Renovation of Administrative Building and Boundary Wall of Jharkhand Rajkeey Mudranalay at Doranda, Ranchi

Amount

Extra for cleaning the old surface by scrapping the entire old white wash or colour wash including cost of scaffolding all complete as per direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing apes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with12.5 mm thick tapered edge Glass Rinforcd gypsum(GRG) board conforming to IS: 095(Part 3) 1996(Boards ith BIS crfitcation marks) moisture resistant board

Providing 6mm thick cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete. E/I.

Providing &Applying high quality acrylic modified resin based texture of Dholpur/Red sand stone patter with anti algae and Uv resistace properties to be aapplied as intermediate fiish in desired pattern @ 43.04 kg/s10 sqm to form film of 1-1.5mm thickess after scrapping and propperly cleaning the surace to remove loose particles from the plaster surface,followed by top coating with premium acrylic smooth exterior paint with silicone additives of required shade by two or more cots @ 1.43 litre/10sqm,complete as the direction of E/I.

Taking down old door and window shutters including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down chaukhats in windows including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and coceletial windows openings, including wedge over all clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 30mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 30mm thick solid core type non-decorative double leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS :2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Dismantlingtile work in floors and roofs laid in cement mortar including stacking material with in 50 metres lead for thickness of tiles 10mm to 25mm including all complete job as per direction of E/I.

providing and laying polished vitrified tiles in floor in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved brand & Manufacturer in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand)jointing wth grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glsazed viterified floor tiles including all complete. Glazed vitrified floor tiles polished finish of (size 600x1200mm)

Providing and laying polished vitrified tiles in floor in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved brand & Manufacturer in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand)jointing wth grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glsazed viterified floor tiles including all complete. Glazed vitrifieid tiles Matt/Antiskid finish (size 600x600mm)

roviding and laying polished vitrified tiles in floor in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved brand & Manufacturer in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand)jointing wth grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., The tiles must be cut with the zero chipping diamond cutter only.Laying of tiles will be done with the notch trowel,plier,wedge,clips of required thickness,leveling system and rubber mallet for placing the tiles gently and easily.Glsazed viterified floor tiles including all complete. Glazed vitrified floor tiles polished finish of (size 600x600mm)

Providing and fixing 18mm thick Gang saw cut mirror polished, pre molded and pre polish machine cut for kitchen platforms, vanity counters windows sills, facias and similar locations of required size approved shade,colour and , texture laid over 20mm thick base cement mortar 1:4(1 cement:4 coarse sand) joints treated with white cement ,mixed with matching pigment, epoxy touch ups ,including rubbing, curing moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite Stone slab of colour black,chrry /Ruby red ,area of slab upto 0.50sqmm

Providing and fixing 18mm thick Gang saw cut mirror polished, pre molded and pre polish machine cut for kitchen platforms, vanity counters windows sills, facias and similar locations of required size approved shade,colour and , texture laid over 20mm thick base cement mortar 1:4(1 cement:4 coarse sand) joints treated with white cement ,mixed with matching pigment, epoxy touch ups ,including rubbing, curing moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite Stone slab of colour black,chrry /Ruby red ,area of slab over 0.50sqmm

Providing and fixing factory made Upvc glazed /wire mesh windows/doors comprising of lead free uPVC multi-chambered fame,sash and mullion/coupler (where eve required)extruded profiles having minimum wall thickness of 1.70mm for series R1 and R2 profiles and 2.10mm for series R3 and R4 profiles conforming to EN 12608 in any shape,colour and design duly reinforced with galvanized mild steel section made of required shape &size as prCPWD specification,UPVC extruded glazing beads,interlocks and inline sash adaptor ( where ever required) of appropriate dimensionEPDM gasket,hardware,SS 304 grade fasteners of miniumi 8mm dia with countersunk head,comprising of matching kpolyamide PA6 grade sleeve for fixing frameto finished wall asper IS 1367:part 1 to 14,plastic packers,plastic caps and necessary stainless steel screws etc Profile of frame,sash &mulion ( if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers,including drilling of holes for fixing hardware and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality all compelte as per approved drawig conforming to CPWD specification and direction of E/I wire mesh/Glazing of plain/toughened/laminated/double glass unit with/without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately.(Note-structural design proof checked from a Goverment Engineering Institure,to be provided by the manufacturer for (i)sites with basic wind speed> 45m/sec as per IS 875-part 3(ii)sites with structure height more than 20m for all wind speeds.

