GE U(N) 37 2023 24 PROVN OF ADDTN ALT TO BLDG NO NP 11 INCLUDING SPECIAL REPAIR TO BLDG NO P 38 UNDER AGE BR II OF GE (N) UDHAMPUR

Amount

M&L for preparing RCC roof slab top by wire brushing and cleaning the dust and forign material etc complete and applying a coat of hot blown bitumen 85/25 grade @ 1.2 kg per Sqm over coat of bitumen @ 0.30 Sqm and there after laying of a layer of APP based polymenic membrane (live layered with centrre core as 100 microns, high molecular high density ployethylene film) minimum weighing 3 kg/Sqm and reinforced with polyster non woven fabric (wt. not less than 150 gms/Sqm laid on bituminous surface by press application method with 75 mm side overlap and 150mm end overlap the membrane has to be laid with LPG torch application and overlaps sealed and finished neat, after taht applying one coat of bitumen 85/25 grade on top surface @ 1.02 kg/sqm and blinded with primer incl dismantling existing roof treatment complete all as specified and directed by Engr in Charge. NOTE : Water proofing work shall executed only by authorised applicator labours documents of the same will be deposited by contractor to concern Engr-in -charge and then same will be submitted along with payement to E8 section.Please note no payement shall made if the work was executed by non authorized labour by the applicator.

M&L for two coats of aluminium paint on roof padding surfacescomplete all as specified and directed by Engr in Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces cm (1:4) even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M&L for taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc, but cement or cement lime plaster, any description complete all as specified and directed by Engr in Charge.

M&L for rendering 10 mm thick on fiar faces of brick work of concrete surfaces with cm (1:6) even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces cm (1:4) even and smooth without using extra cement complete all as specified and directed by Engr in Charge.

M&L for rendering 5 mm thick in cm 1:3 on ceiling finished even & smooth W/O using extra cement .complete all as specified and directed by Engr in Charge.

Supply only integral water proofing compound of approved quality, ISI Marked, complete all as specified and directed by Engr in Charge.

M&L two coats of oil bound distember over a coat of primer over two coats of approved 3mm wall care putty over and including preparation of new plastered surfaces of wall complete complete all as specified and directed by Engr in Charge.

M&L for three coat of white wash on new surface of ceiling complete all as specified and directed by Engr in Charge.

M&L for two coat of cement base paint over newly plastered surfaces of wall including one coat of primer and preparing surfaces complete all as specified and directed by Engr in Charge.

All as per item 11 above but on ceilings complete all as specified and directed by Engr in Charge.

M&L for demolition unreinforced cement Concrete of any description complete all as specified and directed by Engr in Charge.

M&L for taking down chowkat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each complete all as specified and directed by Engr in Charge.

All as per item no 14 above but exceeding 1.5 Sqm and not exc 4 Sqm each complete all as specified and directed by Engr in Charge.

M&L for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, complete all as specified & directed by Engr in Charge.

M&L for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified & directed by Engr in Charge. .

M&L for providing cement concrete 1:3:6 type C-0 using 12.5mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified & directed by Engr in Charge. .

S&F Aluminum anodised bolts barrels tower bolts with bright both 150mm long complete all as per specified .

S&F aluminium alloy ,anodised,sliding door bolt 300 mm length with hasp,staple (bolt type) and fixing clip of sheet,cast or etruded sections and fixing bolts and sliding bolt of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engr in Charge.

S&F alunminium handle cost type 150mm long oval type complete all as specified and directed by Engr in Charge.

M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed by Engr in Charge. .

M&L for preparation of new steel and iron surfaces exceeding 10cms width or girth and applying two coats of synthetic enamel paint over preprimered surface complete all as specified & directed by Engr in Charge. .

M&L for preparation of old steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete spray painting complete all as specified and directed by Engr in Charge.

M&L for hacking out old broken glass ( any thickness, size, quality or description ) from wooden or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed by Engr in Charge.

M&L for sheet galss 5.5mm wired glass exc 0.5 Sqm each with glazing putty with glazing pins including taking down old glass and cleaning the frame complete complete all as specified and directed by Engr in Charge.

M&L for repair to steel rolling shutter including greasing, ball bearing, top cover, anchoring rod hasp & staple with safety lever cocks and manual type but gear operated type with bevel gear box and crank handle etc complete all as specified and directed by Engr in Charge. .

M&L for 3.0 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane including taking out old broken glass any thickness any size quality are description from wooden frames or stone, concrete or brick from glazed with putty are fixed with beads complete all as specified and directed by Engr in Charge.

