ADDN/ALTN AND UPGRADATION OF 18 QTRS OF JCOS MD ACCN, 72 QTRS OF OR MD ACCN AT SHEKHAWATI LINE AND 16 JCOS, 33 OR MD ACCN AT NPG LINE AND 28 OR MD ACCN AT HAZIPIR LINE UNDER GE(WEST) DELHI CANTT-10

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not other specifically provided for complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed.

Demolition of mud phuska on roof slabs, any thickness including cleaning of roof surfaces removal of debris up to 1.50 km complete all as specified and directed.

Scraping of old tar felt roof treatment over concrete padding of any thickness etc from roof including finishes or junction or parapet and cleaning the surface completely all as specified and directed.

M&L for providing Cement concrete 1:5:10 in filling of sunken portion type E2 using 40mm graded aggregate.

M&L for providing cement concrete 1:2:4 type B-I 20mm graded in roof kerb or mud slops, rounded or chamfered on edges, complete including necessary form work all as specified and directed.

M&L for cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) on roof padding with water proofing compound surface finished even and smooth without using extra cement complete all as specified and directed. (Note : Supply only WPC shall be measured and paid separately )

M&L for 40mm thick brick tiles bedded in cement mortar (1:6) 15mm thick and jointed and grouted flush in C:M 1:3 mixed with 5% crude oil by weight of cement complete all as specified and directed.

All as per item No.8 above but except brick tiles. Note : - Old retrived servicable tiles shall be used under ths item.

Demolition of cement concrete (reinforced) of any description and as in kitchen shelves etc not other specifically provided for complete and removal of debris outside MoD land all as specified and directed. Note :- Dismantling existing RCC work at all heights including disposal of unserviceable material within a lead of 50 metre, using chisel and hammer or Mechanically using power driver/pneumatic percussion chisels/hammers with all labour consumables, tools, plants, propping, scaffolding, safety arrangement, quality control and checking complete also providing necessary Props (Ground floor, first floor and third floor) before demolition of RCC slab or other activities as directed by Engineer-in-charge.

M&L providing pre cast cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in Kitchen slab, passage roof etc and set in cement mortar 1:4 complete all as specified & directed.

M&L for TMT bars 8mm dia and above cut to length bent to shape required including cranking, bending etc and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified & directed.

Demolition of brick work built in cement /lime mortor in any position / situation in walls/parapets complete and removal of debris outside MoD land all as specified and directed.

M&L for brick work with class 'A' bricks (awwal), straight or curved on plan exc. 6 mtr mean radius built in cement mortor 1:6 complete all as specified and directed.

M&L for half brick work with class 'A' bricks (awwal), straight or curved on plan to any radius built in cement mortor 1:4 complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections all as specified and directed.

All as per item No. 16 above, but 20mm bore.

All as per item No. 16 above, but 25mm bore.

All as per item No. 16 above, but 40mm bore.

M&L 15mm bore GI tubing, medium grade, with all fittings and fixed complete to walls, ceiling or laid in floor.

All as per item No. 20 above but 20mm bore tubing.

All as per item No. 20 above but 25mm bore tubing.

All as per item No. 20 above but 40mm bore tubing.

Dismantling of PVC water storage tanks exc 250 & n.exc 500 ltrs double layer capacity and removing from site all as specified.

S&F rotational moulded polythylene water storage tanks 500 Ltrs capacity double layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified in SSR part I and directed.

All as per item No. 25 above, but execpt tank.

Taking down cement or cement lime plaster on walls and ceiling incl racking out joints, hacking for keys, scrubbing down with water etc all as specified.

M&L for ready mix plaster 15mm thick on fair faces of brick work or concrete surfaces of walls and finished even and smooth complete all as specified.

M&L for ready mix plaster 5mm thick on ceiling surfaces of any description, finished even and smooth all as specified.

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, Internal 75mm dia of pipe 100mm complete all as specified & directed.

Dismantling 75mm dia of cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified & directed.

S&F 100mm bore cast iron spun soil waste or vent pipes in any length with or without ears with lead joints fixed to walls complete all as specified and directed.

All as per item No. 31 above but 75mm bore of pipe. Note : Applicable to Srl item No 32 & 33 :- lead joint shall be mesured and paid seperatly under respective items.

S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and dfirected.

S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and dfirected.

S&F 100mm bore cast iron bends (any radius) diminishes pieces or taper complete all as specified and directed .

All as per item No.36 above but 75mm bore of pipe.

S&F CI 100mm bore Tee with oval access door, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches including oval access door all as spd & directed.

All as per item No. 38 above but 75mm bore of pipe.

S&F 75 bore cast iron bend with oval access door

S&F CI Cowl for 100 mm bore of CI pipe.

S&F CI Cowl for 75 mm bore of CI pipe.

S&F in repairs 10 ltrs capacity PVC valveless syphonic action type low level flushing cistern complete with syphone handle lever PVC bend including connecting to WC and fixing on walls with suitable size of angle iron bracket complete all as specified and directed.

S&F in repair vitreous china water closet Orissa type 580 x 440 mm white with integral foot rests including provn of lime concrete bedding including connections to flushing cistern pipe and making good disturbed portion to match existing surfaces complete all as directed including 'P' or 'S' trap of cast iron.

S&F vitreous china wash hand basin (flat black) white of size 550x400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size complete all as specified.

S&F in repairs 75mm dia CI floor trap with grating jointing with lead joint to waste pipe including cement concrete type B-1 (1:2:4) floor around to required depth and burning lead joints etc to facilitate dismantling old CI trap and making good complete all as directed.

