MFM at OR & SS JETTY VNWOTL

SPLY MFM _MS_ OR JETTY — FLOWMETER,MASS,CORIOLIS; DESIGN SPEC,FLANGE(S):ANSI B 16.5; PRESSURE DESIGN,FLANGE:CL150; FLANGE,TYPE:RAISED FACE; MAT,METERING TUBE:STAINLESS STEEL 316/904L; CLASSIFICATION,HAZARD AREAS:ZONE 1, GROUP II A & B T3; INGRESS PROTECTION:1P65,IEC/EN60529; CONNECTION,ELECTRICAL:1/2 FNPT IN; SIGNAL,OUTPUT:4-20 MA; POWER SUPPLY:230 VAC/24 VDC, 50 HZ; TEMPERATURE LIMIT:5-50 DEG C; SERVICE:TO MEASURE VOLUMETRIC FLOW ON BATCHING APPLICATIONS FOR CUSTODY TRANSFER OF WHITE OIL; OPERATING DENSITY:BIS STANDARDS 15-1459 FOR SKO, IS-1460 FOR HSD, IS-2796 FOR MS AND DATA SHEET; OPERATING VISCOSITY:BIS STANDARDS 15-1459 FOR SKO, IS-1460 FOR HSD, IS -2796 FOR MS AND DATA SHEET; CORROSIVE COMPONENT:2500 PPM (MAX) OF SULPHUR AND SUBSTANTIAL AMOUNT OF CAUSTIC IS PRESENT IN HYDROCARBON; ALLOWABLE PRESSURE DROP:PRESSURE LOSS OF 0.5 KG/CM2 ACROSS MASS FLOWMETER AT MAX FLOW CONDITION. NOTE THAT PRESSURE LOSS SHOULD ALSO NOT EXCEED 1.0 KG/CM2 ACROSS ENTIRE PRE-FABRICATED SKID; HUMIDITY LIMIT:95% NON-CONDENSING; MICROPROCESSOR BASED; TRANSMITTER TYPE:REMOTE; MATERIAL, WETTED PART:STAINLESS STEEL 316/904L; FLOW DIRECTION:BI DIRECTIONAL FLOW; OUTPUT:FLOW (MASS AND VOLUME), STANDARD (OPTIONAL) AND AMBIENT DENSITY, TEMPERATURE; MATERIAL, BODY:STAINLESS STEEL 304/EPOXY COATED DIE CAST ALUMINUM; MATERIAL, END CONNECTION:STAINLESS STEEL 316; MATERIAL, FLANGES, REDUCER, EXPANDER, NUTS, BOLT:STAINLESS STEEL 304 OR BETTER MATCHING CARBON STEEL FLANGE; ACCURACY, MASS:+/- 0.05%; ACCURACY, VOLUME:0.1%; DENSITY ACCURACY:+/-0.0005 GM/CC; AMBIENT DENSITY REPEATABILITY:+/-0.0025 GM/CC; STANDARD DENSITY REPEATABILITY:+/-0.0003 GM/CC; LINEARITY:+/- 0.05 %; REPEATABILITY:+/- 0.05%; LOCAL DISPLAY:2 LINE, 16 CHARACTER, SCROLL-TOUCH SCREEN PREFERRED; OUTPUT:FREQUENCY - 10000 HZ FOR FLOW RATE TO BE CONNECTED TO FLOW COMPUTER; EMC COMPLIANCE:THE MASS FLOW SHALL COMPLY WITH GENERIC IMMUNITY STANDARDS EN 50081, EN50082 AND EN 55011 FOR EMISSION; APPROVAL:CCOE/PESO AND CMRI: FOR RTD AND TRANSMITTER IS IN ATTACHED DATA SHEET