M&L for dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiles to store and rubbish off the premises, complete complete all as specified and directed by Engr in Charge.

M&L for 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and smooth with using extra cement complete all as specified and directed by Engr in Charge.

M&L for coloured vitrified tiles (double charged square) of 10mm thick any colour (area of each tile exceeding 0.38 sqm not exceeding .64 sqm minimum size 800mm X 800 mm) as in floors jointed in cement slurry and pointed in white or coloured cement to match the existing surfaces, laid over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed by Engr in Charge.

M&L for glazed ceramic coloured tiles 450 mm x 300 mm x 7mm thick as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, including 10 mm thick rendering in cement mortar 1:4complete all as specified and directed by Engr in Charge.

M&L for non skid coloured ceramic tiles area of each tile exc 11 sqm but n exc 18 sqm 7mm to 8mm thick as in floor finishes set and joined in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, including 10 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed by Engr in Charge.

M&L for granite stone slab 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of marble laid over & including 10 mm thick rendering/screed bed in CM (1:3) complete all as specified and directed by Engr in Charge.

M&L for machine cut kota stone slab flooring 18-20mm thick over 20 mm thick cement screed in CM 1:3 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed by Engr in Charge.

Ditto but on skirting including screed of 10 mm thick in CM 1:4 complete all as specified & directed by Engr in Charge. .

M&L for providing 50 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection even and smooth with using extra cement complete complete all as specified and directed by Engr in Charge.

M&L for 75mm thick plain cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base of flooring etc, complete all as specified and directed by Engr in Charge.

M&L for 60mm thick, factory made machine pressed interlocking paver blocks of any shape and size with M-35 design Mix concrete of any approved colour using grey cement and pigment conforming to IS 15658-2006 including sand cushioning not less than 50mm thick complete all as specified and directed by Engr in Charge.

M&L for chequered cement concrete tiles coloured, 25 cm x 25 cm x 25 mm thick , machine pressed ; set and jointed in neat cement slurry and pointed in grey cement with pigment to match the shade of tile,complete all as specified and directed by Engr in Charge.

Supply and fixing factory made steel windows (Box type) with glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc including one shop coat of red oxide zinc chrome primer, fixed as in repairs, complete all as specified & shown in drawings, complete all as specified & directed by Engr in Charge.

Supply and fixing factory made steel windows (Box type) without glazing bars, dovetailed or welded including hinges, steel handles, steel peg stays etc including one shop coat of red oxide zinc chrome primer, fixed as in repairs, complete all as specified & shown in drawings, complete all as specified & directed by Engr in Charge.

M&L for 4 mm thick tinted sheet glass ordinary quality secured with glazing pin or nails etc and glazing with oil putty or wooden beads in squares exceeding 0.50 Sqm in each pane,complete all as specified and directed by Engr in Charge.

M&L for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long , fixed in repair, complete all as specified and directed by Engr in Charge.

M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engr in Charge.

M&L for framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or FE 310-0 all complete all as specified and directed by Engr in Charge.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by Engr in Charge.

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring, joints, fixed to walls in repairs 110mm bore complete all as specified and directed by Engr in Charge.

S&F in repair PVC (SWR) bends in any radius 110mm bore in repairs complete all as specified and directed by Engr in Charge.

S&F stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and screwing ends of stay to wall or roof of 100mm bore pipe complete all as specified and directed by Engr in Charge.

M&L for demolition of brick work or stone masonary built in cement mortar or cement lime mortar complete all as specified and directed by Engr in Charge.

M&L for brickwork with subclass B bricks, straight or curved on plan exc 6m mean radius, built in (1:6) complete all as specified and directed by Engr in Charge.

M&L for brick work with sub class 'B' bricks, using old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, complete all as specified .

M&L for reinforced cement Concrete design mix type B1 1:2:4(20 mm graded aggregate) as in slabs supported on walls, beams and columns in floors,roofs, landings balconies ,canopies, deck slabs and in shelves complete all as specified and directed by Engr in Charge.

M&L for reinforced cement Concrete design mix type B1 1:2:4(20 mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed by Engr in Charge.

M&L for use and waste of form work to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, n.exc 200 mm thick ( horizontal or sloping) , for rough finished flat surfaces, complete complete all as specified and directed by Engr in Charge.

M&L for use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exceeding 20 cm wide, etc. to obtain rough flat finished surface of concrete complete all as specified and directed by Engr in Charge.

