NIT NO: 1020/TC/25-26

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming toIS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: Cement Mortar 1:4 (1 cement : 4 coarse sand)

Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level:

Extra for providing and placing in position hopping 25x1.60 mm or 2 Nos 6mm dia MS bars reinforcement at every third course of half brick masonry.

Providing and making 6mm thick cement plaster of mix: In Cement mortar 1:3 (1 cement : 3 fine sand)

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:6 (1 cement : 6 fine sand)

In cement Mortar 1:3 (1 cement : 3 fine sand)

15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:6 (1 cement : 6 fine sand)

Providing and fixing chicken mesh weighting notless than 250 gms/sqm as per IS: specification in the required width with 40mmlong steel nails on vertical and horizontal surface near R.C.C. And bricks walls junctions including scaffolding and all lead and lift etc. complete before plastering uptp 10 mts in height.

Providing and applying Polymaric cement primer on all surface applied @ 0.80 ltr/ 10 sqm as per relevant I.S Code 15489: 1974 ( Product such as Birla white prime coat/ activcoat, Asian Trucare, Dulux Interior cement primer, Opus Calista/110) with all tool tackles and labour etc. complete for the work.

Providing and applying plaster of paris putty over plastered walll surface including scaffolding complete upto 2mm thickness to make surface even and smooth in line and level

Providing and applying Premium Plastic emulsion paint with roller application minimum three coats applied @ 0.75 litr/10sqm up to final finish as per relevant I.S. Code 15489:2013 Type-1 Class D & C ( Glossy and semi Glossy Finish) of required shade( Product such as Asian Apcolite Premium, Dulux Super Cover, Berger Easy Clean, Nippon Breezee Metex Gold, Opus 1-50/ Calista) Inclusive of Providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. ( With 3 Years Warranty)

Providing and Applying on exterior surface with PREMIUM Exterior Emulsion Paint of required shades to give protective and water proof finish minimum three coats applied @ 1.40 lit/10 sqm up to final finish as per relevant I.S. Code 15489:2013 Type-2 Class D,C (Glossy/semi Glossy finish) Product such as Asian Apex, Dulux Weather Shield Prime E900 , Berger Weathercoat Antidust, Nerolac Everlas Excel, Nippon sumo Etra, Opus True Flex) Inclusive of Providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work. ( With 3 Years Warranty)

Providing and applying Glossy Finish Enamel Paint minimum 2 coats in all surface applying @ 0.75 litr/10sqm up to required finish as per relevant I.S. Code 2932:2013 of ( Product such as Asian Apcolite Premium Enamel, Dulux Promise Premium Enamel , Nerolac Synthatic Enamel, Opus Prime Enamel) Inclusive of Providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.

Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including priming coat with epoxy primer, preparation of surface, etc. complete.

Providing and laying Melamine polish on new wood work (two or more coats) with spray machine after preparing surface by rubbing down smooth with sand paperspreparations of surface applying 5 to 10 coats French sprit polish applying two coats of Melamine sealer and finally applying two coats of Melamine cleaas per manufacturers specifications complete:

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tile including cleaning of joint etc complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Dark shade using ordinary cement

Providing and laying double/ multi charge/ multi charge (minimum 2.0 m thick layer) vitrified floor tile with water absorption less than 0.05% and conforming to IS : 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

Providing and laying vitrified floor tiles with soluble salt printing, of size 600x600mm with water absorption less than 0.5% and conforming to IS : 15622 of approved make, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including routing the joints with white cement and matching pigments etc. complete.

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone grey/pink

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer..

Providing and fixing steel door/ window with M.S. sheet 1mm thick, frame of angle iron, diagonal braces of angle/ flat iron of suitable size, 3.00 mm M.S. gusset plates at junctions and corners, all necessary fittings complete including applying a priming coat of red oxide zinc chromate primer.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rails of T-iron 40x40x6mm with 38mm steel pulleys complete with bolts, nuts, locking arrangement stoppers, handles including applying a priming coat of red oxide zinc chromate primer.

Supplying and fixing rolling shutter of approved makes made of M.S. laths interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and out side locking with push and pull arrangement complete but excluding the cost of top cover and spring. 80x1.20mm M.S. Laths

Providing and fixing 27.5cm long wire spring for rolling shutters.

Providing and fixing M.S. sheet top cover for rolling shutter 1.25mm thick

Providing and fixing ball bearing for rolling shutters.

Providing and fixing mechanical device chain and crank operation for operating rolling shutters.

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing and panelling to be paid for separately For fixed portion

For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4 mm thickness

With float glass panes of 5 mm thickness

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 304

KOTA stone slab 25mm thick in risers and treads of steps, skirting dado and pillar laid in 12mm (Average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (single stone is to be used for riser and treads of steps and the width of stone for skirting and dado shall be equal to the height of skirting/ dado up to length of 1.0 M.)

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm) finished with a floating coat of neat cement. 50 mm thick

Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg/ sqm for receiving cement concrete floor including roughening cleaning etc complete.

Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equivalent), on aluminium sections for fixing aluminium/ glass panel, sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete.

Providing and fixing aluminium composite panels in approved panel sizes,thickness and shape on aluminium frame work on face of building. (Frame to be paid separately) 4mm thick

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) 1st layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. ii) 2nd layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. iii) 3rdlayer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with coarse sand @ 1.289 kg/sqm and water proofing cement compound @ 0.07 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around. iv) 4th and final layer of brick tiling with cement mortar (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC, kitchen and the like consisting of: i) 1st course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 including rounding off junction of vertical and horizontal surface. ii) 2nd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound including rounding off junction of vertical and horizontal surface. iii) 3rd course of applying blown or residual bitumen applied hot @ 1.7 Kg. per sqm of area. iv) 4th course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg. per sqm of area.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size).

Providing and mixing in cement mortar, triangular polyester fiber Recron 3s (Anti-shrinkage Admixture) of 6 mm length of approved make like Reliance industries Ltd etc. in proportion as recommended by manufacturer.

Providing and fixing 15 mm nominal bore uplasticised PVC connection pipe with PTMT nuts and PVC bush of approved quality and colour: 45 CM length

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete. 75 mm dia pipe.

110 mm dia pipe.

150 mm dia pipe

Providing and fixing UV stabilized Unplasticised -PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/Tee with door/Bend 45˚/Bend 90˚ 75 mm

Double Y with or without door 75 mm

Vent covel 110 mm

P trap 110mmx110mm long

Nahani trap 110x75mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia

Providing and fixing on wall surface G.I. pipes medium class complete with G.I. fittings and clamps, including cutting, making good the walls etc. and testing of joints complete: 15 mm dia. nominal bore

20 mm dia. nominal bore

25 mm dia. nominal bore

40 mm dia. nominal bore

Providing and fixing concealed in wall G.I. pipes medium class complete with G.I. fittings and clamps, including painting with anti corrosive bitumastic paint, cutting chases, making good the walls etc. and testing of joints complete: 15 mm dia nominal bore

20 mm dia nominal bore

Providing and laying in trenches G.I. pipes medium class complete with G.I. fittings including excavation of trenches, refilling the same and testing of joints complete: 50 mm dia. nominal bore

Providing and fixing G.I. Union in G.I. pipe (New work) including cutting and threading the pipe and making long screws etc. complete: 15 mm nominal bore

20 mm nominal bore

25 mm nominal bore

50 mm nominal bore

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bib cock (400gms)

Bottle trap set with extension pipes

Shower rose (revolving type) (150mm)

Towel ring (150 mm dia))

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing brass/gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore

50 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

25 mm nominal bore

Providing and placing on terrace (at all levels) polyethylene water storage tank ISI marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing 600x450 mm beveled edge 4mm mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 5mm thick mirror

Providing, laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design: 150 mm diameter S.W. Pipe

Constructing brick masonry manhole with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Providing and constructing brick masonry chamber for underground pipe and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm² in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :

Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Providing and fixing square-mouth S.W. gully trap grade 'A' complete with C.I. grating brick masonry chamber with well burnt modular clay bricks crushing strength not less than 35kg/cm2, water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 180x150 mm size P type

Providing & fixing Jaquar make anti germ Flucro Polymer Coated squatting pan (Indian type Orissa pan W.C.260x440x580 pan) with 100mm VARIO BEND Sand P.V.C.P. and S trap, with open slim wall hung cistem code (WHT-184) capacity 3 litre/6 litre with required finish wall and floors wherever required:

Providing & fixing Jaquar make vitreous china pedestal type Anti germ Fluoro Polymer coated ground moulded EUROPEAN type w.c. Pan Size 785x370x645mm CODE SLS 0916 BS- & and 7.2 litre low level slim dual flush PP (polypropeline) made 80 mm thick concealled flushing cistren & SOFT CLOSING SEAT COVER CODE ZPS 1019 making good wall and floors wherever required:

