REPAIR/REPLACEMENT OF LT PANEL BUS BAR LIGHTING CONDUCTOR AND VARIOUS ITEMS IN COD INSIDE OF AGE E/M UNDER GE (I) KANPUR.

Amount

Excavation in trenches in any type of soil n exc 1.5 mtr in width and n. exc 1.5 mtr in depth and getting out all as required for laying of cables,foundation filling of poles or stays and for rerouting of cables.

Returning filling, in including spreading ,leveling, watering and well ramming in layers not exc 25 cm each all as required.

Removing excavated material to a distance not exceeding 50 meters and depositing where directed at a level not exc 1.5 mtr above the starting point.

M&L for sand cushioning to under ground cables 8 cm thick before laying the cable and 15 cm, thick after laying, stretching and testing the cable

M&L for Sub class ‘B’ bricks old size. laid dry flat over the cable abutting each other, length of cable equal to width of brick all as required.

M & L for replacement of existing unserviceable LT panel, Installation, commissioning and testing of new LT panel cubical type suitable for outdoor installation factory made CPRI approved of suitable size,dust & vermin proof fabricated out of 3.15 mm thick CRCA sheet duly powder coated with cable entry & exit with suitable size of glands, terminals & thimbles all as specified , duly mounted on angle iron frame of sjuitable size fixed on RCC/PCC block fixed with grounded bolts & nuts and washers including rating copper bus bar not less than 50X5 mm suitable for 400 Amps for 3 phase 4 wire mounted on epoxy based post insulators with suitable size of CTs,LED indicator lamp set type RYB (indicator lamps should display colour of phase as well as phase volatge complete) of make AE/Legrand/L&T, complete internal wiring with suitable size of copper conductor PVC insulated and sheathed cable front and rear openable double door with locking arrangement, angle iron frame made out from suitable size and making good all disturbed surfaces of floor/wall using RCC/PCC work as required at site complete all as required at site or directed. Make of Panel : L&T/SIEMENS//C&S/ABB/Legrand/SCHNEIDER/HAVELLS) (Panel and its switchgear i.e MCCB/MCB SHALL BE OF SAME MANURACTURES) INCOMMER (i) MCCB 3 Phase, 4 Pole 250 Amps,35/36kA rupturing cap,415 volts 50 Hz AC supply - 01 Nos (ii) Digital voltmeter 0 to 500 volt - 01 Set (iii) Digital ameter 0 to 250 amp - 01 Set (iv) Phase indicating lamp RYB with indicating voltage in digital LED format ( set of three) - 01 Set OUTGOING (i) MCCB 3 Phase, 4 Pole,160 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos (ii) MCCB 3 Phase, 4 Pole,100 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos (iii) MCCB 3 Phase, 4 Pole,63 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos

M & L for replacement of existing unserviceable LT panel, Installation, commissioning and testing of new LT panel cubical type suitable for outdoor installation factory made CPRI approved of suitable size,dust & vermin proof fabricated out of 3.15 mm thick CRCA sheet duly powder coated with cable entry & exit with suitable size of glands, terminals & thimbles all as specified , duly mounted on angle iron frame of sjuitable size fixed on RCC/PCC block fixed with grounded bolts & nuts and washers including rating copper bus bar not less than 60X10 mm suitable for 900 Amps for 3 phase 4 wire mounted on epoxy based post insulators with suitable size of CTs,, LED indicator lamp set type RYB (indicator lamps should display colour of phase as well as phase volatge complete) of make AE/Legrand/L&T, complete internal wiring with suitable size of copper conductor PVC insulated and sheathed cable front and rear openable double door with locking arrangement, angle iron frame made out from suitable size and making good all disturbed surfaces of floor/wall using RCC/PCC work as required at site complete all as required at site or directed. Make of Panel : L&T/SIEMENS//C&S/ABB/Legrand/SCHNEIDER/HAVELLS) (Panel and its switchgear i.e MCCB/MCB SHALL BE OF SAME MANURACTURES) INCOMMER (i) MCCB 3 Phase, 4 Pole 630 Amps,35/36kA rupturing cap,415 volts 50 Hz AC supply - 01 Nos (ii) Digital voltmeter 0 to 500 volt - 01 Set (iii) Digital ameter 0 to 630 amp - 01 Set (iv) Phase indicating lamp RYB with indicating voltage in digital LED format ( set of three) - 01 Set OUTGOING (i) MCCB 3 Phase, 4 Pole,250 Amps,25 kA,415 volts 50 HZ AC supply - 02 Nos (ii) MCCB 3 Phase, 4 Pole,160 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos (iii) MCCB 3 Phase, 4 Pole,63 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos

M & L for replacement of existing unserviceable LT panel, Installation, commissioning and testing of new LT panel cubical type suitable for outdoor installation factory made CPRI approved of suitable size,dust & vermin proof fabricated out of 3.15 mm thick CRCA sheet duly powder coated with cable entry & exit with suitable size of glands, terminals & thimbles all as specified , duly mounted on angle iron frame of sjuitable size fixed on RCC/PCC block fixed with grounded bolts & nuts and washers including rating copper bus bar not less than 40X10 mm suitable for 600 Amps for 3 phase 4 wire mounted on epoxy based post insulators with suitable size of CTs, LED indicator lamp set type RYB (indicator lamps should display colour of phase as well as phase volatge complete) of make AE/Legrand/L&T, complete internal wiring with suitable size of copper conductor PVC insulated and sheathed cable front and rear openable double door with locking arrangement, angle iron frame made out from suitable size and making good all disturbed surfaces of floor/wall using RCC/PCC work as required at site complete all as required at site or directed. Make of Panel : L&T/SIEMENS//C&S/ABB/Legrand/SCHNEIDER/HAVELLS) (Panel and its switchgear i.e MCCB/MCB SHALL BE OF SAME MANURACTURES) INCOMMER (i) MCCB 3 Phase, 4 Pole 400 Amps,35/36kA rupturing cap,415 volts 50 Hz AC supply - 01 Nos (ii) Digital voltmeter 0 to 500 volt - 01 Set (iii) Digital ameter 0 to 250 amp - 01 Set (iv) Phase indicating lamp RYB with indicating voltage in digital LED format ( set of three) - 01 Set OUTGOING (i) MCCB 3 Phase, 4 Pole,160 Amps,25 kA,415 volts 50 HZ AC supply - 02 Nos (ii) MCCB 3 Phase, 4 Pole,100 Amps,25 kA,415 volts 50 HZ AC supply - 01 Nos (iii) MCCB 3 Phase, 4 Pole,63 Amps,25 kA,415 volts 50 HZ AC supply - 02 Nos

M & L for replacement of existing unserviceable LT panel, Installation, commissioning and testing of new LT panel cubical type suitable for outdoor installation factory made CPRI approved of suitable size,dust & vermin proof fabricated out of 3.15 mm thick CRCA sheet duly powder coated with cable entry & exit with suitable size of glands, terminals & thimbles all as specified , duly mounted on angle iron frame of sjuitable size fixed on RCC/PCC block fixed with grounded bolts & nuts and washers including rating copper bus bar not less than 50X5 mm suitable for 400 Amps for 3 phase 4 wire mounted on epoxy based post insulators with suitable size of CTs, LED indicator lamp set type RYB (indicator lamps should display colour of phase as well as phase volatge complete) of make AE/Legrand/L&T, complete internal wiring with suitable size of copper conductor PVC insulated and sheathed cable front and rear openable double door with locking arrangement, angle iron frame made out from suitable size and making good all disturbed surfaces of floor/wall using RCC/PCC work as required at site complete all as required at site or directed. Make of Panel : L&T/SIEMENS//C&S/ABB/Legrand/SCHNEIDER/HAVELLS) (Panel and its switchgear i.e MCCB/MCB SHALL BE OF SAME MANURACTURES) INCOMMER (i) MCCB 3 Phase, 4 Pole 250 Amps,35/36kA rupturing cap,415 volts 50 Hz AC supply - 01 Nos (ii) Digital voltmeter 0 to 500 volt - 01 Set (iii) Digital ameter 0 to 250 amp - 01 Set (iv) Phase indicating lamp RYB with indicating voltage in digital LED format ( set of three) - 01 Set OUTGOING MCCB 3 Phase, 4 Pole,63 Amps,25 kA,415 volts 50 HZ AC supply - 05 Nos

