REPAIRS TO SUNKEN FLOOR, ROOF TREATMENT, PERIODICAL SERVICES AND CERTAIN BR REPAIRS AT ZONE - II OF DRDO COMPLEX, PHASE-I, C V RAMAN NAGAR, BENGALURU

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for; and disposing of debris outside MD land complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises and disposing of debris outside MD land complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water, etc., and disposing of debris outside MD land complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area of opening not exceeding 1.5 sq m each all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area of opening exceeding 1.5 sq m, but not exceeding 4 sq m each all as specified and as directed.

Taking down shutters of any description of area exceeding 1 sq m and not exceeding 2 Sq m each complete all as specified and as directed.

Repair / Re-securing, easing, adjusting & re-fixing door shutters of any description in the same opening after laying of tiles, area of shutter exceeding 1 sq.m but not exceeding 2 sq m each, including making good the disturbed surfaces to match the existing, complete all as specified and directed.

Material and labour for Plain Cement Concrete (1:5:10) type E2, using 40 mm graded stone aggregate as in sunken slab filling, mass concrete etc., complete all as specified and as directed.

Material and labour for Plain Cement Concrete (1:3:6) type C0, using 12.5 mm graded stone aggregate as in filling the Chowkats/frames complete all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

Supply and fix, 30 mm thick Factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete including Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, including making good to jambs with cement mortar (1:4) and finished to match with existing surface complete all as specified and as directed.

All as per Serial Item No 12 here-in-above, but except frame.

Supply and fix, 35 mm thick Factory made Second class hardwood Glazed, gauged and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to Chowkats all as specified and as directed.

Supply and fix 35 mm thick plain framed paneled factory made shutters (two panel) with II nd class hardwood rail and style with lock rail and panel of 12 mm BWP commercial ply with commercial veneer on both faces. The size of rail and style as per IS - 1003 Part - I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and fix Continuous (piano) hinges, mild steel, bright finish or electro-galvanised, width of flap when opened shall be not less than 30 mm, complete all as specified and as directed.

Supply and fix, Stainless steel Butt hinges, 100 mm long fixed with screws complete all as specified and as directed.

Supply and fix in repairs, Floor door stopper, 150 mm length of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fix, Floor door stopper, 150 mm length of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fix in repairs, single action spring hinges, 100 mm size, mild steel with steel wire spring, stove enameled black fixed in repair including necessary welding to door frame complete all as specified and as directed.

Supply and fix, single action spring hinges, 100 mm size, mild steel with steel wire spring, stove enameled black, including necessary welding to door frame complete all as specified and as directed.

Supply and fix in repairs, Magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Supply and fix, Magnetic ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed.

Supply and fix in repairs, stainless steel soft closing hinges, suitable for modular kitchen complete all as specified and as directed. (Make : Godrej or techno commercial equivalent).

Taking down unserviceable boards as in shelves of cupboards, doors, etc., supply and fix 18/19 mm thick plywood, Grade 1 quality, interior grade, with decorative face veneers on one side and other side balancing white, fixed in shutters / shelves, complete all as specified and as directed.

Supply and fix in repairs, 100 mm long fancy type stainless steel handles and fixing with screws complete all as specified and as directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long all as specified and as directed.

Supply and fix 150 mm Aluminium extruded alloy anodized handles, cast type complete all as specified and as directed.

Supply and fix in repairs, mild steel 40 mm dia cupboard knobs, fixed with nut, screws, washers, bright finished, complete all as specified and as directed.

Supply and fix in repairs, stainless steel, drawer channels of length 0.5 m suitable for modular kitchen, complete all as specified and as directed.

Supply and fix in repairs, locks suitable for post box with minimum 2 Nos of keys, complete all as specified and as directed. Make : Godrej or technocommercial equivalent makes specified here-in-after.

Supply and fix in repairs, 100 mm size Mortice rim lock (4 lever), vertical type, brushed steel suitable for 25 to 40 mm thick doors screwing complete all as specified and as directed.

