GE U(N) 26 2022 23 SPECIAL REPAIR TO BUILDING NO NP 74 NP 75 OFFICE AND SINGLE LIVING OF ORs INCLUDING CERTAIN MINOR WORKS IN VARIOUS LOCATIONS UNDER GE (N) UDHAMPUR

Amount

M&L for dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed by the Engr-in-charge.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet profile having min ht @ spacing n.exc 200 mm 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based crimp ridge 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engr-in-charge.

S&F Pre-painted galvalume aluminum zinc coating GI based crimp ridge 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engr-in-charge.

M &L for Plain Cement Concrete Type C1 1:3:6 (using 12.5 mm graded aggregate) as in roof padding / leveling coarse in between wall and roof sheet, or chamfered on edges finished even and smooth with using extra cement and water proofing compound. ( Water proofing compound shall be measured and paid sepratly ) complete all as specified and directed by the Engr-in-charge.

M&L for demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed by the Engr-in-charge.

M&L for 50 mm thick Cement concrete type C-2 , 1:3:6 using 40mm graded aggrigate Finishing surfaces of concrete topping even and fair finishes (without using extra cement) as in plinth protection all as specified and directed by Engr-in- Charge.

M&L for 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base to receive floor finishes complete all as specified and directed by the Engr-in-charge.

M&L for demollition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed by the Engr-in-charge.

S&F Machine cut kota stone slab flooring 18-20mm thick laid over & including 20 mm th cement screed in CM 1:4 base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by the Engr-in-charge.

All as per SI no 10 above but as in skirting/dado etc. including 10 mm thick rendering complete all as specified and directed by the Engr-in-charge.

M&L for 15-16 mm thick white or any approval colour marble slab in flooring over cement screed base laid and jointed with white cement slurry mixed to match the shade of the slab including rubbing and polishing incl 20 mm thick screed bed complete all as specified and directed by the Engr-in-charge.

S&F chequered cement concrete tiles 30 cm by 30 cm by 25 mm thick, with grey cement and pigments, set, jointed over 15 mm thick screed bed in CM 1:4, and pointed in neat cement slurry in floors complete all as specified and directed by the Engr-in-charge.

M&L for providing precast cement concrete kerb stone type B1 1:2:4 (20mm gradded aggregate) of vany section as indicated with plain fair faces including champers, weathering,throating and setting in cement mortar 1:4 complete all as specified and directed by the Engr-in-charge.

M&L for preparation of new surface of any description, not otherwise described, over 10 cm width or girth applying two coat of synthetic enamel paint over one coat of cement primer any shade ascomplete all as specified and directed by the Engr-in-charge.

M&L for demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and recast concrete articlescomplete all as specified and directed by the Engr-in-charge.

M&L for half brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and directed by the Engr-in-charge.

M&L for brick work with sub class 'B' straight or curved on plan exc. 6 m mean radiusbuilt in CM 1:4 complete all as specified and directed by Engr-in-charge.

M&L for taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by the Engr-in-charge.

M&L for rendering 15 mm thick in cement mortor 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by the Engr-in-charge.

M&L for rendering 10 mm thick in cement mortor 1:6 other than fair faces of brick work or concrete surfaces complete all as specified and directed by the Engr-in-charge.

Supply only integral water proofing compound complete all as specified and directed by the Engr-in-charge.

M&L for two coat of cement base paint over a coat of alkali resistant primer including 1mm thick exterior wall care putty including preparation of newly plastered of wall complete all as specified and directed by the Engr-in-charge.

M&L for two coats of oil bound distember over a coat of primer over two coats of approved wall care putty 1mm thick over and including preparation of new plastered surfaces of wall complete all as specified and directed by the Engr-in-charge.

M&L for complete removal of existing treatment, preparation of plastered surfaces of wall and applying two coats of cement base paint over one coat of cement primer including 1 mm thick exterior wall care putty ( to be applied in two coats) all as specified. Note: Putty surface shall be rubbed with emery paper to foRm even and smooth surface.

M&L for complete removal of existing treatment, preparation of surfaces of old wall surfaces and applying two coats of oil bound distember over one 1 mm thick wall care putty complete all as specified and directed by the Engr-in-charge.

M&L for taking down Chowkats or frames exc 1.5 Sqm but not exceeding 4 Sq.M each with shutters (Without taking off shutters from the frames) complete all as specified and directed by the Engr-in-charge.

