SPECIAL REPAIRS TO MAST TEST FACILITY BUILDING TEST HOUSE FOR AUXILARIES AT NAVAL DOCKYARD UNDER GE NW KUNJALI COLABA MUMBAI

Amount

Complete removal of existing water proofing treatment of any description in any position including roof tiles, PCC brick bat coba, upto any thickness cleaning, wire brushing, watering and removing of debris upto 15km or further distance as directed by Engineer-in-charge complete all as specified and as directed

Material & labour PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in roof/chajja padding for maintaining roof/chajja slope complete all as specified and as directed

Material & labour for applying oil bound primer @ 0.40 Litre/Sqm manufactured by the same agency as that of APP with density of 0.87 to 0.89 Kg/Litre at 25 degree cesius on the prepared dry roof surface and provide and lay 4mm thick APP modifed water proofing membrane reinforced with non-wooven polyster matt with physical properties as given in particular specification. The laying shall be done through authorized applicator of manufacturer as specified in particular specifications. Note : Rate inclusive of taking down and re fixing of existing lightning arrestor system including povision of new PCC block for damaged PCC block complete as directed by Engineer-in-charge

Material & labour for brushing neat cement slurry with 3Kg of cement per square metre all as specified and directed.

Material & labour for rendering 20 mm thick cement plaster in CM (1:3) on roof top surface finished even and fair including WPC by weight of 3% of total cement content complete all as specified and as directed. Note : WPC will be measured separately

Supply only integral water proofing compound

Material & labour for machine pressed chequered cement coloured tiles of size 250mmx250mmx20mm/ 300mm x 300mm x 20 mm thick mix with grey cement and pigment laid over 15mm thick screed bed in CM 1:3 set and jointed and pointedin neat cement slurry in floors complete all as specified and direcetd.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed

Providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, bed blocks, roof kerbs water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed

Taking down eaves gutters and rainwater pipes( any size or pattern) , including all fittings, heads, shoes, bends , swan necks, etc, removal to store (measured overall as fixed along the centre line over fittings and accessories).

Supply & fixing 160 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

Supply & fixing 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

Supply & fixing for PVC (SWR) bends any radius 160mm bore complete all as specified and as directed

Supply & fixing for PVC (SWR) bends any radius 110mm bore complete all as specified and as directed

Taking up or down 15mm bore steel tubing connection including cleaning for refixing or removing etc complete all as specified and as directed

Taking up or down 20 mm bore steel tubing connection including cleaning for refixing or removing etc complete.

Supply, lay, connect and test GI Tubing, medium grade with all fittings and fixed complete to wall and ceiling or laid in floor complete all as specified and directed for following sizes:-

(a) 15mm dia

(b) 20mm dia

Supply & fixing in gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed in repairs for 20mm bore complete all as specified and directed.

Supply & fixing in gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed in repairs for 25 mm bore complete all as specified and directed.

Supply & fixing in repairs 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Taking down chowkats or frames with shutter (Without taking off from frame) but n.exc 1.5 sqm complete all as specified and as directed

Taking down chowkats or frames with shutter exc 1.5 sqm but n.exc 4 sqm each but (without taking off shutter from the frame) complete all as specified and as directed

Taking down shutters of any description exc 1 Sqm but nexc 2 sqm complete all as specified and directed.

ditto as ser No 23 but exc 2 Sqm each complete all as specified and directed by EIC.

Supply & fixing aluminium window, doors with shutters / frames / partitions made out of extruded powder coasted aluminium sections, with sliding or openable shutters including frame & necessary joining cleats, glazing clip, powder coated aluminium snap beading, screws etc; complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts hooks and eyes, peg syays and handles including connected items, with and including, making good to the disturbed portion with its original specification, complete all as specified and directed. Note: for Srl item No. 4&5 :- Minimum thickness of powder coating shall be 15 micron for windows and 25 microns for doors.

Supply & fixing concealed star lock powder coated for aluminium window fixed as per manufacturers instructions all as specified and directed.