Taking down wooden/steel chowkhats/door/window frame including shutter (without taking off shutter from frame) exc 1.5 Sqm and n.exc 4 Sqm each complete all as specified and directed.

Taking down wooden/steel chowkhats/door/window frame including shutter (without taking off shutter) not exc.1.5 Sqm each complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm and not exc 2.00 Sqm complete all as specified and directed.

Taking down shutter of any description not exc 1.00 Sqm complete all as specified and directed.

S&F mild steel framed work as in door or gates of angle or other sections, with gusset plates rails, braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and including either hooks and purpose made hinges or steel sheeting or other covering, running rails and guides) and hanging, fastening and fixing complete conforiming to Fe 290 Gde E-165.

Cutting holes (exceeding half brick wall but not exceeding one brick walls) built in cement mortar or cement lime mortar and stone walls built in lime mortar complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood plain framed panelled door shutter two pannels with lock rail and panel of 9 mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces .The size of rail and style as per IS1003 part I kiln seasonned chemically pressure treated complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkat complete all as specified and directed.

S&F factory made 35mm thick flush shutters, solid core construction, with block board core and plywood face panels commercial type covered with decorative face veneer with lipping/ frame to match all as specified and directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S.square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded pre-laminated PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement and provision of partially louvered frame supply and fixing in the frame at site. Complete all as per specification & sample kept in GE office and as directed.

M&L for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apperture 1.40 mm fixed to door/window frame complete all as specified and directed.

S&F butt hinges 100mm size, medium weight cold rolled mild steel and fixed to angle iron /steel chowkhat complete all as specified and directed.

S&F 100mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed.

S&F aluminium anodised barrel tower bolt, extruded section 200mm size.

S&F aluminium anodised Handles cast type for 150mm size.

S&F aluminium anodised Handles cast type for 100mm size.

S&F aluminium anodised barrel tower bolt, extruded section 100mm size.

S&F 300mm aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 4.8mm thick figured glass/ pin head type and glazing with oil putty in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 100 mm hasp and staple, aluminium Including bolt to hinges plate and fixed with screws all as specified and directed.

M&L for Preparation of new surfaces of wood or wooden base surface of any description not otherwise described over 10cm width or grith and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

All as per item No. 66 above but on steel surfaces over a coat of redoxide primer.

M&L for Preparation of old wooden surfaces of any description not otherwise described over 10cm width or grith and applying one coat of synthetic enamel paint complete all as specified.

All as per item No. 71 above but one coat of paint on old steel surfaces.

Complete removal of existing treatment of walls by scrapping with mechanical grinders complete all as specified.

M&L for 1 mm thick wall care puttty on wall finished even and smooth complete all all as specified and directed.

M&L for two coats of oil bound distemper over one coat of alkali resistant primer including preparation of new pastered surface surfaces complete all as specified.

M&L for two coats of oil bound distemper over one coat of alkali resistant primer over 1mm thick wall care putty and complete all as specified and directed.

M&L three coat of white washing on newly plastered surfaces of walls including preparation of surfaces.

M&L two coats of white washing on old plastered surfaces including prepration of surfaces of walls complete all as specified and directed.

M&L three coat of white washing on newly plastered surfaces of ceiling including preparation of surfaces.

M&L two coats of white washing on old ceiling surfaces including prepration of surface complete all as specified and directed .

Dismantling floor, hearth or wall tiling including cement mortar bedding removing serviceable tiles to store and rubbish off the premises.

M&L for 18 to 20mm thick, granite (of any type) work (table rubbed and polished) in window-cills, cooking platforms and like in 15mm tihck cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including hole for gas pipe etc and rounded edges of exposed edges complete all as directed.

M&L for non skid colour ceramic rectified tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.06Sqm but not exceeding 0.11Sqm, in floors etc, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L for coloured printed glazed ceramic tiles of size 350x 250x 7 mm/ 450X 350X 7mm on vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white/ coloured cement, laid over and including cement screed bed 10mm thick in cement mortar 1:4, complete all as specified.

M&L for non skid colour ceramic rectified joint free tiles 7-8 mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set jointed in neat cement slurry & pointed in coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

S&F in repair stainless steel tubular towel rail 20mm dia, D type 60 cm long between flanges, complete all as specified and directed.

S&F curtain rails of MS pipe with PVC coating with fixing brackets stops and decorative finials etc complete all as specified and directed.

S&F sink made of stainless steel 1mm thick for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall including fixing cantilever, brackets and connecting union to pipe over all size 495 x 420 mm, bowl size 410 mm x 330 mm x 160mm complete all as specified and directed.

S&F stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste coupling and waste pipe, cast iron cantilever brackets, connecting union over all size 915mm x 460mm with bowl size 410mm x 330mm x 160mm complete all as spd and directed by Engr-in-Charge.

S&F in repairs 15mm dia bib tap fancy type brass with capstan head chromium plated screwed down high pressure with long screwed shank and flynut screwed completeall as specified.

S&F in repairs 15mm dia chromium plated bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repairs 15mm bore stop valves/angle valves, cast copper alloys, fancy type chromium plated, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spd and directed.

S&F in repairs 20mm bore of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repairs 40mm bore of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F in repairs 25mm bore of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

S&F PVC connection 450mm long with 2 Nos brass check nuts, suitable for 15mm bore complete all as specified and directed.