M&L for taking down Chowkats or frames not exc 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed by the Engr-in-charge.

M&L for taking down shutters of any descp exc 1 sqm but n.exc 2 sqm complete all as specified and directed by the Engr-in-charge.

M&L for 35 mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and directed by the Engr-in-charge.

M&L for 35 mm Glazed and skeleton shutters, 2nd class H.W open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkatscomplete all as specified and directed by the Engr-in-charge.

S&F roof trusses (framed) , trussed , purline, cross gantries and fastening and heavy brakets framing (Beam, tee, angle,channel or flat section ) including distance pieces complete all as specified and directed by the Engr-in-charge.

M&L for preparation of new steel and iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint (any colour) over preprimed surfaces, complete all as specified and as directed by Engr-in-Charge.

M&L for preparation of old steel and iron surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint (any colour) over preprimed surfaces, complete all as specified and as directed by Engr-in-Charge.

S&F 300 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on olt plate and two on staple plate and fixed complete all as specified and directed by the Engr-in-charge.

S&F 150 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by the Engr-in-charge.

S&F 150 mm extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by the Engr-in-charge.

S&F 100 mm butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed by the Engr-in-charge.

S&F small fittings 1st class hard wood such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed by the Engr-in-charge.

M&L for two coat of enamel paint on wooden surfaces over a coal of primer including preparation of new Surfaces of any description, not otherwise descri-bed, over 10cm width or girth complete all as specified and directed by the Engr-in-charge.

M&L for two coat of enamel paint on wooden surfaces over a coal of primer incl preparation of old Surfaces of any description, not otherwise descri-bed, over 10cm width or girth complete all as specified and directed by the Engr-in-charge.

M&L for dismantling ceiling boards,fibre pulb insulation etc or insulation boards/ slabs/ blanket ,any thickness, including cover and MS Tee grid,complete all as specified and directed by the Engr-in-charge.

S&F false ceiling boards of Fibre Cement Designer tile white painted (High Pressure Steam Cured) of 4mm thickness (as per IS-14862) of size 1220mmx1220mm/ 1195mmX595mm/ 1220mmX610mm and any one of the design (occeanic , lake & hill, cascade or electra) fixed with screws over existing metal grid including required cutting/making opening for services like fixed over existing grid inluding necessary scaffolding etc and refixed all exesting electric wiring and fixture all complete at all heights as per direction of Engr-in-charge.

M&L for for Plain cement concrete 1:2:4, type B1, using 20mm graded stone aggregate as in coping/benching, bed plate including necessary form work complete all as specified and directed by the Engr-in-charge.

M&L for kota stone slab window cills/steps(single piece) incl bull nosing rounding edges directed colour, 18-20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with grey cement shade of slab including grinding and polishing, over 10mm thick rendering in CM 1 :3 complete all as specified and directed by the Engr-in-charge.

M&L for providing and fixing power coated aluminium (minimum thickness of power coating 50 micron) for shutters of doors,windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprane gasket required (fitting shall be paid for seprately) with extruded built up standard tubular section /appropriate Z section and other section of approved make conforming to IS:733 and IS:1285 fixing with dash fastner of required dia and size, including necessary filling up the gaps at junctions i.e. top, bottom and sides with required EPDM rubber/neoprene gasket etc.Aluminiums section shall be smooth ,rust free,straight mitred and jointed mechanical wherever required including cleat angle, aluminium snack beedingfor glazing/ panneling , CP brass / stainless steel screws all as complete as per architectural drawing complete all as specified and directed by the Engr-in-charge.

S&F power coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified (minimum thicknessof powr coating 50 micron) complete all as specified and directed by the Engr-in-charge.

S&F glazing with 5mm thick frosted/tinted sheet glass exc 0.50 sqm in each panel fixed to aluminium section of doors, windows and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified and directed by the Engr-in-charge.

S&F anodised aluminium grill ( anodised transparent or dyed to required shade according to IS: 1868 with aminium anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requiremnet and direction of Engineer-in-charge.

S&F stainless steel mosquito proof wire cloth of stainless 0.36mm dia and 1.4mm aperture fixed with aluminium flat/channel and screws all as specified as directed by Engr-In-Charge.

