REPAIR/REPLACEMENT OF DEFECTIVE SPARES AND COMPREHENSIVE MAINT OF CRANES AND HOISTS LOCATED IN 505 ABW UNDER GE(U) PM DELHI CANTT-10.

Amount

Comprehensive preventive maintenance by technically qualified technician and rendering operationally EOT crane of capacity as mentioned below including assemblies inspection and maintenance of including checking / tightening of all nut , bolt & breaks any type any size complete system, adjusting etc of all breaks motions and VFD /VVVF drive adjustment setting of EOT / HOT cranes with having single or double girder type and providing greasing & oiling of traveling / moving parts of crane with connecting motor girder parts for movement of crane hoist / long / cross traveling and including maintaining the controlling of speed / creeping micro speed of motors with minor maint / repair electrically operated main control panel wire with connecting control wiring system consisting of main switch, step down transformer, contactor, HRC fuse, VFD, PLR, control pendent ,wire rope with break drum unit, gear box unit , oil levels, motor bed / foot ,electrical control cable, motor terminal, end cable carriage trolly , motor shaft, bush flange bearing with lathe work ,chain pulley block, ratchet clutch, gear block, chain wheel, chain etc and including locating the defect or fault and rectification of the fault and rectification of oil leakage etc any type any size and replacement of defected nut, bolt & washer and making it soundless/sound proof and after trails testing run of crane for smooth functioning / operation satisfactorily of the following mentioned capacity cranes/Hoist complete all as specified and directed by Engineer-in-Charge. Details of EOT Crane (i) EOT crane of 50 Ton capacity - 01 No. ( Make of Cranex Ltd) (ii) EOT crane of 45 Ton capacity - 01 No. ( Make of Rockwell Hoist) Total = 02 x 06 months = 12 Cranes

All as per srl item No 01 here-in-before but EOT Crane/Hoist of capacity is under mentioned complete all as specified and directed by Enginer-in-charge. Details of EOT Cranes / Hoist (i) EOT crane of 20 Ton capacity - 01 No. ( Make of Cranex Ltd) (ii) EOT crane of 20/05 Ton capacity - 01 No. ( Make of Cranex Ltd) (iii) EOT crane of 10 Ton capacity - 01 No. ( Make of Cranex Ltd) Total = 03 x 06 months = 18 Cranes

All as per Srl item No 01 here-in-before but EOT Crane/ Hoist of capacity is under mentioned complete all as specified and directed by Engineer-in-charge. Details of EOT Cranes/ Hoist (i) EOT crane of 05 Ton capacity located at 505 ABW- 10 Nos. (Make of Cranex Ltd -07Nos, Tojyam Steel- 02 Nos & Grip Engineer- 01 No.) (ii) EOT crane of 03 Ton capacity located at 505 ABW -03 Nos. (Make of Dinesh Enterprises -002 Nos & USGC -01 No) (iii) EOT crane of 02 Ton capacity located at 505 ABW – 13 Nos (Make of Cranex Ltd- 12 Nos & Grip Enterprises- 1 No) (iv) EOT Crane of 01 Ton capacity located at 505 ABW -01 No (Make of Rockwell Hoist) Total = 27.0 x 06 Months = 162.0 Months Notes applicable for srl item Nos 1 to 3 :- (i) Inspection checking decarbonising & tightning of electrical connection in total system including replacement of thimbles etc. (ii) Inspection & checking of fuses, setting & tightning the same as per their capacity. (iii) Inspection and setting of voltage system including replacement of fused indicating lamp etc. (iv) Spares for EOT crane will be measured and paid seperately as given in Section II of BOQ. (v) Contractor will carry out comprehensive maintenance once in a month for six (06) months and maintain the record of same as per the performa of monthly maintenance check enclosed in the tender documents.The same shall be forwarded alongwith RAR failing which no payment shall be released to the contractor. (vi) Contracor will ensure serviceability and safety of crane during his each visit by way of maintining job card duly signed by Engr-in-Charge and JE E/M,