Three track thre panels sliding window with two glazed & one wire mesh panels with aluminium channel for roller track,wool pile,nylon rollers with SS 304 body using R2 series withframe (98mm & above)(30mm&above)& both glazed and fly scen sash(55mm&above)xwith zinc ally (zamak) powder handle on everyglazed panel along with multi-point locking system.(height upto 1.8metre)

Providing and fixing factory made Upvc glazed /wire mesh windows/doors comprising of lead free uPVC multi-chambered fame,sash and mullion/coupler (where eve required)extruded profiles having minimum wall thickness of 1.70mm for series R1 and R2 profiles and 2.10mm for series R3 and R4 profiles conforming to EN 12608 in any shape,colour and design duly reinforced with galvanized mild steel section made of required shape &size as prCPWD specification,UPVC extruded glazing beads,interlocks and inline sash adaptor ( where ever required) of appropriate dimensionEPDM gasket,hardware,SS 304 grade fasteners of miniumi 8mm dia with countersunk head,comprising of matching kpolyamide PA6 grade sleeve for fixing frameto finished wall asper IS 1367:part 1 to 14,plastic packers,plastic caps and necessary stainless steel screws etc Profile of frame,sash &mulion ( if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all comers,including drilling of holes for fixing hardware and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality all compelte as per approved drawig conforming to CPWD specification and direction of E/I wire mesh/Glazing of plain/toughened/laminated/double glass unit with/without high performance coatings as per design requirements and conforming to IS:3548 & IS:16231 shall be paid separately.(Note-structural design proof checked from a Goverment Engineering Institure,to be provided by the manufacturer for (i)sites with basic wind speed> 45m/sec as per IS 875-part 3(ii)sites with structure height more than 20m for all wind speeds.

Three track three panels sliding window with aluminium channel for roller track,wool pile,nylon rollers with SS 304 body using R1 series withframe (33mm & above)(35mm&above)(height upto 0.90metre)

Providing and fixing glazing in aluminium door, windows ,ventilator shutters and partitions etc with EPDM rubber/neoprene gasket etc complete as per the architectural drawings and the directions of E/I.(cost of aluminium snap beading shall be paid in basic item) with float glass panes of 4.0mm thickness(weight not less than 10kg/sqm)

Providing and fixing fly proof wire gauze to windows,clearstory windows& doors with M.S.flat 15x3mm and nuts & bolts complete Galvansied M.S.wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides including all complete job.as per direction of E/I.

Filling the gap in between aluminium frame &adjacentR.C.C/Brick/stone work by providing weataher sillcon sealantover backer rod of approved quality as per architectural drawings and direction of E/I.Upto 5mm depth and 5mm width.

Supplying fitting and fixing M.S.Grill made of 20x6mm M.S.flat square bar as per approved design and drawing properly fabricated with joints continuous fillet welded and finished smooth carriage of grill to work site,hoisting as per building specification and direction of E/I(where materials is not supplied by the deptt)

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all complete as per building specification and direction of E/I.

Steel work in built up tubular ( round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer, including welding andbolted with special shaped washers etc. completeHot finished welded type tubes

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) of total coated thicness 0.50 mm (base metal of minimum o.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, scaffolding raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15M. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Disposal of building rubbish/malba/similar unservicable dismantied or waste materials by mechanical means,including loading transporting,unloading to approved municipal dumping ground or as approved by E/I.beyond 50m intial lead for all leads including all lifts involved all complete job as per direction of E/I.

waterproofing for old land new roof slab providing and laying water proofing treatment on roof slab by applying two component factory designed ready to use acrylic modified flexible materials applied with brush,roller or spray for water proofing coating as per manufacturer specification with foollwing steps:-

a)surface prepaation-providing and cleaning of concrete surface to remove dust oil grease including removal of existing loose paint/coating and cement laitance by cleaning with compressed air & water jet including all materials,labour,tools complete ponding test to be done after plugging all outlets and to be checked from soffit to indentify seepage,leakage.On indentification of seepage,cement grouting to be done with non shrink expanding admixture of sika India Pvt.Ltd/MYK schomberg/Dr.Fixit/Fosroc or equivalent.Providing and reparing of all conners and joints such as those between the parapet wall and the roof slab etc.shall be chamfered with 150mmx150mm fillet of mortar cement sand 1:4) admixed with acrylic polymer of sika/Fosroc/MYK schomberg/Dr.Fixit or equivalent.Before chamfering a prime coat shall be given with the using of arcylic polymer Reparing surface irregularities,damaged concretein base slab,dead cracks if any,with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement shurry including all materials,labour tools commplete.