M&L for machine pressed precast conrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 grade laid over and inclusive 30 mm thick sand filling complete all as specified and directed by Engr-in-Charge

M&L for dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge

M&L for non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed with spacer and laid with epoxy grout in neat cement slurry and pointed to match including 10 mm screed bed 1:4 cement mortar complete all as specified and directed by the Engr-in-charge.

M&L for glazed ceramic tiles 300x450x7 mm to 8mm thick in vertical surfaces such as skirting, dadao and risers to steps over 10 mm thick in CM(1:3) incl taking down from existing surfaces complete all as specified and directed complete all as specified and directed by Engr-in-Charge

M&L for taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal complete all as specified and directed by the Engr-in-charge.

M&L for taking up or down 25 mm bore steel tubing and connections, including cleaning for Refixing or removal complete all as specified and directed by the Engr-in-charge.

S&F 15 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls complete all as specified and directed by the Engr-in-charge.

S&F 25 mm bore Galvanized Steel tubes, medium grade with all fittings for water supply pipes etc., laid in trenches/fixed on walls complete all as specified and directed by the Engr-in-charge.

M&L for dismantling water tanks of exceeding 250 & not exceeding 500 ltrs and removing to store, complete all as specified and directed by the Engr-in-charge.

S&F in repairs for 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by the Engr-in-charge.

S&F 20 mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed in position complete all as specified and directed by the Engr-in-charge.

S&F GI Unions,20mm brass to connect iron to polyethylene and fixed complete all as specified and directed by the Engr-in-charge.

S&F in repair vitreous China Squatting pan "Orissa pattern" long pan, size 580 x 440 mm white ,with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc., including trap set in and including lime concrete complete all as specified and directed by the Engr-in-charge.

S&F vitreous china wash down water closet (pedestal pattern) white complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, fixed in repair, complete all as specified and as directed.

S&F plastic water closet seat cover, closet pattern with flat bottom and cover and incl mild steel chromium plated or aluminum hinges device complete fixed in repairs , all as specified.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 300mm complete all as specified and directed.

S&F in repair PVC valveless , syphonic action type, Flushing cistern low level, white , with inlet, ball valve, float and handle including brackets,10 ltrs capacityi ncl suitable pvc flushing bend complete all as specified and directed.

S&F in repairs Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F angle cock concealed valve cast cpper alloy fancy type 15 mm complete all as specified and directed.

S&F in repair Bib tap cast copper alloy fancy type suitable for15 mm dia pipes complete all as specified and directed.

S&F in repair Corner glass shelf complete all as specified and directed by the Engr-in-charge.

S&F CP towel rail 600 mm complete all as directed complete all as specified and directed.

S&F CP towel ring square complete all as specified and directed by the Engr-in-charge.

S&F 125x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

S&F 105x 60 mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed by the Engr-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wall nut colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete, all as specified and directed by Engr in Charge.

S&F Factory Made Solid PVC Moulded Door Shutter wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the ront face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing but 2mm thick Moulded Prelam PVC Sheet on the front ace & 2mm Plain colour PVC Sheet on back face ® complete all as specified and directed.

S&F in reapirs 25 mm dia MS powder coated antique type curtain rods with bracket fixed to wall with suitable screws and onion type end brackets all as per approved design/ colour/ pattern fixed as directed in Engr-in-Charge.

S&F looking mirror of size 450 x 600 using 5 mm thick mirror edges rounded fixed with clips all as specified incuding teak wood/pvc frame of size 25 x 25 mm decorativ and water proof including malimine polishing complete all as specified and directed by the Engr-in-charge.

S&F viterous china wash basin,white colour flat back size 550X440 mm incl waste coupling cp 32 mm dia chin and plug and porcelain stopper and CI brackets of iron 65x65x6mm embedded in pcc block with pcc 1:2:4 type B-1 and PVC waste pipe 32 mm dia & CP grating with holes with full pedestal of china ware,including PVC connection 15mm size with PTMT nuts of length 600mm and pillar mixer 'Hot and cold',fancy type,cast copper alloy, with capstan heads,choRmium plated,screwed down,high pressure,with or without lettered with long screwed shanks and fly nuts, screwed for iron pipe of bore 15mm,fixed in complete all as specified and as directed by Engr-in-Charge.

M&L for taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends swan necks, etc, including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fitting and accessories) complete all as specified and directed by the Engr-in-charge.

S&F 75 mm bore PVC (SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by the Engr-in-charge.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps, complete all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) bends 75 mm bore any radius with oveal & acces door complete all as specified and directed.