Notes applicable for srl item Nos 1 to 3 (Contd.../-) (vii) The contractor will also send Technician on call basis in case of any fault. Fault to be rectified within 8hrs of receipt of complaint failing which Rs 500/- per day will be deducted till rectification of defect. (viii) Rates of all consumables such as lubricant, gear box oil, thrustor brake oil , nut bolt, split pins, bushes, gasket , Push Buttorn for pendent are deemed to be included in the quoted rates. (ix) Blank (x) The maintenance & repair under this contract shall be done through MoU issued by any one of OEM i.e. M/s Rockwell Hoisto Cranes Pvt Ltd, M/s Poineer Cranes, M/s Hercules Hoisto, M/s Turbo Fergusan (India) Pvt Ltd, M/s Dinesh Enterprises, M/s Cranex, M/s USGC, M/s Garlik, M/s Morri, M/s Hindustan Livers, M/s Grip Engineers, M/s Meta feb, M/s JPSENT. The contractor will have to submit MoU on stamp paper of Rs 100/- duly notarized, as per specified Performa within seven days of acceptance of tender, failing which the contract will be liable to be cancelled and work shall be executed as per policy in vogue. (xi) OEM’s are exempted from production of MoU, if they participate in bidding directly, subject to fulfilling requirements as mentioned in the tender. It may also be noted that, if the OEM’s issues MoU for participation of other bidder than OEM’s bid will be rejected upon his direct participation in the tendering process.

Supply , fixing, adjustment in replacement of unserviceable AC Drive / verable frequency drive (VFD)/ frequency convertor device system of capacity of 45.0 KW three phase supply system with required input 3 x AC 380-480 Volt , 50 / 60 HZ and out put 3 x AC 0-480 Volt, frequency 0-400 HZ or as per existing sample with having setting controlling devices system for operating /controlling of slow / high speed for all motion and other controlling system etc for smooth functional of over head electric traveling crane of capacity 50 Ton and including making controlling cable connection of system and testing on load complete all as specified and directed by Engineer -in-Charge.

All as per srl item No 04 here-in-before but of capacity 11.0 KW complete all as specified and directed by Enginer-in-charge.

All as per srl item No 04 here-in-before but of capacity 7.5 KW complete all as specified and directed by Enginer-in-charge.

All as per srl item No 04 here-in-before but of capacity 5.5 KW complete all as specified and directed by Enginer-in-charge.

M&L for servicing of 05 Ton Hoist crane comprising of the following:- (i) Greasing/oiling of required part ie shaft, coupling, rope drum shaft bearing etc. (ii) Checking & testing/adjustment of brakes for all the motions (iii) Checking & tightening of coupling bolts, motor foundation bolt , wheel etc. (iv) Checking the wiring connections in control panel and other accessories and to ensure that no loose/naked connection exist. (v) Checking of gear oil in gear boxes and topping oil if necessary . (vii) Cleaning of Bridge girder panel, complete

M&L for servicing of 04 Ton Hoist crane comprising of the following:- (i) Greasing/oiling of required part ie shaft, coupling, rope drum shaft bearing etc. (ii) Checking & testing/adjustment of brakes for all the motions (iii) Checking & tightening of coupling bolts, motor foundation bolt , wheel etc. (iv) Checking the wiring connections in control panel and other accessories and to ensure that no loose/naked connection exist. (v) Checking of gear oil in gear boxes and topping oil if necessary . (vi) Cleaning of Bridge girder panel, complete

M&L for servicing of 02 Ton Hoist crane comprising of the following:- (i) Greasing/oiling of required part ie shaft, coupling, rope drum shaft bearing etc. (ii) Checking & testing/adjustment of brakes for all the motions (iii) Checking & tightening of coupling bolts, motor foundation bolt , wheel aligment etc. (iv) Checking the wiring connections in control panel and other accessories and to ensure that no loose/naked connection exist. (v) Checking of gear oil in gear boxes and topping oil if necessary . (vi) Cleaning of Bridge girder panel, complete

Supply and fixing in replacement of cable resting trolly MS four wheel (with four ball Bearing) type suitable for EOT Crane or as per sample and necessary welding work complete all as specified and directed.

Supply & fixing in replacement Master Contactor 5 Step Type CMN/7 No of Contact 7 Spring Retun Type in Sheet Steel Enclosure suitable for crane operation or as per sample complete all as specified and directed.

Supply and fixing MCCB FP 400 Amp, 50 KA,415 Volts with fixed thermal and fixed magnetic setting type complete with SS enclosure box any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs all as specified and directed

Supply and fixing MCCB FP 250 Amp, 35KA,415 Volts with fixed thermal and fixed magnetic setting type complete with SS enclosure box any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs all as specified and directed

Supply and fixing MCCB FP 200 Amp, 35KA,415 Volts with fixed thermal and fixed magnetic setting type complete with SS enclosure box any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs all as specified and directed

Supply and fixing MCCB FP 100 Amp, 25KA,415 Volts with fixed thermal and fixed magnetic setting type complete with SS enclosure box any retrofit work, terminal links with thimbles, gland complete and taking down of existing MCCBs all as specified and directed

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 150-18Kg complete fitting in existing place or any necessary retrofit work complete all as specified and directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 200-18Kg complete fitting in existing place or any necessary retrofit work complete all as specified and directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 250-18Kg complete fitting in existing place or any necessary retrofit work complete all as specified and directed.