Providing & fixing Jaquar make vitreous china pedestal type Anti germ Fluoro Polymer coated mounted EUROPEAN type w.c. Pan Size 760x365x620mm system CODE CNS WH 16 with soft closing seat cover CODE WCS-7 and 7.2 litre low level slim dual flush of coad CNS WCF 01 PP (poly propeline) made 80 mm thick concealled flushing cistren, flushing capacity CODE WHC-WCF1 and making good wall and floors wherever required:

Providing & fixing Jaquar make white vitreous china Anti germ Fluoro Polymer coated under counter Wash Basin Size 190x550x435mm with C.I. Brakets, 15mm C.P. 32 mm C.P. brass made waste Trap size 200 x 300 mm fitting and wast coupling and bottle trap code ALD 769 L 250 x 190 fixures complete including painting of fitting and cutting and making goor the wall and floors wherever required. coad CNS WCF 01 PP (poly propeline) made 80 mm thick concealled flushing cistren, flushing capacity CODE WHC-WCF1 and making good wall and floors wherever required:

Providing & fixing Jaquar make white vitreous flat back Anti germ Fluoro Polymer coated urinal Size 630x375x315mmcode URS-WHT-0702N with FLUSH PLATE PRS-CHR 073 with brass made prematic flush valve with wal flush (decol technology 400000 operation) and also included waste pipe and coupling complete with fitting and bracket cuttin and making good wall.

Providing & fixing Jaquar make 8 mm thick froasted urinal glass partition size Hght 900x450mm brass made bracket with chrome plating.

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 auto closing soft touch Item code : CHR-011, CONNECTION PIPE, ALD CHR-801B

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 auto Pressmatic pillar cock auto closing system item code : PRS-031 & ALD-CHR-801 B Item code : CHR-011, CONNECTION PIPE, ALD CHR-801B

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Quarter turn Pillar Cock Item Code : ARI-CHR-39011

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron BIB cock two way with health faucet. Item code : ARI-39041, ALD-CHR-583

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron Concelled stop cock Item code : ARI-CHR-39083K

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron Angular stop cock Itqm code : ARI-CHR-39119

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron Wall Mixture Itqm code : ARI-CHR-39053

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron basin Mixture Itqm code : ARI-CHR-39001B

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron sink cock Itqm code : ARI-CHR-39347

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron sink mixer Itqm code : ARI-CHR-39309

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Microns soap dispenser with glass bottle item code : AKP-35753P

Providing & fixing Jaquar make in position best indian bonut size 24 mm ceramic disc size 19mm and minimum body thickness 2mm nickle plating. 1 micron and crome plating 0.3 Micron toilet roll holder with flap. item code : AKP-35753P

Supplying,assembling,lowering and fixing in vertical position in bore well ISI marked G.I. Casing pipe (Plain) medium class in 4 to 7 meters length one end fitted with socket as per IS:1239 (Part-1& Part-2)1992 with Ivth revision (Up-to-date amendments) of reputed & approved make including required hire & labour charges fittings & accessories all complete for all depths as per direction of Engineer-in-charge. 150 mm nominal dia

Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800 (part 1) including collecting samples from different strata preparing and submitting strata chart/bore log including hire & running charges of all eqipments tools plants & machineries required for the job all complete as per direction of Engineer-in-charge upto 90 metre depth below ground level. All types of soil. 150 mm dia

Rocky strata with boulder 150 mm dia

Boring/drilling bore well perfectly vertical for the specified depth suitable to receive required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800 (part 1) including collecting samples from different strata preparing and submitting strata chart/bore log including hire & running charges of all eqipments tools plants & machineries required for the job all complete as per direction of Engineer-in-charge beyond 90 metre & upto 150 metre depth below ground level. Rocky strata includings boulder 150 mm dia

Providing and fixing suitable size threaded mild steel l cap or spot welded plate to the top of bore well housing/casing pipe removal as per requirement all complete for bore well of: 150mm dia

Providing and fixing on wall surface G.I. pipes medium class complete with G.I. fittings and clamps, including cutting, making good the walls etc. and testing of joints complete: 50 mm dia. nominal bore

Supply, erection, jointing, testing & commissioning of C Class MS pipes (as per IS: 1239) including necessary specials such as tees, bends,flanges reducers etc., complete on wall/ eiling. The pipes to be erected on wall or suspended from beams, RCC roof slabs with suitable size MSbars/ angle irons including painting of metal part except pipe line. 50mm dia.

65mm dia.

80mm dia.

100mm dia.

150mm dia.

Painting for M.S. pipe with a coat of ed oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 50mm dia.

65mm dia.

80mm dia.

100mm dia.

150mm dia.

Providing and wrapping 4 mm thick of approved make and quality bitumen based anti rust felt over MS pipe with overlap of 25 mm to make an impermeable layer including painting with one coat of bitumastic paint before felt complete. (Only on MS pipe to be laid in soil below ground). 80mm dia.

150mm dia.

Providing, installation, testing and commissioning of dual plate non- turn valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required. 100mm dia.

150mm dia.

Supplying, fixing, testing and ommissioning of flanged butterfly valve PN 1.6, with Bronze/Gunmetal seat duly ISI marked complete with Nuts, Bolts, washers, gaskets, conforming to IS: 13095 of following sizes as required. 80mm dia.

150mm dia.

Providing and fixing C.I. double flanged sluice valves rated to PN 1.6 with C.I. Wheel bolts, nuts, washers 3mm thick insertion rubber gasket including matching flanges table E, complete. 100mm dia.

150mm dia.

Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 25 mm dia

Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia and with necessary G.I. coupling, valve to be fitted on top of Air vessel or on wet riser as per specification.

Providing and fixing pressure switch with suitable for 1-10 Kg/cm2 including 12/15 mm Ø isolation valve, G.I. nipple, elbow, electrical connections setting of Cut-In and cut-Off pressure complete in all respects and in an approved manner.

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-21 kg per cm square fitted with 12/15 mm Ø. pad cock valve, and G.I. pipe, elbow etc. as per requirement in approved manner.

Providing and fixing 15 mm dia, Quartzoid bulb type G.M. Sprinkler Head set to operate at 680C of approved make chrome plated complete in all respect as required.

Supplying and fixing swinging type First-Aid Hose Reel drum with MS construction spray painted in Post office Red colour, conforming to IS: 884 with upto date amendments, complete with brackets for fixing on wall, connections from riser with 25 mm dia MS/GI pipe and GM gate valve but excluding hose reel.

Supplying and fixing 19mm dia 22.5 metre long high pressure polypropylene First-Aid Hose Reel.

Supplying and fixing single headed internal hydrant valve with instantaneous Gun metal couplings of 63 mm dia with cast iron wheel ISI marked conforming to IS: 5290 (Type - A) with blank Gunmetal cap and chain as required.

Supplying and fixing 63 mm dia, 15 mtr long RRL hose pipe with 63 mm dia Male and Female Stainless Steel-IS: 3444 Grade-1 couplings duly binded with GI wire, rivets etc. conforming to IS: 636 (Type -A) as required.

Supplying & fixing 63 mm dia Stainless Steel IS: 3444 Grade-1 branch pipe with 20 mm dia (nominal internal) Gun Metal nozzle conforming to IS: 903, suitable for instantaneous coupling connection to connect hose pipe coupling as required.

Supplying and fixing of MS hose cabinet box of made of 2 mm thick MS sheet and 40 x 40 x 5mm angle iron with front openable cover having 6 mm thick glazed glass viewing window i/c necessary locking arrangement, on existing wall/ brick platform etc complete as required. 23.25.3) Size 600 mm x 600 mm x 500 mm

Supplying and fixing 2 way Fire Brigade Connection of cast iron body with 2 Nos. Gun metal male instantaneous inlet couplings complete with cap and chain conforming to IS: 904 including connection to existing MS pipe line complete as required.

Providing and fixing M.S. structural work fabricated from standard sections, (MS rounds, angles, channels etc.) including cutting to size, drilling welding including cost of steel fasteners, clamp in RCC structural members as directed, including two coat of enamel painting over one coat of red oxide primer complete.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Constructing masonry Chamber 60x45x50 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Supplying,assembling,lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) slotted pipes with ribs, confirming to IS: 12818 including hire & labour charges fittings & accessories etc. All complete for all depths as per direction of Engineer-in-charge. 150 mm nominal size dia.