SPLY MFM _HSD_ SS JETTY — FLOWMETER,MASS,CORIOLIS; DESIGN SPEC,FLANGE(S):ANSI B 16.5; PRESSURE DESIGN,FLANGE:CL150; FLANGE,TYPE:RAISED FACE; MAT,METERING TUBE:STAINLESS STEEL 316/904L; CLASSIFICATION,HAZARD AREAS:ZONE 1, GROUP II A & B T3; INGRESS PROTECTION:1P65,IEC/EN60529; CONNECTION,ELECTRICAL:1/2 FNPT IN; SIGNAL,OUTPUT:4-20 MA; POWER SUPPLY:230 VAC/24 VDC, 50 HZ; TEMPERATURE LIMIT:5-50 DEG C; SERVICE:TO MEASURE VOLUMETRIC FLOW ON BATCHING APPLICATIONS FOR CUSTODY TRANSFER OF WHITE OIL; OPERATING DENSITY:BIS STANDARDS 15-1459 FOR SKO, IS-1460 FOR HSD, IS-2796 FOR MS AND DATA SHEET; OPERATING VISCOSITY:BIS STANDARDS 15-1459 FOR SKO, IS-1460 FOR HSD, IS -2796 FOR MS AND DATA SHEET; CORROSIVE COMPONENT:2500 PPM (MAX) OF SULPHUR AND SUBSTANTIAL AMOUNT OF CAUSTIC IS PRESENT IN HYDROCARBON; ALLOWABLE PRESSURE DROP:PRESSURE LOSS OF 0.5 KG/CM2 ACROSS MASS FLOWMETER AT MAX FLOW CONDITION. NOTE THAT PRESSURE LOSS SHOULD ALSO NOT EXCEED 1.0 KG/CM2 ACROSS ENTIRE PRE-FABRICATED SKID; HUMIDITY LIMIT:95% NON-CONDENSING; MICROPROCESSOR BASED; TRANSMITTER TYPE:REMOTE; MATERIAL, WETTED PART:STAINLESS STEEL 316/904L; FLOW DIRECTION:BI DIRECTIONAL FLOW; OUTPUT:FLOW (MASS AND VOLUME), STANDARD (OPTIONAL) AND AMBIENT DENSITY, TEMPERATURE; MATERIAL, BODY:STAINLESS STEEL 304/EPOXY COATED DIE CAST ALUMINUM; MATERIAL, END CONNECTION:STAINLESS STEEL 316; MATERIAL, FLANGES, REDUCER, EXPANDER, NUTS, BOLT:STAINLESS STEEL 304 OR BETTER MATCHING CARBON STEEL FLANGE; ACCURACY, MASS:+/- 0.05%; ACCURACY, VOLUME:0.1%; DENSITY ACCURACY:+/-0.0005 GM/CC; AMBIENT DENSITY REPEATABILITY:+/-0.0025 GM/CC; STANDARD DENSITY REPEATABILITY:+/-0.0003 GM/CC; LINEARITY:+/- 0.05 %; REPEATABILITY:+/- 0.05%; LOCAL DISPLAY:2 LINE, 16 CHARACTER, SCROLL-TOUCH SCREEN PREFERRED; OUTPUT:FREQUENCY - 10000 HZ FOR FLOW RATE TO BE CONNECTED TO FLOW COMPUTER; EMC COMPLIANCE:THE MASS FLOW SHALL COMPLY WITH GENERIC IMMUNITY STANDARDS EN 50081, EN50082 AND EN 55011 FOR EMISSION; APPROVAL:CCOE/PESO AND CMRI: FOR RTD AND TRANSMITTER IS IN ATTACHED DATA SHEET