Hacking out old broken glass ( any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Supply & fixing in repairs for aluminium anodised Deco grill 7.5 mm size DG-102, fixed to F/H frames, 1.5mm th, bar size 6.2mm and 7.5mm thick in required sizescomplete all as specified and as directed by Engr-in-Charge.

Dismantling cast iron or reinforced concrete drain pipes of dia upto 100 mm jointed in cement mortar fixed to wall of high rise buildings and taking out from trenches as required.

Supply & fixing 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps all as specified and directed.

Supply & fixing 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps all as specified and directed.

Supply & fixing in repairs CI Bends100 mm bore (any radius), diminishing pieces or tapers ( larger bore measured)

Supply & fixing in repairs CI Bends 75 mm bore ( any radius), diminishing pieces or tapers ( larger bore measured)

Material & labour in repairs Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm.

Taking down PVC waste and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed by EIC

Supply & fixing 160mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with ms clamps all as specified and directed.

Supply & fixing 160mm dia bore PVC (SWR) bends any radius

Supply & fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Supply & fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed.

Supply & fixing 110 mm bore PVC (SWR) bends any radius all as specified and directed.

Supply & fixing 75 mm bore PVC (SWR) bends any radius all as specified and directed.

Taking down existing mild steel rolling shutters for and including replacing the slates, bottom lock plates, helical springs, side guides, sponge rubber gaskets, hood cover and side bracket etc wherever required and refixing in its original position after repairs including material and labour for greasing and mechanical old and new parts of rolling shutters complete all as per directed for shutters of area n. exc 20 sqm each, complete all as specified and directed.

Supply & fixing factory fabricated mild steel (hardened) helical wire spring of size 400mm long, 80mm dia to match with existing complete all as specified and directed.

Supply & fixing factory fabricated new mild steel slates of 1mm thick of grade Fe-410-0 or Fe-310-0 to match with existing fitted with locking clips, riveted to slates including one shop of red oxide primer complete all as specified and as directed

Supply & fixing factory fabricated mild steel of grade Fe-410-0 or Fe-310-0 2.5mm thick bottom lock plate riveted and made of mild steel sheet of 1mm and welded with and including provision of standard locking arrangement welded to and including mild steel angle iron complete to match with existing with and including one shop coat of red oxide primer complete all as specified and as directed

Supply & fixing factory fabricated hood cover of mild steel 1mm thick hexagonal, square or circular shape fitted to existing angle iron stiffness at bottom edge and to bracket plate all as directed and applying one shop coat of red oxide primer complete all as specified amd directed.

Supply & fixing in repair mild steel factory made bevel gear box with machine cut gears suitable for rolling shutters as fixed in repairs complete all as specified and as directed.

Supply & fixing in repair mild steel pressed beval handles 150mm long, oval type, enamelled black all as specified and as directed.

Supply & fixing mild steel safety lever lock with 4 levers for rolling shutters all as specified and as directed.

Supply & fixing for greasing and easing in position of mild steel rolling shutters of area exc 10sqm and n.exc 20sqm each for full movement and for easy operation for shutters complete all as specified and as directed. Note :- For purpose of measurement and payment EACH TIME ofgreasing and easing in position shall be considered.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar all as specified.

Taking down interlocking paver from the existing surfaces and refixing item in same place after filling depression with fine sand and re-laid the pavers over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified. Note- Punned thickness shall be measured and paid.

Material & labour for machine pressed precast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified . Note- Punned thickness shall be measured and paid.

Material & labour 18-20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed

Material & labour for machine pressed cheqered cement coloured tiles of size 250mmx250mmx20mm thick mix with grey cement and pigment laid over 15mm thick screed bed in CM 1:4 set and jointed and pointedin neat cement slurry in floors complete all as specified and direcetd.

Material & labour machine cut, mirror polished, Kota stone (greenish colour, mirror polished) slab flooring 18 to 20 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl rubbing and mirror polishing, over & incl 20mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M &L for machine cut, mirror polished, kota stone slab 18 to 20 mm thick as in skirting/vertical surfaces jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and 15 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets etc all as directed.