(b)Ist coat-Applying Ist coat of two component acrylic modified ready to use flexible cementitious mataerials on surface saturated dry roof and in side wall of parapet wall upto 600mm by brush or roller after Ist coat of application 45 grm of Fibre glass cloth to lay when the first layer is still green,Ist coat should be applied @ 1.5kg/sqmt/coat.For the purpose of measurement the entire treated surface will be measured.-

(C) 2nd coat to apply the 2nd coat of two compounent anylic modified ready use Flexible cementitious materials right angle to the Ist coat over the glass fibre laid surface,2nd coat should be applied @ 0.7kg/sqmt/coat .For the purpose of measurement the entire treated surface will be measured.After three days of drying the 2nd coat,The rain water outlets to be plugged and ponding test to be done for 48 hours to indentity seepage,leakage from soffit and if found necessary rectification to be deon as per satisfaction of E/C.The waterproof coating to be protected from damage before screed over it.Water proofing coating to be protected from damgae before screen over it.Water proofing Brand sika Topseal 109hi/Fosroc Brushbod RFX/Dr fixit pidiffin 2K/MYK Aquafin TG.Product performance chemical,Base part A,Acrylic copolymer,PartB-specially graded cementtitious powder Density 1.6 kg/1(,mixed density) at + 27°C-Tensile strength-2N/mm2 after 28 days(with Fibre cloth)(According to ASTM D 2370)Pullout Bond strength-2N/mm2(concrete failure)(According to ISO 4624)Slant shear Bond strength-4N/mm2(According toFIP 5.15) Elongation at Break-35# without Fibre cloth and 20% with Fibre cloth(According to ASTMD 2370)

(d)Protection of treapled surface with PCC-The treated surfaace should be covred with 25mm /50mm PCC of M-20 grade(1:1.5:3) with proper slope(1:120) towards the rain outlets in allernatepenels of 2mtx2mt keeping 6mm gap between the panel joint Integral water proofing admixture conforming to IS 2645 @ of 100ml per bag of cement to be added in the screed concrete (paid separately for this items) All corners shall be chamfered with 150mm fillet.The rainwater outlets shall be just leveled with screed concrete to ensure smooth discharge of water-The peripheral gaps between Pvc pipe outlet and concerte surface should be packed properly with rich concrete and the peripheral mouth to be sealed with moisture insensitive epoxy putty of sika India pvvt.Ltd/MYK.schomberg/Dr.Fixit/Fosroc.For the pupose of measurment the entire treated surface will be measured;

(e) Groove of PCC surface should be filled with polysulphide sealant(paid separately)Brand-sika India Pvt Ltd/MYK schomberg/Dr.Fixit/Fosroc warrantly for five years.

covering of treated surface with P.C,C .Providng 50mm thick cemet concrete M20(1:1.5:3)maintaining slope in alternate 2mtx2mt panels with approved quality of stone chips of 20mm to 6mm sizie graded and cleaned sand of F.M 2.5 to3 includig screening,shuttering and mixingcement concrete in mixer with admixture of integral water proofing and placing in position,striking curing,taxes and royalty all complete as per buidings specification and direction of E/I.panels that has been left should be casted next day.there should be 6mm gap between panels Brand sika plastocrate plus,MYK proof WP 10,,Fosroc-conplastx4211C,Dr.Fixit pidiproof LW+or equivalent.

Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion(i)single socketed pipes.

110mm diameter

Providing and fixing on wall face unplasticised PVC moulded fittings, accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring confirming to I:5382 leaving 10mm gap for thermal expansion.

Single Tee with door

Providing and fixing Chlorinated polyvinyl chloride (CPVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.m.spacing.This included jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc

15mm nominal outer dia pipes

20mm dianominal outer dia pipes

32mmdanominal outer dia pipes

Making plinth protection with bricks of class designation 75 laid on edge in cement mortar 1.6 (1 cement : 6 coarse sand) with 12 mm thick bed of cement mortar 1:6 (1 cement : 6 coarse sand) over 75mm bed of dry brick aggregate 40mm nominal size rammed, consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1:3 (1 cement : 3 fine sand) :

Providing reinforced by organic fibres and/or inorganic synthetic fibres cemet 6mm thick corrugated sheets(as per IS:14871)roofing up to any pitch and fixing with polymer coated J or L hooks,bolts and nuts 8mm dia G.I.plain and bitumen washers or with self drilling fastener and EPDM washers etc.complete (excluding the cost of purlins,rafters and trusses)including cutting sheets to size and shape wherever rrequired.

Providing and fixing stanless steel(Grade 304) railing made of Hollow tubes,channells,plates etcincluding welding,grinding,buffing,polishing and making curvature( wherever required) and fitting the same with necessary stainless steel nuts and bolts complete,I/C fixing the railing with necessary accessories & stainless steel dash fasteners,stainless steel bolts etc,of required sizie,onthe top of the floor or the side of waist slab with suitable arrangment as per approval of Engineer-incharge,(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessoreis such as nuts,bolts,fastners etc)