Taking down tubular curtain rod, supply and fixing drapery rod, decorative type, made of 25 mm dia stainless steel (wall thickness not less than 0.63 mm), bright finish, colour and pattern as approved by GE, complete all as specified and as directed. (Note : Price shall not be less than 100/- per RM, Make : Aerolux / Vista / MEC)

Taking down brackets for curtain rod, supply and fixing stainless steel brackets suitable for drapery rod of 25 mm dia, with wall thickness of 0.63 mm thick, bright finish, colour and pattern as approved by GE, complete all as specified and as directed. (Make : Aerolux / Vista / MEC)

Supply and fix, Pressed steel door frame of size 125 x 60 mm using 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

Supply and fix, Pressed steel door frame of size 105 x 60 mm using 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

Taking down existing roof treatment of any type, preparing the roof top surfaces, by sweeping and removing all loose dirt, providing cement screed bed as mentioned bleow on prepared surface and providing APP based polymeric membrane minimum weighing 3 kg / sq.m and minimum 3 mm thick reinforced with polyester non woven fabric (weight not less than 150 gms / sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 litre/sq.m by torched application, complete all as specified and directed. The complete roof treatement shall be consisting of as under and rate quoted shall deemed to inlcude for :- (i) 10 mm thick cement screed bed in CM 1:3 mixed with water proofing compound (Supply only water proofing compound will be measured and paid for separately under respective item) (ii) Applying one coat of bituminous primer conforming to IS-3384 @ 0.3 litre / sq.m (iii) Laying of APP based membrane of specified thickness and weight. (iv) All side and end laps shall be trowelled and finished with sealant to ensure proper bonding and effective treatment (v) Applying one coat of aluminium paint @ 100 ml / sq.m

Material and labour, for padding concrete / leveling course over slabs with Plain cement concrete (1:2:4), type B0 (using 12.5 mm graded stone aggregate) mixed with water proofing compound, laid to achieve proper slope as per site conditions, surfaces finished fair to receive screed bed and water proofing treatment, complete all as specified and directed. Note: Supply only water proofing compound will be measured and paid for separately under respective items.

Material and labour, for 75 mm thick Plain Cement Concrete (1:4:8), type D2, using 40 mm graded stone aggregates as in pavings / sub-bases laid in panels, finishing the surfaces even and fair complete all as specified and as directed.

Material and labour, for 25 mm thick Plain Cement Concrete 1:2:4, type B0, using 12.5 mm graded stone aggregates as in floor finishings, finishing the surfaces rough and even to receive screed bed / bedding layer complete all as specified and as directed.

Material and labour, for 75 mm thick Plain Cement Concrete (1:3:6), type C1, using 20 mm graded stone aggregates as in paving / plinth protection, laid in panels, finishing the surfaces even and fair, joints shall be filled with mastic filling in 1:3 (bitumen and sand) complete all as specified and as directed.

Material and labour, non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.06 sq m but not exceeding 0.11 sq m, as in flooring, set and pointed in epoxy grout to match colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour, for coloured Glazed ceramic printed tiles, of size 450 x 300 x 7 mm thick (Grade B-IIA) as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in epoxy grout to match with the colour of tiles, laid over and including provision of backing coat of 10 mm thick rendering in CM 1:3, complete all as specified and directed.

Material and labour, for Vitrified tiles flooring with Light shade 8-10 mm thick (Square / rectangular), tiles, not exceeding 0.36 Sq m, set and jointed in neat cement slurry and pointed in epoxy grout to match with colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour, for Vitrified tile, skirting/dado, light shade with 8-10 mm thick tiles of area of each tile exceeding 0.18 sq m but not exceeding 0.36 sq m, on vertical rates as in skirting, dado, etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including backing coat of 10 mm thick CM 1:3 complete all as specified and as directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, for 18 to 20 mm thick Granite work (of any type), table rubbed and mirror polished), in single piece in steps, jambs, pillars, window-cills, cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe, edges made half round, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:4), complete all as specified and as directed.

Material and labour for, rendering 15 mm thick in cement mortar 1:3 on concrete surfaces, finishing even and smooth including mixing with water proofing compound and applying 1 mm thick Brush Bond, RFX Grey of FOSROC or techno-commercially equivalent as per user’s manufacturer’s instructions, complete all as specified and as directed. Note:- Supply only water proofing compound will be measured and paid for separately under respective items.

Material and labour, for rendering 10 mm thick in Cement mortar 1:6, on brick work/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Material and labour, for rendering 5 mm thick on brick or concrete ceiling surfaces in cement mortar(1:3) and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Preparation of new or previously untreated plastered WALL surfaces of any description not otherwise described and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Preparation of new or previously untreated plastered CEILING surfaces of any description not otherwise described and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Material and labour for, Preparation of old plastered and applying one coat of oil bound distemper on wall surfaces complete all as specified and as directed.

Material and labour for, Preparation of old plastered and applying one coat of oil bound distemper on ceiling surfaces complete all as specified and as directed.

Complete removal of existing treatment and preparing the surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1 mm thick wall care putty complete all as specified and directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Preparing of old wall concrete surfaces, and providing material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gram/litre and UV Resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 complete all as specified and as directed.

Preparation of old wooden surfaces exceeding 10 cm in width or girth, applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old steel surfaces exceeding 10 cm in width or girth, applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new wooden surfaces exceeding 10 cm in width or girth, applying two coats of synthetic enamel paint over a coat of red oxide pink primer complete all as specified and as directed.

Grinding and polishing to existing terrazzo/ kota stone flooring, complete all as specified and as directed.

Supply and fix in repairs, Corner glass shelf (medium) 225mmx225mm with chromium plated bracket superior quality complete Make : Cera, Cat Part No F5005102 or techno and commercial equivalent in other makes specified, complete all as specified and as directed.

Supply and fix in repairs, Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long Make : Jaquar, Cat Part No ACN-CHR-1171N or equivalent in other makes specified complete all as specified and as directed.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips etc. and removing glass / debris outside MD land, complete all as specified and as directed.

Supply and fix Plain Sheet glass 4 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane all as specified and as directed.

Supply and fix Figured glass, 4 mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5 sq m in each pane all as specified and as directed.

Supply and fix, stainless steel wire cloth 0.36 mm nominal dia of wire, and of average width of aperture 1.4 mm, fixed with stainless steel wire staples / wooden beading complete all as specified and as directed.

Supply and fix in repairs stainless steel wire cloth 0.36 mm nominal dia of wire, and of average width of aperture 1.4 mm, fixed with stainless steel wire staples / wooden beading complete all as specified and as directed.

Taking down unserviceable GI tubing, supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Taking up or down 20 mm dia, GI tubing and connections, cleaning, re-fixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), after cleaning and application of bituminous paint in concealed portion of tubing, including cutting and threading pipe and provision of additional fittings such as sockets, tee, elbows, unions, (if required) complete all as specified and as directed. Notes: i) Serviceable Taps, valves in any shall be removed before taking down pipe and same shall be re-fixed while providing new pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, all as specified and as directed.

Supply and fix in repairs, 32 mm dia, PVC waste pipe of length not less than 800 mm, complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 110 mm dia, type B (Conforming to IS 13592), single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 75 mm dia, type B (Conforming to IS 13592), single socketed in any length with rubber ring joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed. Notes for Sl Item Nos 70 & 71 : Provn of necessary scaffolding for replacing defective pipes shall deemed to be included in quoted rates, and nothing extra will be admissible in this regards.

Supply and fix in repairs, PVC (SWR) bends any radius 75 mm dia with access door, fixed in pipes, complete all as specified and as directed.

Supply and fix in repairs, PVC (SWR) bends any radius 110 mm dia with access door, fixed in pipes, complete all as specified and as directed.

Supply and fix in repairs, PVC (SWR) branch piece single T equal or unequal 75mm dia with access door, including taking down old branches all as specified and as directed.

Supply and fix in repairs, PVC (SWR) branch piece single T equal or unequal 110mm dia with access door, including taking down old branches all as specified and as directed.

Dismantling of unserviceable floor trap, supply and fix PVC(SWR) floor trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Dismantling of unserviceable multi floor trap, supply and fix PVC(SWR) multi floor trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Supply and fix, PVC connecting pipe 600 mm long 15 mm dia both ends having brass coupling nut and PVC washer after taking down old connecting pipe complete all as specified and as directed.

Demolition of old closet removing debris outside MD land, providing material and labour for, Vitreous china, white colour, water closet pan (pedestal pattern), with PP soft seat cover, hinges, other fixing accessories set (excluding flushing cistern and flush pipe), UPVC (SWR), 'P' or 'S' trap, and connecting to drain (or outgoing pipe), flush pipe, anti syphonic pipes, Make : Cat Part No S1050101 of Cera or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with UPVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, including removing debris outside MD land. Make : Cera, Cat No S3010102 of CALINA make or techno commercially equivalent in other makes specified complete all as specified and directed.

Supply and fix in repairs, PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including jointing with new PVC long / short flush bend and making good to the disturbed surfaces complete all as per Model No: CIENA PREMIUM Cat Part No B1010102 of CERA Make or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs Health faucet, with 8 mm dia, 1.2 m long, flexible tube in chrome finish, wall hook with NRV (back flow preventer), all as per Cat Part No ALD-577 of Jaquar or techno commercial equivalent in other makes complete all as specified and directed.

Supply and fix in repairs, Bib taps 15 mm dia, fancy type, chromium plated with CP flange all as per Cat No. HT F3001151 of Cera or equivalent in other makes specified complete all as specified and as directed.

Supply and fix, in repairs, two way, bib taps, fancy type, 15 mm dia, cast copper alloy, chromium plated, with CP flange, screwed for iron pipe or for brass ferrule, all as per Cat No.HT F3001163 of Cera or equivalent in other makes specified complete, all as specified and as directed.

Supply and fix in repairs, Pillar taps, 15 mm dia, fancy type, chromium plated with CP flange, long shank all as per Cat No. F3002101 of Cera or equivalent in other makes specified here-in-after, complete all as specified and as directed.

Supply and fix in repairs, Angular cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete all as specified and as directed. MAKE:- Cat No. HT F3001201 of CERA or techno-commercially equivalent model in any one of the make as mentioned in list of makes here-in-after.

Supply and fix in repairs, Stop valves (concealed), fancy type with CP wall flanges, chromium plated, cast copper alloy with long shank and exposed part kit with fittings sleeve, operating lever concealed part screwed both ends for iron pipe or for unions, including making good the disturbed portion matching with adjacent surfaces, complete all as specified and as directed.

Supply and fix in repairs, Chromium Plated overhead shower rose of size 125 mm with swivel joints, over head shower arm of 230 mm long with wall flange, complete all as specified and as directed. Make : Cera Cat Part No F7020305 & F7040103 or techno and commercial equivalent in other makes specified after taking down old shower rose complete all as specified and as directed.

Supply and fix in repairs, Chromium plated, Wall mixer with bend pipe for overhead shower, built-in non return valve with CP wall flanges, as per Cera Cat Part No QT F2006402 or techno and commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 20 mm bore with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.

Supply and fix in repairs, Vitreous china snow white, wash hand basin of size 550 mm x 400 mm all as per Cat No. No. S2040103 of Cera or techno and commercial equivalent makes specified including supply and fixing 32 mm dia, PVC corrugated / flexible waste pipe, 800 mm long and with PTMT waste coupling of 32 mm dia (minimum weight 45 grams), all as specified and as directed.

Supply and fix in repairs, single tube towel rail, brass chromium plated, 600 mm long fixed with chromium plated screws and PVC cleats, complete all as specified and as directed. Make : CERA, Model No F5003103 or techno and commercial equivalent complete all as specified and as directed.

Supply and fix, PVC mirror cabinet of size 330 mm x 430 mm all as per Make: Prayag (Cat Part No 551) or techno and commercial equivalent in other makes specified, complete after taking down old mirror cabinet all as specified and directed.

Taking down old sinks and Supply and fixing Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc. complete all as specified and directed.

Taking down unserviceable plate rack, supply and fix new Stainless steel plate rack of 0.63mm thick sheet, size 600mm x 750mm and of weight not less than 4.5kg each complete all as specified and directed. Make: Blue star, Model No. SSKPR-311.or techno-commercially equivalent make of NIRALI / ANJALI / JAYNA / DIAMOND.

Disconnecting existing PVC water tank of capacity exceeding 300 litres and not exceeding 1000 litres fixed on roof by setting aside (or lowering, if required) for cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and hoisting / refixing / reconnecting in same / new location including writing date of cleaning on each tank with white paint, height / size of letters / figures not less than 10cm in height, complete all as specified and directed.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Dismantling of water tanks of 750 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 750 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Kaveri Enterprise

GURU ENTERPRISES

Moulya Builders

Power and Telecom Systems

Solar Electricals and Electronics

Meghana and Gowda Enterprises

K R Koteswara Rao