Providing and fixing filter of minimum 100 litre capacity for roof top rain water harvesting through tube well consisting of two layered HDPE tank with five layers (each layers of minimum 100 mm) consist of coarse sand, 4mm, 6mm, 8mm & 12 mm gravels with stainless steel wire mesh fixed between each layer with suitable length and sufficient numbers of 110 mm dia PVC pipe pieces in the bottom of tank to support the above layer including fixing of inlet and out let P.V.C. pipe of required diameter upto 2 metre length on each side cement concrete platform of required size complete as directed by Engineer in charge.(excluding cost of tubewell and inlet and outlet pipe beyond 2 metre.)

Providing and fixing PVC ball valve for inlet/ outlet of rain water harvesting pipe and filter.

Excavation for all types and sizes of foundations, trenches and drains or for any other purpose including disposal of excavated stuff upto 1.5 m lift and lead upto 50m (at least 5m away from the excavated area), including dressing and leveling of pits. In all types of soils.

Extra for every additional lift of 1.5 m or part thereof. All types of soils

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Providing and laying nominal mix plain cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of form work. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Providing and laying nominal mix reinforced cement concrete with crushed stone aggregate using concrete mixer in all works upto plinth level excluding cost of form work. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size).

Providing and placing in position reinforcement for R.C.C. work including straightening, cutting, bending, binding etc. complete as per drawings including cost of binding wire in foundation and plinth all complete: Thermo-Mechanically treated bars FE 500D

Thermo-Mechanically treated bars FE 415

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Wall of any thickness including attached pilasters, buttresses etc. in super structure.

Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth leve

Columns, Pillars, Piers and likes- rectangular or square in shap

Beams, lintels, cantilevers & walls

Extra for providing and mixing water proofing materials in cement plaster work in proportion as recommended by manufacturer.

Neat Cement punning.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Brick work with modular well burnt (open bhatta) clay bricks of crushing strength not less than 20 kg/sqcm and water absorption not more than 25% in foundation and plinth in: Cement Mortar 1:6 (1 Cement : 6 Coarse Sand

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with a lead upto 50 M. and lift upto 1.5 M.

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Painting exterior surface with ACRYLIC SMOOTH exterior paint of required shade as per manufacturer's specifications to give protective and decorative finish including cleaning washing of surface etc. complete with: On new work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Structural steel work riveted or bolted or welded in built-up sections, trusses and frames work upto a height of 5m above plinth level, including cutting, hoisting, fixing in position and applying a priming coat of red oxide zinc chromate primer.

Painting on new work (two or more coats) to give an even shade with: Satin synthetic enamel paint

Providing and fixing concertina coil fencing with required dia 610 mm (having 50 nos. round per 6 metre length) up to 3m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete as per direction of Engineer-in charge with reinforced barbed tape (R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

(A) ELECTRIFICATION Wiring for light/ fan/ exhaust fan / call bell point with 1.5 sqmm FR PVC insulated stranded copper conductor single core cable in concealed PVC conduit, with 5 amp modular switch, modular base and cover plate, suitable size G.I. box and earthing the point with same size cable as required. 3.7.1 Short Point

Medium Point

Long Point

Wiring for twin control light point with 1.5 sqmm FR PVC insulated stranded copper conductor single core cable in concealed PVC conduit, with 5 amp modular switch, modular base and cover plate, suitable size G.I. box and earthing the point with same size cable as required.

Extra for providing and fixing light plug point on board in concealed PVC conduit point wiring with modular type 3 pin 5 amp socket outlet and 5 amp switch including cost of base and cover plate and G. I. box etc. as required.

Wiring for light plug point with 2x2.5 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. 3.10.3 Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 2x4 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. 3.11.3 Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for power plug point with 2x6 sq mm FR PVC insulated stranded copper conductor cable in concealed PVC conduit along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size cable etc. as required. 3.12.3 Long Point

Extra Long Point I

Extra Long Point II

Extra Long Point III

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in concealed PVC conduit as required. 3.13.1 3 X 1.5 sq. mm in 20mm conduit

3 X 2.5 sq. mm in 20mm conduit

6 X 2.5 sq. mm in 25mm conduit

9 X 2.5 sq. mm in 32mm conduit

12 X 2.5 sq. mm in 32mm conduit

3 X 4 sq. mm in 25mm conduit

6 X 10 sq. mm in 40mm conduit

6 X 16 sq. mm in 50mm conduit

4 X 25 sq. mm + 2 X 16 sq. mm in 50mm conduit

Supplying and fixing of following sizes PVC conduit along with accessories in surface complete as required. (For all Electrical nad Low Voltage) 4.15.1 20 mm

Supplying and fixing following modular switch, socket, other accessories on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 7.4.8 Fan regulator (two module size) electronic stepped type moving all rounds.

Telephone socket outlet

T.V. antenna socket outlet

Computer Outlet Jack

Batten/Angle Holder

25/32 amp A.C. Starter switch

Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts A.C. supply, complete as required. 7.7.2 Deluxe

Providing and fixing round/ hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook, 1.6mm thick MS sheet cover, in RCC slab etc. as required.

Providing and fixing fan clamp made of 3mm thick MS flat on existing iron trusses/ girder including necessary bolts and nuts etc. as required.

Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable, earthing etc. complete as required. 8.1.2 1200 mm sweep

Supplying and fixing of wall/ cabin fan of 400mm sweep including connection etc. as required.

Supplying, installation, testing and commissioning of 250/ 300 mm sweep 1400 rpm medium duty (continuous running) exhaust fan in existing opening in wall including earthing etc. complete as required.

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 watt {4 feet}

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as required and furnishing 2 Yrs Guarantee certificate from manufacturer. 8.20.2 9 Watt

Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as required and furnishing 2 Yrs Guarantee certificate from manufacturer. 8.21.2 36 watt, size 600 x 600mm

Supplying, fixing, testing and commissioning of following LED lamps with inbuilt electronic driver heat sink and all other accessories in existing holder/ luminaries as required and furnishing 2 Yrs Guarantee certificate from manufacturer . 8.22.5 12 Watt

SITC for LED 40w COB 3000K CCT

SITC for LED Strip Light 5Mtr 3000K 25/24w with LED Driver

SITC for LED FLOOD LIGHT 125W

Supplying , installation , testiing and commissioning of following type Recessed LED Step Lighting fixture with IP66/65 protected Die-Cast Aluminum housing and Heat resistive Toughened Glass. LED shall having LM80 complied as per L70 standard LEDs minimum tested for 10,000 burning hours with 3000K CCTwith minimum life cycle 50000 hrs burning hours at 50˚C. Luminaire LED should have secondary Optic lenses. Driver shall be 3 stage Constant Current Constant Voltage with voltage range of 150-270V AC. Output voltage of driver should be complied to Safety Extra Low Voltage norms not exceeding 60V DC. Driver Power factor shall be 0.95 and above and THD shall be less than 10%. 3 watt

Supplying, installation, testing and commissioning of following LED Rope light complete as per specification and IP65, P.F. should be greater than 0.75 9 Watt per Metre RGB

Supplying, installation, testing and commissioning of water proof Radio Frequency based RGB Controller for rope light with remote control IP 65 as per the specifications

Supplying, Installation, Testing & Commissioning ofAluminium Profile for for Lighting (including aluminium profile and acrylic cover excluding led strip light) having following sizes (WXH) : 35X25 mm Outer Dimensions

Providing and making interconnection in cubical panel between BBC and switchgears with following size aluminium strip of length upto 50cm as required (To be measured separately for each phase/ neutral). 9.16.1 20x5mm (100 amps)

30x5mm (200 amps)

50x6mm (400 amps)

100x6mm (800 amps)

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured ) 9.19.1 Upto 300 mm deep

Above 300 mm and upto 450 mm deep

Above 450 mm and upto 600 mm deep

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 11.1.1 3 pole MCCB, 25-63A, Fixed Thermal Release, 10KA

3 pole MCCB, 80-100A, Fixed Thermal Release, 10KA

3 pole MCCB, 100A, Adjustable Thermal - Magnetic Release, 25KA

3 pole MCCB, 125A, Adjustable Thermal - Magnetic Release, 25KA

3 pole MCCB, 200A, Adjustable Thermal - Magnetic Release, 35KA

3 pole MCCB, 250A, Adjustable Thermal - Magnetic Release, 35KA

4 pole MCCB, 630A, Adjustable Microprocessor Release, 50KA

Supplying and fixing on surface/ recess following way, 240 volts SP&N MCB distribution board consumer unit of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as required. (But without MCB/RCCB/Isolator) 11.3.4 2 + 16 way

Supplying and fixing on surface/ recess vertical type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, with 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland/ knock out plate, including interconnections, earthing etc. as required. (But without MCB/RCCB/Isolator) (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 11.5.4 4 way (4 + 12), Double door

8 way (4 + 24), Double door

12 way (4 + 36), Double door

Supplying and fixing on surface/ recess horizontal type following way, 415 volts, TPN MCB distribution board of sheet steel phosphatized and powder painted, complete with tinned copper busbar, neutral busbar, earth bar, din bar, detachable gland plate, including interconnections, earthing etc. as required. (But without MCB/RCCB/Isolator) 11.4.4 4 way Double door

6 way Double door

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required . 11.11.2 6 amps to 32 amps

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as required . 1.16.5 63 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 11.20.2 40 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required . 11.21.2 40 amps

Providing and fixing approved make, Manually Operated, draw out type, 415/500 volts, air circuit breaker complete with all standard accessories as per manufacturers specifications including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. 12.1.8 1250 amps, 4 pole, 50 KA

Providing and fixing metal clad, TP&N motorized change over switch unit, 415/500 volts, including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. 12.8.6 630 amps

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as required . 12.15.8 1000/5 amps

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as required.

