WBPWD/EE /AED /short bid e-NIQ-20/2021-22

Amount

Supply of 4/3.5 Core XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make Nicco /Gloster/ Havells/ R R Kabel] (a) 4Core240 Sq. mm

(b) 2 Core 10 Sqmm

Laying of two cables above 185 sqmm in an underground trench in single tier formation (horizontal), the trench size : 680 mm x760 mm average depth, with brick protection on the top of each cable 8 (eight) Nos. bricks per Mtr. and 4 (four) Nos. bricks per Mtr. as separator between the bricks and cables and also trench to be filled up with shifted soil, levelling up and restoring surface duly rammed

Laying of one No. cable upto 35 sqmm in underground trench as per GS.

Laying of cable as below, on existing Cable Tray and binding with suitable size GI wire as per GSabove (a) 150sqmm

Laying of one cable above 150 sqmm and upto 300 sqmm through existing covered masonry trench incl. taking out RC covers, setting them in order, mending good the damages filling the trench with fine dry sand without supplying sand

Supplying and fixing compression type gland and finishing those for following XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS. (a) 4Core 240 Sq. mm

(b) 2 Core 10 Sqmm

M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, flat,channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design,

Supply & Fixing of perforated GI cable tray ( 18SWG) with perforation not more than 17.5% suspended from ceiling incl. S&F GI connector, 6mm dia MS suspender with / without angle iron support as per GS With 25x25x3mm angle iron support (a) 200x50x1.25mm

Supply & Fixing of perforated GI cable tray Bend as per GS. (a) 200x50x1.25mm

Supply & Fixing of perforated GI cable tray Tee as per GS. (a) 200x50x1.25mm

Supply & Fixing of perforated GI cable tray Cross as per GS. (a) 200x50x1.25mm

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings as per GS (a) 80mm dia

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level

Excavation of soil for installation of Earth Electrode and filling & ramming.for soft soil

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe

Extra for treatment of soil by using salt & charcoal or coke for plate electrode

Providing CC (6:3:1) muffing 600x600x760 mm in size or equivalent size of cylindrical muffing above ground level around the pole base complete with 3 mm thick neatly finished cement plaster and nutbolt arrangement all round after dismantling the unserviceable muffing if necessary without loop box

Supplying and Fixing stainless steel (4mm thick) water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged looping cable box etc. where necy. incl. painting 200 x 150 x 100mm

S&F of floor cum wall mounting main cubicle compartmentalised 415V,50Hz Dust & moisture proof LT distribution panel board fabricated from 16SWG CRCA sheet for main LT panel.the panel should haveadequate strength and space to accommodate the incoming switches busbars with all interconnection in between the switches &busbars with solid copper rod/flexible wire with suitable capacity as per direction of EIC. the panel board should be painted by powder coated paint and the panel should be comprise with the following gadgets.a) Incomer: 415V,630A Main Switch with 3nos. HRC fuse(L&T/Seimens ) b) 550V ,800A BBC,with 4nos. copper bar on non hygroscopic chair -1set C) S&F digital 0-500V voltmeter(L&T/Seimens/schnieder)-1 d) S&F digital 0-100A Ammeter(L&T/Seimens//schnieder) with CTR 100/5A-1set e) S&F LED pilot lamp(RYB)-3nos outgoing: f) S&F 415V ,400A FP MCCB(L&T/Seimens )-2 nos.g) S&F 415V ,125A FP MCCB(L&T/Seimens )-2nos.h)S&F 415V ,63A FP MCCB(L&T/Seimens )-1no. incl.2.5 ft RCC platfrom & painting as per direction of EIC.