S&F PVC (SWR) bends any radius in 110 mm dia complete all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) floor trap plain/multi with grating incl. jointing with solvent cement (75 mm bore) complete all as specified and directed by the Engr-in-charge.

S&F in repairs Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe & waste pipe) complete all as specified and directed by the Engr-in-charge.

S&F false ceiling with everest fiber cement designer tile lovery/white paint (high pressure steam cured) of 4mm thickness (as per IS-14862) of size 595x595mm and any one of the designed (oceanic, lake & hill cascade or electra) in true horizontal level, suspended on interlocking power coated certa black pattern metal grid of hot dipped galvanised steel section (galvanised @ 12gms both side inclusive) consisting of main T runner with suitably spaced joint to get required length and 15x32 mm made3 of 0.30mm sheet6 spaced between main T @600mm C/C from a ridge of 600x600mm and wall angle of size 15x20mm made of 0.30mm thick sheet and laying false ceiling tile in the rid including required cutting/making opening for service like diffuser grills light suspended from ceiling using GI softy cleats fixed to existing rafters purlin etc. with dash fastener GI adjustable rod of 3mm dia with galvanised butterfly level clips spaced at 1200mm c/c along main T bottom exposed width of 15mm of all T-sections shall be entre black pre-painted with polyester paint and having a load bearing capacity of 12Kg/sqm and re-fixed all existing electric wiring and fixture all complete all as specified and directed by the Engr-in-charge.

M&L for taking down carefully the existing Copper/Aluminium point wiring of any size and type by disconnecting from the either teRminals complete with switches, sockets, ceiling rose, regulators, bell etc by unscrewing and removing materials to store for keeping in safe custody for re-use or for taking credit and making good to disturb surface of walls, floors etc., complete all as specified and directed by Engr -in- charge. Note : (i) Old dismanteled wiring and accessories (other than reuse) will be contractors property and credit will be charged against schedule of credit.

M&L for point wiring with PVC insulated unsheathed, FRLS 1100 volts grade stranded copper conductor cable single core 1.5 Sqmm for one light / fan point controlled by one way switch, and wire to be drawn in and including rigid pvc concealed conduit of dia not less tham 20mmof 2mm wall thickness complete with all accessories including GI anealed metal box 1.2 mm thick switch board of suitable size be fixed flush wall , with 3 mm thick ebonite sheet cover and necessary screws, cap washers etc. or to be fixed on wall respectively as directed by EIC and providing earth continuity wire using PVC insulated, un sheathed single core stranded copper conductor FRLS cable of size 1.5 Sqmm.

All as per item No. 91 above but for one 3 pin 5 Amps socket outlet on independent board.

All as per item No. 91 above but wire size 2x2.5 Sqmm and and providing earth continuity wire using PVC insulated, unsheathed single core stranded copper conductor FRLS cable of size 2.5 Sqmm. to controlled the 3 pin 5 / 15 Amps socket outlet on independent board.

All as per srl item No 91 above but for one 3 pin socket outlet 15 Amp independent with cable of size 4 Sqmm for piont wiring and 4 sqmm as in contineous earth wire.

M&L For point wiring with 1.5 Sq. mm copper conductor, single core, PVC sheathed, cable, to controle one 3 pin socket outlet, 5 Amps on the same board with other switch.

S&F Switch Piano, flush type, One way, single pole, 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Two in one, 3 Pin, 5 Amps, flush type socket outlet complete all as directed by Engineer- in - Charge.

S&F Switch Piano, flush type, One way, single pole, 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Switch socket combination 5 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Switch socket combination 15 Amps, suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Two in one, 3 Pin, 5/15 Amps, flush type socket outlet suitable for 240 V, 50 Hz, AC supply complete all as directed by Engineer- in - Charge.

S&F Ceiling rose, 3 teRminal, PVC / polycarbonet, isolated body complete all as directed by Engineer - in - Charge.

S&F Stepped type, electronic fan regulator, flush type on the existing phenolic laminated sheet etc. as required complete all as directed by Engineer- in - Charge.

S&F Modular switch 1 way 6A, 1 module single pole, all as specified and directed by Engineer- in - Charge.

S&F Modular socket, 6A - 2/3 pin 2 module complete all as specified and directed by Engineer- in - Charge.

S&F Modular switch 1 way 16A, 1 module single pole , complete all as specified and directed by Engineer- in - Charge.