Providing and fixing penal mounting following rating digital type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 12.19.5 0-1000 amps

Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required 12.20.2 Digital type

Supplying, installation, testing and commissioning following rating single phase in single phase out ON-LINE UPS including connection etc but without batteries as required 13.2.3 5 KVA with DC bus voltage 180 V

Supplying, installation, testing and commissioning following rating SMF (Sealed Maintenance Free) lead acid battery including connection as required 13.4.4 120 AH

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required.

Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ concealed conduit/ submain wiring/ cable as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate having 4 nos holes for fixing etc. complete as required.

Making jointing of copper tape (with another copper tape, base of the finial or any other metallic object) by reverting, sweating and soldering/ nut bolting of as required.

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing copper tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick copper strip, 125 mm long, with 4 nos. of tinned brass bolts, nuts, chuck nuts and spring washers etc. complete as required.

CABLE- Supplying and laying following size RCC Hume pipe class NP-2 (in standard length of 2 metre) with collar in ground below road, path etc at a depth not less than 50 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.4.3 200 mm dia

300 mm dia

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 17.1.9 3 x 25 sq. mm

3.5 x 35 sq. mm.

3.5 x 50 sq. mm.

3.5 x 70 sq. mm.

3.5 x 300 sq. mm.

Supplying and making end termination with brass compression gland and copper lugs for following size armoured copper conductor power cable of 1.1 KV grade as required. 17.24.10 3 X 25 sq. mm (25 mm)

3½ X 35 sq. mm (28 mm)

3½ X 50 sq. mm (32 mm)

3½ X 70 sq. mm (35 mm)

Supplying and making outdoor end termination with cast resin compound including aluminum lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor power cable of 1.1 KV grade as required. 17.25.9 3½ X 300 sq. mm

Supplying and making outdoor end termination with cast resin compound including aluminum lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor power cable of 1.1 KV grade as required. 17.25.9 3½ X 300 sq. mm

Supplying and fixing of following sizes powder coated, perforated, M.S. cable trays bends (horizontal) turning at 900 in same plane with perforation not more than 17.5% rigidly jointed with cable tray etc. complete as required.20.1.2 150 mm width X 50 mm depth X 1.6 mm thickness 20.1.2 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

PUMP -Supplying, installation, testing and commissioning of submersible pump set for water supply system with submersible motor directly coupled to multi-stage submersible pump of specified discharge capacity, head, delivery size in existing bore well including 2 sets of suitable size holding clamps made out of 50 mm X 6 mm MS flat, connection with suitable submersible cable of standard length etc. as required. .26.3.2 1.5 HP, single phase

Supplying and fixing following dia HDPE pipe PE-80 Grade (8kg/sqcm) in single length in the suction/ delivery line of water supply pump etc. as required. 26.6.1 32 mm outer dia

Supplying and fixing of following sizes GM gate valve ISI mark in the suction/ delivery line etc. as required. 26.7.6 32 mm dia.

Supplying and fixing of following sizes GM non return valve ISI mark in the suction/ delivery line etc. as required . 26.8.6 32 mm dia.

Supply, installation, testing and commissioning of 1-3 HP 1 phase submersible motor starter cum control wall/ floor mounted type made out of not less than 1.6 mm thick MS sheet and comprising of following panel mounting switchgears there in including connection inter-connection etc. as required. a) Phase indicating lamps with fuses and toggle switches 1 set b) 1/2/3 HP 1 phase DOL starter with over load and no volt relay 1 No c) 25 A "C" curve DPMCB 1 No d) Voltmeter 0-250 V 1 set e) Ammeter 0-10 A 1 set

Supplying and fixing M.S. clamp 50 cm long made of 50mmx5mm thick M.S. Flat for holding the pipes and submerable pump set as required.

Supplying and making water proof joint with heat shrinkable joint kit including copper ferrules for following size of 3 core submersible copper conductor cable of 1.1 KV grade as required 26.15.2 3x2.5 sqmm

Supplying and laying of approved make stainless steel wire rope of 6 mm dia for support of submersible pump set complete with tying to pump set and pump holding clamp.

Supplying, installation, testing and commissiong of following size drinking water cooler storage type ISI marked, eco friendly non CFC refrigarant, water tank and cooler cabinet sheet material- stainless steel {grade AISI 304} with thickness>= 0.8 mm, with PUF insulation including all accessories connection etc complete as per specification. 60/120 Ltrs/hr

Supplying, installation, testing and commissiong of following capacity of RO purification system with UF/UV/TDS controler and UV lamp {IS 14724 Ultra voilet disinfection} and minimum three stage purification, automatic on/off, output water conferming standard IS 10500 with inbuild storage tank including all accessories connection etc complete as per specification. 50 Ltrs/hr output capacity

Supplying and drawing UTP 4 pair Cat 6 LAN cable in existing surface/ concealed steel/ PVC conduit as required.

(B) FIRE ALARAM Supply, installation, testing & commissioning of Networkable Intelligent Addressable Fire Alarm Control Panel (EN/UL Approved) having following no of loop, each loop capable of connecting upto 99 detector and 99 devices, with minimum 200 character LCD display, multiple access levels, event history file in non-volatile memory (EEPROM) to store 20000 events, including Loop driver cards, network card, in-built battery backup for 72 hrs in standby mode & 30 min in alarm condition mode in metal enclosure and other required accessories 29.1.3 1 Loop

Supply, installation, testing & commissioning of Networkable Intelligent Addressable additional one loop card in existing Fire Alarm Control Panel (EN/UL Approved) having provision of 10 loops.

Supply, installation, testing & commissioning of Networkable Intelligent Analogue Addressable Fire Alarm Active Repeater Panel with 40 characters LCD display metal enclosure & required accessories.

Supply, installation, testing & commissioning of follwing type Addressable detectors ((UL and FM approved)) with detector mounting base and other required accessories. Approved Make (CerberusPro-UL, Notifier, Detectomat, Autronica) .29.6.1 Photoelectric type Smoke detectors

Rate of Rise Thermal (Heat) detectors

Supply, installation, testing & commissioning of follwing Addressable devices (EN/UL approved) with mounting base and other required accessories. 29.7.2 Pull Station Type Manual Call Points.

Isolator module (Fault / Loop)

Control Module (for access triping off)

Response indicator

Supply, installation, testing & commissioning of Analogue Addressable BEAM TYPE FIRE detectors suitable for minimum 30m span with detector mounting base & required accessories.

Supply, installation, testing & commissioning of Strobe cum Sounder in ABS plastic body having sound adjustible Db level upto 90 dBs and a multi tone facility and light ajustable to 110 candelas complete with mounting base, enclosure & required accessories(UL and FM approved)Approved Make (CerberusPro-UL, Notifier, Detectomat, Autronica).

Supplying, installation, testing and commissioning following rating SMF (Sealed Maintenance Free) lead acid battery including connection as required 13.4.1. .45 AH

Supplying and fixing of following sizes steel conduit along with accessories in surface including painting complete as required. 2.15.1 20 mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ concealed, steel/ PVC conduit/ PVC casing caping as required . 5.11.2 2 x 1.5 sq. mm

2 x 2.5 sq. mm

Supply and erecting of following ISI marked Fire extenguishers on wall/ column including erecting bracket etc complete. ABC Fire Extinguisher 4KG Nitrogen Store Pressure As per IS: 15683:2018 Body Sheet Not Less Then 2mm Thickness, CE Mark NRV Valve With ABC Powder 90% UL 299 FIRE RATING: 2A, 89B. With all accessories.

