CONSTRUCTION OF PARKING SHED FOR ONE CFT AND 02 MRS AT AFS KANPUR

Amount

Surface excavation in soft/loose soil, not exceeding 30cm deep and averaging 15cm deep and getting out, complete all as specified and directed.

Excavation in trenches by mechanical means, not exceeding 1.5 m wide and n. exc 1.5 m in depth for laying of cable for soft/loose soil and getting out all complete as specified and directed.

Excavating in trenches, n.exc 1.5m wide and exc 1.5m but not exc 3m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and exc 1.5m but not exc 3m in depth and getting out in hard/dense soil, complete all as specified and directed by the Engineer-in-Charge

M & L for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed..

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for Formwork to chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed.

M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, etc., work in rough finished flat surfaces of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in Chhajjas complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&Lfor providing reinforced cement concrete M-25 Design Mix using 20mm graded aggregate as in beams, cantilevers, bressmummers, lintels over 1.5 m span complete all as directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 1.5 KM but not exc. 5 KM and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L brick work in cement mortar (1:6) using Fly ash bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified.

M&L brick work in cement mortar (1:4) using fly ash bricks, straight or curved in plan any radius complete all as specified.

M&L for rendering 15 mm thick cement plaster in C:M 1:6 on fair face of brick work or concrete surface finished even and smooth without using extra cement complete all as specified.

M&L for rendering 15 mm thick cement plaster in C:M 1:4 on other than fair face of brick work or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M & L for 5 mm th rendering in CM (1:3) over soffit and sides of RCC column, slab, landing , waiste slab, chajja, roof projection etc. complete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

M & L for Preparation of newly plastered surfaces on wall complete and applying three coats of white wash complete all as specified and directed.

M & L for Preparation of newly plastered surfaces on ceiling complete and applying three coats of white wash (white or tinted) complete.

M&L preparation of new plastered surface and applying two coats of Exterior emulsion paint over one coat of wall primer including over and including 1mm thick wall care white cement putty complete all as specified and directed.

M & L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement complete all as specified and directed.

M & L for 100 mm thick Cement concrete 1:4:8 type D2 using 40mm graded stone aggregate in sub base, finished rough to receive finishes complete all as specified and directed.

M & L for 75 mm thick Cement concrete 1:2:4 type B-2 using 40mm graded stone aggregatefinished fair and even without using extra cement complete all as specified and directed.

M&L for Forming construction joint 30 mm x 10 mm filled with sealing compound Grade ‘A complete all as specified and directed

M&L for Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound upto 150mm thick PCC, Grade ‘A complete all as specified and directed

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound filled with Grade 'A' complete all as specified and directed.

M & L for PCC floor as in ramp in cement concrete 1:1.5:3 type A-1( using 20mm graded stone aggregate) including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in ramp slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for 10 mm thick cement plaster in C:M 1:3 finished even and smooth above dado/ skirting complete all as specified and directed.

M & L for and applying bitumen primer @ 0.40 Ltr per sqm and applying water proofing treatement using 3mm thick APP modified polymeric membrane with Gravel/Granular finishes, sealed with torch application laid over & including 10 mm thick screed bed in CM 1:3, overlaps shall be sealed with torch application complete all as specified & directed. Make :- (a) M/s STP Ltd., “STP HOUSE”, 570, Udyog Vihar, Phase-II, Gurgaon (Haryana) (b) M/s IWL India Ltd (Hyperplas), C&D Lakhsmi Bhawan, 609, Anna Salai, Chennai-600006 (c) M/s Bengal Bitumen (Bengal Supermat), B-53, Sarita Vihar, New Delhi-110044

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

M & L for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block glazed, coloured any shape and size confirming to IS 15658-2006 of 80mm thick, M-40 grade with grey cement and pigment over and including 50 mm thick sand cushioning complete all as specified and directed.

Supply, laying, testing and commissioning of LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 core, laid in trenches/duct/ laid on wall etc. incl suitable size lugs, thimbles, glands,GI nuts and bolts, washers, insulation tape etc. complete all as specified and directed.

Supply and Fix LED flood light luminaries 150-160 watt comprising of pressure die cast aluminium housing and high purity electro polished anodised aluminium heat shrink with an option of toughened glass of UV stabilised polycarbonate cover for lamp campartment complete all as specified and directed.

