REPAIR/MAINT OF DAMAGED FLOOR, WALL TILES, JOINERY AND ALLIED WORKS, REPAIR/MAINT OF BLDG ROOFS INCLUDING ROOF TREATMENT, REPAIRS OF CHHAJJAS, PARAPETS, ATT, PLINTH PROTECTION, FALSE CEILING, ROOFING AND ALLIED WORKS IN TECHNICAL AREA, REPAIR/MAINT

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backin), removing serviceable tiles to store and rubbish off the premises, complete as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L glazed ceramic coloured tiles in vertical surface 350 x 250 x 7mm/450 x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 10mm thick (square/rectangular) area of each tile exceeding 0.42 Sqm but not exceeding 0.1 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for non skid ceramic coloured tiles 10mm thick (square/rectangular) polished vertical surface skirting/dado area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement of match the surfaces over and including 10mm thick rendering in CM (1:4), complete all as specified and directed.

S & F 110mm bore PVC (SWR) soil waste and vent pipes, single socketed, in any length with sealant rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm bore, PVC (SWR) bends of any radius, complete all as specified and directed.

Demolition of plain cement concrete in ground floors and pavings n. exc. 15cm thickness (below or above ground level), complete all as specified and directed

M&L for 75mm thick PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection/hardstanding etc and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for post construction anti-termite treatment by treating the soil under plinth protection by using chemical emulsion @ 5 litres /Sqm of surface area, complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) not exc. 1.5 Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc. 1.5 Sqm but n.exc. 4 Sqm each, complete all as specified and directed.

Taking down shutter of any description exc. 1 Sqm but n. exc. 2 Sqm each, complete all as specified and directed.

S&F factory made 100% solid WPC (wood polymer composite) door frame 125mm x 80mm double rebated mullein section made from wood polymer composite ( single extruded process) material comprising of virgin PVC polymer of 'K' value 57-60 (suspension grade), calcium carbonate and natural fiber (wood powder/rice husk/wheat husk) and non toxic addictive fabricated with meter joint after applying PVC solvent cement & screwed with full body treated star headed screws having minimum frame density of 780 kg/cbm, having good screw holding capacity (screw withdrawal strength of (min 990 N), minimum compressive strength of 58 N/mm2, modules of elasticity 900 n/mm2 and resistance to spread of flame of class A category with property of being termite/bore proof, water/moisture proof & fixed imposition with SS dash fasteners/hold fast of required dia and length, all as per specifications drawing, complete all as specified and directed. Note :- (i) Manufacturer test certificate and authentication should be produced by the contractor from the manufacturing company. (ii) Hold fast or dash fasteners shall be paid separately.

S&F 75mm size MS butt hinge, heavy weight, cold rolled mild steel, complete all as specified and directed.

S&F 100mm size MS butt hinge, heavy weight, cold rolled mild steel, complete all as specified and directed.

M&L 35mm thick 2nd class hardwood factory made plain framed panelled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12 mm veneered particale board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I) kiln seasoned and chemically pressure treated, complete all as specified and directed.

S & F 30mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc, complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for preparation of old painted surfaces of wood or wood based material and applying one coat of synthetic enamel paint (1st grade quality) on surface of any description over 10cm width or girth, complete all as specified and directed.

Hacking out old broken glass (any thickness,size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty or wooden bedding in square n exc 0.5 Sqm in each pane, complete all as specified and directed.

S & F 5.5mm thick ordinary glass, pin head type and glazing in aluminium section in square exc 0.5 Sqm each pane, complete all as specified and directed.

S&F in reapair double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel, heavy duty, complete all as specified and directed.

Taking down and refixing anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including existing joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc, complete all as specified and directed.

S & F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised door comprising of frame of size 101.60mm x 44.6mm x 2.4mm thick push/pull type glazed door shutter having top and bottom section of size 83 x 44.5 x 2.4mm and 100 x 44.5 x 2.4mm thick respectively, styles section of size 80 x 44.5 x 2.4mm thick and lock rail of size 100mm x 44.5mm x 2.4mm thick including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size including 5mm thick tinted sheet glass in both panel, hinges, mortice lock, stays & aluminium anodised handle of suitable size, etc, complete all as specified and directed.

Supply and fix for 150mm long aluminium anodized barrel tower bolts of extruded section, complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple(bolt type) and fixing clips of sheet,cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy, complete all as specified and directed.

S&F 150mm long aluminium anodised handles, cast type, complete all as specified and directed.

S&F in repair door closer hydraulically regulated, aluminium (die cast) body designation No 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg, complete all as specified and directed.

S&F mild steel hold fast, MS flat iron for chowkhats and other small articales including making shape, drilling hole etc, complete all as specified and directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in hold fast block including necessary form work, complete all as specified and directed.

