have suitable Metal connector/Connecting point in such a way the top portion shall be electrically connected to the central tip of the ESE terminal and bottom portion connected to the down conducto, stray wires along with support shall be securely fixed with base plate and gauge wires where ever required.

Supply and installation of Lightning Strike Counter (6 digit display) of non-resettable (electromechanical) type which allows the automatic counting of the strikes received by the lightning protection system. This information is used to enhance lightning protection security & increase the effectiveness of inspection & maintenance procedures. It should be in IP-65 enclosure with minimum sensitivity of 1KA and maximum capacity 100KA. No external power source is required. It should be installed always 2 mtrs. above the ground level.

Supply, installation & testing of chemical earthing (Maintenance Free Earthing) system with UL approved copper bonded rod and exothermically welded copper busbar both tested by CPRI at 50kA Fault Current. A copper bonded steel rod shall have 3000 mm length and 17.2 mm dia. with copper coating thickness of minimum 250 microns. Along with earth enhancement compound tested by ROHS complying IEC 62561-7 in a sealed bag of minimum 50 kg (25 kg Bag x 2). A copper clad steel solid ground wire of 8 mm dia. for interconnecting earth pits. Each earth pit shall be covered with heavy duty weather proof environment friendly polyplastic earth pit chamber. The grounding minerals should not be pollute the ground water. The grounding minerals shall be tested & certified for the resistivity of less than 0.12 ohm-mtr.complete in all respects as approved and desired by the Engineer-in-charge of the work.

Supply & erection of Test Link of non-corroding, weather proof, water proof polycarbonate IP 65/55 enclosure including providing of 2 Nos. of insulated supports with suitable holes prefitted nuts & bolts to fix the down conductor & earth wire. The transparent cover fitted at approximately 500-1000mm from ground level shall be provided on each down conductor. complete in all respects as approved and desired by the Engineer-in-charge of the work.

Cost of Pole Foundation with earth work in excavation in foundations trenches etc. 0.25 meter below ground level, Cement Concrete 1:4:8 with stone ballast, Reinforced cement concrete M-20, Cold twisted deformed (Ribbed/ tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008 complete in all respect as desired by engineer in charge.

PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-

Overall size 70sq.mm (Un-sheathed) (Conducter connected the air terminal to earthing)

Providing Digital IP-PBX System in TMC, Civil Hospital Sangrur.

Supply& erection of Operator-cum-maintenance console with Large Backlit Display, 16 Direct Dialling Keys, HD sound quality, Duplex Speaker Phone, Touch sense keys, Polyphonic Ringtone, Full Duplex Speaker Phone, Hold, Conference, Redial, Transfer, MessageWait Lamp, Ringer Lamp, 49 keys including 4 Context Sensitive Hard Keys , 1 x RJ9 Handset Port, 240*64 Pixels Graphical LCD with Backlit , LED for Incoming/Ongoing Calls, Mute, Hold , Intuitive User Interface with Icons , Multiple Languages Caller ID with Name, Number, Room Monitoring, Operating Temperature Range = 0 to 45°C including all features listed in Product Boucher complete in all respect as desired by the engineer in charge at site.

Supply& erection of 32 Key DSS for operator console having 2 no. connection port to connect with operator console , LED indicator for each key, Room Monitoring, Space for name against each key, Operating Temperature Range = 0 to 45°C including all features listed in Product Boucher complete in all respect as desired by the engineer in charge at site.

Supply& erection of DC 48V Power Supply with minimum 30 Min. power back up (Batteries included). complete in all respect as desired by the engineer in charge at site.

Supply & erection of 500 Pair MDF and 500 Pair IDF with original Krone modules , lock and key facility, Metal Body. complete in all respect as desired by the engineer in charge at site.

Supply & erection of 100 Pair MDF and 100 Pair IDF with original Krone modules , lock and key facility, Metal Body complete in all respect as desired by the engineer in charge at site.

Supply & erection of 50 Pair MDF and 50 Pair IDF with original Krone modules , lock and key facility, Metal Body complete in all respect as desired by the engineer in charge at site.

Supply & erection of 24U Floor mount 19’’ Rack with glass door, lock & key facility 450mm-550mm depth with CPD, Cable Manager & Fan, Wheels. Complete in all respect as desired by the Engineer in charge of work at site. complete in all respect as desired by the engineer in charge at site.

Supply and erection 02 Pair 0.5mm PVC Dual sheathed Telephone Cable as per ITD Specification with Up to amendments complete in all respect as desired by the engineer in charge at site.

Supply and erection 10 Pair 0.5mm PVC Dual sheathed Telephone Cable as per ITD Specification with Up to amendments.complete in all respect as desired by the engineer in charge at site.

