Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹3.1 Cr
EMD Value
₹6.1 L
Closing Date
4 Dec 2026, 3:30 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Station Development
Above/Below/Par
DRM/WORKS
14 conditions · 2 needing a document upload
10.2 - Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, as provided at Page 42 of tender documents, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
10.1 Technical Eligibility Criteria: (a)The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (1)In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b)(2)In such cases, what constitutes a component in a composite work shall be clearly pre- defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Non-submission of the Completion certificate issued by the Competent Authority shall result into summarily rejection of the offer.
Defination of Similar Work :- 3.1 - Any Civil Construction or repair work
24 conditions · 3 needing a document upload
The 'Class-I local supplier/ 'Class-Il local supplier' shall be required to indicate percentage of local content in the material being offered. Please enter 0 for fully imported items and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions. Format for submission of local content is attached as Annexure-E. In case of works costing more than Rs 10 crore, "Class-I local supplier/ 'Class-II local supplier' shall be required to provide a certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of local content. ( Click here to download Format)
"The said suppliers of goods and/or services would be subject to GST Act and Rules as applicable from time to time. Tenderers are requested to submit their offers as per GST Tax regime. All the bidders/tenderers should ensure that they are GST compliant and their quoted tax structure/rates are as per GST Law"
Successful tenderers are required to submit the number of labour to be employed for this particular work. Also the list showing names, along with all other details, of male and female workers employed in this work, should be submitted to office, at the time of submitting performance guarantee and before executing contract agreement. They should also ensure that 1) The payment to the contract labour should be made through bank/cheque. 2) Identity Cards should be issued to all contract workers. 3) Necessary steps should be taken to deduct provident fund from the payment made to contract labour and ensure that the same is credited to their Provident Fund account. 4)Medical facilities from ESI should be ensured, if applicable.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderers are required to submit a copy of cancelled cheque in order to facilitate the payments regarding refund of EMD etc. in their proper accounts.
Indian Railways Standard General Conditions of Contract, April 2022 (GCC, April 2022) has been introduced and available on website with all correction slips issued up to date for inviting tender and same will be applicable for this tender. Advance Correction Slip No. 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 and 12 to Indian Railways Standard General Conditions of Contract, April - 2022 circulated by the Railway Board vide letter No. 2022/CE- I/CT/GCC-2022/Policy dated 14.07.2022, 13.12.2022, 26.04.2023, 07.08.2023, 20.10.2023, 21.12.2023, 25.09.2024, 20.12.2024, 09.01.2025, 04.03.2025, 13.03.2026 and 12.08.2026 are applicable to this tender.
I/We agree to carry out all works with use of modern equipments of required capacity for the work without extra payment. The decision of railway engineer shall be final and binding in this regard.
It is the responsibility of contractor to arrange the payment of the labour employed for the work through bank and to deduct PF as per the provisions of Minimum Wages Act.
The quantities shown above are approximate and to give a general guideline. Railway reserves a right to increase, decrease or to delete any of the items mentioned in schedule.
As per ACS 1 to GCC April 2022, issued vide Railway Board's letter dt. 14.07.2022, PVC Clause shall be applicable only in tenders having advertised value above Rs. 2 Crores provided to the provisions as per clause 46A-1. Tenderers should take a note and quote their rates accordingly.
In case Civil work tenders, the quantity of cement required in the items where necessary, will be used by the contractor on the same rates as accepted in tender, as per the quantity mentioned against each item in USSOR/DSR, though not mentioned in tender schedule.
Tenderers are advised to quote their rates including all type of taxes and levies etc. to be paid by them. Any extra payment will not be made on account of taxes/Levies etc., in excess of Contract Agreement Value,
In case of submission of Bid Security in the form of Bank Guarantee, a scanned copy of Original BG valid for a period of 90 days beyond the validity period of tender, and addressed in favour of Sr.DFM/WCR/BPL, shall be uploaded on IREPS portal while applying for tender. And As per ACS 2 to GCC April 2022, circulated vide Railway Board letter dt. 13.12.22, original BG should be delivered in person to the Concerned Official in Office before closing date for submission of bid (i.e. Excluding the last date of submission of bid) without fail. Any failure in this connection shall lead to summary rejection of bid.
The maintenance period for the work shall be 24 months.
Ashoknagar:- Upgradation of left over second entry including station building with facade, entry gate, roads and parking area.
