Construction of central veterinary hospital at Dambuchan (by way of balance work).

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres. All kinds of soil.

Dumping stone including cost of stones. in Horizontal on level

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for. a). Foundations, footings, bases of columns etc. for mass concrete.

d) Suspended floors, roofs, landings, balconies and access platforms.

e) Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood

Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). second class kail wood.35mm

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors,windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to bemeasured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Plainparticleboardflatpressed,3layerorgradedwoodparticleboardmedium density Grade I, IS : 3087 marked

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 1st Class Kail wood 35 mm thick

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm

Demolishing stone rubble masonry manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge : In cement mortar

Demolishing brick work manually/bymechanical means including stacking of serviceable material and disposal of unserviceable material within 50metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below

Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete,tomatchexistingsurfacei/cdisposalofmulba/rubbishtothenearest municipal dumping ground, all complete as per direction of Engineer-in-Charge For door/ window/ clerestory window

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

15mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Finishing walls with textured exterior paint of required shade : Old work(Two or more coats on existing cement paint surface applied @3.28 ltr/10 sqm.

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

French spirit polishing : Two or more coats on new works including a coat of wood filler.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285,fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): For fixed portion. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately): For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Prelaminated particle board with decorative lamination on both sides.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm

Chequerred precast cement concrete tiles 22mm thick in foot path & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbingandcleaningetc. complete, on20mmthickbedof cement mortar 1:4 (1 cement: 4 coarse sand). Dark shade pigment using ordinary cement

Providing and laying 60

mm thick faciory made cement in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately): 12 mm thick

Providing and fixing 100mm Pine wood plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface. 10 mm thick

Providing and fixing 3laye rPP-R(PolypropyleneRandomcopolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply includingall PP-Rplain&brass threadedpolypropylene randomfittingsi/cfixingthepipewithclampsat1.00mspacing.Thisincludesthe costof cuttingchases andmaking goodthe same including testingof joints completeasperdirectionofEngineerinChajge.(Concealedworkincludingcutting chases and making good the walls etc.,) PN-16 Pipe, 25 mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R(Polypropylene Random copolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-Rplain&brass threadedpolypropylene randomfittingsi/ctrenching.refilling&testingofjointscompleteasperdirection of Engineer in Charge. (External work) PN - 16 Pipe, 32 mm OD (SDR-7.4)

Providing and fixing 3 layer PP-R(Polypropylene Random copolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-Rplain&brass threadedpolypropylene randomfittingsi/ctrenching.refilling&testingofjointscompleteasperdirection of Engineer in Charge. (External work) PN-16 Pipe, 40 mm OD

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape for inner wall fittings . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 25 mmm)

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , tapping with cello tape aluminum sheet 26 gauge cladding with dia . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 32 mmm)

Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , tapping with cello tape aluminum sheet 26 gauge cladding with dia . complete job including carriage 19 mm thick, 50 mm dia (OD) ( PPR 40 mmm)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star , lotus or equivalent having valid ISI liscence including puffing insulation double layer)

Providing and fixing for the material insulation of water storage tank with nitrile tube, taping with cello tape, polythene, rock wool 6 inch per side, wire mesh and aluminium sheet all complete job including carriage 19mm thick nitrile sheet

Providing and fixing heat tape 33Watt on PPR pipes made of denforced or chromelox or equivalent make, as approved by Engineer InCharge , complete Job

Providing and fixing PVC soil waste and vent pipe of required dia including bends, TEE door bend, L bend trap jointed with addisive material ISI marked like prince vector of equivilent brand all complete 100mm.

Providing and fixing PVC soil waste and vent pipe of required dia including bends, TEE door bend, L bend trap jointed with addisive material ISI marked like prince vector of equivilent brand all complete 75 mm.

Providing and fixing wash basin with C.I.brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Surgeon type wash basin of size 660 x 460 mm with a pair of 15 mm C.P. brass pillar taps with elbow including operated levers

c).Stone an average lead of 20kms

Providing & fixing stainless steel Floor trap of self cleansing design with CP Jali complete in all respects. (Make : Supreme / Finolex / Prince)

Providing and fixing CP wall mixer of standard design and approved quality and make as approved by Engineer in charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing gyeser of req. capacity incl. fixing with all fixture complete job.20ltr

Providing and fixing P.V.C.waste pipe for sink or wash basin including P.V.C.waste fittings complete. Semi rigid pipe 32 mm dia

Providing and fixing white vitreous china laboratory sink with C.I. brackets,C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P.brass trap with necessary C.P. brass unions complete includingpainting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200mm

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.