CO2 type Fire Extinguisher ISI marked confirming to IS:15683:2018 Capacity 3Kg. INITIAL CHARGE:- Carbon dioxide used in extinguishers shall comply with IS 15222. FIRE RATING:- 34B. Complete with Hose Assembly and horn, locking arrangement, operation manual, bracket with two screw and sleeve

( C ) CCTV CAMERA:- Supply, Installation, Testing & Commissioning of 2C 1.5sqmm armoured shielded twisted pair FRLS cable

Supply, Installation, Testing & Commissioning of 1.3 MP Fixed indoor dome IP camera

Supply, Installation, Testing & Commissioning of 1.3 MP Fixed outdoor bullet cameraBullet IR IP based camera

Supply, Installation, Testing & Commissioning of 1/2.8" CMOS Sensor, 2.0MP, 2.8~12mm varifocal IP Camera

Supply, Installation, Testing & Commissioning of NVR (Network Video Recorder) 16 Channel with 2 SATA slots

Supply, Installation, Testing & Commissioning of 4 TB HDD

Supply, Installation, Testing & Commissioning of 3 Core 1.5 Sqmm armoured Power Cable

Supply, Installation, Testing & Commissioning of 8 Port switch

Supply, Installation, Testing & Commissioning of 1 KVA line interactive UPS

Supply, Installation, Testing & Commissioning of 12V/26AH X2 Nos. SMF Battery for 30 mints back up

Supply, Installation, Testing & Commissioning of 32" Monitor

(D) STAGE LIGHT:- SITC of 1000W spun aluminium PARCAN made out of spun aluminium 16 SWG in 2 piece cyclindrical construction with punched slot on Parcan housing for natural ventilation and floating ceramic GX16d base lamp socket, 3mtr copper flexible PVC insulated power cable with 3 pin CE insulated plug, Yoke made of MS flat 25 X 3mm with 13mm free mounting hole to fit the adaptor, spigot with 28mm and filter frame but without lamp."Lamp: 1000W 240V PAR-64,Lamp Socket: Ceramic type GX 16D.Power Cable: 3 core,1 Sq.mm copper PVC insulated flexible cable with 10 amps double pole toggle switch, Housing: Aluminium sheet cylindrical construction with black epoxy polyester powder coated" "Switching options: Local control and Digital DMX control through DimmerDimming option: Digital DMX control through Dimmer Yoke: Fabricated using MS flat-accepts mounting on 28mm spud.

SITC of 3x54W LED par light complete with 8-channel DMX 512, high brightness mixing color evenly, stable performance with sound active auto, DMX, and power and DMX loop in and out option, undergone through 7 Tank chemical treatement to keep them rust free and, duly powder coated in black matt texture finish and technical specifications as below. • Lamp - 54 X 3W RGB LED (12R+18G+18B+6W) • Power consumpsion - 150W • Power supply - 230/240V AC • Power cable - 3 core 1.5 sq. mm. copper PVC insulated • Channels - 8 Channel DMX-512 • Beam angle - 25° (15°, 45° optional) • Control mode - DMX, and Manual. • Function - strobe, Dimming, sound active.

SITC of 750W stage 19° profile spot light powder coated diecast body with below specification • Lamp 750W HPL • Beam spread 19° • Dimension of 560 x 340 x 430mm • Weighing 6.2Kg, • Dichroic reflector, • G9.5 lamp base • 4 Beam shaping shutters • 3mtrs power cord with 16amps CE plug • Normal yoke with adjustable keys for tilt rotation • Fine adjustment in lamp focus position for adjustment

ACCEESSORIES -SITC of Diecast aluminum "C" clamp with safety locking chain, duly powder coated in black matt texture finish and technical specifications as below. • Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key. • Receptacle - 28mm standard TV spigot. • Safety - MS Galvanized chain with pin. • Finish-Pretreated and black epoxy polyester powder coated.• Self weight-0.54Kg • Safe working load – 150Kg.

SITC of 1.5mtr long safety bond with lock clip to be fixed around the grid and each lighting fixture to avoid fall of the fixture in case if the "C" clamp is not locked properly . SWL 100Kgs.

SITC of MS suspender consisting of fish plate of 150X150X6mm undergone through 7Tank chemical treatement to keep them rust free and with requisite anchor fastner, duly powder coated in black matt texture finish & stud with 12mm threaded rod to keep the "C" track rigidly held With SWL of 200kg.

SITC of Extruded MS "C" track size 50x40, provided with oval slots(14x40mm), undergone through 7 Tank chemical treatement to keep them rust free powder coated(To create fixed grid at top the stage area to suspend the lighting bars, stage drapery etc. .

SITC of Fixed FOH bar, length 12 mtrs made using 40NB dual barrel with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish

SITC of Fixed front Light bar, length 14 mtrs made using 40NB dual barrel with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish

SITC of MS, Wing Frame,made out of 25X25mm MS square pipe with 2mm in thickness powder coated , provided with 1.5meter wing track of 40X70mm with gridmount brackets made of 40X50X40mm C track Pivotable 4wheeled suspension trolley Extruded track Aluminium I Profile to be laid through out the dept of the stage.

SITC of MS lighting Power junction box for dimmer and direct points,undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with matt black texture finish for dimmable points along with the FC11 naylon gland. (a) MS 16A CEE 3 pin socket for dimmer points size of 126mm x 112mm x 50mm (a) MS 16A CEE 3 pin socket for dimmer points size of 126mm x 112mm x 50mm

SITC of MS DMX lighting junction box for dimmer and direct points,undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with matt black texture finish for dimmable points along with the FC7 naylon gland. (a) MS sheet metal fabricated DMX OUT junction box for dimmable points size of 126mm x 112mm x 50mm

(b)MS sheet metal fabricated DMX IN junction box for dimmable points size of 126mm x 112mm x 50mm

(c)MS Fabricated duly powder coated DMX loop box with DMX male/Female 500mm loop cord size of 126mm x 112mm x 50mm

SITC of MS perforated cable trays of size 150 x 40mm and 300 x 40mm, 2mm in thickness with cable tray lid treated with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with matt black texture finish paint along with clamping arrangement assuring all the cables to be concealed in them a).Size 40 x 75 x 40mm

SITC of Digital Lighting Console with 96dimmer channels with 24 faders, 24 faders x 4 pages,Power Supply: 90-240V AC, 45-63 Hz,Digital Control Signal input/Output: DMX 512/1990 Digital Control Channel: 512 Channel by Patch able to control CH97-CH512.,Audio Input: internal microphone MAX 120dB, output max. value: AC100mV,Gooseneck connector stand: XLR 3pin, DC+12V 250mA,Memory Card:64K*2,Dimension: 19"8U Standard rack (482X352X125mm),Weight: 5Kg

SITC of DMX signal cable for DMX network.

( E ) AIR CONDITIONING SYSTEM :- Supply installation,testing & commissioning of modular type variable refrigerant flow/variable refrigerant volume air cooled outdoor units suitable for cooling and heating, having all hermetically sealed inverter type scroll compressor(s), minimum two compressors for above 14HP modules, microprocessor based controller, top discharge type condensing unit(s), with R410a refrigerant, vibration isolators, with suitable foundation etc. Complete as per specification. The unit shall deliver the rated capacity at AHRI conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400v +/-10%, 3phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as per specification. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 [188HP (60+60+34+34)]

Supply, installation, testing and commissioning of following minimum capacity 4-Way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fansection with low noise fan/dynamically balanced blower, multispeed motor, coilsection with DX Copper coil, electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as per specification. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19Degree C WB temperature. 3.5 - 4.0 TR

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall Type Indoor unit equipped with synthetic washable media pre-filter, fansection with low noise fan/dynamically balanced blower, multispeed motor, coilsection with DX Copper coil, electronic expansion valve, outer cabinet, vibration isolators, cordless remote control, drain pan, necessary accessories/Supports etc., suitable for operation on 230V±10%, 50Hz single phase AC supply, complete, as per specification. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19Degree C WB temperature. 1.8 - 2.2 TR

Supply, Installation, Testing and commissioning of factory built floor/ceiling mounted DX type double skin type horizontal/vertical air handling units made of 25mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8 mm inside layer with polyurethane foam (PUF) insulation (having density 48 kg/cu m) factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as per specification, minimum 4 bend GSS/PVC eliminators, DX type cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5mm) cooling coil of 6 row deep, filter section with 50mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% volts, 50Hz, 3 Phase AC supply suitably designed for varialbe frequency drive applications, drain connections, stainless steel (18G) drain pan with PUF insulation, 150 mm dia. dial type pressure gauges (2 nos.)and industrial type thermometers (2 nos.) at the inlet and outlet of coil, auto purge valve wherever required, including starter Pannel of suitable capacity, necessary vibration isolation arrangement, with mixing Box etc. complete as per specification and of following capacities. 10000 CFM

