Refurbishment and upgrading of flooring, wall cladding and certain other misc. B/R works in Fort Cantt under GE (East) Prayagraj.

Amount

Demolition of floor concrete in ground floors and pavings n exc15 cm thickness (below or above ground level) complete all as specified and directed.

M&L PCC 1:4:8 Type D-2 using 40mm graded crushed stone aggregate, as in foundation filling and mass concrete complete all as specified and directed.

M&L coloured rubberised Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and no pigment complete all as specified and directed.

Supply only Fine aggregate (sand) for laying floor finishes complete all as specified and directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Machine pressed precast concrete interlocking paver block except tiles with grey cement and no pigment and approved colour, design & pattern as in footpath, parks, lawns, drive ways any shape and size laid in required colour & pattern as fixed in repair including 75 mm PCC (1:4:8) and 25 mm thick sand cushioning complete all as specified and directed.

M & L for plain cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) in levelling course for floor heavy duty tiles in open area benching etc, finished even and smooth witht out using extra cement, complete all as specified and directed.

M&L for heavy duty out door coloured ceramic tiles exceeding 0.11 sqm but not exceeding 0.18 sqm 12 mm thick set and jointed in neat cement slurry & pointed with coloured cement to match in floor over and including 15 mm thick screed bed in cement mortar (1:4) including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

M & L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in copings, kerbs including necessary formwork etc complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) in plinth protection, finished even and smooth witht using extra cement, complete all as specified and directed.

Material and Labour for Non - skid coloured eramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes over25 mm thick PCC 1:2:4 type B0 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

Material & Labour vitrified tiles 10 mm thick ,area of each tile exc 0.36 Sqm but n.exc 0.42sqm, in floor etc set and jointed in neat cement slurry including 15 mm screed bed CM 1:4 over25 mm thick PCC 1:2:4 type B0 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

Material & Labour Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including incl 10mm thick plaster in cm 1:4 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

S & F prepainted coloured galvaniume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile stregnth of 550 mpa as in roof covering and gladding to wall fixed with self tapping screws complete all as specified and directed.

S & F prepainted coloured galvaniume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to roof wall, fixed with self tapping screws complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

M & L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.

M & L for synthetic enamel painting two coats to New Steel surfaces over a coat of red oxide primer including preparation of surfaces of any description over 10cm girth or width not other wise described.

M&L for preparation of old painted steel surfaces of any description, not otherwise described over 10 cm in width or girth and applying one coat synthetic enamel paint complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation board/slabs/blankets/AC boards etc any thickness complete all as specified and directed.

Supply & Fix anodised aluminium snap grid frame work for false ceiling all as specified. (Size of grid 605 X 605 mm) hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified complete all as specified and directed.

Supply & Fix 4 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified and directed.

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frame).(Ventilator and Window)

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (Without taking off shutters from the frame).(Doors and Window)

Supply & Fix Powder coated Anodised aluminium frame(Thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Supply & Fix Powder coated Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in- Charge.

Providing and fixing factory made UPVC white colour Sliding window Three track area not Exceeding 2.0 sqm each complete all as specified and directed.made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

Providing and fixing factory made UPVC white colour Sliding window Three track area Exceeding 2.0 sqm each complete all as specified and directed.made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware.EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.)

Supply & Fix 5.5 mm thick plain sheet glass as in,shutters with and including rubber gasket and natural colour anodized 15 micron snap on aluminium beading/glazing, clips etc complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.00mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S &F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to grade Fe 290 Gde-E-165 complete all as specified and directed.

S&F in repair 100 mm size 4-lever mild steel mortice lock vertical type with two keys etc complete all as specified and directed.

S&F in repair Aluminium die cast body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed.

S & F Pressed steel frames factory made for doors out of 1.25 mm thick PBI sheet with one of more rebates including necessary flat iron lugs,hinges, lock strike plate, hinges etc complete, size of frame 125 x 60mm including tarring ends and back of chowkats and lugs including back filling of PCC 1:3:6 for chowkats & PCC 1:2:4 for block for hold fast including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

S & F Pressed steel frames factory made for doors out of 1.25 mm thick PBI sheet with one of more rebates including necessary flat iron lugs,hinges, lock strike plate, hinges etc complete, size of frame 105 x 60mm including tarring ends and back of chowkats and lugs including back filling of PCC 1:3:6 for chowkats & PCC 1:2:4 for block for hold fast including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

S & F 35 mm thick, 2nd class hard wood glazed and skelton shutter, open rebated and prepare to receive glass, gauzed etc(without sash bars) edges of framming plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR PART I Section 8 clause 8.24(a) supplied and fitted to chowkhat complete all as specified and directed.

S & F in 35 mm thick flush door shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F Factory Made Solid PVC Moulded Door Shutter (with wood free EPS), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

Material & Labour preparation of new wooden surfaces over10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

S & F Aluminium anodised handle extruded section of size 150mm complete all as specified and directed.