Providing and fixing mirror of superior glass(of approved quality)andofrequired shapeandsizewithplasticmouldedframeofapprovedmakeandshadewith6 mm thick hard board backing : Rectangular shape 453x357mm

c).Stone aggregate an average lead of 15 kms

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade.Two or more coat applied @0.90ltr/10 sqm over an under coat of primer applied@ 0.80 ltr/10 sqm of approved brand and manufacture

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up toany pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specifi

Providing corrugated G.S. sheet roofing including vertical /curved surface fixed withpolymercoatedJorLhooks,boltsandnuts8mmdiametrewithbitumen andG.I. limpetwashers orwithG.I. limpetwashers filledwithwhite lead, includingacoatofapprovedsteel primerandtwocoatsofapprovedpainton overlappingofsheetscomplete(uptoanypitchinhorizontal/verticalorcurved surfaces),excludingthecostofpurlins,raftersandtrussesandincludingcutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m3

Providing and fixing ISI marked flush door shutters conforming to IS:2202(PartI) decorative type, core of block board construction with frame of 1st class hard woodandwellmatchedteak3plyveneeringwithverticalgrainsorcrossbands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/ Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 10 mm depth and 10 mm width

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc.complete : a) 300x16 mm

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC10 as perIS:1868)transparent or dyed to required colour or shade, with necessary screws etc. complete : A) 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC10 as per IS : 1868 ) transparent or dyed to

Earthwork in excavation by manual means in foundation trenches or drains(not exceeding 1.5m in width or 10 sqm on plan), includingdressingof sidesand rammingofbottoms, liftupto1.5m, includinggettingouttheexcavatedsoiland disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

required colour or shade, with necessary screws etc.complete : A) 250x10 mm

Engagement of labour for cutting reinforcement bars and stacking same at proper places and cleaning washrooms and all as directed by engineer in charge. All complete job

b).Sand an average lead of 15 kms

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Carriage of material by MT from source to site of work, incl. loading, unloading complete job.Cement an avg lead 02KM

Point

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. A) 2 x 1.5 Sq.mm+ 1 x 1.5 Sq.mm earth wire

b) 2 x 2.5 Sq.mm + 1 x 2.5 Sq.mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. For inverter.1x 1.5 sq. mm

c) 2x 10 sqmm + 1 x 6 Sq.mm earth wire

d) 4 x 16 Sq.mm + 2 x 6 Sq.mm earth wire

Supplying and fixing following modular type switch/socket on the existing switch box cover including connections etc. as required.a) 5/6 A switch

b) 3 pin 5/6 A socket outlet

c) 15/16 A switch

d) 6 pin 15/16 A socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 2 Nos. 3 pin 5/6 amps modular socket outlet and 2 nos .5/6 amps modular switch, connection etc. as required

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 amps & 15/16 amps. modular socket outlet and 15/16 amps modular switch connection etc. as required.

e) TV antenna socket outlet

f) Bell push

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)a) 6 way (4 + 18) Double door

b) 8 way ( 4+ 24) Double Door

Supply and fixing of following sizes of PVC conduit alongwith accessories in surface/recessed including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supply, installation, testing & commissioning of GI Electrode Earthing with 84 mm dia and 3 meter length, with 40mm x 5mm thick the electrode should be hot-dip galvinised. The GI Electrode shall be pre-filled with Cristaline Conductive Materila (CCM). The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact betwen the electrode and compound should be eco-friendly GI Electrode Earthing should be maintinance free and does not require regular manual addition of water . The earthing pit should be covered with PVC cover.

Providing and fixing scrub up sinks equipped wtih knee and elbow operating faucets with C.I. brackets, C.P.brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trapwith necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required :

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Fabrication ,supplying ,installation testing and commisssioning of following pannel made out of 2mm thick M.S sheet, wall mounted ,vermin & dust proof ,indoor type with lockable type hinged doors,duly painted with provision for fixing of 1 no incomer MCCB . type change over switch including supply and fixing 1 set of Aluminium Bus bar ,and strip for housing MCBs 72 Nos , MF Digital Meter and and other allied accessories as required .(Make as per annexure)

Providing and fixing C.P. brass long nose clinical faucet of approved quality conforming to IS:8931 : 15 mm nominal bore

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 400 A,50KA,FPMCCB

Change over Switch (on Load ) FP 400 Amp

Supplying and fixing of following rating 240/415 Volt's "C" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning (Above to 32 Amp.).SPN 63 Amp

Supplying and fixing of following rating 240/415 Volt's "C" Series miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections, testing and commissioning (Above to 32 Amp.).TPN 63 Amp

Supplying and fixing of 1.1 KV PVC insulated and PVC sheathed XLPE Aluminium Power Cable of following sizes on surface/surface cable tray/0.50 mtr bleow ground level etc. as required including carriage upto site of work. (Make as per annexure enclosed) 70 sqmm 3.5 core-Armoured

LED down lighter 12 watt including cutting of Holes.

LED down lighter 20 watt including cutting of Holes.

Supplying , installation testing and commissioning of LED 2'x 2' recess mounted fixture that delivers atleast 3000 lumens and wattage not more than 36 watt,