Supplying and fixing of approved make ductable split type Air Conditioner unit with single/ multi compressure unit and fixing cooling unit (copper coil) at desired location with hanging/ fixing arrangement, condensing unit (copper coil) on out side wall/ ceiling/ floor at desired location having standard length of/ upto 3 metre of copper piping with insulation and drainage pipe upto 1.5 metre length, necessary wiring but excluding ducting work etc complete as per specification with 5 years compressor warranty. 16.5/17.0 ton capacity

Supplying of approved make Hiwall split Inverter type Air Conditioner unit with cooling unit (copper coil) and condensing unit (copper coil) including 5 years compressor warranty and standard length of upto 5 metre of copper piping with insulation etc complete as per specification: 2.0 Ton split type Inverter AC {3 Star}

Installation of split type Inverter/Non Inverter Air Conditioner unit, cooling unit on wall inside and condensing unit on out side wall/ ceiling/ floor at desired locations with existing standard length of copper piping with insulation and power cable including providing and fixing necessary good quality powder coated MS frame etc complete as per specification. (Extra length of copper piping and power cable shall be paid extra on linear basis)

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as per specification : 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.9 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19.1 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn)with tube thickness 1.2 mm with 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn)with tube thickness 1.2 mm with 19 mm thick insulation

28.6 mm dia (OD) (Hard drawn)with tube thickness 1.2 mm with 19 mm thick insulation

31.8 mm dia (OD) (Hard drawn)with tube thickness 1.62 mm with 19 mm thick insulation

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

41.3 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supplying and installation of Refnet Joints as per site conditions.

All Control /communication wiring between indoor and Outdoor Units with FRLS PVC conduit and necessary clamps/saddling etc. complate as requird.

Supplying, laying, fixing and installation of rigid PVC drain piping of 6 KG/sqcm, duly insulated with 6/9 mm thick nitrile rubber pipe section, complte with all necessary fitting such as elbows, tees, reducers, serviceable "P" traps etc. and supports such as clamps etc. complate as per specifications. 25 MM DIA

32 MM DIA

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as per specification. Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Thickness 1.00 mm sheet

Thickness 1.25 mm sheet

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as per specification.

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as per specification. Fire damper

Actuator

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (class "O") insulation on existing duct after applying two coats of cold setting adhesive (CPR X compound). The joints shall sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specification. 19mm

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as per specification.

Supply & fixing Of MS stand for outdoor units

Supply & fixing Of Branch Kit Joints.

SITC Of VRV System including topping R-410 gas as per site requirements. Refrigerant shall be environment Friendly R-410

400 mm Wide G.I. Tray Covered with G.I. Sheet for Copper Tubes.

(F) SOUND SYSTEM:- Floor/ Flying Dual 15 Inch Subwoofers , Flying ,Line arrayble Full Size dual 15", subwoofer element . The subwoofer must have frequency range of 30Hz-3200Hz(-10dB), sensitivity (1W/1m)101 dB SPL or more, delviering Max SPL of 137dB or more with power handling peak of 4000W or less. The speaker should have a nominal impedance of 4 Ω.The loudspeaker should have atleast 26 or more suspension points and should be riggable in the same array as the main speakers using OEM brackets only.

Front Of the House (FOH) Line Arrayable Speakers - Left & Right Line arrayble 15", 2 Way, bi-ampable speaker having 1.75" or bigger HF compression driver. The speaker should have Freq. Response (-3 dB): 70 Hz - 14 kHz, Frequency range (-10dB) 42 Hz - 18 kHz, sensitivity (1W/1m) ≥ 100 dB SPL, delviering Max SPL ≥ 134dB with power handling ≤ 500W @ 8Ω. The speaker should have a nominal impedance of 8 ohm .The speaker should have a coverage angle of at least 85° X 85°. Speaker must have at least 20 suspension points.

Front Fill SpeakersWall mountable 2 way speaker, consisting of two 5.25” or better LF drivers & one 1 "or better HF driver, frequency response (-10 dB) : 62 – 19 KHz., sensitivity (SPL 1W/1M) > 93 dB with max SPL of >117 dB , Long term program power handling capacity ≤ 300W (at nominal impedance of 8 Ω) , coverage (H x V) 90° x 70° or better, with OEM bracket included.

Delay Speakers Wall mountable 2 way speaker, consisting of two 5.25” or better LF drivers & one 1 "or better HF driver, frequency response (-10 dB) : 62 – 19 KHz., sensitivity (SPL 1W/1M) > 93 dB with max SPL of >117 dB , Long term program power handling capacity ≤ 300W (at nominal impedance of 8 Ω) , coverage (H x V) 90° x 70° or better, with OEM bracket included.

Green Room & Control Room Speakers Dual 4" two-Way Speaker with a Frequency Response(-10dB):- 70Hz-20Khz & Long Term Program Power Handling of ≤ 200W (at Nominal Impedance of 8ohms). The Loudspeaker should have a Sensitivity(1W/1m) of atleast 88dB with a Max. SPL of >112dB. It should have Built in LMT with Power Taps of 7.5/15/30W at70/100V Line. The Sound Dispersion should be 120x70 Degrees or more. The Speaker Should Come with OEM wall Mounting Bracket.

Powered Stage Floor Monitor speakers 12" Two-way Powered Speaker with one 1.5" HF Titanium Diaphragm compression driver with a Frequency Response(-3dB):- 68Hz-18KHz & In built Power amplifier of 1000 W or better. The Loudspeaker should have a Max. SPL of >125dB.The Sound Dispersion should be 90x55 Degress or better. The speaker should have both built in line level inputs. It should have polypropylene enclosure.

22 Channel Audio Mixer 22 channel Compact Mixing System (18 x Mic/Line + 4 x Mic/Stereo-Line), Auxiliarys (MON, FX, AUX) : 2 Pre, 2 Post, 2 Pre/Post switchable, Frequency Response, -3 dB, ref. 1 kHz : 15 Hz to 65 kHz, Crosstalk, 1 kHz Channel to Channel < -80 dB, THD at 1 kHz < 0.005%, CMRR MIC input 1 kHz > 80 dB, Dual stereo 24/48-bit multi effects processors, 100 Factory + 20 User, Tap-Delay, Digital Audio Interface Channels : 4 In / 4 Out, AD/DA Conversion, Sampling Rate : 24-bit, 44.1 / 48 / 88.2 / 96 kHz

Wired Vocal Microphone Corded Vocal Microphone with Dynamic Neodymium Magnet microphone element,with frequency response 80Hz-16kHz,Super-Cardioid polar pattern,sensitivity of 2.2mV/Pa and output impedence 600 ohm

Wired Instrument Microphone Corded Instrument Microphone with Self Biased condensor microphone element ,with frequency response of 55Hz-16kHz ,Cardioid polar pattern,sensitivity of 5.5mV/Pa ,rated impedence of 200 ohm ,maximum spl :130dB SPL and dynamic range ;107dB

Kick Drum Microphone Corded Kick Drum Microphone with Dynamic Neodymium Magnet microphone element,with frequency response 20Hz-10kHz,Super-Cardioid polar pattern,sensitivity of 0.5 mV/Pa and rated impedence 150 ohm

Wireless Handheld Microphone Handheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz

Wireless Headworn Microphone Wireless headworn Mic with omnidirectional polar pattern for transmitter,Condenser microphone element , Receiver frequency response 90Hz-17kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 10 mV/Pa & frequency response 50Hz-19kHz

1/2 wave flex antenna, 610-710 mhz

Amplifier for Subwoofers 2 channel class D/H Power amplifier with built in Audio Digital Signal Processor, a Maximum Output Power ≥ 900W@8 ohms, ≥ 1750W@4 Ohms, ≥ 1200W@ 70 Volts, ≥ 2000W@ 100 Volts;Max Bridged Output Power ≥ 5500W @ 4 ohms,Frequency Response (+/- 1dB) ref. 1 KHz:15Hz - 20 KHz,Max input level:+21dBu,Crosstalk< - 80dB,input impedence:20kohm,signal to noise ratio >109 dB,with built in Digital Signal processor like - 31 Band Graphic Equalizer per channel, Parametric Equalizer per channel, Output delays, Audio Limitters, Audio Filters