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminum rod and high density polythene float and flynut complete, screwed for iron pipe or brass furrule size 20mm bore. (Min weight 210gms complete all as directed)

S&F in repairs shower rose, chromium plated brass, fancy type, 125 mm with or without swivel joint, any size, including fixing to steel pipe or union, complete all as directed.

S&F factory made 25mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides as shutter of cupboard complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floor or in any position laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut Kota stone slab 20 mm thick as in treads, risers of staicase laid over cement screed bed 15mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing kota stone in treads and risers should be in single piece and rounded edges of exposed edges complete all as specified and directed.

S&F stainless steel kitchen plate rack made out of stainless steel sheets 1mm thick overall size 600mm x 750mm x 250mm including coupling, waste pipe and suitable size of angle iron bracked complete all as specificed and directed.

M&L for 12mm thick WPC board solid flush type colour plain white fixed with necessary screws,solvent cement/adhesive to make kitchen cabinet back covering etc complete all as specified and directed.

M&L for teak wood lipping, 6mm thick fixed with nails to 18mm thick veneered particle borad including polishing complete all as specified.(Note: veneeral particle board shall be measured and paid seprated)

S&F of autoclosing hinges openable at 0 degree for kitchen cabinet shutters all as specified and directed.

S&F continouious (piano) hinges width of flap 40 mm mild steel bright finish complete all as specified.

S&F of stainless steel handles 100mm size for kitchen cabinet shutters all as specified and directed.

S&F 40 mm dia cup board knobs fixed with nut, screws and wahers of brass polish complete all as specifeid.

S&F ball catches with 8mm dia steel ball and brass body and sinking plate with overall 150mm length of cover plate including letting in and fixed complete all as specified

M&L for providing 40mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate admixed with integral WPC complete all as specified finishing cement concrete surface even and smooth w/o using extra cement. Note: Water proofing compound shall be measured and paid sepretaly.

M&L for protection plaster 15mm thick on cement mortar 1:3 admixed with appropriate integral water proofing compound complete all as specified. (Note : Supply only WPC shall be measured and paid separately)

M&L for providing 40mm dia GI pipe spout projecting at least 150mm beyond outer face of wall

M&L for glass fibre reinforced acrylic modified cementious coating system with base coat of Sika Top @ Seal 107 or equivalent @ 1.50 Kg/Sqm fibre reinforcement Sika ® Fab-1 and top coat with Sika Top® Seal-107@ 1.50 Kg/Sqm or equivalent of FOSROC or PIDILITE complete all as specified and directed

S&F framed work such as grills, grating etc. with ends of bars shouldered and /or riveted , or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar works conforming to Fe290. Gde-E-165 complete all as spd & directed. Note : Provision of openable arrangement for placing coolers on stand shall be made in window grill wherever required.

Supply only Integral waterproofing compound.

S&F powder coated (with minimum thickness of 50 micron) aluminium frame for windows, ventilators and sliding tracks, beading for grill with one or more rebates including jointing ccleat for fixing etc complete all as specifed and directed by Engineer in Charge.

S&F powder coated (with minimum thickness of 50 micron) aluminium window and ventilator shutters, side hung type with/ without sash bars, aluminium sections weighing 0.45 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21, 100mm long (2 Nos) suitable handle (1 No) complete all as specified and directed.

S&F powder coated(minimum thickness of powder coating 50 micron) aluminium section for shutters suitable for three/four track window and aluminium sections weighing more than 0.45kg/m of sliding members incl all necessary fittings and fixtures, jointing cleats, rubber packing etc complete all as specified and directed.

M&L for preparation of old treated brick/plastered surfaces of walls upto 4th storey height by scrubbing with wire brush, hard brush, washing down with water and applying two coats of cement paint, white or tinted including one coat of primar complete all as specified & directed.

M&L for preparing new plastered surfaces of wall upto 4th storey height and applying two coats of cement paint, white or tinted including one coat of alkali resistant primar complete all as specified & directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified & directed.

Taking down wooden door shutter exc 1.00 Sqm and n. exc 2.00 Sqm each and refixing in same opening complete all as specified & directed

Supply only CP waste coupling 32 mm size with PVC waste pipe, plugs and washers for WHB complete all as specified & directed.

Supply only CP waste coupling 40 mm size with PVC waste pipe, plugs and washers for kitchen sink complete all as specified & directed.

S&F cromium plated peg set of size 175 mm to 250 mm complete all as specified and directed

All as per item 128 above but of size 125 mm to 175 mm

S&F of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring including vulcanised rubber piece of 140 mm long.

M&L for use & waste of form work using steel sheets , steel bracing, propping etc around structural members where micro concreting to be done and keeping form work in position till required specified period complete all as specified and directed. Note : Form work shall be 100% leak proof. For purpose of payment area in touch with concrete shall be measured.

M&L for keyed pointing to brick walls in cement mortar 1:4 complete all as specified and directed upto 4th story.

S&F PVC (SWR) 50 mm bore rain water pipes single socketed in any length with rubber ring joints, laid in trenches or in floors.

S&F PVC (SWR) bends 50 mm bore complete all as specified and directed.