Providing and fixing white vitreous china pedestal type water closer (European type W.C.pan) with seat and lid,,10litre low level white PVC flushig cistern,including flush pipe with manually controlled device (handle lever)conforming to IS:7231,with all fittings and fixtures complete including cutting and making good the walls and floorsw wherever required.(W.C.pan with ISI marked white solid plastic seat and lid)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chinaflushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flushbend, overflow arrangement with specials of standard make and mosquitoproof coupling of approved municipal design complete, including paintingof fittings and brackets, cutting and making good the walls and floorswherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. bras single hole basin mixer of approved quality and make,including painting of fittings and brackets cutting and making good the walls wherever required:- White Vitreous China Wash basin size 550x400 mm with apair of 15 mm C.P. brass Single hole basin mixere

Providing and fixing wash basin with C.I.brackets.15mmPTMT pillar cock,32mmPTMT waste coupling of standard pattern,including painting of fittings and brackets,cutting and making good the walls wherever required.White vitreous china Flat back wash basin size 550x400mm with single 15mm PTMT pillar cock

Providing and fixing C.P Brass singe lever telephonic wall mixer of quality & Make as approved by E/I. 15mm nominal dia .

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/l.

(3) C.P brass liquid shop container

(b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fittings, 3 mm plywood board and C P hinges to fix with mirror

(1)600x450 mm size

Providing and fixing PTMT Towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600mm long towel rail with total length of 645mm,m78mm wide and effective height of 88mm,weighting not less than 190gms.

Providing and fixing Chlorinated polyvinyl chloride (PVC)pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings..This included jointing of the pipes & fittings with one step CPVC solvent cement trencing,refilling & testing of joints complete as per direction of E/I. concealed work including cutting chases and making good the walls etc.(External work)

25mm dia nominal dia pipes

50 mm dia

Providing and placing on terrace(at all floor levels) polyethylene water storage tank ISI 12701 marketed with cover and suitable locking arrangement and making necessary holes for inlet ,outlet and overflow pipes but without fillings and the base supported for tank.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C.(1:3:6)in foundation and refilling all complete as per specification and direction of E/l.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc all completejob.

Dismantling steel work in built up sections in angles,tees,flats and channels including all gusset plates,bolts,nuts,cutting rivets,welding etc including dismenmbering and stacking within 50 metres lead including all complete job.

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying polished vitrified floor tiles in different sizes(Thickness to be specified by the manufacture) with water absorption’s less than 0.08% and conforming to IS:15622 of approved make in all colours and shades,laid on20mm thick cement mortar 1:4(1cement:4 coarse sand) jointing with grey cement slurry @ 3.3kgk/sqm including grouting the joints with white cement and matching pigments etc. complete.(size of Tile 600x600mm)

Providing designation 75A one brick on edge soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing cement flush pointing (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Centering and shuttering including strutting, propping etc. and removal of form forFoundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing with , cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position (including cariage of bars to work site) all complete as per building specification and direction of E/I. TMT Fe 500( onle valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)

providing Tor steel reinforcement of 10mm,12mm,16mm. dia bars as per approved design and drawing approved design and drawing with , cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position (including cariage of bars to work site) all complete as per building specification and direction of E/I.

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

steel work welded in built up sections/framed work,including cutting hoisting,fixing in position and applying a priming coat of approved steel primer using structural steel etc as required in gratings,frames,guard bar,ladder,railings,brackets ,gatesa and similar works.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick corrugated (2.5" or 4.2" or 6") or step-down(2" or 3" or 6" ) as specified

Supplying and stacking studge at site including royalty and carriage upto5K.M lead complete(sludge measured in stacks will be reduced by 8% for paymet) including all complete job.as per direction of E/I.

Supplying and stacking sludge at site including royalty and carriage uupto 5K.M lead complete including all complete job as per direction of E/I.

Supplying and stacking at site dump manure from local or other approved source including royalty and carriage up to 1K.M (Manure measured in stacks will be reduced 8% for payment) screened through sleve of I.S designation 4.75mm

Providing spreading of sludge,dump manureor/and good earth in required kthickness (cost of sludge,dump manure or/and earth to be paid seperately) including all complete job as per direction of E/I.

Mixing earth and sludge or manure in proportion specified or directed including all complete job as per direction of E/I.

Carriage of materials from nearest approved sources of supply including loading into trucks and unloading from trucks and stacking properly at work site as directed by the E/I.

sand lead 8K.M.

chips lead 22K.M.

Brick lead 8K.M(1K+7P)

Stone Metal 20 km lead

Providing & fixing chaukhats panneling with wooden framed by 12mm thck both side best quality ply and 1.5mm thick water proof laminate pasting,finishing with all materials and labour all complete job as per building specification and direction of E/I.

Providing fitting and fixing of waste coupling in Basins approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of Stop valve approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of Bib cock approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of Bathroom Health Faucet leaded Brass Grade DCB 2 of IS 1264/1997 Bib cock approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of soap dish approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of connection pipe approved quality including all complete job as per building specification and direction of E/I.

Providing fitting and fixing of Floor trap approved quality including all complete job as per building specification and direction of E/I.

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

ARUN KUMAR (BID ID -695401)