Supply & fixing Anodised aluminium snap grid size 605x605mm frame work for false ceiling all as specified.

Supply & fixing Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

Material & labour for false ceiling made out of 600x600x 4 mm thick (non asbestos fiber cement designer/coloured)ceiliing board / tiles deep panel.

Dismantling floor hearth or wall tiling including cement mortat bedding but not backing), removing serviceable tiles to store and rubbish off the premises.

Material & labour for Non skid coloured ceramic tiles 7 to 8 mm thick ( square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of the tiles with and including 15mm thick screed bed in CM 1:4 complete all as specified.

Material & labour for Coloured glazed ceramic tiles in vertical surface 450X350X7-8mm thick with and including 10 mm thick cm (1:4) backing coat and Triangular filliting at top of skirting, set and jointed in neat cement paste and pointed in coloured cement to match the shade of the tiles complete all as specified.

Supply & fixing in repairs vitreous china wash down water closet pan ( pedestal pattern) , white (excluding fixing bolts, flushing cistern and flush pipe) but with & including plastic seat cover of approved colour with flat bottom , and cover and mild steel chromium plated or aluminised hinging device etc complete

Supply & fixing in repairs white vitreous china squatting pan, 'Orissa' pattern, water closet of size 580x440mm with integral foot rest, P/S trap etc, fixed in repair complete all as specified and directed by Engr-in-Charge.

Supply & fixing in repairs PVC low level flushing cistern 10 Ltr capacity with complete fittings, flush pipe & float valves,handle incl brackets etc complete.

Supply & fixing in repairs white glazed earthen ware vitreous china wash hand basin of size 630x450 mm with and including CI brackets, with granite including 32mm bore brass CP waste coupling Inlet/ outlet PVC flexible pipe etc complete all as specified and directed by Engr-in-Charge.

Supply & fixing in repairs health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook (Make - Jaquar CAT PART No-ALD-CHR-585 or equivalent) complete all as specified and as directed by Engr-in-Charge.

Supply & fixing 15 mm bore dia of pipe, brass chromium plated fancy type bib tap fixed in repairs complete all as specified.

Supply & fixing in repairs 15mm size Stop Valves fancy type chromium plated screwed down high pressure with crutch or butterfly handle handle screwed both ends

Supply & fixing in repair 15 mm dia fancy type pillar tap cast copper alloy with capston heads chromium plated screwed down high pressure with or without hot or cold with long screws shanks and fly nuts screwed for iron pipes all as specified and directed.

Supply & fixing chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange, fixed in repairs.

Material & labour PVC SWR floor trap 75mm, plain with grating including setting and jointing with solvent cement

Supply & fixing of vitreous china urinal, half stall type complete including providing andfixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet ,outlet etc complete all as specified Fixed in repairs.

Supply & fixing 32mm dia PVC waste pipe for WHB and urinals fixed in repairs complete all as specified and directed.

Supply & fixing Solid PVC Door Frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed by EIC.

Supply & fixing Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M.S.frame shall be covered with heat moulded design with colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed by EIC.

Supply & fixing 2nd class hard wood (sal) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.

Supply & fixing 35mm thick factory made 2nd class HW rail & stile plain framed , panelled shutter ( two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 ( Part I), kiln seasoned and chemically pressure treated complete all as specified.

Supply & fixing 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified.

Supply & fixing in repairs Soap dish any type fixed to plugs with chromium plated brass screws complete all as specified.

Supply & fixing in repairs CP towel rail 600 mm long with round flange all as specified and directed.

Supply & fixing 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified.

Supply & fixing Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Supply & fixing aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified.

Supply & fixing Extrude aluminium anodised alloy handles, fabricated type 150mm size complete all as specified.

Material & labour for Floor door stopper of aluminium alloy body 140 mm long and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified.

Supply & fixing in repair aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc complete all as specified.

Supply & fixing mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified.