Supply and erection 20 Pair 0.5mm PIJF UN- Armoured Telephone Cable manufactured as per ITD Specification with Up to amendments complete in all respect as desired by the engineer in charge at site.

Supply and erection 50 Pair 0.5mm PIJF UN- Armoured Telephone Cable manufactured as per ITD Specification with Up to amendments complete in all respect as desired by the engineer in charge at site.

Supply & erection of 25 mm ISI marked PVC channel on wall surface. complete in all respect as desired by the engineer in charge at site.

Supply & erection of 45mm x 45 mm Cable Management Tray slotted Gray Colour ISI marked PVC on wall surface. complete in all respect as desired by the engineer in charge at site.

Supply & erection of Basic Featured Wired Telephone with Backlit Display, Redial, CLIP,& Mute Compatible with EPABX System Without Addition Programming.complete in all respect as desired by the engineer in charge at site.

Supply & erection of Featured Wired Telephone withLarge Backlit Display, Redial, CLIP, 2 Way Speaker, calculator, alarm, memory dial& Mute Compatible with EPABX System Without Addition Programming. complete in all respect as desired by the engineer in charge at site.

Supply& erection of Digital Hybrid IP-EPABX Configured for 02 no. SMPS Power Supply, 08 Trunk Ports, 08 Digital Extn Ports, 00 GSM Trunk Ports, 02 PRI of 32 Channels,5 IP Phone Extension, 20 channel Voice Mail with required hardware, 20 Channel IP decoder with required hardware, 320 Normal Extensions Ports and Expendable to 512 TDM Ports & 2000 IP Extensions. With following features:- Type of Switching IP at Core Processor Speed 900 MHz Dual Core,Slots Type Universal Made and make in India VOIP Protocols- SIP v2, SIP over TCP, Symmetric RTP, RTCP, 100rel/PRACK Network Protocol IPv6, IPv4, TCP, UDP, SNTP, STUN, ARP, ICMP, PPP, DNS, SMTP CO Trunk- Type Expansion Card for CO/FCO Interface Signalling Loop Start Loop Limit 1200Ω Off Hook AC Impedance 600/900/Complex Pulse Dialling 10/20PPS DTMF Dialling and Reception ITU-T Q.23 & Q.24 Return Loss >18dB Longitudinal Balance >50dB Transmission Level Adjust Tx Gain: -15dB to +10 dB, Rx Gain: -15dB to +10dB CLI Reception DTMF, FSK ITU-T V.23 and FSK Bell core 202 Call Maturity Delay and Polarity Reversal Protection Over Voltage and Over Current Secondary Protection Physical Connector RJ45 Digital Extension Type Expansion Card for Digital Key Phone Ports Signalling Proprietary Digital (2B + D) Interface Single pair for Speech, Signalling and Power Loop Limit 100Ω Speech Level Adjustable Tx and Rx Gain for Handset and Hands-Free Protection Over Voltage Secondary Protection Physical Connector RJ45 SLT(Normal Extension)-

Type Expansion Card for Analog Extensions Signaling Loop Start Dialing DTMF and Pulse (10/20PPS) Off Hook AC Impedance 600/900/Complex Off Hook Current 39mA Max Loop Limit 1800Ω Max (Excluding Telephone) On-Hook Voltage (Tip/Ring) -48V Nominal DTMF Detection ITU-T Q.24 Return Loss >18dB Longitudinal Balance >50dB Transmission Level Adjust Tx Gain: -3dB to +6dB, Rx Gain: -3dB to +6dB Ringing Trapezoidal 60VRMS/25Hz and Sinusoidal 52VRMS/25Hz REN 3 CLI Presentation DTMF, FSK ITU-T V.23 and FSK Bellcore 202 Protection Over Voltage Secondary Protection Physical Connector RJ45 Radio Link Support- Type Expansion Card for Radio Interface Line Inputs Balanced, Transformer Isolated 1Vrms, 600 Ω Line Outputs Balanced, Transformer Isolated 1Vrms, 600 Ω PTT Output Opto-Isolated Normally OPEN, 1A max Physical Connector Centronix

RS232c (COM) Ports - 1 No. USB Ports - 1 No. Group Conference (3-Party) - 15 No. Auto-Attendant, Voice Help, Voice Tones Voice Messages (16 seconds each) Ethernet Ports (Gigabit) - 02 No. Universal Slots - 16 no. Support Single Line Analog Telephones Connectivity:- Proprietary Digital Key

GSM/3G/4G Network Two wire Trunk T1/P1/PRI IP Users Sip Trunks Radio Interface Ports E&M Ports DC Power Supply Redundant SMPS 2 No. inbuilt SMPS Power Supply 48V DC. complete in all respect as desired by the engineer in charge at site.

Please Enable Macros to View BoQ information