SPLY OF 24" MOV AT OR — VALVE ,MOV; NOMINAL SIZE:600 MM; DESIGN SPEC,PRESSURE RATING:CLASS 150; TYPE OF END CONNECTION:FLANGED; MATERIAL,BODY:CARBON STEEL; SCHEDULE/WALL THICKNESS:N/A; DESIGN SPEC:API SPEC 6D; SERVICE:MS/HSD/SKO; MAT,TRIM:N/A; MAT,SEALS:GRAFOIL; MAT SPEC,BODY:ASTM A216 GRADE WCB; MAT SPEC,BONNET:ASTM A216 GRADE WCB; MAT SPEC,STEM:AISI 4140; MAT SPEC,BOLTS/STUDS:ASTM A193 GRADE B7; MAT SPEC,NUT(S):ASTM A194 GRADE 2H; TYPE, VALVE:DOUBLE BLOCK AND BLEED AND DOUBLE ISOLATION; MAT SPEC, BODY:ASTM A516 GRADE 70 / ASTM A216 GRADE WCC; MAT SPEC, BONNET:ASTM A516 GRADE 70 / ASTM A216 GRADE WCC; MAT SPEC, GATE/SEGMENT/PLUG:ASTM A216 GRADE WCC / WCB OR ASTM A516(ENP); MAT, SEAT SEAL:VITON(DUPONT/3M); MAT, O-RING SEAL:VITON GFLT; MAT SPEC, END FLANGE:ASTM A105; FINISH, FACING FLANGE:125 AARH; MOTOR OPERATED ACTUATOR REQUIREMENT:YES

SPLY OF 24" MOV AT SS — VALVE ,MOV; NOMINAL SIZE:600 MM; DESIGN SPEC,PRESSURE RATING:CLASS 150; TYPE OF END CONNECTION:FLANGED; MATERIAL,BODY:CARBON STEEL; SCHEDULE/WALL THICKNESS:N/A; DESIGN SPEC:API SPEC 6D; SERVICE:MS/HSD/SKO; MAT,TRIM:N/A; MAT,SEALS:GRAFOIL; MAT SPEC,BODY:ASTM A216 GRADE WCB; MAT SPEC,BONNET:ASTM A216 GRADE WCB; MAT SPEC,STEM:AISI 4140; MAT SPEC,BOLTS/STUDS:ASTM A193 GRADE B7; MAT SPEC,NUT(S):ASTM A194 GRADE 2H; TYPE, VALVE:DOUBLE BLOCK AND BLEED AND DOUBLE ISOLATION; MAT SPEC, BODY:ASTM A516 GRADE 70 / ASTM A216 GRADE WCC; MAT SPEC, BONNET:ASTM A516 GRADE 70 / ASTM A216 GRADE WCC; MAT SPEC, GATE/SEGMENT/PLUG:ASTM A216 GRADE WCC / WCB OR ASTM A516(ENP); MAT, SEAT SEAL:VITON(DUPONT/3M); MAT, O-RING SEAL:VITON GFLT; MAT SPEC, END FLANGE:ASTM A105; FINISH, FACING FLANGE:125 AARH; MOTOR OPERATED ACTUATOR REQUIREMENT:YES

INSTLN, COMM OF 24" MOV — INSTALLATION OF CL150 18 INCH SIZE MOV. JOB INCLUDES TAKING OVER VALVES FROM STORE HOUSE, HAULING, SHIFTING TO DESIGNATED PLACE, SERVICING/OPENING/TIGHTENING OF NUTS/BOLTS, HANDLING, LIFTING (USING CRANES). SUPPLYING AND FIXING OF ALL STUDS/NUTS/BOLTS OF APPROVED MAKE (CONFORMING TO ASTM A193 B7 AND A194 2H), LENGTH, SIZE AND DIAMETER WITH WASHERS COMPLETE AND SPIRAL BOUND GRAPHITE FILLED METALLIC GASKET OF APPROVED MAKE FOR BOTH FLANGED ENDS OF THE VALVE. ALL TOOLS,TACKLES, MANPOWER, PPE, CONSTRUCTION SAFETY, SUPERVISION TO CARRY OUT JOB AS PER SITE CONDITION AND DIRECTION OF HPCL.

INSTLN, COMM OF 24" MOV SS 11992-Visakha New Terminal — INSTALLATION OF CL150 18 INCH SIZE MOV. JOB INCLUDES TAKING OVER VALVES FROM STORE HOUSE, HAULING, SHIFTING TO DESIGNATED PLACE, SERVICING/OPENING/TIGHTENING OF NUTS/BOLTS, HANDLING, LIFTING (USING CRANES). SUPPLYING AND FIXING OF ALL STUDS/NUTS/BOLTS OF APPROVED MAKE (CONFORMING TO ASTM A193 B7 AND A194 2H), LENGTH, SIZE AND DIAMETER WITH WASHERS COMPLETE AND SPIRAL BOUND GRAPHITE FILLED METALLIC GASKET OF APPROVED MAKE FOR BOTH FLANGED ENDS OF THE VALVE. ALL TOOLS,TACKLES, MANPOWER, PPE, CONSTRUCTION SAFETY, SUPERVISION TO CARRY OUT JOB AS PER SITE CONDITION AND DIRECTION OF HPCL.

