GIRLS HOSTEL BUILDING

Amount

125mm. Thick brick work with 1st class bricks in cement mortar ( 1:4 ) in 3rd Floor i) Third floor

Plaster ( to wall, floor, ceiling etc. ) with sand and cement mortar including rounding off or chamfer-ing corners as directed and raking out joints including throating,nosing and drip course,scaffolding/staging where necessary.[ Excluding cost of chipping over concrete surface ] ( 2nd Floor ) ( i)With 1:6 cement mortar (b) 20mm thick plaster

A) Second floor

B) Third floor

(ii)With 1:4 cement mortar (b) 10mm thick plaster A) Second floor

B) Third floor

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete , Iron Butt Hinges and M.S clamps. ( The quantum should be corrected upto three decimals). Sal:Siliguri ( 2nd Floor )

i) Second floor

ii) Third floor

Panel shutters of door and window, as per design (each panel consisting of single plank without joint),including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor.( In case of non supply of single plank, penal rate of reduction of 20% will be made) 40mm thick shutters with 19mm thick panel of size 30 to 45 cm Sishu, Gamar,Champ, Badam,Bhola,Mogra,Hallak.

i) Second floor

ii) Third floor

Supplying fitting and fixing Marble Slab/tile of 15 to 18mm thickness in floor,lobby,stair,landing & treads etc. Over 20 mm ( av.) thick base of Cement mortar ( 1:2) laid with white cement slurry @ 4.4 kg/Sq.m before placing marble & jointed with white cement slurry @ 2.0kg/Sq.m with necessary pigments including grinding and Granite polishing as per direction of Engineer -in -Charge in Ground Floor. [White cement and pigment to be supplied by the Agency] (b) With Chawk Dungri (ii)Area of each tile exceeding 0.3Sq.m. but not exceeding 0.6Sq.m.

i) Second floor

ii) Third floor

Supplying,fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones ( 10mm ) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface,if necessary or by synthetic adhesive & grout materials etc. ( D ) Wall With Polymerised Adhesive & Epoxy grout pointing including spacer - 2 mm ( When Tiles are laid over existing hard ready surface ) Area of each tile each tile above 0.09 Sq.m [using adhesive 4.5mm thick]. (i) Coloured decorative (b) Area of each tile above 0.09 Sq.m [ using adhesive 4.5mm thick]

i) Second floor

ii) Third floor

Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand. 1.5 mm. thick

i) Second floor

ii) Third floor

Acrylic Distemper to interior wall,celling with a coat of solvent based interior grade acrylic primer ( as per manufacturer's specification) including cleaning and smoothening of surface. Two Coats

i) Second floor

ii) Third floor

( a) On timber or plastered surface : With super gloss (hi - gloss ) Two coats ( with any shade except white)

i) Second floor

ii) Third floor

Supplying , Fitting & Fixing 30mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19mm x 19mm for styles, top and bottom rails, M.S.frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5mm th. Heat moulded PVC "C" channel of size 30mm th, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either sides forming styles; and 5mm th. 95mm wide PVC sheet out of which 75mm shall be flat and 20mm taoered in 45 degree on the inner side to form top & bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat & 20mm shall be tapered on both sides to form lock rail. Top , bottom and lock rails shall be provided either side of the pannel with 10mm ( 5mm x 2 ) th., 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5mm th. Both side PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with 7mm ( 5mm + 2mm) th. X 15mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5mm th.PVC strip of 20mm which is to be stuck on the interior side of the " C " channel using PVC solvent adhesive etc. complete excluding all necessary hardware as per direction of Engineer-in-Charge in ground floor.

i) Second floor

ii) Third floor

Supplying ,fitting and fixing CPVC ( Chlorinated Polyvinyl Chloride ) pipes of approved make conforming to IS-15778 :2007. With all necessary accessories, specials viz. socket,bend,tee,union,cross,elbo,nipple,longscrew,reducing socket,reducing tee, short piece etc. fitted with holder bats clamps,including cutting pipes,fitting,fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials in any position above ground. ( Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories,specials. For Concealed Work CPVC Pipes Class-1,SDR -11 25 mm

i) Second floor

ii) Third floor

Supplying,fitting and fixing PVC pipes of approved make of Schedule 80( medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS:1239 (Part -I) , with all necessary accessories,specials viz.Socket bend,tee,union,cross,elbo,nipple,longscrew,reducing socket,reducing tee,short piece etc.fitted with holder bats clamps,including cutting pipes,making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paints in any position above ground.(Payment will be made on the centre line measurements of total pipe line including all specials.No separate payment will be made for accessories,specials. Payment for painting will be made seperately) 80mm

i) Second floor

ii) Third floor

Supplying P.V.C. Water storage tank of approved quality with closed top with lid(Black)-Multilayer 1000 litre capacity

