WBPWD/SEWEC /HED /NIQ-84/2024-25

Amount

PART A: SITC OF AC MACHINE SITC of 5.0 ton capacity concealed type Split AC of rated cooling capacity-60000 BTU/hr. with 2 nos. twin rotary compressor, 2 nos. 2.5 Tr.HI Wall split AC as. IDU of rated power supply- 230V-1Ph- 50 Hz., 1 no. ODU of rated power supply- 400V-3Ph- 50 Hz. Air-flow/per IDU :- 1000 CFM as per direction of EIC. (Make: Hitachi/Carrier/Mitsubhisi Electric)

SITC of 7.5 ton capacity wired concealed type Split AC of rated cooling capacity-90000 BTU/hr. with 3 nos. twin rotary compressor, 3 nos. 2.5 Tr. HI Wall split AC as IDU of rated power supply- 230V-1Ph- 50 Hz., 1 no. ODU of rated power supply- 400V-3Ph- 50 Hz. Air-flow/per IDU :- 1000 CFM as per direction of EIC. (Make: Hitachi/Carrier/Mitsubhisi Electric)

Supplying, fabrication & fixing M.S u-channel of 6 mm thick of size (75 mm x 40 mm x 40 mm) for making platform for installation of outdoor unit of 5.0/7.5TR Concealed split AC incl. drilling 2 nos holes in each channel including cutting holes into the wall & grouting the same with cement concrete (1:1 ½ :3) etc.including supporting angle 50 mm x50mm x 6 mm in each platform as per direction of EIC.

SITC of 2.5 ton capacity non-inverter type ceilling concealed ductable Air-conditioner machine fitted suitable for Refrigerant-R410A/R-32 having PCB in metal enclosure with installation kit. The outdoor unit fixed on wall bybracket and indoor unit fixed on ceilling using sutible size tie rod incl. charging the refregerent as per direction of EIC. (/Mitsubishi Electric/Hitachi/Mitsubhisi Heavy as approve by the E.I.C.)

SITC of 1.5 ton capacity non-inverter type split Air-conditioner machine fitted with Rotary compressors suitable for Refrigerant-R410A/R-32 having PCB in metal enclosure with installation kit fixed on wall incl. Bracket & charging the refregerent as per direction of EIC. (Make: Mitsubhisi Electric/Mitsubhisi Heavy/ Hitachi)

Supply & Laying Extra Add-on items- 1/2"(for suction) & 1/4"(for discharge) copper refrigerant pipe with 9mm thick nitrile rubber insulation incl. fixing arrangement and wrapping insulation of aerotape complete in all respect for 1.5/2.5 TR A.C. Machine. as per direction of E.I.C.

Supply & Laying Extra Add-on items- 7/8"(for suction) & 1/2"(for discharge) copper refrigerant pipe with 9mm thick nitrile rubber insulation incl. fixing arrangement and wrapping insulation of aerotape complete in all respect for 7.5 TR A.C. Machine. as per direction of E.I.C.

Supply & Laying Extra Add-on items- 5/8"(for suction) & 3/8"(for discharge) copper refrigerant pipe with 9mm thick nitrile rubber insulation incl. fixing arrangement and wrapping insulation of aerotape complete in all respect for 5.0 TR A.C. Machine. as per direction of E.I.C.

Supply and fixing of 3 core starneded copper cable for Working Voltage up to 1100 Volts of following sizes as per direction of EIC.

3 Core 4 sq. mm. Communication Cable

4 Core 4 sq. mm. Communication Cable

4 Core 2.5 sq. mm. Communication Cable

4 Core 6 sq. mm. Communication Cable

4 Core 10 sq. mm. Communication Cable

S&F of 25mm Dia PVC drain pipe for AC drain pipe on wall, ceiling with saddles and other accessories as required and mending good damages to building works

PART A: SITC OF MORTUARY COOLER Supply, installation, testing & commissioning of CE certified6 body Modular Mortuary Cabinet as per the following details :-

