GE 874/EWS-36/2022-23

Amount

B/R and E/M Portion

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15 cm thickness.

Dismantling wall and ceiling board of any discription including cover fillets.

Taking down cement plaster on stone walls etc incl racking out joints, hacking for key scrubbing down with water etc.

Dismantling of timber scantlings 40 sq cm and over in sec in any position in unframed work.

Dismantling floor hearth and wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish of the premises, complete all as directed by the Engineer-in-charge.

M &L for second class soft wood as in scantling clean sawn fixed in position.

M & L for second class soft wood as in scantling clean sawn fixed in position but except wood.

Taking down chowkhats or frame exc. 1.5sqm and n.exc. 4 sqm each with shutter (without taking out shutters from the frame).

Taking down chowkhats or frame n.exc. 1.5 sqm each with shutter (without taking out shutters from the frame).

M&L for second class soft wood plain, solid straight chowkhat and frames, wrought framed rebated on the solid rounded or chamfered, put together with glue penned and joints.

M&L plain framed paneled shutter 2nd class soft wood 35mm thick (any number of panel) with panel of timber flat on both side or of veneered particle board medium density, supplied and fitted to chowkhat.

Glazed and Skelton shutters open rebated and prepared to receive glass, gauge etc (with sash bar) edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass etc supplied and fixed to chowkhat, 30mm thick.

M&L Plain cements concrete 1:3:6 type C2 75 mm thick using 20mm stone aggregate as in plinth protection and sub base.

M&L for rendering 15mm thick on surface other than fair face of brick work or stone masonry in cement mortar 1:6 finished over and smooth without using extra cement.

M&L applying there coats of white washing including preparation of newly plastered surface of wall.

M&L sheet glass ordinary quality and glazing with oil putty in square n.exc 0.5 in each pane, 3mm thick.

S&F 250mm long aluminum alloy anodized sliding door (bolt type) and fixing clips of sheets, cast of extruded sections and fixing bolts and sliding bolts of extruded section of cast-aluminum alloy.

S&F M S butt hinges 100mm long medium weight.

S&F 200mm long aluminum alloy, anodized barrel tower bolt of extruded section.

S&F Aluminium handle, cast type, anodised 100 mm long.

S&F aluminum handles, cast type, anodized 150mm long.

S&F MS butt hinges 75mm long medium weight.

S&F 125 mm long aluminium alloy, anodised barrel tower bolt of extruded section.

M&L 6mm thick veneered decorative plywood grade 1 (with BWR resin) (06 Nos of Ply) with decorative face veneers on one face, fixed with nails to timber frame work as in ceilling type BB fixed with nails to timber frame work.

6mm thick veneered decorative plywood grade 1 (with BWR resin) (06 Nos of Ply) with decorative face veneers on one face, fixed with nails to timber frame work as in walling, complete all as specified and directed.

M&L plain fillet square, rectangular in section exc. 3 & n exc. 6 sqcm.

M&L French polishing on surfaces of any descripton width or girth including cleaning and preparing the surface including a coat of wood filler on new works two or more coats.

Dismantling boarding of any description fitted in any position with nails, complete all as specified and directed.

20mm thick second class soft wood boarding, planed one side, with butt joints and fixed with nails in facia, eaves boarding, complete, all as specified and directed.

Second class soft wood weather boarding, clean sawn, plain 20mm thick or feather edged 15mm to 20mm thick and fixed with 30mm laps, all as specified.

Two coats of synthetic enamel paint including cleaning dusting of new or previously untreated wood of ply wood base surfaces for wall, door, window, ventilator and ceiling not otherwise described over 10cm width or girth complete all as specified and as directed by Engr-in-Charge.

10 Ltr capacity PVC valveless symphonic action type flushing cistern low level white with inlet ball valve, float and handle/push including brackets and PVC flushing pipe 32mm bore, fixed in repairs, all as specified.

Bib tap cast copper alloy chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of 15mm bore (ISI marked) fixed in repairs.

Stop valve 15mm bore, cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed bosth ends for iron pipe or for unioons and fixed in repairs.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed in repairs.

500 ltr capacity rotational moulded polyethylene water storage tanks (Cylinderical vertical with closed top) and fixed in position, all as specified in SSR Part-I, including dismantling of old water tank of any description, complete all as specified and directed.

S&F 1000 (Ltrs) capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of old water tank of any discription fixed in repair.

M&L Plain cements concrete 1:4:8 type D-2 (using 40mm stone aggregate as in sub base flooring) 75mm thick.

M&L for Chequered cement concrete tiles 20 cmX20 cmX25 mm thick sat jointed and pointed in neat cement slurry in floor with grey cement and no pigments with 1:4, 25 mm thick screed bed.

Dismantling plain or corrugated steel sheeting any gauge thickness in roof covering or wall.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified.

M & L for rendering 12mm thick on surface other than fair face of brick work or stone masonry in cm 1:6 finished even and smooth without using extra cement.

Hacking out old broken glass from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work, complete all as specified and directed.

Walling of random rubble stone uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed.

Description all as per item above but except stone all as specified and directed.

M&L Plain framed paneled shutter 2nd class soft wood 30mm thick (any number of panel) with panel of timber flat on both side or of veneered particle board medium density, supplied and fitted to chowkhat.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.50 m in depth & getting out in any type of soil.

Cement concrete in foundation, filling & mass concrete type D2 1:4:8 (using 40mm graded stone aggregate).

M & L PCC 1:2:4 type B - 1 ( using 20 mm graded crushed stone aggregate) as in coping including necessary formwork, weathering, slightly rounded or chamfered angles as directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held aginst the dressed face uncoursed or brought upto courses surfaces n exc 40mm fin stone complete all as specified and directed.

Rendering 15 mm thick in cement mortar 1:4 on stone masonary surfaces or surfaces other than fair faces of brickwork and finishing even & smooth without using extra cement.

Extra for forming fair finish drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc.

Returning, filling in, including spreading, levelling, watering & well ramming in layers n exc 25 cm with any type of soil.

Removing excavated material n exc 50 m and depositing where directed at al level n. exc 1.50 m above the starting point all as directed

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in any type of soil.

M&L Brick work with sub class 'B' brick straight or curved on plan etc 6m mean radious built in cement mortor 1:6.

M&L for brick work with sub class B bricks on plan to any radius in half brick thick wall built in cement mortar 1:4.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement, complete all as specified and directed.

All as per item as above but on other then fair faces of brick work.

M&L for two coats of cement base paint over priming plastered and other surfaces with alkali resistant priming paint newly internal plastered surface of wall including preparation of surfaces.

M&L broken hard core of gauge n.exc 63mm deposited spred and leveled in layers n.exc 15cm watered and rammed to a true surface.

S&F of Roof Trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (beam, tee, angle, channel or flat sections including distance pieces, cleats etc of Fe-410-W(Gde-E-250) of quality complete all as specified and directed.

M&L RCC Design Mix M-20 as in foundations, including rafts footings foundation beams plinth beams, bases for coloumns etc basement slabs under reamed piles and mass concrete.

Form work to soffits of suspended slab, roof beam haunching grider bressumers , lintels such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (Horizontal or sloping) complete all as specified.

M&L 10 mm dia and over mild steel TMT bars, cut to length, bent to shape required cranking bending and binding with and including mild steel wire annealed not less than 0.90 mm dia.all as specified and directed.

M&L 6mm to 8 mm dia and over mild steel TMT bars, cut to length, bent to shape required cranking bending and binding with and including mild steel wire annealed not less than 0.90 mm dia. all as specified and directed.

M&L for Mild Steel handles cast type anodised 100mm long

MS barrel tower bolt, stove enamelled black, with bright bolt of 150mm long, all as specified and directed.

M&L non skid coloured Ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to mach over 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) and 15mm thick screed bed in cement mortar 1:4.