M&L for use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions etc, square, ractangular or polygonal, to obtain rough finished flat surface of concrete complete all as specified and directed by Engr in Charge.

M&L for dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engr in Charge.

M&L for dismantling plain or corrugated steel sheeting/ asbestos cement any gauge thickness including nainital or similar pattern roof coverings complete all as specified and directed by Engr in Charge.

M&L for pre-laminated galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for pre-laminated galvatume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr in Charge.

M&L for galvanized mild steel wire cloth 0.56mm normal dia of wire and average width of apparatus 1.18mm and fixed width tinned lacks of galvanized wire staple complete all as specified and directed by Engr in Charge.

M&L for 18/19mm thick prelaminated particle board medium density flat pressed single layer type or three layer type with BWR type adhesive.complete all as specified & directed by Engr in Charge.

M&L for flush shutters, 25 mm thick ,solid core construction, with block board core and plywood face panels, commercial type on both sides, including beading complete all as specified and directed by Engr in Charge.

M&L for flush shutters, 25 mm thick ,solid core construction, with block board core and plywood face panels, commercial type on both sides, including beading complete all as specified and directed by Engr in Charge.

S&F powder coated anodised aluminium frame for doors/windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed by Engr in Charge. .

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete complete all as specified and directed by Engr in Charge.

M&L for mortice lock, vertical type, size 100 mm 4 lever complete all as specified and directed by Engr in Charge.

M&L for chipping /removing loose concrete up to reinforcement bars, without damaging the reinforcement, removing all the loose materials and to make all the exposed surfaces free from oil, dust and all impurities etc., complete all as specified and directed by Engr in Charge.

M&L for removing all loose scale and corrosion deposits of the exposed corroded steel incl surface preparation corroded steel should be cleaned all around incl the back of exposed reinforcement with the clearance/ gap between steel & concrete as recommended by manufacturer, then applying rust remover with brush by complete wetting the rusted material surface by rust remover & leaving for 24 hrs and thereafter surface preparation of coated bars and applying 2nd coat of rust remover & leaving the same for the specific period as per manufacturers instructions and further again preparing and cleaning the steel surfaces for treatment complete all as spd & dir by the Engr in Charge. .

M&L for providing and fixing rebar of required length and diameter with sika anchor fix @ 3+ fosroc lock fix/equivalent in BASF wherever required in RCC members including power drilling, cleaning of holes then rebar should be inserted in the holes, that should the filed with epoxy as mentioned above to ensure the bond as per manufacturers instructions complete for the following diameter of bars as per site and complete all as specified and directed by Engr in Chargerequirement & as directed by Engr in Charge. (a) 8mm/10mm/12mm/TMT bars

(b) 16 mm /20mm/TMT bars

Corrosion Resistance Coating: M&L for applying passivator/ anti corrosion coating to the prepared reinforcement steel surfaces of items No-73 above. The material shall be cement based polymer modified coating for corrosion protection and shall be applied as per manufacturers instructions and complete all as specified and directed by Engr in Charge Make:- Sika Armatec 108/ Fosroc Nito cole AP-35/ Equivalent in BASF Note:- Site for application is at various locations and height varies up to 15.0M Proper stable Scaffolding is must for working

M&L for preparation of old RCC/ concrete surface and applying a coat of (two components solvent free) epoxy bonding agent using brush after cleaning of surface from all dust or laitance all as per manufacturers instructions and complete all as specified and directed by Engr in Charge Make:- Sika Sikadur 32 LP/ Fosroc Nitobond EP/ Equivalent in BASF Note:- Site for application is at various locations and height varies up to 15.0M Proper stable Scaffolding is must for working

M&L for providing and applying ready to use single component high strength polymer modified cementious repair mortar 25 mm thk with water/ powder ratio as specifiedby manufacturer so as to achieve the following parameters:- (i) 28 days Compressive Strength>= 50N/mm2 (ii) Flexural Strength at 28 days>= 5 N/mm2 Make:- Sikatop 122 HS/ Fosroc Nito Mortars/ Equivalent in BASF Note:- Site for application is at various locations and height varies up to 15.0M Proper stable Scaffolding is must for working

Curing Compound :- M&L for applying high efficiency water based film forming curing compound over the fresh concrete cementious surface to form a continuous non-penetraling coating providing a barrier to moisture loss ensuring more effcient cement trydration improved durability and reduced shrinkage. The compound shall be applied by sprayer only as per manufactuere instuctions to ensure complete and proper coverage, Pump pressure should be maintained to give an even fine spray and finish as per the manufacturer specification.

