REPAIR TO AREA DRAINAGE AND REPAIR TO COMPOUND WALLS, FENCING AT NAS SHIBPUR

Amount

Demolition of brickwork or stone/ boulder masonry or PCC block masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removal of debris to a distance exceeding 500 mts and depositing where directed.

Taking down cement plaster on brick or stone walls, concrete surfaces etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L Pre-cast cement concrete Type C1, 1:3:6 (using 20mm graded crushed granite stone aggregate), block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete.

M&L for rendering 15mm thick on fair faces of brick/ concrete surfaces in two layers of 10 mm thick plastering in CM 1:4 and followed by 5 mm thick plastering in CM 1:4 complete.

Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L PCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in copings, kneelers, apex stones, bed plates, levelling course, kerbs water troughs and the like including use of formwork, weathering, slightly rounded or chamfered angles and throating, finished even and smooth without using extra cement all as specified.

M&L for PCC Type B2, 1:2:4 (using 40 mm graded granite stone aggregate) as in surface channels and drains complete.

M&L for PCC Type D2, 1:4:8 (using 40 mm graded granite stone aggregate) as in foundations, filling and mass concrete.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for and removal of debris to a distance exceeding 500 mtrs and depositing where directed.

M&L precast RCC Type B1, 1:2:4 (using 20 mm graded granite stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces and set in CM 1:6, including necessary formwork complete. Note: Reinforcement shall be measured and paid separately.

M&L for high yield strength deformed TMT steel bars 10 mm dia and over as in reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for providing steel formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat fair finished surfaces of concrete all as specified.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. (Inner girth only shall be measured).

Desilting of storm water drains including dewatering and removing soil/ muck to outside the MD land and depositing where directed.

Excavating in trenches, not exceeding 1.50 mtr wide and not exceeding 1.50 mtr in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 sqm on plan and getting out in any type of soil (soft/ loose or hard/ dense).

Removing excavated material not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil.

M&L for providing steel formwork to sides of pillars, posts, struts, piers, columns and stanchions for square, rectangular or polygonal fair finished surfaces of concrete all as specified.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as columns, pillars, piers, posts and struts.

M&L for providing steel formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter, for flat rough finished surfaces of concrete all as specified.

M&L for RCC M-30 design mix (using 20mm graded granite stone aggregate) as walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses.

M&L for high yield strength deformed TMT steel bars 5 mm dia and over up to 10 mm dia as in stirrups, spacers and binders reinforcement for concrete, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Excavating in post holes (or similar holes) each not exceeding 0.5 cu. m, getting out in any type of soil (i.e. soft/loose soil or hard/dense soil), returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance not exceeding 50 m and making good surface.

M&L for PCC Type C1, 1:3:6 (using 20 mm graded granite stone aggregate) as in foundations, filling and mass concrete.

S&F mild steel angle iron and flats including embeding in concrete and screwing etc. including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F 1 mm thick PVC coated chain link fencing wire mesh of size 150 mm x 100 mm, made of 4 mm dia MS galvanised wire, to any type of standards, rails, straining bolts, etc including provision of GI wire binding complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Providing precast cement concrete Type B0, 1:2:4 (using 12.50 mm graded crushed granite stone aggregate) louvres and jallies, 25mm thick (measured solid), including all mouldings but excluding frame and setting in cement mortar 1:4 complete.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut of any length and diameter of neck 15 mm dia.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete.

ASHOK BISWAS

kakolil trade agencies

SK CONSTRUCTION

M/s Pintu Furniture

A N KUMAR

V CHINNA DURAI