S&F of floor cum wall mounting main cubicle compartmentalised 415V,50Hz Dust & moisture proof LT distribution panel board fabricated from 16SWG CRCA sheet for main LT panel.the panel should haveadequate strength and space to accommodate the incoming switches busbars with all interconnection in between the switches &busbars with solid copper rod/flexible wire with suitable capacity as per direction of EIC. the panel board should be painted by powder coated paint and the panel should be comprise with the following gadgets.a) Incomer: 415V,400A Main Switch with 3nos. HRC fuse(L&T/Seimens ) b) 550V 600A BBC,with 4nos. copper bar on non hygroscopic chair -1set C) S&F digital 0-500V voltmeter(L&T/Seimens/schnieder)-1 d) S&F digital 0-100A Ammeter(L&T/Seimens//schnieder) with CTR 100/5A-1set e) S&F LED pilot lamp(RYB)-3nos outgoing: f) S&F 415V ,250A FP MCCB(L&T/Seimens/Legrand )-2 nos.g) S&F 415V ,125A FP MCCB(L&T/Seimens/Legrand )-2nos.h) S&F 415V ,63A FP MCCB(L&T/Seimens/Legrand )-2nos. incl.2.5 ft RCC platfrom & painting as per direction of EIC.

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3 mm thick and incl.175x100x65mm inspection box, making earthing attachment,painting the MS box and mending good the damages to original finish [only PVC Rigid Conduit on ceiling and remaining portion concealed]Avg Run-12mtr

b)on board

Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire of the through 19mm/25mm polythene pipe as per GS. a)3 x (1.5 sqmm)

b)2x(2.5 sqmm)+1x(1.5 sqmm)

c)2x (6 sqmm) + 1x (4 sqmm)

d)4x10sqmm+2x6sqmm

S&F of required size solderless Cu socket of following Cu wires. a) 2.5sqmm

b) 6sq mm

c) 4sq mm

d) 10sq mm

Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall as per GS. (a) 2+10 Way[ Legrand ]

Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection as perGS [Make-Legrand ] 40 A DP

Supplying and fixing 6-32 SP,240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connectionas per GS [ Make -Legrand ]

Supply and fixing double door 4way TPNDB MCB DB with IP42/43 protection concealed in wall as per GS(Legrand)

Supply and fixing 415V 63A FP Isolator on din rail of existing DB as per GS(make-Legrand)

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required

Supply of 4 Ft. single/twin LED light fitting for indoor application,complete with all accessories & Lamps having following Model / Cat No.( Make -Crompton/magik/Bajaj) a. 1xT-LED 22W P3241 with PC body

b. 2xT-LED 22W P3242 with PC body

S & F9W LED (Crompton/magik/Bajaj)) at existing batten point at toilet

Supply and fixing 50W LED flood light( make-Crompton/magic )

S&F LED 120W ,5000K Flood light on the existing pole( Make-crompton/havells/Panasonic)

S&F LED 120W ,5000K Street light on the existing pole( Make-crompton/havells/Panasonic)

S&F fabricated Angle iron (35mmx35mmx6mm) 2ft length for fixing of LED flood light with drilling/welding on metal board

S&F fabricated Angle iron (35mmx35mmx6mm) in round shape and necessary nut bolts for fixing of LED flood light with drilling/welding on metal board

Fixing only single/twin fluorescent/LED light fitting in the ceiling fixed with “L” type MS clamp as per GS

Extra for suspension exceeding 25 cm with S&F additional 2 no. 20 mm dia EI conduit as per GS

Supply of ceiling fans complete with all accessories having the following Model / Cat No. ( Make -Crompton Greaves/Usha ) (a). 1200 mm Sweep

Supply of wall fans 230v 450 mm complete metal wall fan with all accessories . Make USHA /ORIANT /CROMPTON /EPC ) as per diraction of EAC

Supply of Exhaust fans complete with all accessories having the following Model / Cat No. ( Make -EPC ) a) 9" Speed 920 RPM

b) 12" Speed 920 RPM

c) 18" Speed 950 RPM

Supply & Fixing Socket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switch board with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connections etc.

Fixing only wall fan as per GS.

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc as per GS.

Fixing only exhaust fan on after making holes in wall as per GS a) (9")

Supply & Fixing louver shutter ( Aluminum)on wall with necy. bolts & nuts (6 mm dia x 62 mm long) with net protection as per GS a)(9")

JAYBEECO

ROYAL ENGINEERS CO-OPERATIVE SOCIETY LTD