Material & labour 4 mm thick plain glass sheets ordinary quality in squares n.exc 0.5sqm each pane fixed with rubber beading for aluminium windows/doors etc all as specified and directed.

Material & labour 4 mm thick plain glass sheets ordinary quality in squares exc 0.5sqm each pane fixed with rubber beading for aluminium windows/doors etc all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge or thickness incl Nainital or similar pattern roof coverings all as specified and directed.

Material & labour for Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified.

Supply & fixing Rolled section Fe 410-W (Gde E-250 quality A) as in main and cross beams, hip and jack rafters; purlins, vertical post, plates, pipes where connected to common rafter and running rails and fixing with angle cleats or other connection plates also fixing wind tie bars etc. complete all as specified and directed.

Supply & fixing for Stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. complete all as specified.

Material & labour for prepartion of new or previously untreated steel surfaces of any description over 10cm in width or girth not otherwise describe and applying two coat of synthetic enamal paint paint oner one coat of red oxide primer complete all as specified and directed.

Taking down cement plaster or cement lime plaster on brick on stone walls etc including raking out joint, hacking for key, scrubbing down with water etc complete all as specified.

Material & labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required complete all as specified and directed.

Material & labour for rendering 10 mm thick pre polymer modified ready mixed cement based plaster on chajja top and soffits Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size and necessary two legged MS pipe scaffolding as wherever required incl curing required upto G plus 3rd floor bldg complete all as specified and directed.

Material & labour rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth (with out using extra cement) including Sagol finish complete all as specified.

Material & labour for rendering 5mm thick in CM 1:3 on ceiling surface complete all as specified and as directed

Material & labour for preparing new plastered surfaces of walls and applying two coats of oil bound distemper with priming plastered and other surfaces with alkali resistant primer with 3mm thk wall care putty on plastered surfaces complete all as specified and directed.

Material & labour preparation of new plastered surface of ceiling and applying three coat of white wash on ceiling complete all as specified and directed.

Material & labour for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necesssary scaffolding for high rise blds etc all as specified and directed.

Material & labour prepration of old plastered / decorated surfaces of walls including complete removal of existing treatment by washing, rubbing down and stopping of distempered and painted surface and applying two coat of oil bound distemper over alkaline resistant primer with 3mm thK wall care putty on wall surfaces etc complete all as specified and directed.

Material & labour for preparation of old surafces of walls and applying two coat of white wash on wall etc complete all as specified

Material & labour for preparation of old surafces of ceiling and applying two coat of white wash on ceiling etc complete all as specified

Material & labour for preparation of old wall surfaces of any description & applying one coats of acrylic (antifungal) exterior grade paint on wall/roof including necessary scaffolding complete all as specified and directed

Removing excavated material n.exc 50m and n.exc 250m and depositiing where directed at a level n.exc 1.5m above the starting point complete all as specified and as directed

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, ceiling roses, lamp holders, brackets, ,removing material to store for keeping in safe custody and making good to disturbed surfaces as directed by Engineer-in-Charge

Material & labour point wiring complete with 1.5 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make and drawn through & including PVC Conduit with Accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI make terminal boxes fixed on wall including one PVC insulated & unsheathed multistranded copper conductor 1.5 Sq. mm as earth continuity conductor connected to common earth dolly incl suitable sizes moduler boxes with cover plate for mounting the moduler switches/regulators/sockets complete all as specified.Notes: a) Colour coding shall be followed as given below:- i) Phase - Red ii) Neutral - Black iii) Earth - Green

(a) One light controlled by one 5A switch

(b) One fan point controlled by one 5A Switch

(b) One 5A flush type switch socket point on same board board

(c) One 5A flush type switch socket point on independent board

Material & labour point wiring complete with 4 Sq.mm single core multistranded PVC insulated & unsheathed copper conductors cable 1100 volts FRLS grade ISI make drawn through & including PVC caping casing with Accessories fixed on wall/ceiling/truss etc with metallic ISI make terminal boxes fix on wall including one PVC insulated & unsheathed multistranded copper conductor 4.0 Sq. mm as earth continuity conductor connected to common earth dolly for single board having 2 x 5 Amps and 1 x15 Amp switch socket point on the same board complete including moduler box and cover plate all as specified & directed. Notes:- a) Colour coding shall be followed as given below:- i) Phase - Red ii) Neutral - Black iii) Earth - Green