WCR-BPL-W-26-27-N-36-122~WCR
WCR-BPL-W-26-27-N-36-122
Open
Works - General
12 Months
Bhopal, Madhya Pradesh
₹0
₹6.1 L
12 Nov 2026
12 Nov 2026
20 Nov 2026
98 items across 2 schedules · ₹4,25,21,235.61 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | All kinds of soil | cum 742.05 | — | 177.5 | 1,31,713.88 |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum 595.14 | — | 196 | 1,16,647.44 |
| 3 | All kinds of soil | cum 1855.12 | — | 126.8 | 2,35,229.22 |
| 4 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. | cum 302.1 | — | 2,123.75 | 6,41,584.88 |
| 5 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum 142.05 | — | 7,878.5 | 11,19,140.93 |
| 6 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm 219.96 | — | 392.15 | 86,257.31 |
| 7 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm 421.24 | — | 842.5 | 3,54,894.7 |
| 8 | Suspended floors, roofs, landings, balconies and access platform | Sqm 324.24 | — | 927.25 | 3,00,651.54 |
| 9 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm 730.14 | — | 736.4 | 5,37,675.1 |
| 10 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm 1312.24 | — | 961.3 | 12,61,456.31 |
| 11 | Weather shade, Chajjas, corbels etc., including edges | Sqm 30.24 | — | 951.1 | 28,761.26 |
| 12 | Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) | Sqm 1000 | — | 384.3 | 3,84,300 |
| 13 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 48513.6 | — | 107.85 | 52,32,191.76 |
| 14 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum 146.91 | — | 9,504.75 | 13,96,342.82 |
| 15 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum 257.37 | — | 9,860.4 | 25,37,771.15 |
| 16 | Add for using extra cement in the items of design mix over and above the specified cement content therein. | Quintal 274.76 | — | 733.5 | 2,01,536.46 |
| 17 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum 29.28 | — | 7,370.65 | 2,15,812.63 |
| 18 | Cement mortar 1:4 (1 cement : 4 coarse sand) | cum 269.16 | — | 9,344.35 | 25,15,125.25 |
| 19 | Granite work | Metre | 286 | 510.95 | 1,46,131.7 |
| 20 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including:(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF /Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminium Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. | Sqm 842.56 | — | 5,015.05 | 42,25,480.53 |
| 21 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 21.6 | 3,167.95 | 68,427.72 |
| 22 | 300x16 mm | Each | 12 | 303.25 | 3,639 |
| 23 | 125 mm | Each | 12 | 66.25 | 795 |
| 24 | Single rubber stopper | Each | 10 | 39.6 | 396 |
| 25 | 200 mm | Each | 20 | 186.65 | 3,733 |
| 26 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg 9140 | — | 133.7 | 12,22,018 |
| 27 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). | Kg | 20 | 141.7 | 2,834 |
| 28 | Hot finished welded type tubes | Kg 10121.76 | — | 194.4 | 19,67,670.14 |
| 29 | Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. | Each | 12 | 220.65 | 2,647.8 |
| 30 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. | Kg 1613.3 | — | 97.2 | 1,56,812.76 |
| 31 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works | Kg 1080 | — | 172.6 | 1,86,408 |
| 32 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). | Kg | 225 | 772.4 | 1,73,790 |
| 33 | Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides | Sqm 60.48 | — | 844.7 | 51,087.46 |
| 34 | Size of Tile 600x600 mm | Sqm | 54 | 1,553.45 | 83,886.3 |
| 35 | Size of Tile 1000x1000 mm | Sqm 203.65 | — | 2,089.65 | 4,25,557.22 |
| 36 | Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. | Sqm 139.68 | — | 3,186.7 | 4,45,118.26 |
| 37 | Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent | Sqm 397.67 | — | 4,481.3 | 17,82,078.57 |
| 38 | 1.60 mm thick with zinc coating not less than 350 gm/m2 | Metre | 31 | 1,863.9 | 57,780.9 |
| 39 | 75 mm diameter | Metre | 80 | 248.8 | 19,904 |
| 40 | 110 mm diameter | Metre | 60 | 377.4 | 22,644 |
| 41 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm 760.96 | — | 738.65 | 5,62,083.1 |
| 42 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. | Sqm 116.58 | — | 2,215.15 | 2,58,242.19 |
| 43 | 1:4 (1 cement: 4 fine sand) | Sqm 7008.55 | — | 347.05 | 24,32,317.28 |
| 44 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm 4205.13 | — | 185.65 | 7,80,682.38 |
| 45 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm | Sqm 2803.42 | — | 193.7 | 5,43,022.45 |
| 46 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | Sqm 7008.55 | — | 156.05 | 10,93,684.23 |
| 47 | One or more coats on old work | Sqm 51.84 | — | 102.8 | 5,329.15 |
| 48 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 110 | 2,434.25 | 2,67,767.5 |
| 49 | In cement mortar | cum | 6 | 2,060.2 | 12,361.2 |