Supplying P.V.C. Water storage tank of approved quality with closed top with lid(Black)-Multilayer 1000 litre capacity 75mm x 75mm wooden blocks,C.P. waste fittings of 32mm dia., one approved quality brass C.P.piller cock of 15mm dia.,C.P. chain with rubber plug of 30mm dia.,approved quality PVC waste pipe with C.P. nut 32mm dia.,900mm long approved quality PVC connection pipe with heavy brass C.P.nut including mending good all damages and painting the brackets with two coats of approved paint. 550mm x 400mm size

i) Second floor

ii) Third floor

Supplying,fitting & fixing Cast Iron soil pipe only confirming to IS,3989/2009 and I.S.1729/2002 with bobbins, nails etc. including makimg holes in the wall,floor etc. and cutting trenches etc. in any floor through masonry concrete , if necessary, and mending good damages with necessary jointing materials and painting two coats to the exposed surface with approved paint complete.( Measurment will be made along the centre line of the total pipe line in fitted condition including specials,payment for specials & Painting will however be paid seperately). With valamoid joints including sealing with sand cement morter ( 4:1) upto quarter depth. 100mm dia.(internal)

i) Second floor

ii) Third floor

Supplying , fitting and fixing shallow water closet Indian pattern( I.P.W.C.) of approved make in white vitreous chinaware in position ( excluding cost of concrete for fixing).510mm long

i) Second floor

ii) Third floor

Supplying fitting and fixing E.W.C. in white glazed vitreous chinware of approved make complete in position with necessary bolts,nuts etc. with ' S' trap

i) Second floor

ii) Third floor

Supplying , fitting and fixing bevelled edged mirror 5.5mm thick silver red as per I.S.3438/ 1965 together with brass C.P. hinges. ( ii) 600mm x 450mm

i) Second floor

ii) Third floor

Supplying fitting and fixing towel rail with two brackets. 25 mm dia, and 600 mm long

i) Second floor

ii) Third floor

Supplying , fitting and fixing Sheet steel Main Switches on flat iron frame on wall 30/32A Havells 240V DP with fuse on L&N

i) Second floor

ii) Third floor

Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection.Seimens 40 A, DP, ( Crabtree )

i) Second floor

ii) Third floor

Supplying & fixing angular batten holder ( Anchor ) on 75 mm dia PVC round block/ round bakelite on wall/celling

i) Second floor

ii) Third floor

Supplying & fixing bulk head light fitting ( Havells make) with die cast aluminium housing & frosted glass on wall/ceilling incl.S & F 8watt CFL/ 100 watts GLS Lamp complete Set.

i) Second floor

ii) Third floor

Supplying & fixing pendent light fitting complete with holder incl.S&F 24/0.20 twin twisted tinned copper conductor flexible cord and suspended below ceilling /beam upto 45cm

i) Second floor

ii) Third floor

Supplying & fixing MS fan clamp of two piece type for RC ceilling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting - ( As per Drawing no. 475 of PWD Specification Book - May 1991 )

i) Second floor

ii) Third floor

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire ( Brand approved by EIC ) of the following sizes in the prelaid polythene pipe and by the prelaid GL fish wire and making necy. Connection as required. a) 3 x 36 / 0.3 ( 2.5 Sq.mm )

i) Second floor

ii) Third floor

b) 3 x 56 / 0.3 ( 4 Sq.mm ) i) Second floor

b) 3 x 56 / 0.3 ( 4 Sq.mm ) ii) Third floor

Distn. Wiring in 22/0.3 ( 1.5 Sqmm ) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire ( Brand approved by EIC ) in 19 mm bore,3 mm thick polythene pipe complete with all accessories embedded in wall to light/fan/call bell points with Piano key type switch ( Anchor make ) fixed on sheet metal ( 16 SWG) switch board with bakelite/ perspex (wall matching colour) top cover ( 3 mm thick ) flushed in wall incl. mending good damages to original finish. 2x22/0.3(Ph. & N) and 1 x 22/ 0.3 as ECC. Avarage run 8 mtr.

i) Second floor

ii) Third floor

Distn. Wiring in 22/0.3 ( 1.5 Sqmm ) single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire ( Brand approved by EIC) in 19 mm bore,3 mm thick polythene pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch ( Anchor make ) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with bakelite / perspex (wall matching colour) top cover ( 3 mm thick) flushed in wall incl.mending good damages to original finish. 2x22/0.3(Ph. & N) and 1 x 22/ 0.3 as ECC. On Board

i) Second floor

ii) Third floor

Supplying & Fixing GI Modular Switch Board of the following sizes complete with three no. suitable size Copper bar with holes ( for Ph, N & E ) fixed on bakelite / Hard rubber insulator over the MS welded chairs incl. top cover flushed in wall for housing the board after cutting the brick wall incl. making earthing attachment, painting and mending good damages to building works.

a) 6 Module i) Second floor

a) 6 Module ii) Third floor

b) 12 Module i) Second floor

b) 12 Module ii) Third floor

Supply & fixing 240 V 6 A Modular type Switch ( Brand approved by EIC ) on existing GI Modular type switch board having top cover plate and making necessary connections as required.

i) Second floor

ii) Third floor

Supply & fixing 240 V 16 A Modular type Switch ( Brand approved by EIC ) on existing GI Modular type switch board having top cover plate and making necessary connections as required.

i) Second floor

ii) Third floor

Supply & fixing 240 V, 6A, 5 pin Modular type Plug socket (Brand approved by EIC ) without switch & Plug top, on existing GI Modular type switch board with top cover plate and making necessary connections with PVC Cu wire and earth continuity wire etc.

i) Second floor

ii) Third floor

Supply & fixing 240 V 16A 3 pin Modular type Plug socket ( Brand approved by EIC ) without switch & Plug top, on existing GI Modular type switch board with top cover plate and making necessary connections with PVC Cu wire and earth continuity wire etc.

i) Second floor

ii) Third floor

Supply & fixing 240 V Modular Socket ( 2 Module ) type Fan regulator ( Step type) ( Brand approved by EIC ) on existing Modular GI switch board with top cover plate incl. making necessary connections etc.

i) Second floor

ii) Third floor

Supply ing of 250 Volts single phase AC 920 RMP,300 mm sweep exhaust fan ( EPC make )

i) Second floor

ii) Third floor

MACNEILL ENGINEERING LIMITED

LABANYA SARKAR