Amplifier for FOH Speakers 2 channel class D/H Power amplifier with built in Audio Digital Signal Processor, a Maximum Output Power ≥ 900W@8 ohms, ≥ 1750W@4 Ohms, ≥ 1200W@ 70 Volts, ≥ 2000W@ 100 Volts;Max Bridged Output Power ≥ 5500W @ 4 ohms,Frequency Response (+/- 1dB) ref. 1 KHz:15Hz - 20 KHz,Max input level:+21dBu,Crosstalk< - 80dB,input impedence:20kohm,signal to noise ratio >109 dB,with built in Digital Signal processor like - 31 Band Graphic Equalizer per channel, Parametric Equalizer per channel, Output delays, Audio Limitters, Audio Filters

Amplifier for Front Fill & Delay Speakers 2 channel class AB Power amplifier with built in Audio Digital Signal Processor, a Maximum Output Power ≥ 330W@8 ohms, ≥ 650W@4 Ohms; Max Bridged Output Power ≥ 1800W @ 4 ohms,Frequency Response (+/- 1dB) ref. 1 KHz:15Hz - 20 KHz,Max input level:+21dBu,Crosstalk< - 80dB,input impedence:20kohm,signal to noise ratio >103 dB,with built in Digital Signal processor like - 31 Band Graphic Equalizer per channel, Parametric Equalizer per channel, Output delays, Audio Limitters, Audio Filters

Amplifier for Green Room & control room Speakers Single Channel amplifier providing 70V/100V Rated Output Power; THD<1%, 1kHz; 270W ;Rated Output Power ;THD<0.2%, 20Hz…20kHz ; 250W Slew Rate at 1kHz 41V/μs ;Frequency Response, (-1dB,). 1kHz 70Hz - 20kHz; Power Bandwidth THD=1%,Half Power : 45Hz - >20kHz;Input Impedance, 20Hz ... 20kHz, Balanced; > 20kOhm; Signal-to-Noise Ratio, A-Weighted > 101 dB

Volume Control for Green Room & Control Room Monitor Speakers

Equpment Rack

2.5 sqr mm speaker Cable

23/0.2 mm mic cable

NL8,XLR,Phono,RCA etc

OEM SUPPLIED

POWER PROTECTOR

Patch Box with 4 connectors for mic on stage

MIC STAND

SINGLE JACKET CABLE FOR MULTIPLE CONNECTIONS

SYSTEM INSTALATION AT SITE WITH PROGARMMING

( G) LED SINAGES & PROJECTOR :- Supplying, installation, testing and commissioning of following LED Strip Light fitting complete with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and furnishing 5 Yrs Warranty certificate from manufacturer. P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-65 5 watt per metre LED Strip

Supplying, installation, testing and commissioning of following LED Signage entry/exit, fitting complete including built in battery backup for 2 hour with Electronic Driver Heat sink Capacitor and all other accessories, including connection, earthing etc complete as per specification and furnishing 5 Yrs Warranty certificate from manufacturer. P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. IP-20 Single sided LED Signage

Supplying, installation, testing and commissioning of following RGB LED Flood Light fitting (luminaries) complete with electronic driver heat sink capacitor and all other accessories etc. as per specification 60 watt

LED Glow sign board Supplying, installation, testing and commissioning of Acrylic LED light

Supplying, installation testing and commissioning of standard/ short/long throw multimedia protector with display device- DLP technology and above, minimum No. of pixels 1024x768, computer compatiblity- UXGA/WXGA/SXGA/XGA, minimum life of light source-5000 hours, network terminal wired/ wireless with inbuilt speaker including all accessories and specifications as per site requirement. Brightness: 5000 Lumens

Supply and installation of Wallmount motorized projector screen, 1080p, 3D and 4k supported display technology, including all accessories and specification as per site requirement

( H ) AREA LIGHTING WORK :- Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ concealed, steel/ PVC conduit/ PVC casing caping as required. 5.11.12 3 x 2.5 sq. mm

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. 150 watt

Supplying of following 230/250 volts LED Flood light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Seperate housing for driver etc complete as per specification and P.A. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. 100watt

Supply of hot dipped galvanized (in single dip to average 70 micron) octoganal pole made of 3mm thick steel plate having base plate 240x240x16mm, window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, including template and anchor plate 240x240x3mm with 4 nos 20mm dia 700mm long foundation bolts (EN8 grade). 21.7.2 8 metre high, minimum dia 150mm at bottom and 70mm at top

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as required. 21.9.3 Single Over Hang 1.50 metre Long

Erection of GI octogonal/ tubular pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as required. 21.11.6 8 metre high

Supplying and laying following size medium class G.I. pipe in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.3.2 80 mm internal dia

Supplying and laying HDPE pipe of 4kg/sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.2.1 63 mm outer dia

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 11.1.1 3 pole MCCB, 25-63A, Fixed Thermal Release, 10KA

Supplying and fixing TP MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as required. 11.14.2 6 amps to 32 amps

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured) 9.19.2 Above 300 mm and upto 450 mm deep

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as required. 9.20.1 100 amp (20x5mm)

Providing and making interconnection in cubical panel between BBC and switchgears with following size aluminium strip of length upto 50cm as required (To be measured separately for each phase/ neutral). 9.16.1 20x5mm (100 amps)

Providing and fixing following rating current transformer in existing cubical panel including, connections, testing and commissioning etc. as required. 12.15.2 100/5 amps

Providing and fixing 3 pole, 415/500 volts following rating (AC-1 Duty) power contactor in existing starter/ cubical panel including, connections, testing and commissioning etc. as required. 12.13.4 100 amps

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as required.

Providing and fixing penal mounting following rating digital type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 12.19.2 0-100 amps

Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 12.20.2 Digital type

Providing and fixing following Time switch (timer) in existing panel including connection, testing and commissioning as required. 12.22.1 Digital type

Supplying, installation, testing and commissioning of following 230/250 volts LED Post Top Lantern fitting with perplex cover/decorative diffuser, electronic ballast and all other accessories on existing gate column/ pole bracket, including connection, earthing etc complete as per specification and P.F. should be greater than 0.9 . LED chip efficacy ratio ≥ 100 lumens /watt. 25 Watt

Supply of GI PIPE POLE made of "B" class GI pipe making necessary hole for cable entry and providing earthing stud (welded at specified height) including painting with one coat of red oxide zinc chromate primer. 50 mm dia

Providing and welding M.S. base plate of size 300x300x3mm at bottom of GI/MS pipe pole.

Erection of STEEL TUBULAR or "H" BEAM/ ISMB pole in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation and cement concrete collar of size 0.4 metre dia and 0.50 metre height from ground level including excavation and refilling etc. as per specification of length: Upto 3.0 metre

Supplying and laying following sizes one number FRLS PVC insulated/XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground at a depth not less than 40 cm and upto 90 cm including excavtion, sand cushioning, protective covering and refilling the trench etc as per specification, IS: 1554 (1988, Part 1) / IS: 7098 (1988, Part 1). 2 x 10 sq. mm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 17.1.23 4 x 16 sq. mm.

4 x 25 sq. mm.

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as required. 17.23.24 4 X 16 sq. mm (22 mm)

Supplying following sizes ISI marked FR PVC insulated copper conductor, single core cable in company pack coils. 34.1.1 1.5 sq. mm

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required.

Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supplying and laying following size medium class G.I. pipe in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.3.1 50 mm internal dia

Supplying and laying HDPE pipe of 4kg/sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.2.1 63 mm outer dia

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement (minimum 90kg per cum), form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required.

( I) DG SET :- Supplying, installation, testing and commissioning of following capacity diesel Generating Set (alternator directly coupled to diesel engine) compete in all respect broadly comprising of following and as per specification. A. Alternator : Self excited, brush less type, of following capacity, 3 phase, 415 volts 50 Hz, 4 pole, AC alternator complete with all accessories. B. Engine : water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification. C. AMF Panel : Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches, meters and other accessories, internal wiring, connection, inter-connection etc. for trouble free smooth functioning of DG Set complete with battery charger and leads as required. D. Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as required. 24.3.6 200 KVA

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement (minimum 90kg per cum), form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required.

Providing and making suitable CC pole collar (muffing) in Cement Concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) of size 0.4 m dia and 0.4 m height from existing CC foundation.

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 17.1.19 3.5 x 240 sq. mm.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

( J) SUBSTATION :- Supplying and installation of outdoor type Transformer ONAN type with copper winding having following continuous KVA rating, 33 /0.415 KV 3 Phase 50 Hz Vector group DY-11, tapings in steps of ± 2.5%, ± 5%, --7.5% with oil conservator, silica gel breather having connecting terminals on HV side suitable for bare conductor connection, cable end box on medium voltage side suitable for 1.1 KV 3½ core UG cable and confirming to IS:2026, on existing Brick /CC/RCC platform with all fittings, accessories, filled with filtered transformer oil including testing and commissioning etc. complete as required 24.2.1 500 KVA

Supply and fixing following overhead line accessories. 22.1.12 DC cross arm made of MS channel 100x50x5 mm @ 9.56 kg/m

Supplying of angle/channel iron cross arms/ bracket/ other fitting of approved size and shape including drilling of holes for insulator pins, bolts and nuts etc as required.