PREFABRIC_SKID_MS_OR — ELIMINATOR; TYPE:VAPOUR; MATERIAL:N/A; PRESSURE RATING:FLANGE RATING; FLOW RATE:0.3 KG/CM2; SIZE:N/A; NOZZLE SIZE, INLET:PIPELINE SIZE; NOZZLE SIZE, OUTLET:PIPELINE SIZE; DESIGN PRESSURE:10 KG/CM2G;HYDROTEST PRESSURE:15 KG/CM2G; DESIGN TEMPERATURE:65 DEG C; RETENTION TIME REQUIRED:5 SEC; EFFECTIVE PRODUCT VOLUME TO BE MAINTAINED BETWEEN INLET NOZZLE AND OUTLET NOZZLE DYNAMICALLY BETWEEN INLET NOZZLE RETETION TIME REQUIRED:AS A MINIMUM EFFECTIVE VOLUME SHALL BE EIGHT PERCENTAGE OF MAXIMUM FLOW RATE SPECIFIED IN LPM. NOTE: REFER DIRECTIVE OF EUROPEAN COUNCIL 77-313-EEC STATING REQUIREMENTS OF MEASURING SYSTEMS FOR LIQUIDS OTHER THAN WATER" FOR SIZING OF VAPOUR ELIMINATOR. NOTE: OEMS OF MFMS ARE ALLOWED TO OFFER HIGHER SIZE VAPOUR ELIMINATORS TO ENSURE PROPER PERFORMANCE OF THEIR MFMS AT SITE; SEPARATION OF AIR/VAPOR; VESSEL DESIGN CODE:ASME SEC VIII DIV. 1- 2010; VESSEL DESIGN CODE:ASME SEC VIII DIV. 1- 2010; RADIOGRAPHY:FULL AS DEFINED IN ASME SEC VIII DIV; CORROSION ALLOWANCE:3 MM; NOZZLE AND ACC/NOZZLE CONFIGURATION; COVER:8 INCH NPS BOLTED COVER; DRAIN:NPS CLASS 150; VENT:3/4 INCH NPS CLASS 150; TRV:TRV CLASS 150; AIR VENT O/L:1 INCH NPS CLASS 150; DETAILS OF AIR VENT AND COUNTER WEIGHT; TYPE;PILOT AND FLOAT WITH COUNTERWEIGHT; MOC:BODY/INTERNAL/SEAL CS/SS316/VITON; LOCATION OF AIR VENT:INTERNAL; MATERIAL SPECIFICATIONS OF COMPONENT; SHELL:SA 516 GR. 70N/SA 106 GR. B; DISHED ENDS (BTM):SA 516 GR. 70N/SA 234 WPB; BODY COVER/QOC:SA 105N / SA 516 GR. 70N; FLANGES:SA105; NOZZLE PIPES:SA 106 GR.B; STUD-NUTS:SA 193 B7/SA 194 GR.2H; GASKETS/SEALS:SP. WD SS304 W PTFE/NYLON 6; AIR VENT:SS316+VITON SEAL; VESSEL SUPPORTS:IS: 2062-A/IS:226; PAINTING:1 COAT OF ZINC PHOSPHATE PRIMER + 1 COAT OF HI-BUILD MIO + 1 COAT OF POLYURETHANE PAINT TOTAL DFT, 150 MICRON; THIRD PARTY INSPECTION:BY HPCL APPROVED AGENCY; MAKE:FLASH POINT/TOSHNIWAL (I) PVT.LTD/CRYOGENIC/LIQUID CONTROLS; TYPE:VERTICAL CENTRIFUGAL GAS SEPARATOR WITH PILOT AND FLOAT TYPE AUTOMATIC VENT