| 50 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. | Sqm | 5.4 | 266.45 | 1,438.83 |
| 51 | 90 mm to 45 mm size stone aggregate | cum 143.15 | — | 2,098.4 | 3,00,385.96 |
| 52 | 63 mm to 45 mm size stone aggregate | cum 143.15 | — | 1,636.05 | 2,34,200.56 |
| 53 | 53 mm to 22.4 mm size stone aggregate | cum 143.15 | — | 1,842.3 | 2,63,725.25 |
| 54 | Moorum | cum | 300 | 768.25 | 2,30,475 |
| 55 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . | cum 143.15 | — | 1,046.95 | 1,49,870.89 |
| 56 | Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete. | cum 286.3 | — | 7,993.8 | 22,88,624.94 |
| 57 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in- Charge. | Sqm | 36 | 2,017.6 | 72,633.6 |
| 58 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 1 | 6,767.4 | 6,767.4 |
| 59 | W.C. pan with ISI marked white solid plastic seat and lid | Each | 1 | 6,515.55 | 6,515.55 |
| 60 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps | Each | 2 | 2,648.85 | 5,297.7 |
| 61 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer | Each | 2 | 3,960.55 | 7,921.1 |
| 62 | 32 mm dia | Each | 20 | 103.9 | 2,078 |
| 63 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | Each | 10 | 53.25 | 532.5 |
| 64 | Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms | Each | 4 | 115.3 | 461.2 |
| 65 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. | Each | 2 | 14,999.15 | 29,998.3 |
| 66 | Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal. | Each | 2 | 18,088.45 | 36,176.9 |
| 67 | 15 mm nominal dia Pipes | Metre | 50 | 286.8 | 14,340 |
| 68 | 20 mm nominal dia Pipes | Metre | 50 | 335 | 16,750 |
| 69 | 25 mm nominal dia Pipes | Metre | 50 | 401.55 | 20,077.5 |
| 70 | 50 mm nominal dia Pipes | Metre | 100 | 934.15 | 93,415 |
| 71 | 15 mm nominal dia Pipes | Metre | 50 | 497.8 | 24,890 |
| 72 | 25 mm nominal dia Pipes | Metre | 100 | 627.25 | 62,725 |
| 73 | 32 mm nominal dia Pipes | Metre | 200 | 739.3 | 1,47,860 |
| 74 | 150 mm nominal dia Pipes | Metre | 200 | 6,822.7 | 13,64,540 |
| 75 | 50 mm nominal bore | Each | 5 | 1,026.65 | 5,133.25 |
| 76 | Horizontal | Each | 5 | 1,371.2 | 6,856 |
| 77 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre 2000 | — | 11 | 22,000 |
| 78 | 15 mm nominal bore | Each | 20 | 798.95 | 15,979 |
| 79 | 15 mm nominal bore | Each | 10 | 670.45 | 6,704.5 |
| 80 | 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 12 | 125.6 | 1,507.2 |
| 81 | 15 mm nominal bore, 86 mm long, weighing not less than 88 gms | Each | 12 | 118.5 | 1,422 |
| 82 | 15 mm nominal bore, 98 mm long, weighing not less than 75 gms | Each | 12 | 112.8 | 1,353.6 |
| 83 | Providing and fixing PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms | Each | 12 | 156.9 | 1,882.8 |
| 84 | 15 mm nominal bore with 30cm length | Each | 6 | 96.35 | 578.1 |
| 85 | 15 mm nominal bore with 45 cm length | Each | 6 | 121.9 | 731.4 |
| 86 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 280 | 530.9 | 1,48,652 |
| 87 | Powder coated aluminium (minimum thickness of powder coating 50 micron) | Kg | 210 | 634.45 | 1,33,234.5 |
| 88 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) | Sqm 60.48 | — | 1,505.25 | 91,037.52 |
| 89 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to paid separately) | Sqm | 12 | 5,325.9 | 63,910.8 |
| 90 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. | Kg 604.8 | — | 414.3 | 2,50,568.64 |
| 91 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminium sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised /Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimensional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon separator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces | Sqm 151.2 | — | 3,510.5 | 5,30,787.6 |
| 92 | Sqm 17.28 | — | 3,671.5 | 63,443.52 | |
| 93 | Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevant Item*). "(i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. | Sqm | 36 | 2,450.15 | 88,205.4 |
| 94 | 30 mm thick | Sqm 151.2 | — | 4,764.2 | 7,20,347.04 |
| 95 | 18 mm thick | Sqm 151.2 | — | 2,992.9 | 4,52,526.48 |
| Schedule total | ₹4,22,89,985.01 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
TDGCCMarch26.pdf
ATTACHMENT
ACS11.pdf
ATTACHMENT
ListofApprovedBrand.pdf
ATTACHMENT
PublicProcurementOrder_1-1-12.pdf
ATTACHMENT
Annualcont.turnoverformatAnn.VIB.pdf
ATTACHMENT
Annexure-E.pdf
ATTACHMENT
BuildingPlans.pdf
ATTACHMENT
Circulation-Divyangjan.pdf
ATTACHMENT
Circulation-Pedestrian.pdf
ATTACHMENT
Circulation-Vehicular.pdf
ATTACHMENT
MasterPlan.pdf
ATTACHMENT
SignagePlan.pdf
ATTACHMENT
DrainagePlan.pdf
ATTACHMENT
Specialconditionofcontract..pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .