Road Safety and road Furniture works on Kalli Neemsar Panhanagar to Bilraya marg to Naimishranya marg Bypass

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface P/L hot applied thermoplastic compund 2.5 mm thick including reflectionsing glass beads @ 250gms per sqm area, thickness of 2.5mm is exclusive of suraface applied glass beads as per IRC:35 the finished surface to be level, uniform and free from streak and holes. (Including Zebra Crossing and Repeated bar)

Road Delinator Providing and fixing of Standard Metal Delineator as per IRC 70-2019 consisting of minimum retro reflective unit exposed area of 330 square cm in white color, full cube comer micro prismatic non-metallic retro reflective sheeting on each side conforming with IRC 67 2012 and meeting the coefficient of retro reflection values as per ASTM D 4950 Type XI table specification. The delineator shall be painted with powder coat of minimum 40 microns thickness, on top of which retro reflective sheeting shall be pasted on both sides. The structure shall be manufactured in roll forming process and shall have height not less than 800 mm above the ground, width not less than 100 mm and shall extend not more than 300mm below the ground while being installed The front and back faces of the delineator should be curved with a radius of not more than 200 mm and with della angle (or central angle of curve) tying between 20 degree and 30 degree, to increase the visibility of the delineator for vehicles moving in continuous curves. The delineator shall have grooves across the length to make the refective sheels vandal-proof). The retro reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67.2012 & proof of the same in form of govemment report shall be uploaded which quoting tender. Il somehow tender pre qualification condition do not ask for government report then the report shall be submitted to engineer-in-charge before finalization of bill. The delineator is meant for application on gaps in median, traffic islands, dangerous bends. roundabouts, narrow bridges etc. or as desired by site engineer.

Supply, fixing & eraction of built up Cantilever Structure 6 m span comprising of one vertical posts of 6.00 M height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal Truss shall comprise of 50 mm dia heavy class M.S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm MS plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 90x90M of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick Lean Concrete in 1:4:8 cement coarse sand and 40 mm gauge stone ballast. RCC withand 1:2:4 cement coarse sand and 20 mm stone grit including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete. Installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67 2010 complete in all respect The Rates shall include cost of design fabrication, supply, transportation, Local shifting Erection of Signage structure using crane, inclusive of all taxes royalty, VAT etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in-charge.

Providing & fixing of reflective signs with a corrosion resistant 4mm thick aluminium composite panel face to be fully covered with High intensity prismatic sheeting type IV as per IRC-67:2010 retro reflective sheeting with MS angle frame of 35x3. For Cantilevr

Retro-reflactrorised Traffic sign as per IRC67-2012 Providing and fixing of retro reflectroised cautaionary mandatory and informatory sign as per IRC 67-2012 made of High intensity grade sheeting vide clouse 801.3 friced over aluminium sheeting type IV 1.5 mm thick supported on miled steel angle irone post 75mmx75mmx6mm firmly fixed to the ground by means of properly designed foundation with M-150 grade cemnent concreat 45cmx45cmx60cm below ground level as per approved drowing. the retro reflective sheeting tested for 3 years outdor wethering test in indian conditions as per IRC 67:2012 & proof of the same in form of goverment report shall be uploaded while quoting tender. Morth 801 (8.4) iv) 90 cm equilateral tringle with diffinitation plate size (20cm X 60cm). ii) 60 cm equilateral tringle with diffinitation plate (20cm X 60cm)

Reflective Raised Pavement Markers (road Studs/Cat Eye) Supply and fixing of reflective raised pavment marker with its body durface made of tough ASA (Acylic styrene Acrylonitrite) or HIPS (Hi- impect Polystyrene) or acrylonitrile butadies styrenc (ABS) The marker shall supported a lod of 13335 kg tested in accordance with ASTMD 4280 and its reflective panels shall consist of numbers of lenses containing single or dual prismatic cubes of providing total internal reflection of the lights entring the lens face. retro refletive surface shall perferably be 35t 5 degree to base and area of each retor reflecting surface shall not be less than 13.0 sqcm road studs shall be legibly marker with name trade mark or other means of identification of the manufacturer. mimensions of road studs should not be less than 100 mm x 100 mm x10mm. RPM (With shank)as per ASTM MoRTH 804 (8.35)Suggestive. (with Shank)