Supply , Installation ,testing & Commissioning of LT Panel Board in replecement indoor Type of suitable Size as per IS mounted on angle iron legs imbedded in PCC 1:4:8 block type D-2 (using 40 mm graded aggregates) at pump houses , floor mounting ,dust and vermin proof factory made, fabricated out of 2 mm thick CRCA sheet suitable for 3 Phase , 415 Volt 50 HZ AC Supply , Copper busbar 200 Amp with size not less than 40X5 mm for 3 Phase and 4 wire system duly insulated with heat shrinkable sleeve as per colour supported on epoxy insulator 01 set common earth bus at bottom inside panel board with two earth terminal out side panel board ,cable alley cable gland with independent plate at bottom and complete panel board painted with powder coating Grey colour including taking down complete, with Phase Indiactors reflecting color alongwith digital display complete. THE MOTOR IS PROTECTED AGAINST VARIOUS FAULTS AND CONDICTIONS SUCH AS OVERLOAD,UNDERLOAD, OVER AND UNDER VOLTAGE, START UP DELAY, OVER AND UNDER FREQUENCY, SINGLE PHASING, PHASE REVERSAL, UNBALANCED PHASE, LOCK ROTOR, EARTH FAULT PROTECTION, PHASE SEQUENCE PROTECTION ETC. all as specified and as directed. Make of Panel : L&T/SIEMENS//C&S/ABB/Legrand/SCHNEIDER/HAVELLS) (Panel and its switchgear i.e MCCB/MCB SHALL BE OF SAME MANURACTURES) INCOMMER MCCB 125A 4 POLE 25kA -01 Nos THERMAL MAGNETIC TRIP FOR O/L, S/C PROTECTION ONLOAD CHANGEOVER SWITCH 4POLE 125AMP -01 Nos Make : L&T/Legrand/Concerned panel make DIGITAL MULTIFUNCTIONAL METER (WL 4410- Make :L&T/Legrand/Concerned panel make RYB PHASE INDICATORS with digital indication of Voltage -03 Nos ON/OFF INDICATOR- 2 Nos ON/OFF PUSH BUTTONS -02 Nos SOFT STARTER (PSE) FOR 40HP/30kW HEAVY DUTY STARTER, SOFT STARTER HAS VARIOUS FEATURES SUCH AS- BUILT IN BYPASS, DISPLAY AND KEYPAD, TORQUE CONTROL, SETTABLE CURRENT LIMIT FUNCTION, Make : ABB/Legrand/Seimens/Concerned panel make NOTE: Contr must have arragnements for repair,maint & caleberation for soft starter when needed as per contract provisions. LINE CONTACTOR 95Amp 3Pole- 01 Nos L&T/Legrand/Seimens/Concerned panel make SEMI CONDUCTOR FUSES 125AMP AS required ADVANCED MOTOT PROTECTION RELAY -01 nos TNC OPERATION SWITCH -03 nos make : L&T/HOTLINE/Concerned panel make CTs 125/5A, 15VA BURDEN, CL-1 -03 Nos Make : AE/NIPEN/Concerned panel make

M & L for providing earthing with GI earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level ) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 32 x 6 mm thick for earthing lead fixed by means of nuts,bolt,washers etc.of copper / brass connected to earth test point complete all as specified in electrical plate NO 3 of SSR 1996 part 1 ,including necessary excavation and earth work in any strata of soil,GI water pipe with 20mm dia.funnel &wire mesh PCC pit with CI cover and frame etc all as specified and directed by Engineer-in-charge. Note:- All the joints shall be made with welding to get proper conductivity.

M & L for fixing earthing strip 32 x 6 mm GI strip fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required, In Repair,complete all as specified & directed.

Supply & Fixing in replecement air ventilator iron body 200/220/250 mm sweep complete with fitting s & connections to wall complete all as per directed by Engr-in-charge Make : Usha/Crompton/Havells

Supply and installation, connecting eclectically & commissioning in replacement of LT feeder pillar box outdoor type of suitable size,factory fabricated made out of MS sheet of thickness 3.15 mm front door openable with locking arrangement mounted on angle iron legs made out of angle iron of size 40x40x6mm, 1.5 mtr long, 1.0 mtr above ground level and 0.50 mtr embedded in PCC blocks of suitable size,duly painted with two coats of synthetic enamel paint over a coat of red oxide complete with 300 amps rated copper bus bar suitable for 3 phase 4 wire supply system duly drilled holes and making all cable connection with proper thimbles mounted on epoxy based post insulators and one MCCB 200 Amps 4 pole 415 Volt, 35/36 kA of make : Legrand/ Schneider/Havells/L&T complete all as required at site.

Supply and laying in trenches or fixing to wall/pole or passing through pipe in replacement of XLPE insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 50 Sqmm 3.5 core complete including taking out old unsv cable of any type,make & cap.Make of cable Havells/Grandlay/kalinga/Polycab. (Note : Incl making good all distributed wall surfaces/ flooring/tilling to match with existing specification)

Supply and laying in trenches or fixing to wall/pole or passing through pipe in replacement of XLPE insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 16 Sqmm 4core complete including taking out old unsv cable of any type,make & cap.Make of cable Havells/Grandlay/kalinga/Polycab. (Note : Incl making good all distributed wall surfaces/ flooring/tilling to match with existing specification)

Sagar Electricals

S B ENTERPRISES

VEE KAY ENTERPRISES

BHARAT ASSOCIATES PVT LTD