1. Body (Both inside & outside) is to be made of corrosion resistant stainless steel, SS304. 2. The wall, ceiling & floor of Mortuary Cabinet will be fabricated from modular panels of Polyurethane insulation of 100% foamed having 80mm thickness &40 +/-2 kg/cum density. The blowing agent for Polyurethane insulation will be Cyclopentane having ODP( Ozone Depletion Potential)=0(Zero).The foamed panels should comply TUV standards & CCOE certification (Certificate from the manufacturer should be enclosed) 3. Internal lighting for each chamber will be of waterproof type with LEDreplaceable lamps having illumination level at least 150 lux. The lights are to be switched ON/OFF during operation of doors of chambers with limit switch. The Internal wiring should be done with 2x1.5/2.5 sqmm. FRLS wire in proper manner with proper taping & socketing. 4. The doors should be made of corrosion resistant stainless steel, SS304, properly insulated as same as wall/ceiling, moulded and externally locked, situated up front. The Locks should be made of best Quality Stainless Steel/ or Brass. 5. Mortuary unit should be equipped with microprocessor based digital control panel (Blue Star approved make) to control temp inside the cabinet between (+) 2 Deg. C to (+) 6 Deg C. 6. The carriage assembly should be telescopic type. 7. Trolleys will be made of stainless steel & sliding on telescopic rail 8. Trays will be made of SS304 stainless steel with tubular edge. 9. The finished size of the Mortuary cabinet (mm) -3165(W) x 2400(D) x 1785(H) having 3 (three) Colums& 2(two) Rows. (Make : Bluestar/Desco/Yathern/Technocom)

10. Refrigeration Unit is of split type, consisting of both evaporating and condensing unit. 11. The IDU is to be mounted on the cutout in the modular insulated ceiling of cabinet. 12. CDU will be placed on the outdoor wall of the morgue room which should be nearest to each corresponding chamber for fresh air. Between each no of IDU and CDU, Copper refrigeration pipeline with nitrile rubber insulation wrapping with PVC Aero tape &copper electrical cable will be fitted. 13. There should be 2(two) nos Refrigeration units (CDU) for each mortuary Cabinet, 1no Working & 1 no Standby to be controlled with the digital controller (Sl No-5) as per predefined setting. 14. The Refrigeration units should be factory assembled, pre-charged and tested for ready field installation. Capacity -10000 BTUH (upto 35RFT of refrigeration line)/15000BTUH(beyond 35RFTrefrigeration line). Evaporator fan capacity-1600 cfm. Evaporator coil type-copper tubes. , CDU with 10000 BTUH or CDU with 15000 BTUH

15. The scope of work includes getting approval of technical details with drawing from OEM/Manufacturer showing relative position of cabinets & CDU with electrical & control circuits inside & outside the mortuary room with dimensions prior to installation from the EIC/Competent authority.Submission of necessary certificates from the OEM/Manufacturer.Warranty should be provided- 12¬ months from the date of installation. 16. The scope of work also includes making of holes, fixing of brackets, control unit & all other items, power & control circuit wires/cables in between IDU & CDU and mending of damages made during installation. All the cabinets, Doors, Digital Controllers, IDU, CDU, Locks, Trolleys, Trays are of complying specification of 6 body Modular Mortuary Cabinet (Make – Blue Star, Model- BMC-610-SS)/Acmas Technologies Inc./Desco. If any assembled material is supplied or installed penal action will be taken as per existing rule.

Terms And Condition 1. The Agency Must procure the Materials from the Manufacturer/OEM or from their authorizes. Sales channel so that the standard warranty/sopport of the manufacturer/OEM becomes applicable to the products to be delivered and installed by them. 2. Documents that authenticates such procurement from the manufacturer/OEM or from their authorizes sales channel so that the stranded warranty/sopport should be sent from the e-Mail of the manufacturer/OEM/Authorizes sales channel to the e-Male of Engineer-In-Charage and hard copy of it to be submitted during execution of work/submission of bill. 3. If any refurbished material is sipplied ABD installed, penal action will be taken as per existinf rules.

GITANJALI ELECTRONICS AND ELECTRICALS (BID ID -5865682)

SNOWLINE ENGINEERS (BID ID -5869051)

P. M. COOLING AND ENGINEERING CO (BID ID -5877339)

NEW ENVIRONMENT CONTROL CO. (BID ID -5875250)

ANUPAMA ENGINEERING WORKS (BID ID -5875428)