Supply and fix aviation light luminaries comprising of aluminium housing and high purity electro polished anodised aluminium heat shrink with an option of toughened glass of UV stabilised polycarbonate cover for lamp campartment complete all as specified and directed.

Supply, installation, commissioning and testing of outdoor type LT panel (CPRI Approved) made out of 3.15 mm thick CRCA sheet metal, double door and suitable MS angle iron base frame, cubical type floor mounted 3 Phase, 4 Wire, 415 Volts properly insulated aluminium bus bar- 04 Nos having capacity 240 amps on phase & neutral, dust and vermin proof, both side open with locking arrangement comprising of multifunciton meters with 3 lines LCD display of voltage, current and frequency and power factor of size 96x96 Sqmm, suitable ratio CT, RYB phase indicator-03 No. danger board plate, duly painted internally and extenally with powder coated, flxing in position by provision of platform suitable size buit with brick work in CM (1:4),15 mm thick plastering in CM (1:6) including glands, lugs, thimbles for all incoming and outgoing cable comlete all as directed of suitable sizes for following:- (a) Incoming : MCCB 160 Amp, 25KA, 415V, 4Pole-01 No, lcs=100% Icu (b) outgoing : MCCB 63 Amp, 25 KA,4Pole, 415V-04 No lcs=100% lcu

M & L for dry Ganga Sand cushioning in trenches for protection of cable complete all as specified and directed.

M & L for well burnt brick sub class B old size laying in trenches for cable protection complete all as specified and directed.

Removing of excavated surplus soil to a distacne n.exc 50 m and depositing where dircted at a level not exceeding 1.5m above the staring point complete all as specified and directed.

Supply and laying in trenches GI pipe light grade with fitting of size 50 mm bore for protection of cable complete all as specified and as directed.

M & L for cutting of PCC / Hard standing /WBM road not exceeding 45 cm in width not exceeding 60 cm in depth for passing of cable and making good of disturbed surface to match with the existing surfaces by using old and new material i.e bitumen/PCC (1:3:6) type C-1 complete all as specified and directed.

Material and labour for boring of holes under road, pavement, runway, taxi track, hard standing for cable protection complete all as specified and directed.

M & L for earthing complete with GI earth plate electrode of size 600 mm x 600 mm x 6mm thick buried directly to ground vertically to a depth not less than 2.25 Mtr below the ground level with top edge of earth plate not less than 1.5 Mtr below normal ground level connected to GI strip 32mm x 6 mm as earthing lead protected with 50mm dia light grade GI pipe, filling around with cahrcoal dust and salt including excavation, returning filling of earth work and disposal of surplus soil to a distacne not exceeding 50 mtr and connected to GI strip by means of GI nuts, bolts and washers strip connected to earth plate including chamber PCC 1:3:6 type C-1 using 20mm graded stone aggregate and pre cast RCC cover 40 mm thick reinforced with 6 mm dia round at the rate of 75 mm C/C both way with 12mm dia mild steel plain bar lifting handle 2 Nos funnel with wire mesh 20mm dia GI pipe light grade watering pipe and framework complete all as directed. Note :- GI Strip above 7.5 m length shall be measured & paid separately.

Supply and fixing GI strip 32 x 6 mm for extension of earth and connected to equipment or panel etc. complete all as specified and directed

Supply, laying, testing and commissioning of unarmoured, electric power cable (heavy duty) 1100 Volts grade with stranded aluminium conductor twin core of size 6 Sqmm laid on wall/ pole etc. incl suitable size lugs, thimbles, glands, GI Nuts and bolts, washers, insulation tape etc complete all as specified and directed.

M & L for concealed point wiring on wall and surface on ceiling/roof with necessary fixing arrangements with PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade drawn in and including rigid non metallic white / ivory PVC conduit medium grade ISI marked not less than 19 mm dia with all conduit accessories/ fittings such as junction boxes, bends, tee, elbow etc including anodized MS sunken boxes made out of MS sheet of thickness not less than 1.5 mm with earth dolly suitable for mounting modular switches incl modular metal flush boxes and modular face plate as per site requirement for fixing of modular switches / sockets, fan regulators, including PVC-FRLS insulated and unsheathed copper multi-stranded conductor of size 1.5 Sqmm, 1100 volts grade for continuous earthing including cutting the chases and making good the surface by cement mortar (1:3) and for matching / finishing of new surfaces either by means of plaster of peris/ Putti or distemper / colour wash with same existing colour surfaces all as specified and directed by Engineer-in-Charge for the following :- For one light, fan, call bell point

-Ditto- all as per item No 55 here-in-before but For one socket point controlled by one switch on independent board.

