Providing E-Sewa Kendra in District Munisiff cum Judicial Magistrate Court building at Boothapandy in Kanniyakumari District.

Towards charges for supplying and fixing of computer table arrangements of size 1.30 x 0.65 x 0.75m including key board, cupboard arrangements with both side laminated sheet with 19mm thickness of following size with includes cost of labour,cost of materials,cost of transportation etc.,complete complying with standard specification and as directed by departmental officers.

Manufacturing and supply of Teak wood chairs of size 0.55 x 0.55 x 0.90 m with cushion seat and back of knitted wire finish. The chair has to be furnished with teak wood planels of following specification. (1) The vertical posts legs are made with frames of size 0.05 x 0.30m (ii) The tie member at seat is made outof teak planks of size 0.05 x 0.30m (iii) The tie member at bottom to inter connect the legsis of 0.02 x 0.03m (iv) The handle is made from teak wood planks of size 0.04 x 0.03m. The seat and back are made with finished Teak wood planks and covered withknitted wire as approved by materials, labour charges, polish, transportation and excluding GST and all other incidental charges etc. complete as directed by departmental officer.

Supplying, fabricating, erecting and fixing Calcium Silicate Board False Ceiling upto a ceiling height of 4.5m from floor level.

Supply of Airfort chair of 1.80 metre length (three seated). The rate includes cost of all materials, labour, polish , transportation and excluding GST and all other incidental charges etc. complete as directed by departmental officer.

Providing cornice work for False ceiling ncluding cost of material, labour charges etc, complying with standard specification and as directed by the departmental officers. The rate shall be inclusive of finishing the edges and wall junctions with suitable lipping & cornice

Fabricating Supplying and fixing in position of Aluminium - Powder Coated matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition of size 3.50 x 2.88m. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing etc... complete complying with standard specification and as directed by the deparmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.The outer frame shall be with aluminium box section 101.60x44.45x3.18m at 2.319kg/m and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - Each., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No., Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete complying with standard specification and as directed by the deparmental officers. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Painting Old Plastered Wall Surface with One finishing coats of ready mixed (Emulsion-Exterior) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and Fixing of Aluminium open type mosquito net with outer frame for window including cost of matearial, labour charges etc complete.

Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with One coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)