Impregnating cream for injection into masonary or concrete wall 230mm thick against capilary rising humidity. Rising bar super strong (Product no. 201) of chowgale building chemicals or equivalent pidlite/Drfixit/sika/phosrock complete all as specified and directed Method of Application Methodology (a) The surface must be sound , absorbent, clean, free of dust, oil, paint, curing agents , loose cement or lime plaster & concrete, debris, or any separation layers. (b) The plaster must be knocked off at least 50cm beyond the visibly penetrated area. (c) Damaged mortar joints are to be scraped out to a depth of approximately 2-3 cm. All sharp edges/joints need to be levelled ; loose concrete to be removed. (d) Drill boreholes at ground level horizntally. The boreholes are drilled horizontal into the masonry. (e) The holes should be drilled until a depth of approx 5cm (for a 6cm thick wall) before the end of the wall is reached. The boreholes should have a diameter of 12mm upto a maximum of 15mm and should be spaced approx 100-120mm apart and the vertiacal offset is 6cm maximum (f) Before inserting rising bar super strong or equivalent the boreholes must be clean from boring dust by using air pressure. It is not necessary to pre-wet the boreholes. (g) For applying of rising bar of super strong or equivalent the dosing system inserted as far as possible into the bore holes. While dosing the product uniformly, the injection nozzle is pulled out leading to a completely filled boreholes (h) Treatment of highly absorbent masonary mught required repeated filling of the boreholes. depending upon extent of damage, rising bar superstrong or equivalent can be re-injected into the same hole after 24 hrs. depending on observency, application or masonry thickness 0.1 to 0.15 ltr/m with 10cm wall thickness.

M&L for providing and injecting chemical emulsion for post construction anti-termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 ltr/sqm of the vertical surface of the sub-structure to a depth of 300mm incl excavating channel along the wall and rodding etc complete.

M&L for treating of soil under existing floor using emulsion at the rate 1 ltr/hole, 300mm apart incl drilling and plugging 12mm dia. Holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floor.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade laid over 25mm thick sand cushion with grey cement and pigment complete all as specified and directed. (Note : Sand filling to be measured and paid seperately)

M&L for sand filling under floors for cushion bed to interlocking paver block all as specified and directed.

S&F in repair PVC (SWR) bends 110 mm bore complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm bore rain water pipes single socketed in any length with rubber ring joints fixed to walls incluiding taking down complete all as specified and directed.

S&F brass CP wall mixer non telephonic type for mixing hot and cold water for shower screwed down for 15mm brass iron pipe or ferrul of complete all as specified & directed.

S&F Swan neck centre hole basin mixer 15 mm, CP with capstan heads, screwed down high pressure, screwed for iron pipe and fixed all as specified and directed.

M & L for Rough cast cement plaster with mixture consisting of crushed stone or fine gravel aggregate of 6 to 12 mm size mixed with coarse sand and cement in the ratio of 1:1:1 over a back coat of 10 mm thick rendering in CM 1:4 on walls surface finished to recieve rough cast cement plaster even and smooth without using extra cement incl taking down cement or cement lime plaster on walls incl racking out joints, hacking for keys, scrubbing down with water etc complete all as spd and directed.

Refixing of balconey grill without damage including welding, cleaning rust and apply zink priper and fixing same place without any damage to existing structure etc complete all as specified and directed by Engr-in-Charge. Note : Removing all balcaney grill up to 4 storey building without any damage and refixing same place. The cost of refing is included in this item.) .

M&L for lead joint provided for 100 mm dia CI pipecomplete all as specified and directed.

M&L for lead joint provided for 75 mm dia CI pipe complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr wide and n exc 1.5 mtr depth for foundation etc not exc 10 Sqm on plan and getting out in soft and loose soil complete all as specified and directed.

Returning filling in soft/loose soil spreading leveling watering and well ramming in layers n exc 25 cm thick complete all as specified and directed.

Removing of surplus soil to a distance exc 250 mtr but not exc 500 mtr and deposited where directed as a level n .exc 1.5 mtr above the starting point complete all as specified.

M&L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick laid in bays and surfaces finished even and fair including filling the joints with bitumen mastic complete all as specified and directed.

PMM repairs (FOR PATCH REPAIRS)

(a) 25-30 mm average thickness ( in 2 layers)

(b) 50-60 mm average thickness ( in 3 layers )

PMM repairs at (a) and (b) above shall be done as per following methodology (From sub items (i) to (vi) below)

i) Chipping of plaster and unsound/weak concrete material till reinforcement bars are exposed, which enabls their rust removal vides item ii) below, from slabs, beams, and columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-incharge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads .

ii) ) Rust removal by Providing and applying Fosroc Reebaklens RR or equivalnet from SIKA/ BASF, a combination of acid based material, corrosion inhibitors and dispersing agents rust remover, for removal of all rust/ scales/corrosion from reinforcement bars before microconcreting or patch repair,It Shall be applied with brush for complete wetting of rusted metal surface at coverage of 2- 2.5 Sqm/ltr. & allow it to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal /steel for about 5-7 days. Before applying any protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.

iii) Anticorrosive treatment by Providing and applying Nitozinc Primer an epoxy based zinc rich anti corrosive primer having adhesive bond strength ≥ 1.5 MPa as per ASTM D4541, & shall comply to per ASTM B-117 to be applied on well cleaned, fully exposed and all loose scale , rust free rust free surface obtained by grit blasting or suitable means , to be done with coverage @4.5sqm/litres to achieve a minimum thickness of 40microns DFT or as per direction of Engineer-In charge.

(iv) (a) Applying epoxy bond coat on the sound concrete substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (b) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.

v) PMM by providing and laying single component, polymer modified, fibre reinforced cementitious repair mortar, Rendroc SP40 or equivalent from SIKA/BASF over the tacky bond coat, that achieves Compressive strength (BS 1881 Pt.116) > 20 MPa at 1 day , > 45 Mpa at 28 days, Tensile Strength > 2.5MPa, Flexural Strength > 7Mpa at 28 days, Finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slabs, piles etc., , complete in all aspect as per manufactur's methodology. Rates include cost of all labour, materials, Tools and Plants,propping, scaffolding, shuettering, safety arrangment, quality control, testing complete as per specifications and direction of engineer in charge.

vi) Item rates of PMM 25 mm and PMM 50 mm (against items (a) and (b) respectively ) are inclusive of all materials, labour, tools and plants, propping, scaffolding, safety arrangement, quality control, testing and all items of works from i) to v) above quality control etc. complete in all respect, as per specifications and as directed by Engg.-in-charge. Work shall be complete only after proper wet curing has been done by contractor and surface has been evaluated for satisfactory quality by sounding/tapping with a blunt metal instrument, and testing of PMM cubes filled up and cured by contractor during the application of PMM (75mm size cube crushing strength at the end of 28-day to be not less than 45 N/sqmm) in addition to NDT Testing as per under item of "Testing of works"

Drilling suitable holes in reinforced cement concrete with power driven drill machine to a minimum depth of 10D(D-Dia of Bar in mm) in RCC beams, lintels, columns and slabs to introduce new steel bars including fixing the steel bars in position using Lokfix E75 a two-component epoxy anchoring material, supplied in 3:1 ratio having compressive Strength (EN196) >110 MPa, Flexural Strength (EN196) >40MPa, E Modulus (EN196) 10,800 MPa. or of equivalent make but excluding the cost of reinforcement, all complete as per direction of Engineer-In- Charge.

a) 8mm Shear Connectors

b) Anchoring bars for 10mm Dia

b) Anchoring bars for 12mm Dia

c) Anchoring bars for 16mm Dia

Providing and applying a non shrink, polymer modified cementitious micro-concrete Rendroc RG or equivalent from SIKA/BASF having compressive strength (BS 4551-80)-50 Mpa at 28 Days, Tensile strength- 2 Mpa @ 28 Days, Flexural Strength(BS 4551-80)-5 Mpa at 28 Days. product shall have A1 Class Fire Rating confirming to EN1504 cl 5.5, Thermal conductivity of 1.5W/m degree C. Renderoc RG can be applied in sections upto 100mm deep. Pouring the same into the formwork using suitable arrangement or if required using pumping device for uniform flow of micro concrete. Rate is inclusive of preparatory works from item i) to item v) below, rates also includes cost of materials labour, tools and plants, cost of shuttering & scaffolding, safety arrangement quality control and testing etc. complete as per specification and as directed by Engineer.-in-charge.

i) Chipping of plaster and unsound/weak concrete material till reinforcement bars to exposed to enable their rust removal vides item ii) below average thickness from slabs, beams, columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-incharge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads .

ii) Rust removal by Providing and applying Fosroc Reebaklens RR or equivalnet from SIKA/ BASF, a combination of acid based material, corrosion inhibitors and dispersing agents rust remover, for removal of all rust/ scales/corrosion from reinforcement bars before microconcreting or patch repair,It Shall be applied with brush for complete wetting of rusted metal surface at coverage of 2- 2.5 Sqm/ltr. & allow it to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal /steel for about 5-7 days. Before applying any protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth.

iii) Anticorrosive treatment by Providing and applying Nitozinc Primer an epoxy based zinc rich anti corrosive primer having adhesive bond strength ≥ 1.5 MPa as per ASTM D4541, & shall comply to per ASTM B-117 to be applied on well cleaned, fully exposed and all loose scale , rust free rust free surface obtained by grit blasting or suitable means , to be done with coverage @4.5sqm/litres to achieve a minimum thickness of 40microns DFT or as per direction of Engineer-In charge.

(iv) (a) Applying epoxy bond coat on the sound concrete substrate using approved spray machine or suitable brushes & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes). (b) Immediately after application of above bond coat as above pour prepacked dual shrinkage compensated micro concreting M40 grade, using approved mixing machines/pumping under pressure via approved pneumatic pump at the locations to be reparied in RCC beam & columns etc, upto 100 mm thickness of micro concrete.

v) Work will complete only after proper wet curing has been done and testing of Microconcrete cubes filled up and cured by contractor during column jacketing work (100 mm size cube crushing strength at the end of 28-day to be not less than 45 N/sq.mm) and NDT tests mandated under item "Testing of works"

SHOTCRETING /Gunniting (For through repairs of RCC elements like Slabs, Beams etc) with

a) 25 to 40 mm thick in grade M25 with cement content not les than 330 kg per cum up to 5th floor level

Shotcreting (Guniting) of R.C.C. components with approved mix mortar [with ordinary portland cement, coarse sand in proportion (1:3)] including the cost of materials, labour, Plants and equipment, centering and shuttering at edges and corner if required, propping, scaffolding and safety arrangment quality control & testing of works, the rate will also include Chipping (sub item i below) cleaning of concrete surface and reinforcement rust with sand blasting (sub item ii) below, wet curing quality control and testing etc. complete as per specifications and as directed by Engineer- in-Charge. Surface shall be evaluated by sounding /tapping with a blunt metal instrument by engineer incharge or his representative apart from cube tests for compressive strength of 25 N/sqmmand NDT tests under Item "Testing of Works"

i) Chipping of plaster and unsound/weak concrete material till reinforcement bars are exposed from slabs, beams, columns etc. with standard power driven percussion type or pneumatic chisel of standard make as directed by Engineer-incharge including tapering all edges, making square shoulders of cavities etc complete and disposal of debris up for all lifts and leads .

ii) Cleaning of concrete surface and reinforcement rust of by sand blasting with coarse sand followed by and including cleaning with oil free air blast so as to de-rust reinforcement bars as per direction of Engineer in charge.

Providing and laying in position M25 grade of cement concrete in beams,slabs, olumns upto a floor 5 level. Item rate is inclusive of all materials, labour, tools and plants, cost of shuttering & scaffolding, safety arrangement, quality control etc. complete as per specifications and as directed by Engg.-in-charge.

Reinforcement for R.C.C. work including straightening, cutting, bending and placing in position &/or welding with the existing bars wherever necessary complete as per drawings and specifications upto a floor 5 level and as directed by Engineer in charge

Water proofing treatment to roof surface with APP polymeric based water proofing membrane 3 mm thick & weighting not less than 3.5 KG/Sqm of approved make black finish consists of a comprising of center core reinforced with non woven polyester matt of minumum 160gm/Sqm with thermo fusible finsih and butane torch over a coat on an bitumen primer confirming to IS-3384 @ 0.4 Ltr/Sqm over and including 10mm thick rendering in CM 1:4 mixed with water proofing compund when concrete is green (WPC shall be measured separately), overlap with a propane or a butane gas torch with a overlap of 75mm at sides & 100 mm at ends & sealing including applying a coat of cold emulsion bituminous primer complete as per manufacturer's instruction complete all as specified and directed by Enineer-in-charge. (Make Super Thermo Lay manufactured by STP Ltd or Hyper Plas'(Polyester Manufactured by M/s IWL Ltd or 'Shalipals' (Polyster) manufacture by M/s Capital Steels and Chemicals Pvt Ltd). Note :- 1. Water proofing treatment shall be got carried out by the manufacturer or their authorised applicator only. 2. Bitumen Primer, Bitumen and Membrane shall be of same make/manufacturer. 3. The APP membrance to be inserted in the parapet wall/wall by cutting chases of atleast 65mmx50mm size & making good in CM 1:3.

(i) Surface Preparation: RCC Surfaces must be clean, even and sound concrete. Remove all oil, existing broken/damaged coving, dirt, laitance, protrusions(by light grinding) and other contaminants manually to attain a fairly smooth surface. Any undulations, pot holes, cracks shall be opened & treated with polymer modified mortar made by mixing Nitobond SBR @10% by weight of cement in Cement: Sand mix of ratio 1:3. This includes making of coving at all wall floor corners using PMM, complete in all respect as per the direction of Engineer incharge. The entire repair shall be allowed to cure before proceeding with any waterproofing treatment. Cement and sand shall be arranged by contractor himself.

(ii) Geotextile layer : Providing and installing 180 GSM non-woven geotextile membrane over the finish waterproofing treatment prior to protection screed as per specifications and direction of Engineer in charge

Pipe Penetration Treatment upto a floor 5 level: Providing and applying Nitobond EP an epoxy bonding agent over the PVC and internal side of of concrete after rubbing it with emery paper/sandppaper and fixing hydroswellable waterbar supercast SW in the centre of depth of slab. Later Filling the pipe gap with Conbextra GP2 leaving 20 mm * 20mm gap from the top all over the periphery, with all shuttering already in place. Later the gap shall be filled with Nitomortar S, two component epoxy mortar only after complete hydration of the prefilled grout, before treating the surface with Waterproofing layer. (Upto 100mm Dia)

M&L laying PCC of M-15 grade to specified slope upto a floor 5 level (min thickness at drain pipe 50 mm thick) mixed with approved water proofing compound like Conplast WL Xtra (Integral waterproofing compound confirming to IS 2645). This includes making of coving at the wall-floor corners using same concrete.

PLASTERING on ceiling and outer walls and other structuralal elements upto a floor 5 level over PMM/shotcrete repairs or otherwise as replaster as per details given under sub items (a), (b) and © below;

a) 6 to 10 mm thick cement plaster of in the ratio of 1 cement and 4 clean sand zone III added with Polymer SBR @2% of cement weight, on ceiling over PMM repairs, shotcrete repairs or as replaster of damaged plaster including preparation of surface by demarketing of PMM repaired surface in regular shape or removal of damaged plaster, direction of engineer in charge.

b) 15mm thick cement plaster in the ratio of 1 cement to 5 sand added with Polymer SBR @2% of cement weight over outer walls, columns or beams either over repaired surfaces like PMM , Microconcrete etc. including preparatory works like roughening of surface where required as per direction of engineer-in-charge

(c) Rate quoted against this item vides sub items (a) and (b) above shall include all materials, labour, Tools and Plants, Scaffolding, safety arrangement and preparation of surface as mentioned vides (a) and (b) above complete in all respects as per specifications and direction of Engineer in charge

Supply and providing of FRP Chhajjas of 450 mm width suitable for various opening, including grouting in existing wall and fitting with suitable screws and fixtures upto 5th floor level including all labour, material, tools and plants, scaffolding safety arrangement, quality checks complete in all respects as per specifications and direction of engineer-in-charge

Waterpoofing of Wet area upto a floor 5 level : Wet areas/ Sunken area/Utility area/Balcony area waterproofing using Fosroc Brushbond RFX or equivalent from SIKA/BASF

