GE/863/EWS-T-51 OF 2020-21

Amount

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling mild steel work of any description not otherwise provided for complete all as specified and directed.

Taking down cement plastering at any description on brick or stone wall etc including raking out joints hacking for key scrubbing down with water etc and removal of debris and depositing where directed complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 2 Sqm each complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors / dado etc laid bedded and pointed in any mortar complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep for foundation,etc and getting out in hard/dense soil complete all as specified and directed.

M&L for P.C.C 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed

M&L for walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM 1:6 complete all as specified and as directed

M&L for walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted built in CM 1:6 BUT EXCEPT STONE complete all as specified and as directed

M&L for Extra over stone walling up to 40mm for hammer dressing to face stone and dressing of face , bed and joint as specified for random rubble walling uncoursed complete all as specified and directed.

M&L precast PCC 1:3:6 type C1 using 20mm graded stone aggregates as in bonder stones set in cement mortar 1:6 complete all as specified and as directed.

M & L for block masonry with solid pre-cast cement concrete blocks made out of cement concrete 1: 3: 6 type C-1, using 20 mm graded stone aggregate, exc. 10 cm in width and setting in cement mortar 1 : 6 complete all as specified and directed.

Returning, filling in, including spreading, leveling , watering, and well ramming in layers n.exc 25 cm thick complete all as specified and as directed.

M&L for spreading and leveling n.exc 25cm thick incl well ramming incl watering complete all as specified and directed.

M & L for 40 mm thick Cement Concrete M-15 Nominal Mix (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - water proofing compound will be measured and paid separately.

Supply only water proofing compound (WPC) complete all as specified and directed.

Removing excavated material (Soil) to a distance n. exc 50m and depositing where directed at a level n. exc. 1.5m above the starting point complete all as specified and as directed.

M&L for Hard core of gauge n exc 63mm thick of broken boulder spread leveling watering ramming to true surface complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B1, 20 mm graded stone aggregate as in flooring including finishing cement concrete rough surface with out using extra cement complete all as specified and directed.

M &L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) as in sub base in floors complete all as specified and directed.

M&L for 75 mm thick P.C.C 1:4:8 type B-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and as directed

M&L 75mm thick cement concrete 1:3:6 type C2 with using 40mm graded stone aggregate as in plinth protection surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded granite stone aggregate) in sub base of flooring/ hard standing /footpath complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 15mm thick screed bed or bedding in CM 1:6 complete all as specified and as directed cement to match complete all as specified and as directed

M&L for 300x200x7 mm thick glazed coloured ceramic tiles as in dado over and including 10mm thick back coat in CM 1:4 etc. set and jointed in neat cement slurry and pointed in coloured cement with pigment complete all as specified and directed.

S&F chequered cement concrete tiles 30cmx30cmx22 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry as in floors including over and including screed bed or bedding layer of 15mm thick in CM 1:4 for laying floor finishes with 75 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base etc complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20 - 25 mm thick over and including 20 mm thick screed bed laid in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 as in on stone masonry surfaces finishing even and smooth without using extra cement complete all as specified and as directed.

M&L rendering 15 mm thick in CM 1:6 on concrete solid block wall surface finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15 mm thick on fair faces of stone walling in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10mm thick cement plaster in CM 1:3 on fair faces of brick work or concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L Providing, cement concrete Type B1 1:2:4 (20 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L Reinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Form work rough finished surfaces of concrete to sides and soffits of beams , lintel and similar items complete all as specified and directed.

S&F Mild TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde - E-165) complete all as specified and directed.

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases od columns , raft and raft beams , sides and soffits of foundation and plinth beams and similar work vertical or better for rough finished surfaces of concrete complete all as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs , floor slabs , landing etc not exc 200 mm thick (horizontal or slopping ) for rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M30 Grade (using 20mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete (design mix) M30 Grade (using 20mm graded stone aggregate) in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L Reinforced Cement Concrete (design mix) M30 (using 20 mm graded granite stone aggregate) for slabs suspended on walls, beams and columns, in floors, roofs, landings and in shelves and the like complete all as specified and directed.

M&L for precast cover slab (for manholes etc), shelves and similar work set in cement mortar 1:4 type B1 1:2:4 using 20mm graded stone aggregate complete all as specified and directed.

S&F PVC waterbar 200mm x 8mm thick complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

S&F 0.63 mm thick galvanized corrugated mild steel sheeting with two corrugation side lap fixed with coach screws and washers, in roof walls etc with grade of zinc coating 275 complete all as specified and directed.

S&F 0.63 mm thick galvanized corrugated mild steel sheeting with two corrugation side lap fixed with coach screws and washers, in roof walls etc with grade of zinc coating 275 BUT EXCEPT SHEET complete all as specified and directed.

