SPECIAL REPAIR TO P-112/01 TO 06, P-113/01 TO 06 AND P-114/01 TO 06 (18 QTRS) OF RANE ENCLAVE AT PATIALA MIL STN

Dismantling of brick or terracing tiles of single layers on roofs incl removal of unusable bricks/tiles and removal from site, complete all as specified and as directed

Demolition of Mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) incl removal from site complete all as specified and directed

M&L for wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc. complete all as specified and directed.

M&L for PCC 1:3:6, type C-0 using 12.5mm graded stone aggregates as in filling, mass concrete padding over roof, minimum thickness at khurra as 25 mm to maintain a slope of 1:100 ,complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3kg/sqm and 3 layer minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. Make as approved consisting of a coat of bitumen primer @ 0.40 Ltr/Sqm by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, the layer membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions.

M&L for Cement concrete tiles 25cm x 25cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished and with grey cement and no pigment slurry including 15mm thick screed bed of CM 1:6 complete all as specified and directed.

Supply only liquid water proofing compound complete.

M & L for PCC 1:2:4, type B-0 using 12.5mm graded stone agg as in roof curve, benching, mud stops, steps, coping and the like items slightly rounded or chamfered on the edges complete all as specified and directed.

M&L for efflorescence treatment to walls complete in all respect with following procedure :- (a) Taking down existing plaster , washing/rubbing down loose particles from wall surfaces. Rinse the surface with clean water andand pointing the joints in cement mortar 1:3 complete all as specified. (b) The bricks so pointed shall be cleaned of all dust or deposit using brush and applying two coats of smartcare damp proof coating 2K of make Asian paints or equivalentin berger Paints/Nerolac paints. (c) Thereafter M&L for plastering 15mm thick over the treated surface shall be done with 1:4 cement sand mortar using WPC. Note : The complete item shall be got executed through the authorised applicator of manufacturer only all as directed by Engr-in-charge. Applicator shall be got approved by GE before execution of work.

Demolition of brick work or stone/boulder masonary built in cement mortor incl all quoins,arches.pillars etc complete all as specified

M&L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius bulit in CM 1:6 all as specified.

M&L for taking down cement plaster on brick or stone walls/ceiling etc including raking out joints, hacking for key, scrubbing down with water etc

Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

M&L for cement plastering 15mm thick in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and fair without using extra cement incl fixing of chicken wire mesh as and where directed complete all as specified and as directed by Engineer-in-Charge.

Rendering 10 mm thick in cement mortar 1:6, on brick or concrete surfaces, trowelled to even and fair finish without using extra cement complete all as specified.

5 mm thick cement plastering in cement mortar 1:3 on fair faces of concrete ceiling surfaces finished even & smooth without using extra cement complete all as specified and directed.

M&L preparation of new plastered surface of ceiling and applying three coat of white wash complete all as specified and directed.

M&L preparation of old plastered surface of ceiling and applying two coat of white wash on old decorated surface complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying 02 coats of exterior emulsion paint (light shade) by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer complete all as specified and directed.

M&L for complete removal of old plastered surfaces by mechanical means and preparation of surfaces and applying 02 coats of exterior emulsion paint (light shade) by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/ cantilevers /balcony etc surfaces over & incl a coat of exterior wall primer and minor repairing/crack filling using wall care putty as recommended for under coat by manufacturer of emulsion and primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls including cornices, pillasters etc, and applying two coats of OBD over and incl a coat of interior wall primer over and incl wall care putty to make surface smooth complete all as specified and directed.

M&L for complete removal of existing surfaces of walls including cornices, pillasters etc, and applying two coats of OBD over and incl a coat of interior wall primer over and incl wall care putty to make surface smooth complete all as specified and directed.

Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing ), removing serviceable tiles to store and rubbish off the premises

M&L for 25 mm thick cement concrete type B-2 1:2:4 (12.5mm graded aggregate) as in floor or similar works complete all as specified and directed.

Roughening surfaces of old concrete floor/roof by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified.

Machine cut kota stone slab as in steps/riser/skirting/flooring/landing 18-20 mm thick, set and jointed in cement slurry over & including screed of 20 mm thick in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : 1. All the edges of slabs shall be grinded/cutted at the right angle before laying, so that paper thin, smooth jointing to be obtained. 2. The colour of the slabs shall be uniform.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick polished, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc over and including 15 mm thick rendering in cement mortar 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

M & L for Non - skid Ceramic tiles 7 to 8 mm thick polished, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, inskirting or dados etc over and including 10 mm thick rendering in cement mortar 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick (Square/ rectanglar) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for ceramic glossy finish, joint free premium quality coloured tiles 600 X 300 mm and 7-8 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed.

Taking down chowkhats or frames of any description exc 1.5 Sqm and n. exc. 4 sqm each (without taking off shutters from the frame) including cutting hole to size for receive fresh PCC of hold fast and making good the disturbed surface same complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) not exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified.