S&F Modular socket 16A - 2/3 pin 2 module complete all as specified and directed by Engineer- in - Charge.

S&F Modular Fan step regulator, 120W - 2 module, 240Volt flush type suitable for 1200/1400mm sweep ceiling fan, ISI marked complete all as specified and directed by Engineer- in - Charge.

S&F in replacement Slim linear LED lighting fixture 20 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete all as per the direction of Engr-in-Charge.

S&F in replacement Slim linear LED lighting fixture 10W watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection from ceiling rose to fittings including testing complete all as per the direction of Engr-in-Charge.

S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by the Engr-in-charge.

M & L for sub main wiring with two run single core 6 Sqmm FR-LS copper conductor cable PVC insulated, unsheathed, 1100 V including 25 mm dia PVC concealed conduit medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 Sqmm single core PVC FR-LS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board / distribution board and testing on completion etc complete all as specified and directed by the Engr-in-charge. Note: Two runs of 6sqmm and one run of 6 sqmm cable and one run of PVC conduit/ casing capping shall be measured as one Rm

S&F 3 mm thick plastic laminated ebonite sheet cover of size 400mmx300mm including cutting /finishing or making hole for mounting of switches, sockets, regulators etc complete all as specified and directed by the Engr-in-charge.

S&F steel terminal boxes of size 400mmx300mm including cutting /finishing or making hole etc complete all as specified and directed by the Engr-in-charge.

S&F Slim linear LED lighting fixture 18 watt LED batten, with full base of extruded aluminium section acting as a heat sink with closed back, isolated driver, complete making all connection using 1.5 sqmm copper conductor multistrandard PVC insulated 2 core flexible cable with flexible PVC pipe from ceiling rose to fittings complete including taking down old US tube light fitting 36/40W and taken in schedule of credit all as per the direction of Engr-in-Charge. Make model of Havells cat No LHEXCEP7UN1W020 or equilent to CG/ Phillips

S&F bulding security (street) light fitting 35 watt, new generation energy saving & environmental friendly long life versatile pressure die cost aluminium IP 66 with acylic, powder coated, pressure die cast aluminium compact high power LED street light with heat resistant toughed glass, corrosion resistant, isolated driver, including provision of GI tubing bracket of suitable size and fixed on wall including clamps, nut, bolts and washer for fixing of security (street) light completet as per direction of Engr-in-Charge. Make:Havells Cat No : ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC, Wipro

S&F ceiling fan of 1200mm sweep white in color of BEE five star rating including all electric connection and testing complete all as specified and as directed by the Engr-in-Charge.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as directed by Engr-in-Charge

M&L for taking down fan/Exhaust fan, ceiling cable end, dismantling blades and kept in safe custody for repairing/servising complete all as specified and directed by the Engr-in-charge.

M&L for repair of ceiling fan 1200mm sweep/ Exhaust fan of any make obtained from above item, oiling, greasing after cleaning slot, over hauling & replacement of defective split pin nut bolts washer etc including spray painting with enammeled paint with the help of spray gun and marking of MES No with black enammeled paint all as specified and directed by Engr-in-charge.

M&L for hanging /fixing only ceiling/Exhaust fan and connecting up including provision of stranded 3core flexible 1.0sqmm copper conductor cable from ceiling rose or connector to fan all as specified and directed by Engr-in-charge.

M&L for for earthing complete with GI earth plate electrode 600mmx600mmx6mm thick burried in ground vertically to a depth not less than 2.25meters below ground level with top edge of the earth plate at a depth not lesss than 1.5 meter below NoRmal ground level, earth plate surrounded 15cm thick layers of common salt and charcoal dust starting from ground below 15 cm of earth plate and up to 15 cm above the same. GI plate connected with galvanised earth lead wire 4.0mm dia by means of GI nuts, bolts and washers of galvanised iron or steel all as shown in electrical plate no.5 connecting to earth test point all as specified or indicated including testing on complition with following:- (a) Test point GI wire 4mm dia . (b) GI pipe light grade 20mm dia from top of the earth electrode up to MS funnel with wire mesh embeded in floor of PCC earth pit. (GI Funnel should properly tightned on GI watering pipe and embeded in PCC floor of earth pit with open top suitable for watering of earth pits) (c) PCC earth pit 30x30x30cm constructed in PCC 1:2:4 type B1 exposed surfaces smoothly finished with 15mm thick cement mortar 1:6 plaster including RCC pit cover 25mm thick with 2 Nos MS handles of 12mm dia suitable for carrying of pit cover. (d) Angle iron frame made of 40x40x4 mm angle iron for 30x30 mm PCC pit for holding the pit cover.