M&L non skid coloured Ceramic tiles 7 to 8 mm thick area of each tiles exceeding 0.06 Sqm but not exceeding 0.11 sqm in floors set and jointed in neat cement slurry and pointed in while or coloured cement to mach over 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) and 15mm thick screed bed in cement mortar 1:4.

Glazed ceramic coloured tiles (300mmx200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

S&F steel ventilators fixed type with glazing bars.

S&F 75mm bore PVC (SWR) pipe single socket in any length with rubber ring jointed, fixed to wall complete all as specified.

S&F 75mm bore PVC (SWR) bend or tee or radius complete all as specified.

S&F PVC gully trap square or round mouthed type (P) , size of trap 125x 110mm and jointing to drains with solvent cement in repairs complete all as specified.

S & F Waste coupling of PTMT (half or full thread ). ( Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe fixed in repairsto WHB, sink .

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors 110mm bore.

PVC (SWR ) bends any radious 110mm bore

S&F soild PVC door frame of size 50mm x 47mm made out of 5mm plaint colour PVC sheet reinforced with MS square tube, and fitted in opening all as specified.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specificating and drawing.

20mm bore Gun metal, globe or gate valves (ISI Marked), with iron wheel head, screwed both ends for iron pipe. complete all as specified and directed.

Cutting of existing steel tubing for alteration or additions and insertion of Tee 40x40x25 mm /50x50x25 mm all as specified and as directed.

GI steel water tube 25mm bore medium grade galvanised with all fittings like socket, union, elbow, bends, Tee etc and fixed complete to walls and ceiling or laid on floor.

GI steel water tube 20mm bore medium grade galvanised with all fittings like socket, union, elbow, bends, Tee etc and fixed complete to walls and ceiling or laid on floor.

GI steel water tube 15mm bore medium grade galvanised with all fittings like socket, union, elbow, bends, Tee etc and fixed complete to walls and ceiling or laid on floor.

PVC (SWR) floor trap dia of outlet 75mm with grating including jointing with solvent cement.

Angle stop valve of PTMT for 15mm bore any colour pressure screwed for iron pipe and fixed (Minimum weight 15mm -90gms)

S&F Vitreous China squatting pan "Orissa Pattern" size 580 x 440mm white with integral foot rests incl flush pipe of 32mm dia for low level cistern all as specified.

Vitreous china bowl urinal flat back, of size 465x355x265mm white (minimum), with grating and union for discharge pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including discharge pipe of PVC 32mm dia complete all as specified and directed.

S& F PVC reducer couplings fixed at outlet of urinal pot incl. 80 mm long 25 mmdia PVC Flexible pipe . ( Minimum weight 32 mm-45 gms)

Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

Pillar tap 15mm bore cast copper alloy, with capstain head chromium plated screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed both ends for iron pipe or for unions and fixed

S&F Soap dish,any type, fixed to plug with chromium plated brass screw

M&L Lagging to pipes 20mmdia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842

M&L Lagging to pipes 15mmdia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed 'SNAP ON' pipe sections of density 144 kg/cum conforming to IS-9842

Applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new or previously untreated wood surfaces over 10cm width or girth, complete all as specified and directed by Engr-In-Charge.

Construction of Septic tank excavation in ordinary soil, foundation in PCC 1:2:4, brick work in CM 1:4, RCC slab covers incl RCC precast manhole cover having 6mm plate embedded all around /fibre reinforced cover with angle iron frame vent shaft and sludge chambers etc complete for 10 users.

Supply and fixing for salt glazed stone ware drain pipes, laid in trenches and jointed as specified 150mm bore pipe.

M&L for cement concrete bed (1:3:6) type C-2 using 40mm graded stone aggregate to drain pipes of 150mm bore including packing under hunching against the site of pipe after they are laid and tested.