S&F factory made Pressed steel frames made of MS sheet of 1.20 mm thickness for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified,size 125x60mm

M&L PCC 1:3:6 type C-0 in 12.5 mm graded stone aggregates hold fast filling inside frame & hold fasts etc complete all as specified

S&F factory made flush shutters 35mm thick ply construction, BWP confirming to IS 2202, solid core construction, with block board core and plywood face panels commercial type on both sides including supply and fixing following items : (a) Mild Steel Butt Hinges 100mm - 3 nos. per leaf (b) Mild Steel Tower Bolt 200mm long - 2 nos per leaf (c) Mild Steel Handles 150 mm - 2 nos. per leaf (d) Mild Steel Sliding Bolt 250 mm - 1 no. per leaf (e) Mild Steel Floor Door Stooper - 1 nos. per leaf.

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) all as specified and including supply and fixing following items : (a) Mild Steel Butt Hinges 100mm - 3 Nos per leaf (b) Mild Steel Tower Bolt 200mm long - 2 Nos per leaf (c) Mild Steel Handles 150 mm - 2 Nos per leaf (d) Mild Steel Sliding Door Bolt/Aldrop 16x250mm - 1 No per leaf

Providing and fixing factory made extruded aluminium casement windows (with provision for cooler) with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60X44.45X1.29 mm and shutters made of 63.5X31.75X1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 nos per leaf and incl hook and eye. Note: complete shutter window will be treated as single unit and paid as single unit

Providing and fixing factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

M&L for Powder coated (Minimum thickness of powder coating 50 micron) for cupboards with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F powder coated aluminium butt hinges 100mm complete all as specified and directed.

S&F powder coated aluiminium tower bolt 150mm long complete.

S&F powder coated aluminium handles 100mm complete.

S&F 9mm thick high density fibre board pre-laminated on both sides (water proof) below & above middle/lock rail in powder coated aluminium doors and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc aluminium beads 20 mm size with and complete all as specified and directed.

S&F factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing and including supply and fixing following items:- (a) Mild Steel Butt Hinges 100mm - 3 Nos per leaf (b) Mild Steel Tower Bolt 150mm long - 2 Nos per leaf (c) Mild Steel Handles 100 mm - 2 Nos per leaf

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for two coat of synthetic enamel paint (finishing coat) over one coat of primer to new steel surfaces of any description any size incl prepration of surfaces complete all as specified & directed.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for preparation of new wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of syntheatic enamel paint over one coat of pink primer all as specified.

S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

M&L for 50mm thick in PCC 1:3:6 type C-1 as in plinth protection surface finished even and smooth without using extra cement comlete all as specified and directed

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 15mm bore.

Supplying and laying CPVC pipes 20mm dia outer dia SDR 11 & Plain and brass CPVC SDR 11 fittings in wall and floor and their making good complete all as specified.

Taking up or down steel tubing and connections incl cleaning for refixing or removing to store yard of size 20mm bore.

Supply and laying Steel water tubing medium grade 20mm bore galvanised with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair Vitreous China wash down pedestal pattern EWC, floor mounted special need white water closet pan with intergral trap including seat cover ,making necessary connections to drain and to flushing pipe antisyphonage pipe etc, jointing to UPVC/PVC/CI and flush pipe including making good to floor complete all as specified and directed.

M&L for Vitreous china squatting pan of Orissa patten size 580 x 440 white with (C I 'P' trap long size) joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in CM 1:3 all as directed and specified.

S&F in repair flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

S&F in repairs vitereous china wash hand basin, white, flat back of size 550 x 400 mm including brackets, waste coupling, waste pipe, cutting for pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F tubular towel rail 600mm long chromium plated fancy type, fixed as in repair complete all as specified and directed.

S&F in repairs Soap dish, CP white approximate size 160x160x90mm complete all as specified and directed.

S&F in repair Brass CP mixer for WHB for mixing hot & cold water screwed down for iron pipe and for 15 mm bore of pipe complete all as specified and directed by Engineer in Charge.

Supply and fixing in repairs 15mm bore C P Angle cock complete all as specified

S&F 450mm long PVC connection of approved quality with brass check nuts at both ends for 15mm bore pipe complete all as specified and directed.

S&F in repair Bib tap cast copper alloy chromium plated, fancy type long body, with capstain head handle screwed down screwed for iron pipe and fixed fo 15mm bore pipe after taking down of old brass bib tap complete all as specified.

S & F in repairs rotational moulded polythene, two layers, water storage tank 1000 Ltrs capacity, white colour, closed top, cylindrical, hoisted and fixed in position including minor repairing , for iron pipe including dismantling of old tank (500L capacity) complete all as specified and directed .

Ball brass valve, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to dia of pipe 20mm as in repairs, complete all as specified and directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply & fixed in repair Brass chromium plated shower rose 125mm size fixed to CPVC pipe complete all as specified and directed.