M&L for making V groove of 10mm wide and 30mm deep or upto the extent of crack present at site over crack line using electricity operated angle grinder with diamond concrete waw blade and cleaning it by air blower. The groove shall be cut on the concrete surface along the crack over beam. or column to be repaired. There after sealing of exposed V groove with solvent free, moisture tolearnt, thixotropic two part structrual adhessive and epoxy repair mortar cum surface leveing mortar as per manufactures instructions and as directed by Engr in Charge.

M&L for providing Micro concrete jacketing upto 75mm to columns using polymer modified cement premixed quartz sand aggregate packed in bags of standard manufacture, for high early strength of 40 N/mm sqcm of approved brand. The dry product is to be mixed with 12.5 % water by weight, along withwashed and poured into rigid formwork moulds & tamped properly, and cured for 3 days incl formwork complete all as specified and directed by Engr in Charge

M&L for pressure grouting in the honey combed concrete for providing and fixing grouting nozzles and injecting high strength epoxy resin injection through the nozzles under pressure using grout pupm to fill al possible pores and gaps left within the concrete mass, all as per directions of Engr in Charge. .The process shall consist of:- (i) Drilling Holes: Drilling holes in structural members at the intervals as per recommendation of Engr in Charge. . (ii) Cleaning of Holes: Clean the holes by air blower prior to fixing nozzles (iii) Fixing of Nozzels: Insert 12 mm dia, 50-75 mm long injection packers in cleaned holes with structural grade epoxy adhesive. (iv) Supply and apply a shrinkage free low viscous epoxy resin based injection grout. (v) Cutting of Packers: Cut the packers by cut of wheel after completion of grouting without damaging structural elements. Make: Sika Sikadur 52/ Fosroc CONBEXTRA- EP10 or equivalent of BASF

Shear Connectors: M&L for making 10/12 mm dia holes using heavy duty electrically operated hammer drills in the concrete of RCC members to a depth of about 75 mm at 500 mm c/c or at suitable grid in zig-zag fashion, clean the holes using air jet and fix pre-fabricated 100 x 50 mm L-shape 8 mm dia rebar using Anti Corrosive protective coating so that 75 mm out of 100 mm is inserted inside the concrete and 25 mm remain outside along with 50 mm bend. The shear connectors are used to tie the additional reinforcement bars. FOSROCK - HILTI, Ficher Note:- For items 73 to 82 (i) Work shall be executed only through authorised applicators of the Manufacturer. (ii) Site for application is at various locations and height varies up to 15.0M (iii) All Scaffolding work and safety measures such as provision of props and supports shall be of steel and extent of provision shall be entire satisfaction of GE. (iv) Mode of measurement for items: For the purpose of the measurement of these items the surface area of the patch of the concrete considered of repair shall be taken.The T&P shall be strictly as per manufacturers instructions. (v) Testing of cube strength of polymer modified cementious mortar shall be independantly carried out as per manufacturers instructions and record shall be maintained. (vi) After obtaining approval of the make of the products the contractor shall give a letter from the manufacturer regarding the details of the agency and the name of person to be deployed for carrying out repair & Supervision of the work. (vii) Contractor shall submit gurantee in shape of FDR/ BGB for Rs 50000(Fifty thousand) for ten years in there letter pad (for SI no 73 to 82 )

M&L for demolition of reinforced cement conc of any description and in any position complete all as specified and directed by Engr in Charge

M&L for separating scraping and cleaning of reinforcement obtained from demolition complete all as specified and directed by Engr in Charge

M&L for mild steel (TMT) bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr in Charge

All as per item 85 above but 5mm dia & over upto & lincl 10mm dia in striupps, spacers & binders complete all as specified and directed by Engr in Charge

M & L for RCC M 25 design mix using 20mm graded aggregate as in fins, facias, roof parapets complete all as specified and directed by Engr in Charge.

M&L for formwork to faces of ,parapets and staircase railingsand similar work including attached pillasters, buttresses,etc.; vertical or to batter roof parapets complete all as specified and directed by Engr in Charge.

M&L for 20mm bore ball valve, brass, high pressure with polythene float and fly nut complete, screwed for iron pipe, fixed in repair,complete all as specified and directed by Engr in Charge.

M&L for stop valves, fancy type chromium plated cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore 15mm, fixed in repairs complete all as specified and directed by Engr in Charge.

M&L for taking up or down steel tubing with connections for cleaning for refixing or removing from site of bore 15mm , complete all as specified and directed by Engr in Charge.

