Maintenance Repairs to the Community Hall at Indra Nagar in Ward No.51,East Zone.

Amount

1. Removing the old damaged AC Sheet Roofing without roof timbers as per the direction of Departmental officers etc. completed.

2. Removing and Relaying the interlock block as per the direction of Departmental officers etc. completed.

3. Dismantling the old damaged Brick or stone in cement mortar walls under 3 mtr height as per the direction of Departmental officers etc. completed.

4. Dismantling the old damaged Plain cement concrete as per the direction of Departmental officers etc. completed.

5. Scrapping of old plastered surface etc. complete as per the direction of departmental officers.

6. Providing Pile foundation of size 300 mm dia using augur including labour charges and all other tools and plants charges etc. , as per direction of dept officers. (Local Rate)

7. Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

8. Cement concrete of mix 1:4:8 (one cement fours and and eight couse aggregate) using hard broken granite stone jelly of 40 mmgauge for foundation levelling course, including shuttering, dewatering wherever necessary and laid complete complying with standard specifications and drawings and as directed by the departmental Engineers including all cost curing etc., complete I layers of not more than 15cm thick & conveyance of materials laying curing etc., complete.

9. Supply and erecting shuttering including necessary supports for plane surfaces such as RCC column footing, plinth beam, stair case etc., in all floors using mild steel sheets of 90cm X 60cm and 10 gauge stiffened with welded mild steel angle for boarding supported by casurina props at suitable intervals etc., completed complying with standard specification and as directed.

10. Supplying and erecting centering for sides soffits including supports and strutting upto 3.29m high for plain surface such as rectangular column top and bottom slabs of boxing, sill, slabs, sun shade etc., in all floors using mild steel slabs of sizes 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25x25x3mm for boarding laid over country wood joists of size 10cm x 6.5cm spaced at about 90cm C/C and supported bycasurina props of 10cm to 13cm dia spaced at 75cm C/C etc., complete as directed. Sl.No.123 C Part-II

11. Reinforced Cement concrete 1:1.5 :3 (one cement, one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete.

12. Supplying, Fabricating and placing in position mild steel or deformed steel bars for all reinforced cement concrete items of work including cost of steel transporting straightening cutting, bending, cranking binding welding etc. Including cost of binding wire MS.chairs laps to fix the reinforcement in all positions, all labour and materials complete complying with standard specifications and drawings and as directed by the departmental Engineers.

13. Fly ash Brick work in CM 1:5 (one cement & five sand) using size 9"X4 3/8"X 2 3/4" including finishing, curing, etc., complete complying with standard specification.

14. plastering the exposed surface of RCC works in cement mortar 1:3 mix 10mm thick in all floor as directed by the departmental Engineers.

15. Plastering with cement mortar 1:5 mix 12mm thick in all floor as directed by the departmental Engineers.

16. Painting with first quality emulsion paint two coats over a priming coat including through cleaning, scrapping, removal of dust and including necessary plaster of paris putty works wherever required etc., completed.

17. Painting with first quality emulsion paint two coats including through cleaning, scrapping, removal of dust and including necessary plaster of paris putty works wherever required etc., completed.

18. Painting Iron Works for doors, windows and Ventilators, Iron bars, Weld mesh, wire mesh, screen, steel bars, flats and other similar works etc., with Two coats of approved first quality of synthetic enamel paint over the existing red oxide primer in all floors. The rate is inclusive of cost of all materials and labour, brushes and scaffolding charges etc., complete complying with standard specification. (The paint to be used should be got approved by the Executive engineer before use on work.

19. Filling with Quarry Rubbish including watering and consolidation as directed by the departmental Engineers.

20. Supplying and Laying Rubber Moulded Hydraulic Pressed Paver Block Providing and laying of 83 mm thick high strength of Hydraulic Pressed Paver Block in size of minimum compressive strength of 40 N/mm2 In uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including leveling the base perpareation of pavers as sub base, stone dust cushion 150 mm thick laying out of pavement cut the pieces to fix the edge vibring the paversl sweeping transporting loading unloading of laying paver block as per the standard specifications

21. Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification.

22. Paving the floor with polished Shahabad stones slab of size below 600x600x20mm thick machine cut edges over the existing bed of concrete with cement mortar 1:3 (one cement and three sand) to 20mm thick in all floors over white cement slurly layer of 3mm thick over this laid in situ and pointed with white cement neatly and fixed in position so as to make perfectly smooth and shining to the alignment including cutting the shahabad to size with machine cutting, polishing using different grade of corborandum stone, oxalic acid, tin oxide etc., and including hire charges or polishing machinery etc., completed.

23. Supplying and fixing with galvanished iron sheet (corrugated) 24 gauge thick including necessary bolt, nuts and bitumen washed etc., completed.

24. Supply and delivery and fixing of 1000 lit. capacity HDPE tank as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,

25. Wiring with 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated unsheathed single core copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light / fan point (for electronic regulator) (5 points per coil)

26. Wiring with 2x1.5 Sqmm(22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe open in wall and ceiling with PVC accessories, in flush with wall, with 150x100x113mm TW switch box with 3mm thick Hylem sheet cover for 5A 3 pin non interlocking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the open portion with suitable colour for open PVC plug point.

27. Wiring with 2x4 sq.mm PVC insulated unsheathed SC.CU.Conductor of 1100V grade in suitable PVC rigid pipe open in wall and ceiling with PVC accessories in flush with wall,with 150mm x100mmx113mm TW switch 15A 3Pin non interlocking CS Plug with continous earth wire connection of 14 SWG TC wire and making good of the open portion with suitable colour for open PVC Plug Point

28. Supply and fixing of single box type 4'36W fluorescent fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting.

29. Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18").

30. Conveyance of Surplus earth from Work site to city outer 0 to 15 Km distance including loading, unloading, transportion and all labour charges as per the direction of departmental officers etc., completed.

31. Supply and fixing of WT bulk head fitting with guard suitable for 11W CFL lamp with CFL 1 No. WT bulk head fitting for 11W CFL.

S.Sudhagar