Supplying and fixing approved make 33 KV glazed porcelain pin insulator with G.I. spindle on existing pole bracket with necessary materials as required:

Supplying and fixing approved make 33 KV (3x11KV) glazed porcelain disc type insulator with tension hardware on existing pole/ support/ cross arm channel as required complete:

Supplying and erection of 33 KV gang operated air break switch on existing two pole structure with insulators and all other accessories complete including locking arangement as required.

Supplying and erection of 33 KV D.O. fuse unit on existing two pole structure with insulators and all other accessories complete including locking arangement as required.

Supplying and erection of single piece nonlinear resistor type lightning arrestor suitable for 3 wire, 33 KV overhead lines with rated voltage 30 KV (rms) with a nominal discharge current rating of 10 KA (station class) and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Supply and erection standard ACSR (aluminium conductor steel reinforced) confirming to IS 398-1961 of approved make at existing insulator at height upto 14m from ground level including stringing, binding with insulator, jointing wherever required, jumpering, tearing off connection etc complete etc. as required including clearing off obstacle if any: 22.32.4 Raccoon 6/1/4.09mm dia with calculated aluminium area 78.83 sq.mm , weight 319 kg/ km (198 amps)

Dog 6/4.72(AL), 7/1.57(S) mm dia with calculated aluminium area 105 sq.mm , weight 394 kg/ km (248 amps)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required.

Supplying and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including soldering etc. as required.

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode at 0.5 Metre depth below ground level including excavation and refilling the trench etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as required.

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 17.1.20 3.5 x 300 sq. mm.

Supplying and making outdoor end termination with cast resin compound including aluminum lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminum conductor power cable of 1.1 KV grade as required. 17.25.9 3½ X 300 sq. mm

Supplying and laying following size RCC Hume pipe class NP-2 (in standard length of 2 metre) with collar in ground below road, path etc at a depth not less than 50 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.4.1 100 mm dia

Supplying and laying HDPE pipe of 4kg/sqcm in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as required. 16.2.1 63 mm outer dia

Earth work in soft rock with all lead and 1.5 metre lift, dressing, stacking excavated strata including refilling with excavated soil in trench / pit to ground level complete as required

Providing and laying Cast-in-situ cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm including mixing with mechanical mixer, compacting with vibrator, finishing and currying etc. complete but excluding form work.

Applying priming coat on steel work with red oxide zinc chromate primer.

Painting wood steel and other metallic surface with Aluminium Paint complete with material and labour including preparation of surface.

Plastering 15 mm thick on brick work/ CC surface with cement mortar 1:4 (1 cement : 4 fine sand) at all levels.

Providing and making interconnection in cubical panel between BBC and switchgears with following size aluminium strip of length upto 50cm as required (To be measured separately for each phase/ neutral). 9.16.7 100x6mm (800 amps)

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and following depth made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ammeters etc as per specifications including powder coating painting but without busbars, switchgears and other accessories etc complete as required. (Only face area is to be measured) 9.19.2 Above 300 mm and upto 450 mm deep

Supply, installation, testing and commissioning of 4 pole (3 phase + neutral) aluminium bus bars in existing cubicle type compartmentalized wall/ floor mounted panel board along with suitable size and shape insulators, necessary bolts and nuts etc complete as required. 9.20.7 800 amp (100x6mm)

Providing and fixing approved make, Electrically Operated, draw out type, 415/500 volts, 4 pole air circuit breaker complete with all standard accessories as per manufacturers specifications including drilling holes on the board, connections, earthing the body, testing and commissioning etc. as required. 12.2.1 800 amps, 4 pole, 50 KA

Providing and fixing penal mounting following rating digital type ammeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 12.19.5 0-1000 amps

Providing and fixing penal mounting 230 volt LED type indicating lamp in existing cubical panel including, connections, testing and commissioning etc. as required.

Providing and fixing penal mounting 0-500 volt voltmeter of size 100x100 (NS) in existing cubical panel including, connections, testing and commissioning etc. as required. 12.20.2 Digital type

Supply of "H" beam steel pole as per IS specifications in standard length for over head line work: 21.1.2 "H" beam steel pole 152x152x7x12 mm standard weight 37.1 kg /metre

Supply of GI PIPE POLE made of "B" class GI pipe making necessary hole for cable entry and providing earthing stud (welded at specified height) including painting with one coat of red oxide zinc chromate primer. 21.4.1 50 mm dia

Erection of steel tubular or "H beam POLE STRUT in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling and securing with holding clamps, bolts and nuts etc. as required:

Supplying and erecting MS gate of approx. size 3.0 m (W) x 2.0 m (H) in two laps for electric sub-station switch yard fencing frame made of angle iron size 50 X 50 X 6 mm on top bottom and sides fitted with flat iron support of size 25 X 6 mm on mid way horizontaly and square bar of size 8 mm at every 100mm vertically including 3 sets of heavy duty MS hinges and aldrop complete duly painted with one coats of red oxide and two coats of approved colour paint.

Supplying and erecting chain link mesh fencing for electric sub-station switch yard of 2.5 m approx. height from ground level using angle iron size 50 X 50 X 6 mm erected in C.C. foundation 15 X 15 X 40 cm deep at every 2 metre fitted with flat iron support of size 25 X 6 mm on top, bottom and mid way and chain link mesh 50 x 50 mm aparture and 4 mm dia G.I. hard wire securing and screwing with 2mm dia G.I. wire, G.I. staples, G.I.U-nails or steel pins to the angle iron at every distance of 30 cms, by iron studs complete duly painted with one coats of red oxide and two coats of approved colour paint. (Area of fencing i.e. height x length is to be measured)

SOR Name

RES_BUILDING

NON DSR BUILDING 2018

BRIDGE

DSR BUILDING 2016

NON SOR

CPWD DSR 2016

PWD ROAD

ELECTRIC

PMGSY SOR

Creda SOR

PWD BUILDLING

DSR ELECTRICAL 2016

Siemens Per meter

AMPOULE

Price Should be quoted as per SKU in Aneexure-I of Tender Document

As per Tender

Single Rate (1 Tablet/1 capsule/1 Amp/1 Vial /1 Bottle/1 Kit/1 Test Kit)

Activity unit

barrel

Batch

BOTTLE

Gallons per hour (US)

Brass

Billing Rate Per Month

Bottle

Bundle

Cubic sentimeter /second

Canister

Carton

Cubic Centimeter

Cubic decimeter

Centiliter

Centimeter

Square centimeter

coils

COILS

Copies

Crate

Cu.Mtr.

cubic feet

cubic feet (CFT)

cum.km

Degree

DHQ-BHQ

Decimeter

Dozen

each additional floor

Each Courty

each cut

EACH FRAME

Each rol

each test

each tree guard

each tree guard

Each box

Enzyme Units / Milliliter

Each TAPE

Enzyme Units

For each (Unit) Quantity

For each PPE KIT

For each Test KIT

For each VTM Kit

Fluid Ounce US

Square foot

Cubic Foot

Gigajoule

gram act.ingrd /liter

US gallon

Gram Gold

Gram act.ingrd.

Gram /liter

Gram/Mol

Gram/Kilogram

Gram /square meter

Gram/Cubic meter

Gigaohm

Gallons per mile (US)

Gross

Hectare

hectare

Hectoliter

Horse power

Hours

Hours

hundred Pieces

HALF YEARLY

I/O Point

INHALER

Indian Rupees

Joule /kilogram

Joule /Mol

joint

Kilogram act.ingrd

Kilogram /cubic decimeter

Kilogram

Kilogram/Mol

Kilogram /Second

Kilogram / cubic meter

kg act.ingrd /kg

KILOWATT

Kilojoule/kilogram

Kilojoule/Mol

Kilo Litre

Kilometer

Square kilometer

Kilometer/hour

Kelvin/Minute

Kelvin /Second

Kilonewton per square meter

Kilopascal

Kilotonne

Kilovoltampere

KILOWATT POWER

kwp-dc

US Pound

lemgth

length

Liter per 100 km

litre

Liter /Minute

Liter /Molsecond

Liter Per hour

Lumpsum

LITRE

lumpsump

Meter

1/square meter

Mol per cubic meter

Megawatt hours

Meter /Hour

Mol per liter

Meter /second

Square meter

Square meter/Coat

Square meter/second

Cubic meter

Cubic meter /Hour

Cubic meter/second

Man days

Man-Month

ManDay