Taking out old damaged tarfelt or membran of any description including screed bed or bedding layer and removing of debris to a distance exc. 100m and n. exc. 250m and cleaning roof surfaces to remove all loose dust etc., roughening surfaces of old concrete roof by picking, sweeping clean and washing down with water using wire brush, brooming down and applying the following treatment all as directed in order of precedence as stated: (a) Brushing neat cement slury with 3.0 kg of cement per Sqm. (b) 15mm thick screed bed or bedding layer in CM (1:3) mixed with water proofing compound as per manufacturer instruction on existing roof surface true to level. (c) Applying one coat of bituminous primer @ 0.40 Ltr/Sqm. (d) Supply and laying 3mm thick APP based polymeric membrane of approved manufactured with weight not less than 3.50 Kgs per Sqm reinforced with non-woven polyester fabric weighing not less than 160gms per Sqm having softening point not less than 15°C, having tensile strength of 650 N/Sqcm and 350 N/Sqcm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180 N by torch application. Polymeric membrane shall be taken to a height of 30cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (e) Applying one coat of aluminium paint @ 0.11 Kg/Sgm over APP membrane surface. Note:- (i) Laying APP based polymeric membrane shall be done torch on method as per manufactures instructions. (ii) A minimum overlap of 150mm and 100mm should be made at the end and sides of the polymeric membrane respectively and sealed all overlaps and joints as per manufacturers instruction. (iii) APP based polymeric membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given in IS 16540-2017/1S 16532 2017. (iv) Contractor shall produce necessary test certificate of the manufacturer to the Engr-in-Charge before incorporation in the work. (v) Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work. (vi) The work shall be executed through authorised applicators of original manufacturer only. (viI) WPC shall bemeasured and paid separately as 'supply only'.

M & L for 40mm thick PCC (1:2:4), type B-0, (using 12.5mm graded crushed stone aggregate), as in padding finished even and smooth without using extra cement, complete all as specified and directed.

S & F 4mm thick non asbestos fibre reinforced designer ceiling board (605mm x 605mm) with hot drip heavy duty suspended ceiling grid system T-2430 with GI frame work for seamless ceiling comprising of GI perimeter channel, unequal flanges and web etc of suitable size suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section including Hangers 6 mm dia GI fixed to roof by means of ceilling cleats made out of GI flat per manufacturers instructions including dismantling of old unserviceable ceiling board any thickness including cover fillets, complete all as specified and directed.

Taking down cement plaster on brick/concrete surfaces of any description in any position incl racking out joints, hacking for key, scrubbing down with water etc and removing rubish off the premises, complete all as specified and directed.

Demolition of brick work or stone masonry, built in CM including all quoins, arches, pillars etc. but excluding ashlar facing, dressed stone work and precast concrete articles , complete all as specified and directed..

M&L for brick work with sub class 'B' bricks old size, burnt clay bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) including demolition of brick work, complete all as specified and directed.

All as per item No. 40.00 here-in-before but except bricks, complete all as specified and directed. Note-(i) Bricks obtained from demolition shall be re-used. (ii) The quoted rate shall deemed to be included for cleaning of old bricks obtained from demolition.

M & L for rendering 15mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces of wall in CM (1:4), mixed with integral water proofing compound top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement, complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item as supply only.)

Supply only liquid water proofing compound conforming to IS: 2645 - 1975 specification, complete all as directed.

M&L for preparation newly plastered surfaces of wall and applying two coats of 100% premium acrylic smooth exterior emulsion paint alkali & fungal resistance of shade deep green/camouflage pattern over a coat of exterior emulsion primer, complete all as specified and directed.

M&L for preparation old plastered surfaces of wall and applying one coat of 100% premium acrylic smooth exterior emulsion paint alkali & fungal resistance of shade deep green/camouflage pattern, complete all as specified and directed.

S&F 40mm nominal bore GI pipe brackets made out of medium grade pipe of required length not less than 1.20m consisting of mounting brackets made out of mild steel FI 40 x 6mm, required shape (two Nos per GI pipe brackets ) duly fitted with 4 Nos Mild steel nuts, bolts and washers in walls /poles etc. including painting with two coats of synthetic enameled paint over one coat of red oxide zinc chrome primer including taking out existing unserviceable GI bracket of any shape/size from pole, complete all as specified and directed.

S&F astronomical time switch in existing street light timer panel for switching on /off lights and other electric devices according to the sunrise / sunset times based on the entered location or location coordinates including taking down old unserviceable time switch, complete all as specified and directed.

S&F in repair contactor TP, 40 Amp, 415 volts, complete all as specified and directed.

S&F in repair MCB Single Pole (SP) of capacity 6 to 32 Amps, 240 Volts, breaking capacity 10 KA, ‘C’ series, with overload and short circuit protection, fixed in proper position including connection and testing, complete all as specified and directed.

M & L for Cleaning of creepers from electric pole, junction box and street light including replacement of cable gland, lugs, MCBs, tightening of earthing, orientation of street light bracket properly, complete all as specified and directed. Note : (i) Cable gland, lugs / thimble, as required, shall deemed to be included in the unit quoted rate. (ii) MCBs shall be measured and paid separately.

S&F LED street light fitting 45 Watt 230 V, AC outdoor type with high pressure die cast metal hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection including taking down unserviceable street light fittings, complete all as specified and directed. (Note :- During approval of make the contractor should submit Technical literature of proposed make.)