PREFABRIC_SKID_HSD_SS — ELIMINATOR; TYPE:VAPOUR; MATERIAL:N/A; PRESSURE RATING:FLANGE RATING; FLOW RATE:0.3 KG/CM2; SIZE:N/A; NOZZLE SIZE, INLET:PIPELINE SIZE; NOZZLE SIZE, OUTLET:PIPELINE SIZE; DESIGN PRESSURE:10 KG/CM2G;HYDROTEST PRESSURE:15 KG/CM2G; DESIGN TEMPERATURE:65 DEG C; RETENTION TIME REQUIRED:5 SEC; EFFECTIVE PRODUCT VOLUME TO BE MAINTAINED BETWEEN INLET NOZZLE AND OUTLET NOZZLE DYNAMICALLY BETWEEN INLET NOZZLE RETETION TIME REQUIRED:AS A MINIMUM EFFECTIVE VOLUME SHALL BE EIGHT PERCENTAGE OF MAXIMUM FLOW RATE SPECIFIED IN LPM. NOTE: REFER DIRECTIVE OF EUROPEAN COUNCIL 77-313-EEC STATING REQUIREMENTS OF MEASURING SYSTEMS FOR LIQUIDS OTHER THAN WATER" FOR SIZING OF VAPOUR ELIMINATOR. NOTE: OEMS OF MFMS ARE ALLOWED TO OFFER HIGHER SIZE VAPOUR ELIMINATORS TO ENSURE PROPER PERFORMANCE OF THEIR MFMS AT SITE; SEPARATION OF AIR/VAPOR; VESSEL DESIGN CODE:ASME SEC VIII DIV. 1- 2010; VESSEL DESIGN CODE:ASME SEC VIII DIV. 1- 2010; RADIOGRAPHY:FULL AS DEFINED IN ASME SEC VIII DIV; CORROSION ALLOWANCE:3 MM; NOZZLE AND ACC/NOZZLE CONFIGURATION; COVER:8 INCH NPS BOLTED COVER; DRAIN:NPS CLASS 150; VENT:3/4 INCH NPS CLASS 150; TRV:TRV CLASS 150; AIR VENT O/L:1 INCH NPS CLASS 150; DETAILS OF AIR VENT AND COUNTER WEIGHT; TYPE;PILOT AND FLOAT WITH COUNTERWEIGHT; MOC:BODY/INTERNAL/SEAL CS/SS316/VITON; LOCATION OF AIR VENT:INTERNAL; MATERIAL SPECIFICATIONS OF COMPONENT; SHELL:SA 516 GR. 70N/SA 106 GR. B; DISHED ENDS (BTM):SA 516 GR. 70N/SA 234 WPB; BODY COVER/QOC:SA 105N / SA 516 GR. 70N; FLANGES:SA105; NOZZLE PIPES:SA 106 GR.B; STUD-NUTS:SA 193 B7/SA 194 GR.2H; GASKETS/SEALS:SP. WD SS304 W PTFE/NYLON 6; AIR VENT:SS316+VITON SEAL; VESSEL SUPPORTS:IS: 2062-A/IS:226; PAINTING:1 COAT OF ZINC PHOSPHATE PRIMER + 1 COAT OF HI-BUILD MIO + 1 COAT OF POLYURETHANE PAINT TOTAL DFT, 150 MICRON; THIRD PARTY INSPECTION:BY HPCL APPROVED AGENCY; MAKE:FLASH POINT/TOSHNIWAL (I) PVT.LTD/CRYOGENIC/LIQUID CONTROLS; TYPE:VERTICAL CENTRIFUGAL GAS SEPARATOR WITH PILOT AND FLOAT TYPE AUTOMATIC VENT

SPLY BULK AIR — BULK AIR ELIMINATOR AS PER ATTACHED SPECIFICATIONS.

SPLY BULK AIR — BULK AIR ELIMINATOR AS PER ATTACHED SPECIFICATIONS.