Waterproof Coating: Providing and applying two coats of Brushbond RFX, high performance, elastomeric, acrylic polymer modified cementitious coating having a mixed density of 1.6 kg/cc manufactured by fosroc chemicals india pvt. ltd and applied by fosroc's authorized applicators. Minimum recommended coverage is 0.5m2/per kg /2 coats to achieve a min DFT of 1mm. waterproof coating shall confirm to ASTM C-836, ASTM D 4541 & ASTM D 4060. Brushbond RFX coating shall exhibit below properties: 1. Abrason resistance ASTM-D4060 : 0.85 , 2. Tensile strength as per ASTM D412 is 1N/mm2 3. Adhesion to concrete is greater than 1N/mm2 4.static crack accommodation ASTM-C836. min 1mm System include supply and application, all complete as per the fosroc methodology. Item shall include making of coving at all the wall-floor corners using 1:4 Cement Sand mortar admixed with Nitobond SBR latex, & termination at 300mm above FFL by cutting of 10mm X 10mm chase and later filling with Nitobond SBR Latex admixed PMM. Size of coving may vary as per site conditions. Payment shall be made as per actual area of measurement. Rates are inclusive of cost of preparatory works vides item (i) and item (ii) below. Rates includes all materials, labour, tools, plents, safety arrangement, quality control and testing etc. complete as per specifications and direction of Engineer in charge.

(i) Coving: Opening up the corners of Wall-floor corners to a minimum 10mm *10mm groove, later cleaning the same using water, later filling the groove using 1:3 Cement Sand Mortar Admixed with Nitobond SBR Latex @ dosage of 10% by wt. of cement, followed by making of concave coving of size 40mm *40mm, including finishing, curing, all complete as per manufacturer's methodology. (ii) Construction Joint & Crack Treatment: Chase open construction joints in v shape of 15mm x 15mm using suitable means, later cleaning the same using water jet and applying a bond coat of Nitobond SBR Latex mixed with cement and water in a ratio of 1:1:3(Water : Polymer : Cement), followed by filling of Nitobond SBR Latex admixed PMM in the groove, including, filling, finishing, curing all complete as per the direction of Engineer In-Charge. In case of structural cracks, injection grouting shall be carried out either using Cementitious Grout or Low viscous epoxy grout, depending upon the kind of cracks. In case of poor/weak construction joints, injection grouting at the CJ's should be carried out depending upon the joint characterstics and shall be paid separately.

Bore Packing upto a floor 5 level : Providing and applying Nitobond EP an epoxy bonding agent over the PVC and internal side of of concrete after rubbing it with emery paper/sandppaper and fixing hydroswellable waterbar supercast SW20 in the centre of depth of slab. Later Filling the pipe gap with Conbextra GP2 from the top all over the periphery, with all shuttering already in place, (Upto 100mm Dia).

Protection Plaster over water proofing layer: Providing and applying Cement plaster/screed of proportion 1:4 / 1:2:4 admixed with integral waterproofing admixture Conplast WL Xtra, a advanced technology based, Corrosion resistant admixture as per ASTM G1, JISZ 1535 mixing @ 200ml/bag of cement. This shall include all champering , rounding off of corners, protusion and shall include shuttering cost or as per Engineer in-charge specification. Cement and sand will be in client scope.

a) 12mm thk 1:4 Cement: Sand Plaster for Verticals Areas

b) Min. 40mm thk (1:2:4 )Screed for Horizontal Areas

Testing of Works: Apart from supervision and inspectionof materials the Works under this work order (Shekhawati Blocks) would be tested by NDT methods; for this purpose 10 Rebound Hammer Tests and 10 UPV tests Tests would be conducted on PMM, Microconcrete and Shotcrete (Gunniting) works per block (on an average basis) would be conducted as per specifications of materials and applications as also the specifications of NDT tests and as directed by Engineer in charge. The cost of these tests shall be born by contactor and this cost is supposed to be built up in items of work above, no separate payment will be made on this account.

Description of Work / Item(s)

Amount

Taking down carefully copper/aluminium point wiring (light/fan socket or power) complete including fittings such as switches, ceiling roses, pendents, regulators, sockets, light fittings etc and removing the material from site including making good the disturbed surface to match with the existing all as specified and directed by Engineer-in-charge.

Material and labour for concealed point wiring with PVC insulated unsheathed multistranded colour code copper conductor in PVC conduit with FRLS cable1.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box of 1.6 mm thick including one coat of synthetic enmelled black paint and providing modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5 Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit all as specified and directed by Engr-in-charge for the following :-

(a) One light/fan/Exhaust fan/bell point controlled by one switch.

(b) All as per item No. 2(a) here in before but for One 5 Amp socket out let independent.

(c) All as per item No. 2 (a) here in before but for One 5 Amp socket out let on same board

(d) All as per item No. 2 (a) here in before but one light point controlled by two 2 way switches.

Material and Labour for concealed point wiring with PVC insulated unsheathed multistranded FRLS copper conductor in PVC conduit with cable 2.5 Sqmm size 1100 volts grade conforming to IS:694 in new modular metal flush box of 1.6 mm thick including one coat of syenthetic enamelled black paint with new modular white cover plate with frame of suitable size of required colour fixed with brass screws and cup washers including single core stranded FRLS copper conductor 1.5Sqmm PVC insulated cable as earth wire to common earth and connected to earth dolly and earth terminal box drawn in same concealed conduit for One 3 Pin socket 15A Indepentent board

S&F of switch Piano flush type 5/6 amps single pole one way complete all as specified and directed

S&F of switch Piano flush type 15/16 amps single pole one way complete all as specified and directed

S&F of socket outlet multipurpose 2/3 pin 5/6 amps flush button type complete all as specified and directed

S&F of socket outlet multipurpose 2 in 1, 6/16 Amp flush button type complete all as specified and directed..