-Ditto- all as per item No 55 here-in-before but For one socket point controlled by one switch on same board.

All as per item No 55 here-in-before but for power point wiring with 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable and 2.5 Sqmm PVC-FRLS insulated, unsheathed, copper conductor, stranded 1100 volt grade cable as continuous earth lead.

M & L, switch flush type single pole one way 5 Amps, 240 volts, white finish complete all as specified.

M & L, switch flush type 15 Amps, 240 Volts single pole white finish complete all as specified.

M&L, socket outlet 5 pin, 5 Amps flush type white finish complete all as specified.

S&F, socket outlet 2 in 1, 3 pin, 5/15 A, flush type universal, 240 V white finish complete all as specified.

S&F, in replacement, ceiling rose, surface backlite, 65 x 20 mm three terminal

S&F double door metallic sheet metal enclosure for DB when MCBs to be used SPN 8 ways, 240 V with 200Amps rated bus bar complete fixed properly in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

Supply & fixing, testing and commissioning MCB SP 240 volt 6 Amp to 32 amp 10 KA capacity having C-curve characteristics connected with suitable lugs complete all as specified & directed.

-Ditto- all as per item No 65 but of SPN 32 Amps complete all as specified and directed.

M & L sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 2.5 sqmm drawn in new/existing MS/PVC conduit with 2.5 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire complete all fixing accessories such as couplers lock, nuts, sadles, pipe hooks etc fixed properly complete all as specified and directed. Note : (i) Two single core cable and one run of earth copper conductor will be measured and paid as one unit length. (ii) PVC Conduit if required shall be measured and paid separately under respective item.

M & L sub main wiring with two single core PVC-FRLS insulated unsheathed multi stranded copper conductor cable of size 4 sqmm drawn in new/existing MS/PVC conduit with 4 Sqmm PVC-FRLS insulated unsheathed multi stranded copper conductor as a continuous earth wire complete all fixing accessories such as couplers lock, nuts, sadles, pipe hooks etc fixed properly including taking down old unserviceable sub main wiring complete all as specified and directed. Note : (i) Two single core cable and one run of earth copper conductor will be measured and paid as one unit length. (ii) PVC Conduit if required shall be measured and paid separately under respective item.

S&F rigid non metallic medium white / ivory PVC conduit medium grade ISI marked of size not less than 20 mm dia concealed position on wall and surface in roof/ceiling inclusive all fitting such as tee, bends, reducer, elbow, bell mouth, tube ends and all fixing accessories such as couplers lock, nuts, saddlers, pipe hooks etc fixed properly on as in concealed position incl cutting chasing & making good to disturbed surfaces & matching with the existing colour of wall/floor etc all as directed.

S&F energy saver LED light fitting 40 watt, 230 Volts, single tube mounting including LED Tube/ LED blocks 40 Watt ,Lumen OUTPUT NOT LESS THEN 100 LM /WATT with 50000 burning Hours, PF = 0.95 complete with electronic driver LED Printed board, end cover, connector box etc and accessories, prewired, LED including required fixing arrangements and electrical connection three core copper cable from ceiling rose to led light fitting all as directed . Make: PHILIPS BN100C LED 40S-6500 PSU L120GR or Wipro Cat Part No LL24-541-xxx-57-xx / equivalent in Havells

S &F LED Building Security Light 110 watt orf alumenium PDC housing glass cover with IP 66 protection all as specified and directed complete including taking down old unserviceable fitting .Make wipro cat No LR02-122-XXX-57-G2 or Philips Cat No BRP 409 LED 115 CWSLA FG PSUGR V2 or equivalent in Havells

M&L for XLPE insulated, armoured heavy duty electric cable with stranded aluminium conductor, 1100 volts grade 16 sqmm 2 core laid in trenches/panel or passing through pipe including connecting with suitable lugs, nuts and bolts and testing complete all as specified and directed

aarohi nirman company

M/s R.V. Constructions

DHARM ENTERPRISES

M/S SDS Construction Co.

AMRENDRA CONSTRUCTIONS