S&F sheet metal enclosure single door single pole and neutral 240 Volts for DB's when MCBs to be used 2 way with 200 amp rated bus bar with IP-43 protection complete all as specified and directed by the Engr-in-charge.

S&F in replacement single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 8 way complete all as specified and directed by the Engr-in-charge.

S&F in replacement single pole and neutral sheet steel powder coated Distribution board for MCBs fitted with bus bar , Neutral link ,Earth Bar and Din rail suitable for use on 240 V, 50 Hz supply double door SP&N DB system 12 way complete all as specified and directed by the Engr-in-charge.

S&F, connection and testing MCB SPN 32-63 Amp, 240 Volts, 'C' series, breaking capacity 10 KA of rating 32-63Amps complete all as specified and directed by the Engr-in-charge.

S&F 'C' series SPN MCB 40 to 63 Amp Amps 240V ,50Hz,10kA lighting and other domestic loads incl all teRmnials, fitting etc complete all as specified and directed by the Engr-in-charge.

S&F connection and testing MCB SP 6-32 Amps 'B' Curve complete all as specified and directed by the Engr-in-charge.

S&F Plug and socket DBs, single pole and neutral enclosure with a two pin earth plug and socket with one single DP20 Amps, 240 volts MCB complete all as specified and directed by the Engr-in-charge.

S&F in repair sheet metal enclosure VTPN 08 way 415 volt 250 Amp rated bus bar double door type with suitable for mounting MCCB for incomer and MCBs for outing without MCCB and MCB IP-43 protection fixed in repair complete all as directed by Engr-in-Charge.

S&F MCCB 4 pole, 415 volt, Adjustable type 200 Amp with breaking capacity 25 KA complete all as specified and directed by the Engr-in-charge.

Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire aRmored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 sq mm 3.5 core in trenches/floor/pole/GI pipe complete including cuttingof bituminous road/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and directed by the Engr-in-charge.

SupplyIing, laying fixing and testing in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire aRmored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 2 core in trenches/floor/pole/GI pipe complete including cutting/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and directed by the Engr-in-charge.

Supply and lay in replacement XLPE Insulated screened PVC bedded, galvanized steel strip or wire aRmored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core in trenches/floor/pole/GI pipe complete including cuttingof bituminous road/chasing to any surface and making good to the disturbed surface to match the existing complete all as specified and directed by the Engr-in-charge.

M&L for excavation in trenches in any type of soil n exc 1.5m deep and not exc 1.5m wide for laying of under ground cable, electric pole and getting out complete all as specified and directed by the Engr-in-charge.

M&L for returning filling in including spreading leveling watering and well ramming 25cm in thickness in any type of soil complete all as specified and directed by the Engr-in-charge.

M&L for removing excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed by the Engr-in-charge.

M&L for dry sand cushioning to under ground cables provided with a layer of sand 8 cm deep before laying the cable, 15 cm depth after laying cable & stretching the cable complete all as specified and directed by the Engr-in-charge.

Supply and lay brick class ‘B’ covering as mechanical protection to cable with well burnt complete all as specified and directed by the Engr-in-charge.

M&L for GI tubing light grade with all fitting and fixed in wall and floor or fixed to pole of size 40mm dia complete all as specified and directed by the Engr-in-charge.

M&L for bore hole for passing of cable through/insection of 40/80 mm dia GI pipe under PCC/Road/Taxy Track/ Runway/ Hardstanding not less than 1200 mm deep complete all as specified and directed by the Engr-in-charge. Note: (i) Cost of equipments, tools and plants, material required for boaring shell be deemed to be included in unit quoted rate above. (ii) Cost of GI pipe 50/80 mm dia shell be deemed to be included in unit quoted rate above. (iii) Cost of air compressor for boaring shell be deemed to be included in unit quoted rate above.

M/S JANDIAL ENTERPRISES

M/S GURU DEV BUILDERS

KUMAR CONSTRUCTION CO

MADAN LAL SHARMA AND SONS

SHIVAE CONSTRUCTION

HANS RAJ SHARMA

TULSI RAINA AND SONS

KALSOTRA CONSTRUCTION CO