Renovation of Chamber of Dean at College of Horticulture and Forestry Neri- Hamirpur.

Amount

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing Sal wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 250x16 mm (two hundred fifty into sixteen milimetre)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 200x10 mm(two hundred into ten milimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 125mm

Providing and laying Glossy vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, (Kazaria/ Nitco/ Orient bell make), in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete complete in all respect as per satisfaction of Engineer-in-Charge.a). Size of tile 600x600mm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade etc. all complete as specified and as directed by the Engineer-in-Charge. a)Two or more coats on new work

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge. a).With cement mortar 1:4 (one cement : four sand)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within all leads etc. complete as per direction of Engineer-in-charge. a). In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all leads etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Area 3 sq. metres and below.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within all leads etc. all complete as specified and as directed by the Engineer-in-Charge a). For thickness of tiles 10mm to 25mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately).

a). Anodised Aluminium ( anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of grade AC 15 for fixed portion.

b). .Anodised Aluminium ( anodized transparent or dyed to required shade according to IS: 1868 minimum anodic coating of grade AC 15 for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing 12mm thick prelaminated particle boardwith decorative lamination on both side flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete complete in all respect as per satisfaction of Engineer-in-Charge(Actiontesa/ Green ply make).

Providing and fixing false ceiling at all heights with integral densified calciumsilicate reinforced with fibre and natural filler false ceiling tiles of Size595x595 mm of approved texture, design and patterns having NRC (NoiseReduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Lightreflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fireperformance as per BS:476 (part 6 &7), humidity resistance of 100%, thermalconductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal levelsuspended on interlocking metal T-Grid of hot dipped galvanised iron sectionof 0.33mm thick (galvanized @ 120 grams per sqm including both sides)comprising of mainT runners of size 24x38 mm of length 3000 mm, cross - Tof size 24x32 mm of length 1200 mm and secondary intermediate cross-T ofsize 24x32 mm of length 600mm to form grid module of size 600 x 600 mm,suspended from ceiling using galvanised mild steel items (galvanizing @ 80grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partitionwith the help of plastic rawl plugs at 450 mm center to center and 40 mm longdry wall S.S screws. The work shall be carried out as per specifications,drawing and as per directions of the Engineer-in-Charge.

a). With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable complete in all respect as per satisfaction of engineer-in-charge. Group - C

Wiring for light plug with 2x 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required complete in all respect as per satisfaction of Engineer-in-charge.

a). 2 modules (78 mm. x78 mm. x50 mm.)

b). 6 module (205 mm x 78 mmx50 mm.)

Supplying and fixing following rating modular switch/socket in the existing switch box/cover plate including connections etc. as required complete in respect as per satisfaction of engineer-in-charge

a). S.P. 5/6 Amps one way Modular switch.

b). S.P. 15/16 Amps one way Modular switch

c). 5 pin, 5/6 Amps Modular socket outlet

d). 6 pin, 15/16 Amps Modular socket outlet

e). Telephone socket outlet, modular

Supplying and fixing socket type modular fan regulator on the existing modular box including making connection etc. as required complete in all respect as per satisfaction of Engineer-in- charge.

Supplying and fixing ceiling rose on the existing junction box/wooden block including connections etc. complete in all respect as per satisfaction of Engineer-in-charge.

Supplying, installation, testing and commissioning of indoor lighting LED luminaire surface Type a size of 2’-0’ into 2’-0” and wattage 36 watt IP 20 rating CRCA body PS diffuser complete in all respect as per satisfaction of Engineer–in- charge (Panasonic/Great white/ jaguar/Bajaj Make).

Providing and fixing 12 mm thick imported pine wood paneling/lining & ceiling with tongued and grooved jointing and wooden screws etc. complete in all respect as per satisfaction of Engineer-in- Charge (Frame work to be measured and paid for separately).

Polishing two coats with melamine polish of required shade on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 3 seater sofa with Overall Size: Width: 171cm Depth: 86cm Height: 77cm Seating Height: 39cmFrame material: tropical solid wood, Seat foam: polyurethane foam with recron layer. Foam density: 18 kg/ cubic cm. Back foam: polyurethane foam with silicon fill At arms. Foam density: 22 kg/cubic cm etc. complete in all respect as per satisfaction of Engineer-in-Charge. (Godrej /Kotterman/ HNI/Waldner Make)

Providing and fixing High Back Chair with Cushioned seat made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. High BACK SIZE: 47.7 cm. (W) x 76.4 cm. (D) The armrest top is moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: 360’ revolving type.Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort.Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair.Seat/back tilting ratio of 1: 2The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. Pitch-center dia.(75.0 ± 1.0cm. With castors (W)76.1*(D)76.1*(H)112.7-130.2 Seat Height 43.1-53.1cm etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Godrej /Kotterman/ HNI/Waldner Make)

Providing and fixing Visitor Chair with SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) BACK SIZE : 45 cm. (W) x 60.5 cm. (D) Visitor TUBULAR FRAME: The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube.The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece. Overall Dimensions of Chair Seat Height - 44.8cm. Height - 99.5cm. Width-60.9 cm and Depth-64.3 cm etc. complete in all respect as per satisfaction of Engineer-in-Charge. (Godrej /Kotterman/ HNI/Waldner Make)

Anil Jaswal