S&F polycarbonate ceiling rose 3 pin flush type 6 A 250 V AC with ISI mark including ring for jumbo ceiling rose.

S&F of electronic fan regulator 0-4 steps step 100 W hum free complete all as specified and directed..

S & F LED light fitting 1X10W bulk head luminaires includin LEDlight driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F for Decorative walll light fixture made up of Polycarbonate, Spiral B-22 Base suitable for 7 Watt LED Lamp including 7Watt Lamp complete all as specified and directed..

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.complete all as specified and directed.

S&F single pole MCB 6 to 32Amps 240 v, 50 Hz AC suitable for 'B' Series" conforming to IS 8828 of 1996 including taking down old MCB's all as specified.

S&F single pole MCB 40 Amps 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘B’ curve, 10 KA breaking capacity and terminal box suitable upto 35 sqmm cable complete conforming to IS 8828 of 1996 all as specified. .

S&F SPN MCB 32 amp, 240 v, 50 Hz AC Made from moulded self-extinguishing thermostat plastic and suitable for ‘C’ curve, 10 KA breaking capacity and terminal box suitable upto 63 sqmm cable complete conforming to IS 8828 of 1996 all as specified.

S&F in repair of factory made epoxy polyester powder coated distribution board TP & N 6 way (VTPN MCCB DB) with metal double door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch

S&F in repair of factory made epoxy polyester powder coated distribution board TP & N 4 way (VTPN MCCB DB) with metal double door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed on wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, earth bar and cable ties for cable management, top and bottom removable gland plates with provn for DPX 160, 4 pole MCCB and ELM as incommer and 12 SP MCBs outgoings complete all as specified and conforming to IS: 8623 along with cable end box for above DB including taking down old DBs all as specified. NOTE :- (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

S&F MCCB 125 Amp 4 pole 16 KA at 415 V with fixed thermal megnatic release complete all as specified directed.

S&F in repair of factory made epoxy polyester powder coated distribution board SP & N 8 way fabricated from minimum 1.6 mm thick CRCA sheet with metal double door (IP-43 protection ) fixed flush to wall and suitable for universal mounting and including 200 Amps copper bus bar, Neutral bar, standard DIN rail, eath bar and cable ties for cable management, top and bottom removable gland plates with knockouts and suitable for one DP MCB as incomer and 6 SP MCBs as outgoings complete all as specified and conforming to IS: 8623 alongwith cable end box for above DB all as specified and directed. NOTE (a) MCBs shall be measured and paid separately. (b) All cables terminating into MCBs shall be connected by using suitable copper lugs/thimbles/sleeves and its cost shall be deemed to be included under respective item of Sch.

Taking down sub main wiring off sizes.

S&F submain concealed wiring alongwith earth wire with 2 runs of 6 Sqmm (Main Cable and neutral) and one run of 6 Sqmm as earth wire of multistranded unsheathed colour code FRLS PVC insulated copper conductor, single core cable drawn through and including rigid PVC conduit of size 25 mm dia with all fittings and accessories all as directed.

M&L for earthing complete with galvanised steel earth plate 600 x 600 x 6.3 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) in repair with top edge of the plate not less than 1.5 meter normal ground level, connected to galvanised iron strip 25x4mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel besides welding at all joints all as shown in electrical plate no 3 of SSR Part I including excavation and earth work, GI pipe light grad 25 mm bore for protection of earth strip from earth electrode & GI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate no 3 of SSR Part I and connected to earth test point including testing on completion complete all as specified and directed.

S&F Exhaust fan metallic type ventilating single phase 230/240V of 300mm sweep with Louvre including cutting of holes in a round shape and including fixing the ventilating fan complete all as specified and directed.

Taking down existing ceiling fan of any make and sweep and deposited to MES store yard.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistantcomplete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. complete all as specified and directed.

S & F in replacement Lamp holder with insulated body with back plate suitable for batten fitting complete all as specified and directed..

S&F in replacement of 7 Watt LED lamp 6500K, complete all as specified and directed..

S&F of electric storage water heater of capacity 25 ltr BEE 5 star with vtreous enamel coating with all accessories and fittings arrangements and testing after installation complete all as specified and directed.

S&F bib taps 15mm fency type with crutch or butterfly handle, screwed down screwed for GI pipe .

S&F stop valve 15mm fency type chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for GI pipe.

S&F GI tubing pipes galvanized, "Medium class", supplied and laid complete including fittings 15 mm (1/2") dia.

Cutting of Existing water supply main any size upto 25 mm for Taking branch connection for taking branch connection of size 15 mm including insertion of Tee unegual all as required at site or directed by Engr-in-Charge.

Supply and fixing 250 mm PVC Fresh Air exhaust fan single phase, 230/240 V With Louvre including cutting of holes in a round shape (Precast piece to be incorporated for smooth and ever finish) and including fixing the exhaust fan complete all as specified.

S&F switch piano flush type SP two way 6 Amp complete as specified and directed

S&F bell push flush type 5 Amp complete all as specified and directed.

S&F bell AC 230 volts single pole complete all as specified and directed.

AMIT ASSOCIATES

M/s Matadeen Ramchandra Agarwal

Global Enterprises

LUMOS INFRA PVT LTD

AMIT ASSOCIATES

M/s Matadeen Ramchandra Agarwal

Global Enterprises

LUMOS INFRA PVT LTD