Supply and fixing in replacement of Electro Hydraulic Thrustor Brake MDT 400-46 Kg complete fitting in existing place or any necessary retrofit work complete all as specified and directed.

Supply & fixing in replacement of Electro Hydraulic Thrustor 18Kg. 3 Phase 415V AC with Hydraulic Oil complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Electro Hydraulic Thrustor 34Kg. 3 Phase 415V AC with Hydraulic Oil complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement 3 core 2.5 Sqmm PVC insulated & round sheathed bright annealed copper conductor flexible cable for voltage grade 1100 V , FRLS as per IS: 694 complete all as specified & directed by Engr-in-charge

Supply & fixing in replacement 3 core 4.0 Sqmm PVC insulated & round sheathed bright annealed copper conductor flexible cable for voltage grade 1100 V , FRLS as per IS: 694 complete all as specified & directed by Engr-in-charge

Supply & fixing in replacement 3 core 6.0 Sqmm PVC insulated & round sheathed bright annealed copper conductor flexible cable for voltage grade 1100 V FRLS as per IS: 694 complete all as specified & directed by Engr-in-charge.

Material and Labour for replacement of steel Wire Rope 10 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 complete all as specified & directed by Engr-in-Charge.

Material and Labour for replacement of steel Wire Rope 12 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 complete all as specified & directed by Engr-in-Charge.

Material and Labour for replacement of steel Wire Rope 16 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 complete all as specified & directed by Engr-in-Charge.

Material and Labour for replacement of steel Wire Rope 32 mm F.M.C Construction 6X36 ungalvanised as per IS 2266/02 complete all as specified & directed by Engr-in-Charge.

Supply /Fixing in replacement Resistence Box for 27.0 H.P. Slipring Motor RV-280, RA-47.5 made out Unbreakble Rustless Punched S.S. Grid Balance Type , 4 Step 10 Min Rating in Well Ventilated M.S. Enclosure Self Mounting Type Natural Air Cooled.

Supply /Fixing in replacement Resistence Box for 20 H.P. Slipring Motor RV-225, RA-37 made out Unbreakble Rustless Punched S.S. Grid Balance Type , 4 Step 10 Min Rating in Well Ventilated M.S. Enclosure Self Mounting Type Natural Air Cooled.

Material and labour for replacement of defective Mechanical stopper for LT Motion of crane as per sample Complete all as specified and directed.

Supply and fixing in replacement Master Contactor 4 Step Type CMN/6 No of Contact 6 Spring Retun Type in Sheet Steel Enclosure suitable for crane operation or as per sample all as specified and directed.

Supply & fixing in replacement of Step Down Transformer double bound type 415/110V AC 500VA complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Step Down Transformer double bound type 415/220V AC 1KVA complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Pneumatic Time Delay Relay 0-60 Sec Coil Voltage 110 V AC complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 25 Amp. ML-1.5 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 32 Amp. ML-2 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 40 Amp. ML-3 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 70 Amp. ML-4 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Three Pole Power Contactor 3 phase 415V AC3 110A Amp. ML-6 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC complete all as specified & directed by Engr-in-Charge.

Material and labour in replacement of Bottom Block 2 Ton Capacity 4 fall type totally enclosed hock long shunk forged steel "C" type as IS 3815, hock supporting on thrust bearing and bottom block pulley rest on suitable size ball bearing complete all as specified & directed by Engr-in-Charge.

Material and labour in replacement of Bottom Block 3 Ton Capacity 4 fall type totally enclosed hock long shunk forged steel "C" type as IS 3815, hock supporting on thrust bearing and bottom block pulley rest on suitable size ball bearing complete all as specified & directed by Engr-in-Charge.

Material and labour in of Bottom Block 5 Ton Capacity 4 fall type totally enclosed hock long shunk forged steel "C" type as IS 3815, hock supporting on thrust bearing and bottom block pulley rest on suitable size ball bearing complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Brake Shoe liner of 1 Set (02 Nos) with ribets suitable for 150mm hydraulic thrustor brake complete all as specified and directed.

