REPAIR / MAINT AND CLEANING OF SUBMERSIBLE PUMPS, PANELS AND ALLIED WORKS AT AYODHYA CANTT

Amount

Lifting of defective submersible pump set of any make & model of capacity 25 HP to 45 HP from deep well 350mm housing along with connected accessories such as column pipe of 150mm dia , submersible cable, steel pipe, spider, sleeve, line shaft, nut, bolts etc complete all as specified and directed by Note:- All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate

Transportation including loading & unloading of defective submersible pump set 3 phase of any make and capacity 25 to 45 HP from pump house to work shop for necessary repair and transporting back to the pump house including carefully loading & unloading of pump set after repair complete all as specified and directed by Engr-In-Charge.

Dismantling of defective submersible pump set of any make & model of capacity 25 HP to 45 HP, repairing the same including replacing old U/S parts and re-assembling and testing after repair complete all as specified and directed by Engr-In-Charge. Note: (i) All the spares required for repair will be measured and paid seperately as supply only. (ii) Greasing of moving parts deemed to be included in the quoted rate

Supply only CI/ MS bowl (As per existing size) for submersible pump capacity 25 HP to 45 HP any make & model complete all as specified and directed by Engr-in-charge.

All per Srl Item No. 4.00 but stainless steel shaft with key

All per Srl Item No. 4.00 but Gun Metal/rubber bush

All perSrl Item No. 4.00 but Stainless steel sleeve

All perSrl Item No. 4.00 but Sand Guard

All per Srl Item No. 4.00 but Impeller lock with key

All per Srl Item No. 4.00 but Neck ring (as per existing size and type)

All per Srl Item No. 4.00 but Turning & polishing of Pump shaft (lathe work)

Supply only Stainless Steel thrust bearing. parts for submersible motor of capacity 25 HP to 45 HP any make & model complete all as specified and directed by Engr-in-charge.

All per Srl Item No.12.00 but Carbon plate.

All per Srl Item No.12.00 but Rotor Gun Metal / steel bush

All per Srl Item No.12.00 but Rubber bush

All per Srl Item No.12.00 but Upper housing

All per Srl Item No.12.00 but Lower Housing

All per Srl Item No.12.00 but Turning, polishing of Rotor & shaft (Lathe work)

Rewinding of submersible motor capacity 25 HP to 45 HP any make & model with super enamelled copper wire of existing size including removal of existing burnt winding, cleaning of slots including packing material, connection and testing complete all as specified and directed by Engr-in-Charge.

M&L for painting to pump set with two coat of synthetic enamel paint (grey colour) over a coat of red oxide primer after preparation of surface complete all as specified and directed by Engr-in-Charge.

Lowering, connecting, commissioning testing of repaired submersible set any make and capacity 25 HP to 45 HP 3 phase 415V into bore well 300/200mm with connected items such as column pipe approx 40 RM, properly connecting submersible cable etc complete all as specified and directed by Engr-in-Charge. Note:- All type of T & P, chain pulley & tripod etc required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 20 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling belt, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-in-Charge. Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 10 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-in-Charge. Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Repair and maintenance of defective Monoblock motor pump any make & model of capacity 7.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing complete all as specified and directed by Engr-in-Charge. Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

Repair and maintenance of defective Monoblock motor pump any make & model of capacity upto 2.5 HP including required repairing like motor rewinding, replacement of minor spares like Motor bearing, Gland packing, Fan motor blade, Packing paper, Water seal, Starting Coil, Motor housing, S.S . sleeve repairing on Lathe ,Impeller Brass, Gun Metal Bush, Rubber Coupling Set, Rubber bush, Rubber gasket, nut bolt & any other minor connected items and testing after repairing including painting complete all as specified and directed by Engr-in-Charge. Note: All type of T&P including dismantling and fixing required at site will be arranged by the contractor and rates for the same deemed to be included in the quoted rate.

S&F 3 pole power contactor MNX 70, 220/440 volts with 70 Amp AC3 duty rating any type including auxillary switch of make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F 3 pole power contactor MNX 50, 220/440 volts with 50 Amp AC3 duty rating any type including auxillary switch of make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F MCCB 4 pole 100 Amp, 415 volt, of make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F electronic timer for automatic star delta starter 415 volt 50 Hz 3 - 30 sec of make: L&T, in existing panelincluding taking out of old one all as specified and directed by Engr-in-Charge.