S & F 125 mm butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

S & F Aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed.

S & F Aluminium anodised barrel tower bolts extruded section of size 200 mm, complete all as specified and directed.

S&F in repair Door Seal length of each door seal is equal to width of door fixed to door bottom rail including all fixing arrangement such as screws ,nails etc complete all as specified and directed.

S & F 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

S & F in repair Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor Door Stopper 140 mm complete all as specified and directed

S & F in repair 25 mm dia stainless steel drapery rod cut to size and fixed in position including brackets, cap both ends fixed to wall complete all as specified and directed.

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc.

M & L for Brick work with fly ash (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6.complete all as specified and directd.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.

M & L for rendering 10 mm thick on other than fair faces of walls of brick work or concrete surfaces in cement mortar 1:6 compound finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Rendering 15 mm thick on fair faces of walls of brick work or concrete surfaces in cement mortar 1:4 with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. Note: water proofing compound shall be measured & paid seprately.

Supply only liquid water proofing compound complete all as specified and directed.

M & L for preparation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over one coat of birla white putty 1 mm thick preparatory to distempering complete all as specified and directed.

M & L for preparation of newly external plastered surfaces of wall and applying two coats of weather proof paint of APEX of Asian paints or its equivalent over a coat of white primer including applying 2mm to 3mm thick wall care putty all as specified and directed.

M & L for complete removal of existing treatment on walls with electric operated blade, washing, rubbing down and stopping of plastered surfaces of wall and applying two coats of weather proof paint of APEX of Asian paints or its equivalent over a coat of white primer including applying 2mm to 3mm thick wall care putty all as specified and directed.

M&L for preparation of old plastered surface and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care putty including complete removal of existing treatment complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and directed.

S & F GI tube 15mm bore medium grade with all fittings fixed to walls and ceilings or laid in floor complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe.

M & L 20mm bore GI tubing medium grade with all fittings and fixed complete to walls/ ceiling or laid in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fix 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old tank complete all as specified and directed.

S & F in repair 20 mm dia Gun metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in repair 15 mm dia Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in repair 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 g ms) complete all as specified and directed.

S&F in repair vitreous china wash hand basin with pedestal pattern white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supply & Fixed in repairs vitreous china pedestal pattern (P Trap) type white wash down water closet pan with Antimicrobial Solid Seat Cover Code No.: C8094 but excluding flushing cistern and flush pipe complete all as specified and directed.

S&F in repairs 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, aluminium brackets for bottom support fixing with gitties embeded in wall with drilling machine etc complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Supply and Fix in repairs Health faucet (Hand shower) with 1metre flexible tube with wall hook, Chromium Plated as per cat no HF3342 of Jaguar or equivalent of HR. Johnson/Parry ware all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete all as specified and directed.

S&F in repair 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete all as specified and directed.

S&F in repair pillar tap cast copper alloy with capstin heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125 mm size and fixed complete all as specified and directed.

S&F in repair 15 mm bore stop valve fancy type chromium plated with long cup and shank (Concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S & F in repair Cabinet Mirror PTMT 450 x 555 mm with sided shelves fancy type of superior quality complete all as specified and directed.

S & F in repair corner glass shelf superior quality matt finished crromium plated (MCH/Colour CP ) with bracket and fittings complete all as specified and directed.

Supply and fix in repair soap dish ,matt finished chromium lated (MCH/Colour) as per Jaquar Continental Wall Mounted ACN-CHR-1131N Soap Dish Holder complete all as specified and directed.

Supply and fix in repair glass shelf matt finished chromium plated (MCH/Colour CP) Jaquar Continental ACN-CHR-1171N 600 mm Glass Shelf - (Chrome, Wall Mounted) bracket and fittings complete all as specified and directed.

Supply and fix in repair toilet paper holder with flap recessed type chromium plated complete all as specified and directed.

S & F in repair brass in repair chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges including brackets fixed to wall complete all as specified and directed.

S & F in repair 250 mm size mild steel peg stay fixed to steel window (as per sample) complete all as specified and directed.

S & F in repair 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified and directed.

S & F in repair 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repair PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified.

S & F in repair PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) bends any radius with oval access door complete all as specified and directed.

S & F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S & F in repair 110 mm dia PVC (SWR) plain bends any radius complete all as specified and directed.

S & F in repair 75 mm dia PVC floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for Pre-cast RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cover slab of manholes, septic tanks, etc. and set in cement mortar 1:4 including dismantling of damaged RCC covers slab complete all as specified and as directed. NOTE : Reinforcement will be measured and paid for separately under relevant Item(s).

M&L for mild steel TMT bars 10 mm dia and over cut to length bent to shape required including cranking bending, spirally for hooking for hooking and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

M/S A P CONSTRUCTION (BID ID -3088784)

M/s Rahul Kumar Agrawal (BID ID -3089522)