Construction of Soakage well excavation in ordinary soil, foundation in PCC 1:3:6, well of Honey Cambed and solid in M-25 concrete, including intercepting chamber, screen chamber Brick work in CM, RCC cover slab in M-25 filling with brick bats of size 1.80 m dia and 3.0 m deep.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Point wiring with 1.5 Sq mm multi standerd insulated copper conductor single core PVC insulated cable 1100 volt including casing and caping for one light point controlled by one switches including 2nd class hard wood rectangular block open recessed cover with 3mm thick plastic laminated sheet cover incl PVC insulated 1.5 Sqmm copper conductor as earth wire for one light controlled by one switch completed all as specified and directed.

All as per item above but for 3-pin socket out let 5 Amps on same board with other switches with continous PVC insulated copper conductor cable 1.5 Sqmm earth wire.

All as per item above but for 3-pin socket out let 5 Amps on independent board with other switches with continous PVC insulated copper conductor cable 1.5 Sqmm earth wire.

All as per item above but for 3-pin socket out let 15 Amps on independent board with 4 Sqmm Multi std.copper conductor PVC insulated cable 1100 volts grade with continous continous 2.5 Sqmm earth wire.

Supply and fixing of lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings suitable for LED bulb 7 watt. Make : Havells/Anchor/Siska/Philips/Bajaj

Supply and LED 7 Watt Bulb with B22 pin, of make Havells/ Syska/ Philips, suitable for fixing in holder as above

M&L for LED Batten 1x20 W for regal batten for LED Universal battenm for G13 with 18 W rods and ultra bright LED Polycarbonate tube light very high effiency suited for instalation in existing T8 and connecting electrically using PVC insulated and overall sheated flexible copper conducter cable of size 0.75 sqm 3 core all as required at site or directed by engr - in- charge. Make : Havells Batten Cap part No LHFYBYG21N1W020 and LED Tube Rod Cat part LHLDCLXNUL8X018 or Equivalent.

Supply and fixing LED light fitting, 1x9 W bulk head luminaries, with lamp holders, etc. complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ. Make : Bajaj/Havells/Anchor/Philips

S&F Switch piano flush type 6 Amps single pole one way. Make : Havells/Anchor/Philips

S&F ceiling rose surface bakelite 65x50mm two to three terminals (ISI Marked). Make : Havells/Anchor/Philips

S&F socket outlet 2-in-1, 3 pin, 6 Amps flush type (ISI Marked) complete all as specified and as directed by Engr-in-charge. Make : Havells/Anchor/Philips

S&F Switch socket combination 5 in 1, 5 and 15 Amp universal type controlled by by one switch (ISI Marked). Make : Havells/Anchor/Philips

S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall, surfaces all as specified and directed. Make : Havells/lEGRAND/SSK.

S&F RCBO, Single pole and Neutral 240 Volts, 50 H 32 Amps, 30mA all as specified and as directed.

S&F MCB's single pole 240 volts 6 to 32Amps 10 KA 'B' series, all as specified and as directed by Engr -in-Charge. Make : Leggrand/Havells/HPL.

Supply and fix water heater storage type, electric capacity 25 litres, 2 KW capacity, with copper inner tank, BEE 5 star rated, with copper/glass lined stainless steel tank,along with associated plumbing, mechanical and electrical fittings instructed by Engr-in-Charge. Make-Havells/Recold/Usha.

S&F 1100 volt grade heavy duty cable PVC insulated multistranded aluminum stranded conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat of circular of size 10 Sqmm complete all as specified and as directed by Engr-in-Charge. Make : Havells/Anchor/Polycab/Plaza.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) connected to galvanized iron wire 4mm dia by means of bolts, nuts and washers of galvanized iron or steel, GI light grade protection pipe 15mm dia, GI medium grade water pipe 20mm dia with funnel all as shown in electric plate No 3 of SSR-2009 pt-I and testing complete including earth work in any type of soil PCC 1:2:L4 as in earthing pit CI pit cover 5.5mm thick common salt charcoal all as specified.

patriotic builders

Bidder Name

patriotic builders

M/S MANZOORAHMAD LONE