S&F Single phase Preventer Relay with adjustable time delay 30 sec to 5 min suitable for 415 volt AC, any type of make: L&T or equivalent including internal wiring from switchgear to relay in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F flat three core submersible cable PVC insulated and sheathed multistranded copper conductor of cross sectional area 16 sqmm all as specified and directed by Engr-in-Charge.

S&F in replacement of lead acid battery 12 volt 180 Ah including initial charge of make: Exide or equivalent complete all as directed by Engr-In-Charge

S&F On load Changeover 4 pole 100 Amp, 415 volt, open execution type of make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F digital type Voltmeter with LED display suitable for 3 phase of make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F digital type Ammeter with LED display suitable for 3 phase make: L&T or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F tape wound ring type Current Transformer suitable for Bar primary of rating 100/5 Amp, burden 5 VA of make: Kappa/ Matrix or equivalent in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F overload Relay any type suitable for 5 Amp to 30 Amp type ML 415 volt AC of make: L&T or equivalent including internal wiring from switchgear to relay in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F overload Relay any type suitable for 32 Amp to 88 Amp type MPR of make: L&T or equivalent including internal wiring from switchgear to relay in existing panel including taking out of old one all as specified and directed by Engr-in-Charge.

S&F Indicator lamp LED type (R,Y,B) complete with bakelite fuse complete including taking out of old one all as specified and directed by Engr-in-Charge.

S&F ON and OFF push button flush head type (Red,Green) complete including taking out of old one all as specified and directed by Engr-in-Charge.

M&L for copper lugs 16 sqmm complete including taking out of old one all as specified and directed by Engr-in-Charge.

S&F Three phase submersible pump controller with single phase preventer of rating 3 phase, 415V, 50 HZ, 40 HP, Type MU-G40 FASD, of make L&T, Sceinider or equivalent including taking out of old one all as specified and as directed by Engr-in-Charge.

Taking down existing earthing of any description and M&L for new earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected with GI strip 25x4mm by means of bolts, nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI strip is connected to the equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6) type C1 in chamber of size not less than 300x300x300mm (internal diamentions) with 50mm thick cement concrete cover made of PCC (1:2:4), type B-1, the chamber shall be constructed at 1m away from earth pit complete all as specified and directed by Engineer-in-Charge.

Disconnecting electrically incomming and outgoing LT UG cable of LT panel of any size and replace burn/unsv suitable size of aluminium bus bar, Welding work for hinches and doors, fixing the locking arrangement including scraping outdoor/indoor side of LT Panel and one coat of redoxide, two coat of synthetic enamelled seimens gray spray of outdoor/Indoor side and reconnecting LT UG cable with fixing aluminium lugs by using crimping tool, nut, bolt washer etc and all necesary work required for smooth functioning of LT panel all specified and directed by Engr-in-Charge.

Taking out unserviceable sluice valve150 mm bore from water mains all as specified and directed by Engr-In-Charge

S&F connection & testing sluice valve 150 mm bore 'ISI marked' both ends flanged and drilled cast iron body class PN-1.6 conforming to IS-14846/2000 complete with gun metal spindle including necessary nut bolts and gasket etc for fixing and taking out of old valve complete all as specified and directed by Engr-In-Charge of the following sizes :-[Note: For sluice valves fixed with pillars of over head tank, breaking of RCC/lead/ flange joints and repairing the same after fixing of valve deemed to be included in the quoted rates]

M&L for replacing of gland packing,nut-bolts and washer of sluice valve of 150 mm bore complete all as specified and directed by Engr-in-charge.

All as per item no. 49.00 but 100 mm bore.

M&L for replacing of gun metal check nut of sluice valve of 150 mm bore complete all as specified and directed by Engr-in-charge.

All as per item no. 51.00 but 100 mm bore.

M&L for replacing of existing size gun metal spindle of sluice valve of 150 mm bore complete all as specified and directed by Engr-in-charge.

All as per item no. 53.00 but 100 mm bore.

M&L for rolled mild steel work as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. for repair to staircase,hand rails,back rest of over head reservoir, gate, shed of generator set & panel, etc or as specified and directed by Engr-in-Charge. Note: All T&P including welding machine and labour charges for working on OH tanks upto 21 mtr high staging deemed to be included in the quoted rate

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 500MPA as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

K R KAUSHAL AND SONS

His And Her Enterprises

disha construction

Khan Brothers