M&L for taking up or down steel tubing with connections for cleaning for refixing or removing from site of bore 20mm , complete all as specified and directed by Engr in Charge.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm, complete all as specified and as directed.

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings( such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 20 mm, complete all as specified and directed by Engr in Charge.

M&L for rotational moulded polyethylene water storage tanks three layer white in colour , ( cylindrical vertical with closed top white in colour), hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres including all fitting accessories, complete all as specified and directed by Engr in Charge.

M&L for PVC connections 15 mm size with brass nuts of length 600 mm, fixed in repair, complete all as specified and directed by Engr in Charge.

M&L for cement concrete 1:3:6 type C2 ( Using 40 mm graded crushed stone aggregate ) as in surface channel or drain etc,complete all as specified and directed by Engr in Charge.

M&L for cement concrete 1:2:4 type B-1 ( Using 20 mm graded crushed stone aggregate ) as in lintles upto 1.5 mtr clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapet up to 60 cm height, copings, kneelers, appex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles, throating and necessary form work etc,complete all as specified and directed by Engr in Charge.

M&L for stainless steel sink, (with drainage board) 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, fixed in repairs,complete all as specified and directed by Engr in Charge.

M&L for aluminium window air tight of anodised frame made of size 100 mm x 45mm of section thickness -1.50 mm thick and shutter stiles made of section 80mm x 45mm x1.5mm thick with or without rebates, with 5.5 mm thick tinted glass fixed with aluminium beads , including necessary jointing cleats /anodised aluminium fillets/aluminium glazing clips with rubber gasket ,with aluminium fittings such as aluminium butt hinges 100mm long 02 Nos , aluminium anodised tower bolt 100mm long 02 No , aluminium anodised bow handles 100 mm 01 no , aluminium hook and eye 150mm -01 No in each shutter, including ornamental aluminium grill of appropriate section,complete all as specified and directed by Engr in Charge. Note : All fitting shall be of ISI marked except cleats ) sizes of each window shall be as per site requirement all as directed and specified .

M&L for anodised aluminium door air tight of anodised frame made of size 100 mm x 45mm of section thickness -1.50 mm thick with one or more rebates including jointing cleats etc for fixing aluminium anodised door shutter fully panelled (two no of panels on each shutter) with 5.5 mm thick tinted glass as in panels, shutter rail made of 80mm x45 mm of sheet thickness 1.50 mm ( Top rails and stiles) middle and bottom rail of size 150 mm x 45 mm, single /double leaf side hung type including necessary jointing cleats /anodised aluminium fillets/ glazing clips with rubber gasket ,with aluminium fittings such as aluminium anodised tower bolt 200mm long 03 No for each door, aluminium anodised bow handles 150 mm 'D' type 02 nos for each shutter , mortice locks 6 lever make - harrison one on each door, door shutter mounted on bottom double action floor spring hydrailically regulated made up of 1.25mm thick aluminium alloy sheet foundation box , main body with stainless steel cover , governing pivot made of brass, other parts made of mild steel heavy duty and door shutter top mounted on. -01 No on each shutter , bottom and floor stoppers, complete all as specified and directed by Engr in Charge. Note : All fitting shall be of ISI marked except cleats ) sizes of each door shall be as per site requirement all as directed and specified .

M&L for harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and directed by Engr in Charge.

M&L for gypsum board multi level false ceiling 12mm thick of any shape and design fixed with standard GI frame work with GI furring channels of 16 gauge, main 'U' shaped channels @ 1220mm C/c and inter connected cross channels "C" shape spaced at 610mm c/c, Main and inter connected channels ahsll be fixed through fasteners clipe as per manufacturer's instructions, with and including plaster of paris decorative type cornices all around at he juction of wall and ceiling etc all as specified in TD-637 and soffits of false ceiling boards shall be applied with two coats of plastic emulsion paint over a coat of primer including dismantling removing serviceable board to store and rubbish off the premises, all as specified and directed by Engr-in Charge.

M&L for taking down carefully point wiring copper/ aluminium (light, fan, socket and power) complete (fittings such as switches ceiling roses, pendent regulators sockets etc to be measured and paid for seperately removing materials to store for keeping of safe custody and making good the distrubed surfaces complete all as specified and directed by Engr in Charge.