Supply & fixing in replacement of Brake Shoe liner of 1 Set (02 Nos) with ribets suitable for 200 mm hydraulic thrustor brake complete all as specified and directed.

Supply & fixing in replacement of Brake Shoe liner of 1 Set (02 Nos) with ribets suitable for 250 mm hydraulic thrustor brake complete all as specified and directed.

Supply & fixing in replacement of Brake Shoe liner of 1 Set (02 Nos) with ribets suitable for 400 mm hydraulic thrustor brake complete all as specified and directed.

Supply & fixing in replacement of "Y" Brearing unit with cast Housing No. SYJ80TF complete all as specified and directed.

Supply & fixing in replacement of worn gear box foot mounting type ratio 10:1, LA11 Type A-237

Supply & fixing in replacement of Current Collector 100A with 1mtr. (Suitable for shrouded busbar) including complete fitting as per existing location all as specifed and directed .

M& L for replacement of shrouded busbar 160A Copper 4 Bar, "W" Type(RYBG)complete all as specified and directed .

Supply & fixing in replacement of 2 way lever type limit switch 2 contact type LS/2SH/2 in IP 54 Enclosure suitable for Crane or as per sample complete all as specified and directed.

Supply & fixing in replacement of Rotary type geared limit switch ratio 48:1 with 4 contacts type GRLS/48/4SE.suitable for Crane or as per sample complete all as specified and directed.

Supply & fixing in replacement of for FRLS cable PVC insulated & PVC round sheathed bright annealed copper conductor flexible cable for 16 Core 1.5 Sqmm voltage grade upto 1100 V as per IS 694/1990 of following size complete all as specified & directed by Engr-in-Charge.

Servicing of Gear Box assembly of LT/CT/Hoist complete and replacement of gear box oil seal, cover packing seal , gear box ball bearing, gear oil etc or other defected connecting parts as required at site as per existing sample/type and making it oil leak proof and sound less proof complete and including testing for 2 to 05 Ton EOT crane complete all as specified and directed by Engr -in-Charge Note- Servicing of gear box of any type and testing run work will be carried out by well qualified technician having good experience in the repairing field of EOT / HOT Cranes/Hoist or as approved by Engineer-in-Charge.

All as per srl item No 59 here-in-before but of capacity 10 to 20 Ton EOT Crane complete all as specified and directed by Enginer-in-charge.

All as per srl item No 59 here-in-before but of capacity 45 to 50 Ton EOT Crane complete all as specified and directed by Enginer-in-charge.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 15 HP, 3 phase 415 volts, with supper enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and directed by Engineer-in-Charge.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 12.5 HP, 3 phase 415 volts, with supper enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and directed by Engineer-in-Charge.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 7.5 HP, 3 phase 415 volts, with supper enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and directed by Engineer-in-Charge.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 5.0 HP, 3 phase 415 volts, with supper enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and directed by Engineer-in-Charge.

Material and labour for taking down of unserviceable motor from EOT crane and including transporting and re-winding of electric motor of capacity 3.0 HP, 3 phase 415 volts, with supper enameled copper conductor wire as per existing size/gauge including making varnishing drying and connecting fixing accessories etc including refixing on same position and testing on load complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement of Auto Phase Sequence Corrector 25 H.P 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Automatic Phase Sequence Corrector 17.5 HP 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of Automatic Phase Sequence Corrector 15.0 H.P 3 Phase 415 V. AC in CRCA Sheet Enclosure 2 mm Thick duly Powder Coated Indoor Type self standing / wall mounting complete all as specified & directed by Engr-in-Charge.

Supply & fixing in replacement of defective DC Disc Brake Type Fail Safe Brake Model SLDC 150, 75 Watt. Torge 2 KGM , 3 Phase 415 V complete fitting as per existing loaction all as specified and directed.

Supply & fixing in replacement of defective DC Disc Brake Type Fail Safe Brake Model SLDC 110, 35 Watt. Torge 1 KGM , 3 Phase 415 V complete fitting as per existing loaction all as specified and directed.

Supply & Fixing in replacement MCB 3 pole, 415V AC, 32 Amp rating 16 KA rupturing capacity, C curve complete with any retrofit work thimbles, gland as per requirement in existing panel complete all as specified and directed.