S&F rolled mild steel Framed work such as in grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; ramed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F Solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for tip rail & bottom rails; Paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement. supplying and fixing in the frame at site complete all as specified and directed.

S & F 150 mm long Aluminium, anodized, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm long Aluminium, anodized, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm long heavy weight, cold rolled mild steel Butt hinges complete all as specified and directed.

S & F 100 mm long extruded Aluminium alloy anodized Butt hinges with galvanized mild steel hinge pin type C 21 complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodized complete all as specified and directed.

S & F 125 mm long Extruded Aluminium alloy handles, fabricated type, anodized complete all as specified and directed.

S & F of aluminium alloy, anodized, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L Preparation of New or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer complete all as specified and directed.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for one coats synthetic enameled paint incl preparation of old steel surfaces of any description over 10cm width or girth complete all as specified and as directed

Material & Labour for two coat of cement base paint on new plastered surface including preparation of surface complete all as specified and directed.

M&L preparation of old surface of wall plastered including cornices and pillasters etc and applying one coat of cement base paint on wall complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L preparation of old surface of wall plastered including cornices and pillasters etc and applying one coat of white wash on wall complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3mm Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F fixing Vitreous China wash hand basin white flat size 550x400mm incl bracket cutting for and pining in ends of brackets or erecting stand but exclusive of fixing of Waste pipe complete all as specified and directed.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F 15mm bore CP stop valves fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipes or unions and fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 15 mm GI tubing medium grade with all fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) of 1000 Ltrs capacity hoisted and fixed in position incl 20mm bore PVC float valve complete all as specified and directed.

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching as required, 100mm dia pipe complete all as specified and directed.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down unserviceable main switches, DBs / changeover switch alongwith Teak wood boards etc and making good the disturbed surfaces of wall / floors to match the existing surface complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm FRLS PVC insulated stranded copper conductor cable for continous earthing in & including PVC casing & caping with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. for One light point / Fan/ bell point controlled by one switch complete all as specified and directed.

One light point / Fan/ bell point controlled by one switch

One socket 3 Pin 5A pin socket oulet 5Amps on same board with cables 1.5 Sqmm size

One socket 3 Pin 5A pin socket oulet 5Amps on indepndent board with cables 1.5 Sqmm size

One socket 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size

S&F switch piano flush type single pole one way 5/6 Amps complete all as specified and directed.

S&F lamp holder Angle / batton type insulated body with back plate and to be fixed on PVC bock complete all as specified and directed.

S&F socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one complete all as specified and directed.

S&F switch piano15 Amp 230 Volt, flush button single pole one way complete including dismantling old one complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type complete including dismantling old one complete all as specified and directed.

S&F ceiling rose surface tpe 3 terminals to be fixed on PVC block complete including dismantling old one complete all as specified and directed.

S&F LED integrated batten tube light fittings 20W 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed. Make : Cat Part No : LTTB4F20WLED/W of C&S or equivalent as approved.

M&L DB SPN sheet metal enclosure single door suitable for mounting MCB 240 Volts with busbar 8 way complete including dismantling old one complete all as specified and directed.

S&F MCB SPN 230 Volts 40 Amps complete all as specified and directed.

S&F MCB SP 230 Volts 6- 32 Amps complete all as specified and directed.

S&F LED lamp 9W system lumen (NOM) 600 with all accessories complete all as specified and directed. Make: Cat part No :- LTHPLEDLAMP9WB22 of C & S or equivalent as approved

S&F recessed mounted LED luminaire 36 W system lumen (NOM) 4000K with all accessoriescomplete all as specified and directed. Make: Cat part No:-LTCRP36WLED2X2 of C & S or equivalent as approved.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6.3 mm thick, buried directly in ground (eath pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised iron wire 4.0 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR-2009 (Part-I) connected to earthing test point including funnel with wire mesh, PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) chamber, PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) cover 80 mm thick , GI watering pipe 20 mm dia, medium grade, 15 mm dia GI protection pipe,light grade and adequate quantity of salt and charcoal, with necessary excavation, earth work and formwork and testing on completion, complete all as specified and directed. Note: GI earth wire upto 7.5 Mtr is deemed to be included in the quoted rate.

S&F 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart incl 4 mm suspension wire, one twin core cable flat of size 10 Sqmm complete all as specified and directed.

S&F Energy saving new generation 10W LED 6000K IP65 bulkhead luminaire with opal diffuser complete all as specified and directed.

M&L for House service bracket (hook type) complete with 3.0 mtr long G.I pipe 40mm dia Med grade, two nos 90 degree bends, MS hook and stay or guy complete all as specified and directed.

M&L DB SPN sheet metal enclosure single door suitable for mounting MCB 240 Volts with busbar 4 way complete complete all as specified and directed.

Net Contract Sum will be after deducting Sch Of Credit of Rs. 15876.00

PRITPAL SINGH