M&L for point wiring with PVC insulated unsheathered, FRLS 1100 volts grade stranded copper conductor cable single core 1.5sqmm for one light/ fan point/ bell point controlled by one way switch, and wire to be drawn in and including concealed conduit of dia not less tham 25mm complete with all accessories including MS sheet metal 1.2mm thick switch board of suitable size to be fixed flush wall, with 3mm thick ebonite sheet cover and necessary screws, cap washers etc, or to be fixed on wall respectively as directed by EIC and providing earth continuity wire using PVC insulated, unsheathered single core stranded copper conductor FRLS cable of size 1.5sqmm complete all as specified and directed by Engr in Charge.

All as per item No. 105 above but for one 3/5 pin socket 5Amp on same board with cable 1.5sqmm size.

All as per item No. 105 above but for one ./5 pin socket 5 Amp on independent board with cable 1.5sqmm size.

All as per item No. 105 above but for 3 pins socket outlet 15 Amps independent with 2.5sqmm incl continous earthing with multistranded copper conductor PVC insulated unsheathered size 2.5 sqmm complete complete all as specified and directed by Engr in Charge.

S&F switch piano flush type single pole 5 Amps one way, complete all as specified and directed by Engr in Charge.

S&F socket flush type single pole 5Amps one way, complete all as specified and directed by Engr in Charge.

S&F switch socket combination 2 in 1, 3pin, 5 and 15 Amp flush type universal complete all as specified and directed by Engr in Charge.

S&F stepped type electronic fan regulator flush type on the existing phenlic laminated sheet etc complete all as specified and directed by Engr in Charge.

S&F ceiling rose, 3 terminal, PVC/ polycarbonet, isolated body complete complete all as specified and directed by Engr in Charge.

S&F slim linear LED lighting fixture 20watt LED batten, with full base of extruded aluminium sectio acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5sqmm copper conductor multistranded PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old US tube fitting 1x36W and taken in schedule of credit all as per the directed.

S&F LED light fitting PLUTO NEO PANEL 2'x2' PLR 36 wat LED 857S environmental friendly, new generation aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source suitable for armstrong/ grid/ ceiling complete all as specified and directed by Engr in Charge.

S&F LED street light fitting 35 watt 230V AC outdoor type with high pressure dia cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and connection resistant thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed by Engr in Charge.

M&L for taking down fan, ceiling cable and kept in safe custody for refixing on same location complete all as specified and directed by Engr in Charge.

M&L for repair of ceiling fan/ exhaust fan 1200/300mm sweep of any make obtained from above item, oiling greasing cleaning slot, over hauling and replacement of defective nut bolts washer etc including painting, if as per site requirement fan will be found burnt rewinding will be provide by the contractor as per unit quoted rate complete all as specified and directed by Engr in Charge.

M&L for hanging/ fixing only ceiling fan/ exhaust fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from site complete all as specified and directed by Engr in Charge.

M&L for submain wiring with 2x6.0 SQMM+1X6.0 SQMM Earth wire single core PVC insulated FRLS sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC concealed conduit as per site requirement including taking down old us submain wiring and direction by EIC, all accessories complete complete all as specified and directed by Engr in Charge.

S&F single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar, neutral link, earth bar and din rail suitable for use on 240V , 50 Hz supply double door SP&N DB system 12 ways complete all as specified and directed by Engr in Charge.

S&F 'C' series SPN MCB 40 to 63 Amps 240V, 50Hz, 10kA lighting and other domestic loads incl all terminals, fittings etc. complete all as specified and directed by Engr in Charge.

S&F 'C' series SPN MCB 06 to 32 Amps 240V, 50Hz, 10kA suitable for lighting and other domestic loads incl all terminals, fittings etc. complete all as specified and directed by Engr in Charge.

M&L for earthing complete with galvanixed steel earth plate electrode 60x60cmx6mm thick, buried directly in ground (earth pit not less than 2.25meters deep below ground level) with top edge of the plate not less than 1.5metres below normal ground level, connected to galvanised earth lead wire 4.0 dia by means of bolts, nuts, check nuts and washers of galvansied iron or steel all as shown in electrical plate No.5 of MES Part1 fixed in replacement including testing on completion including the material and labour of the following:- (a) Exacavtion and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighting not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply and lay XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (hyeavy duty) 1100volts grade with stranded aluminium conductor of size 16 sqmm 4 core in trenches/ floor/ pole/ GI pipe complete including cutting/ chasing to any surface and making good to the distrubed surface to match the existing complete all as specified and directed by Engr in Charge.

M&L for GI tubing light grade with all fittings and fixed in wall and floor or fixed to pole of size 40mm dia complete all as specified and directed by Engr in Charge.

VARDHMAN INTERNATIONAL

SHIVAE CONSTRUCTION