Supply & Fixing in replacement MCB 3 pole, 415V AC, 40 Amp rating 16 KA rupturing capacity, C curvecomplete with any retrofit work thimbles, gland as per requirement in existing panel complete all as specified and directed.

Supply & Fixing in replacement MCB 3 pole, 415V AC, 63 Amp rating 16 KA rupturing capacity, C curvecomplete with any retrofit work ,thimbles/lugs, gland as per requirement in existing panel complete all as specified and directed.

Supply & Fixing in replacement MCCB 4 pole, 415V AC, 63 Amp rating 25 KA rupturing capacity, complete with any retrofit work ,thimbles/lugs, gland as per requirement in existing panel complete all as specified and directed.

Supply and fixing in replacement defective Control Panel For 150 Kg. Electric Wire Rope Jib Cranes with complete electrical wiring in/out from the panel complete and Comparising the Follwing accessories complete all as specified and directed. (a) MCB 10 Amp. TP --- 1 No. (b) MCB 6 Amp. SP -- 2 Nos. (c) Step Down Transformer 415V /110V 100 VA --- 1 No. (d) AB Contactor AC3 18 Amp. with 1 N.C. Coil Voltage 110V.AC --- 4 Nos. (e) O/Load Relay suitable range ---- 1 No. (f) Suiatble Size of Contect Block --- 01 Set.

Supply & fixing in replacement of Protective Cum Control panel for 2 Ton EOT crane indoor compatmental type( CT/LT/HOIST), made out of CRCA sheet 2mm thick dully powder coated , self standing / wall mounting and complete internal wiring by PVC flexible copper cable and ferruels. Control wiring not less than 1.5sqmm and power wiring not less 2.0 Sqmm and complete incoming and outgoing cable of motors will be replacement with new cable connection and comprising the following items a). MCCB 3P 100 A, 25 KA,415 Volt : - 1Nos. b). MCB 3P 63A 415V : - 2 Nos. c). MCB 3P 16A 415V : - 3 Nos. d). MCB 2P 6-10A 230V : - 4 Nos. e) Step Down Transformer double bound type 415/110V AC 500VA - 01 No f) Contactor 3 phase 415V AC3 32 Amp. ML-2 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC : - 5 Nos. g) Contactor 3 phase 415V AC3 25 Amp. ML-1.5 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC : - 5 Nos. h) Thermal Overload relay range 6-10A suitable for ML Series contactor : - 2 Nos. i) Thermal Overload relay range 3-5A suitable for ML Series contactor : - 3 Nos. j) Thermal Overload relay range 9-15A suitable for ML Series contactor : - 1Nos. k) Single Phase Preventer 3 Phase 415V AC : - 1Nos. l) Step Down Transformer 415/220VAC 1KVA Double Bound : - 1Nos. m) Connector Block of suitable for panel . 1 Set. n) Crane operate rotory swich ON/OFF : - 2Nos.

Supply & fixing in replacement of Protective Cum Control panel for 5 Ton EOT crane indoor type, made out of CRCA sheet 2mm thick compatmental type (LT/CT/Hoist) dully powder coated , self standing / wall mounting and complete internal wiring by PVC flexible copper cable and ferruels. Control wiring not less than 1.5sqmm and power wiring not less 2.0 Sqmm and complete incoming and outgoing cable of motors will be replacement with new cable connection and comprising the following items. a). MCCB 3P 100A, 25 KA,415 Volt : - 1Nos. b). MCB 3P 63A 415V : - 2Nos. c). MCB 3P 16A 415V : - 3Nos. d). MCB 2P 6-10A 230V : - 4 Nos. e)Step Down Transformer double bound type 415/110V AC 500VA - 01 No f) Contactor 3 phase 415V AC3 40 Amp. ML-3 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC : - 5Nos. g) Contactor 3 phase 415V AC3 25 Amp. ML-1.5 with 2 N.O. + 2 N.C. Aux Contect Coil Voltage 110V AC: - 5Nos. f) Thermal Overload relay range 20-33A suitable for ML Series contactor : - 1No g) Thermal Overload relay range 14-23A suitable for ML Series contactor : - 2Nos. h) Thermal Overload relay range 3-5A suitable for ML Series contactor : - 3Nos. .i) Single Phase Preventer 3 Phase 415V : - 1No j) Step Down Transformer 415/220VAC 1KVA Double Bound : - 1Nos. K) Connector Block of Sizes. 1 Set. l) Crane operate rotory swich ON/OFF : - 2Nos.

Suman Uni Controllers