Loading
Loading…
Loading…
Tender Value
₹6.2 Cr
EMD Value
₹12.5 L
Closing Date
11 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
(PH-31)
WEST
14 conditions · 2 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Note :- (i) For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date). (ii) In case, date of tender inviting is on or after date of statutory deadline for audit of balance sheet of previous Financial Year (i.e. 30th Sept. or as further extended for this FY), audited balance sheet of 4th previous year shall not be considered unless concerned CA certifies that balance sheet is not audited yet as on date of invitation of this tender.
The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (a) Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or (b) Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or (c) One similar work costing not less than the amount equal to 60% of advertised value of the tender. Note :- For Joint Venture (JV): The tenderer shall submit credentials as mentioned in Clause 17 of GCC April 2022 (Ammended upto date).
Defination of Similar Work :- Any Track work (Note :- 1. Fabrication of Glued joints should be done by RDSO approved manufacturer as per the extant guidelines on the subject. 2. Ballast supply / formation work will not be considered under this item)
7 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Note:- (1) The quantities and cost mentioned above are rough and only for guidance and may vary according to needs of the railways and variation there of May extent will not be the basis of any claims against the Railway. (2) The work shall be carried out as per item descriptions/specifications of IR USSOR-2021 Items, CPWD DSR-2023 Items & Non-Schedule Items (Amended up to date). (3)The rates should be inclusive of all charges such as tools and plants and all cost of labour & material, taxes, GST etc. Extra payment what so ever on any account will not be payable to the contractor. (4) Contractor/ suppliers/ service providers/ parties shall register their firms under EPFO & GSTIN (GST Identification Number). (5)The contract shall be governed under General Condition of contract and instructions to tenderer-2022 (Amended up to date). (6) The Railway Administration will not be responsible for the safety of contractor's labour engaged for this work. (7) The contractor shall make his own arrangements for men, tools, labour etc .required for the work at his own cost.
Lalgarh -Kolayat-TRR (P) of 60kg for 45.877 TKm under jurisdiction of ADEN/Line/Bikaner.
144-26-27~NWR
144-26-27
Open
Works - General
12 Months
Bikaner, Rajasthan
₹0
₹12.5 L
20 Aug 2026
20 Aug 2026
28 Aug 2026
141 items across 11 schedules · ₹5,48,84,475.21 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| Pulling & positioning of rails accurately on cess including supporting rails, providing required gap and squaring at ends for renewal preparation, as directed by Engineer in-charge. | — | — | — | — | |
| 1 | Up to 40 m long rail panel | RM | 2952.00 | 9.8 | 28,929.6 |
| 2 | More than 40 m long rail panel | RM | 87501.00 | 15.5 | 13,56,265.5 |
| 3 | Extra to Item no. 061011 for working on bridge | RM | 373.00 | 4.29 | 1,600.17 |
| Dismantling and removing rail of all section & length from track, laid on any type & density of sleeper by removing fish plates, fastenings & fish bolts and other materials including stacking all released materials within an average distance of 500 metres as directed by Engineer in-charge. Note: 1.Cutting of rails shall be paid separately. 2.Work to be done under traffic block. | — | — | — | — | |
| 4 | For Through Rail Renewal work | TRM | 45877.00 | 48.05 | 22,04,389.85 |
| 5 | For Casual/Scattered Rail Renewal work | RM | 3184.00 | 38 | 1,20,992 |
| Insertion of rails of all types & length in track, laid on any type & density of sleeper to the specified gauge under traffic block. Rates include fastening of rail with sleepers with standard set of fastenings and fixing of fish plates and bolts or, if required, providing gap for welding and stacking of released material without infringement within 250m as directed by Engineer-in-Charge. Note: Rail drilling and cutting to be paid separately. | — | — | — | — | |
| 6 | For Through Rail Renewal work | TRM | 45877.00 | 49.55 | 22,73,205.35 |
| 7 | For Casual/Scattered Rail Renewal work | RM | 3184.00 | 40.24 | 1,28,124.16 |
| Re-spacing of existing PSC sleepers for Increasing Sleeper Density (ISD) work in track after marking of sleeper spacing as per required sleeper density, including fixing all fastenings and initial packing and all associated work required to complete the work, as directed. Note: Insertion of new sleeper will be paid extra under relevant item. | — | — | — | — | |
| 8 | For location of work not involving deep screening | TRM | 45877.00 | 177.73 | 81,53,719.21 |