All as per serial item No. 51.00 here-in-before but for 60 watt, complete all as specified and directed.

All as per serial item No. 51.00 here-in-before but for 90 watt, complete all as specified and directed.

All as per serial item No. 51.00 here-in-before but for 120 watt, complete all as specified and directed.

S&F in repair PVC insulated & sheathed stranded FR copper cable 3 core of cross sectional area 1.5 Sqmm for providing necessary electrical connection from junction box to light fittings including with suitable size copper lugs including taking down existing cable, complete all as specified and directed.

S&F in repair KIOSK box weather proof made out of PVC and including one piece mounted SMC base and door pole mounted hinged door size 333 x 233 x 200mm out side and 300 x 200 x 105mm inside dimension comprising of aluminum bus bar 4 strips for 3 phase and neutral 63 Amp and 10 Amp MCB for controlling the street light fitting including FI clamps 30 x 4mm with necessary MS nuts bolts and washer including embossing/painting of danger notice of size not less than 10cm x 7.5 cm with letters, figures and conventional skull and bones in signal red colour on front face of KIOSK box body, complete all as specified and directed.

M&L for earthing & testing complete with GI earth plate electrode 60cmX60cmX6mm thick buried directly in ground vertically to a depth not less than 2.25mtr below normal ground level with top edge of earth plate at a depth not less than 1.5 mtr below normal ground level connected to and including earth lead wire 4mm dia by means of bolts, nuts and check nuts and washers etc. made of GI & connected to earthing test point and earth dolly all as shown in elect plate No 3 of SSR Pt I including all necessary earth work, excavation, PCC chamber, (1:2:4) B1 & RCC (1:2:4) B1 chamber cover with suitable reinforcement with handle including 15mm bore GI light grade protection pipe upto 7.5m length & 20mm bore GI medium grade watering pipe and wire mesh, funnel, char coal dust, common salt, wire mesh etc. including taking down unserviceable earthing of any description, complete all as specified and directed. (Note : GI wire from earth pit to panel / pole shall deemed to be included in the unit quoted rate)

Supply only OEM LED driver suitable for 45-50 Watts LED outdoor (Flood light/Street Light) luminaries, complete all as specified and directed.

Supply only OEM LED driver suitable for 60 Watts LED outdoor (Flood light / Street Light) luminaries, complete all as specified and directed.

Supply only OEM LED driver suitable for 120 - 150 Watts LED outdoor (Flood light / Street Light) luminaries, complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metre wide and not exc. 1.5 metre in depth for foundation of pole / stay, or cable trenches and getting out in soft/loose of any type of soil. complete all as specified and as directed.

Returning filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm in soft loose of any type of, soil complete all as specified and directed.

Removing excavated materials to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above thestarting point, all as specified and as directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 40mm internal dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

Supply and laying double walled corrugated (DWC) HDPE duct pipe of 50mm internal dia conforming to IS, approved colour complete with fittings for cable protection, complete all as specified and directed.

M & L for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundation of poles/struts etc, including form work, complete all as specified and directed.

Horizontal boring under the road below 1mtr from the road surface and dial of hole not exc. 100mm, without damaging the existing road, getting out and disposal of soil to a distance not exceeding 50m from the site of work, complete all as specified and directed.

S&F galvanized iron steel tubing 40mm bore (light grade) with all fittings for protection of cables, laid in trenches, complete all as specified and as directed. (Note : Excavation and earth work shall be measured and paid separately )

Supply, laying and testing LT UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 Sqmm 4 core including taking down old unserviceable UG cable, complete all as specified and directed.

All as per serial item No. 69.00 here-in-before but 16 Sqmm 4 core, complete all as specified and directed.

All as per serial item No. 69.00 here-in-before but 25 Sqmm 4 core, complete all as specified and directed.

All as per serial item No. 69.00 here-in-before but 95 Sqmm 3.5 core, complete all as specified and directed.

All as per serial item No. 69.00 here-in-before but 185 Sqmm 3.5 core, complete all as specified and directed.

M & L for danger notice sticker of size 8cm x 8cm, made out of industrial grade vinyl film with UV protected layer, suitable for external use, self adhesive including signage for electric danger with bones and skull, 415 volts etc, complete all as specified and directed

M&L for painting existing steel tubular poles, 7 to 9.0 meter in height above GL including cross arms & bracings on existing surface after cleaning and removing dust, rust & dirt with two coats of aluminium paint over a coat of red oxide primer, painting with black & white alternate strips of 30cm each externally from ground level up to 1.5 mtr with synthetic enamel paint, numbering of pole (MES/SL Number) and white wash on pole coping, complete all as specified and directed.

Note: An amount of Rs.35,480.00 on account of Credit Schedule for schedule 'A' part - II shall be deducted from the total amount of BOQ to arrive at the contract sum.

B L SHARMA (BID ID -3347690)

BHARAT ELECTRIC (BID ID -3348782)

M/S ROY ENTERPRISE (BID ID -3349373)

M/S BIJAY KUMAR SHIVA (BID ID -3349395)