Material & labour for sub-main wiring with 2 runs of 1.5sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade in PVC Conduit pipe not less than 20 mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 1.5sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & labour for concealed sub-main wiring with 2 runs of 2.5sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade in PVC Conduit pipe not less than 20 mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 2.5sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material & labour for concealed sub-main wiring with 2 runs of 4 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including heavy grade in PVC Conduit pipe not less than 20 mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 2.5sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Supply & fixing modular switch 1 way 6A all as specified and directed by EIC

Supply & fixing modular switch 1 way 16A all as specified and directed by EIC

Supply & fixing modular socket, 6A - 2/3 pin combined 2 modules all as specified and directed by EIC.

Supply & fixing modular switch socket combination 16A,3 module all as specified and directed by EIC.

Supply & fixing for modular fan regulator fan step regulator, 120W - 2 modular step type

Supply & fixing ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed by EIC.

Supply & fixing in replacement of LED highbay light 150 W, min 100 lumin/watt, energy saving and envirment friendly light fitting, pressure dia cost aluminium housing with aim & adjustable bracket, matt finished reflector for gglare elimination, SMD LED with secondary lens with IP 66 protection including all fixing accessories complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair new generation 20W 4F LED battern, min 110 lumin/watt, for surface and pendent application, anodized extruded aluminium housing, high transmissitvity diffuser high lumen output complete fixing arrangement all as specified and directed.

Supply & fixing ceiling fan 1200 mm sweep BLDC , BEE 5 star rated 230 volt 50 HZ AC, having air delivery 220cum/min, 350 rpm supply single phase including accessories and connection with flexible wire three core for phase, neutral & earth including taking down old unsv fan and transport to MES store.

Supply & fixing exhaust fans in metalic body with powder coated paint , Single piece plastic blade AC Single Phase 230 V capacitor run motor of size 600 mm sweep (Heavy duty), including louvers/shutter and connecting up 3 core flexible cord of size 23/0.0076mm from ceiling rose to exhaust fan all as specified and directed.

Supply & fixing wall fan 450 mm sweep (Air circulator) rated 230 volt 50 HZ AC supply single phase PVC body including accessories and connection with flexible wire three core for phase, neutral & earth, including taking down old unsv fan and transport to MES store and making good disturbed surface.

Supply & fixing wall fan 600 mm sweep (Air circulator) rated 230 volt 50 HZ AC supply single phase PVC body including accessories and connection with flexible wire three core for phase, neutral & earth, including taking down old unsv fan and transport to MES store and making good disturbed surface.

Disconnecting & taking down old Unservicable cable & Supply laying & testing cable XLPE insulated screened, PVC bedded galvanised steel strip or wire armoured electric power cable (heavy duty) 100 volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core all as specified and directed by EIC.

Supply & fixing in repair MCB DB double door SPN 12 Way with 200 Amps rated copper bus bar .

Supply & fixing in repair MCB DB double door SPN 8 Way with 200 Amps rated copper bus bar

Supply & fixing in repair sheet metal enclosure TPN DB VTPN 6 Way,415V with 250A copper busbar, double door type IP-54, IK-09 protection suitable for housing MCCB 100Amp 4 pole all as specified and directed by EIC. Make: Siemens/Scinder/C&S Note : DBs shall be conceeled in wall where ever posible including making good the surface to match with surrounding.

Supply & fixing in replacement of MCB (SP) 6 to 32 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed.

Supply & fixing in replacement of MCB, SPN 40 TO 63 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed.

Supply & fixing MCCB 4 P 125 Amps,16KA, complete all as specified and directed.

MADHU ENTERPRIZES (BID ID -3075812)

Sachin santosh dalvi (BID ID -3074788)