| Replacement of any type of sleepers in track with PSC sleepers lying on cess or at Bridge Approaches for casual renewal at isolated locations with all fittings complete to specified gauge & cross level with contractor's tools including packing and dressing of ballast, as directed by Engineer in-charge. Released materials shall be neatly stacked and handed over at specified location within an average lead of 250 m or near either side of Bridge approaches as directed. | — | — | — | — | |
| 9 | Locations other than Ballasted Deck Bridge | Each | 504.00 | 507.15 | 2,55,603.6 |
| 10 | Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert by using wire brush, scrapper / sand emery paper etc supply and application of graphite grease, as prescribed by Railway for under side of liners & corresponding area of rail foot & SGCI insert with ERCs and re-fixing the same as per procedure prescribed in latest edition of IRPWM with contractors grease and all other tools & plants complete and as directed. Note: Each ERC in this item shall constitute 1 ERC and its Liner Contact area. | ERC | 378128.00 | 5.16 | 19,51,140.48 |
| 11 | Removing seized ERC from SGCI inserts of existing track by using suitable approved chemicals and re-fixing after greasing of insert eye and ERC with Contractor's grease of specified quality as per provisions of IRPWM, as directed by Engineer in-charge. Note: 1.List of Seized ERC along with location shall be prepared after inspection of SSE/P.Way and marked prior to execution of this item. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if SGCI insert is broken or sleeper gets cracked in the process. | ERC | 5294.00 | 53.1 | 2,81,111.4 |
| 12 | Lubrication of gauge face of rail on curves, cross overs, points & crossings, turn-in curves and at locations as required with contractor's grease graphite grade "O" IS 408 and as directed. | RM | 12604.00 | 4.65 | 58,608.6 |
| 13 | Renewal of seized Plate/Rail screws on PSC Sleepers by using gas or any approved methods, duly drilling holes in broken screw and removing existing screw pieces from the holes along with existing dowels and fixing new contractor's dowels (procured from RDSO approved sources) and grouting around dowel with Epoxy materials of approved specification and refixing new Railway's rail/Plate screws duly greasing the s c r e w w i t h specified grease with all contractor's materials, consumables, tools & plants, labour with all lead, lift. Note: 1.Seized screws shall be identified and marked by JE/P.Way and verified at minimum SSE/P.Way In charge) level. 2. Due care shall be taken to avoid any damage to the sleeper 3.A penalty of 50% of the basic cost of new sleeper in nearest sleeper factory shall be levied on each, if sleeper gets damaged in the process. | Each | 2521.00 | 294.73 | 7,43,014.33 |
| Gas cutting of rail of various sections with contractor's tools & plants, as directed by engineer in-charge : | — | — | — | — | |
| 14 | Rail section of 52Kg and above | Each | 8823.00 | 127.67 | 11,26,432.41 |
| 15 | Renewal of existing SEJ with improved SEJ with PSC sleepers under traffic block c o n d i t i o n s as per approved drawing including fixing of special size bearing plate, rubber pad and other sleeper / rail fittings, greasing to the fittings, leading rails, sleepers & fittings to site, leading and stacking of released materials within a lead of 250m, cutting of Rails, drilling of holes, fixing of related fittings, providing temporary connection with fishplates till welding of SEJ is done and sleepers shall be given initial packing to make track fit for 20KMPH speed. Note: (1) Rail cutting and hole drilling shall be paid separately. (2) One set comprise complete SEJ on both rails at SEJ. | Set | 15.00 | 9,135.77 | 1,37,036.55 |
| Assembling and Laying of Improved Switch Expansion Joint (SEJ) on PSC sleepers of any rail section as per RDSO drawing including leading of SEJ rails, sleepers, fittings for a free lead of 250 metres, cutting of rails, drilling of holes as required and lubrication of SEJ, gauging, aligning rails, providing temporary connection with adequate welding gap with adjoining rails, providing reference posts at SEJ, first through packing of SEJ portion to make track geometry fit for 30 kmph speed and making ballast profile as per IRPWM. Note: (1) Rail cutting and hole drilling shall be paid separately.(2) One set comprise complete SEJ on both rails at SEJ. | — | — | — | — | |
| 16 | Under Traffic Block Conditions | Set | 15.00 | 7,900.25 | 1,18,503.75 |
| Schedule total | ₹1,89,38,676.96 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022-uptoACS104.3.25.pdf
ATTACHMENT
General Condition
ATTACHMENT
GCCACS11_compressed.pdf
ATTACHMENT
IRGCC-2022ACS-12_.pdf
ATTACHMENT
LGH-KLYT-TRRP-45.877TKm.pdf
ATTACHMENT
Generalcondition01.04.26From01-26-27_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].