S&F in repair wall mixer assembly with L bend for shower, brass chromium plated, comprising of centre outlet tap, double inlet for hot and cold water with connecting legs and wall flange fancy type suitable for 15 mm tubing fixed in position complete all as specified and as directed

S&F Mild steel chromium plated jet spray with 1.00 metre tube, (suitable for European seat) complete.

S&F CP peg set of 6 hooks and including all accessories like screws etc as recommended by manufacturer and complete fixing in position complete all as specified and directed.

M&L for PVC floor/multi trap 110mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

M&L for PVC gully traps,Centrifugal type 150 x 150mm size , square or roundmouthed, type 'P' or 'S' fixed in repair complete all as specified abd directed.

S&F in repairs stainless steel grating with anti-foul self closing cockroach trap of 100 mm dia for floor/nahni traps complete all as specified.

S&F in repair for Plantex Quartz sink for kitchen/UV protected kitchen sink/ granite single bowl with drainage board sink/ undermount/topmount (Nano Black) size of bowl 609.6x457.20mm complete all as specified and directed.

S&F Stainless steel plate rack made out of 1 mm thick stainless steel sheet of size 900x750x250mm complete all as specified and directed.

S&F in repair single lever Sink mixer with swinging spout with connecting legs and wall flanges, wall mounted fency type chromium plated cast copper alloy screwed down high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed by Engineer in Charge.

Taking down eaves, gutters and rain water pipes (any sizes or pattern) incl all fitting incl cleaning for refixing or removing to store yard.

S&F PVC (SWR) , 110 mm bore, single socketed in any length with rubber ring joints using solvent as per maunfacture instruction, fixed to walls complete all as specified including fixing of pipe to wall with flat iron clamps of size 25 x 3mm, bolts, washers, nuts, nails etc, complete all as specified and directed.

S&F PVC (SWR) , 110 mm bore, bends any radius

S&F framed work of mild steel Fe- 290 (Gde E- 165) as in doors or gates of angle or cooler stand or other section with gusset plates, rails, braces, etc. and hanging; also incl fastening and fixing complete all as specified and directed.

Demolition of cement concrete (reinforced) in roofs , floors ( other than ground floors ), beams, shelves, landing, chajjas and similar suspended work complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed Conduit(TV/Tele Socket) etc., and making good, cutting not exc 10cm girth and complete all as specified and directed by Engineer-in-Charge.

M&L for TMT Mild steel bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for RCC type B0 1:2:4 using 12.5 graded stone aggregate as in shelves, chajjas, beams and columns, landing, balconies and the like complete all as specified and directed

M&L Formwork to sides and soffits of beams, shelves, haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.

M&L form work to edges of concrete flats, RCC/PCC bands floors roofs and similar works exc 10 cm and not exc 20 cm wide surface finished rough to receive plaster complete all as specified and directed.

M&L for 16-18mm thick granite (of any type) work (table rubbed and polished) in steps, pillars, cooking platforms, window sill and like in cement mortar 1:4 including ponting in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite over and including 15 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for demolition of unreinforced cement concrete including tiles in any position, sunken floor, disposal of unserviceable material, debris and rubbish to a distance n exc 100m as directed by the EIC complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 (using 12.5mm graded stone aggregate), as in Floor, sub base, sunken portion laid to slope required finished fair & even without using extra cement complete all as specified and directed .

Rendering 15mm thick on brick or concrete surface in Cement mortar 1:3, finishing surface w/o using extra Cement, mixed with integral liquid water proofing compound complete all as directed and specified. Note: WPC will be measured and paid separately.

M&L for Plain cement concrete 1:7:12 mix, type E-2 (using 40mm graded Brick aggregate) as in filling of sunken portion complete all as specified and directed.

S&F 25mm dia GI medium grade spouts 60cm long complete all as specified and directed

Dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar and takingdown from wall or getting out of trenches, if required

S& F UPVC SWR pipe (Sch 80) of 110mm bore fixed to walls complete all as specified and directed

S& F for UPVC SWR pipe (Sch 80) of 110mm bore laid in trenches or in floors complete all as specified and directed

S&F PVC (SWR) junction single, (Single T) equal or unequal

S&F PVC (SWR) junction double,(double T/cross), equal or unequal with access door for 110 mm bore complete all as specified and directed by Engineer in Charge.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

S&F PVC cowl 100 mm dia.

S&F PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtr wide and not exceeding 1.50 Mtr in depth and getting out in soft/loose soil complete all as specified and directed Engineer-in-Charge

M&L for concrete bed type D-2 1:4:8 using 40mm stone agg) to drain pipes of any dia complete.

Returning and filling incl spreading, levelling, water and well ramming in layers not exceeding 25cm thick complete all as specified and directed Engr-in-charge

Removal of excavated material n. exc 50 M and depositing where directed at a level not exc 1.5 M above the starting point

Cutting into existing manholes for connecting new drains making good to pipe and rendering cutting out existing benching for and formingbranch channel (1/2 round or 3/4section) in cement concrete 1:2:4 mix type B-1smooth finished and reforming benching as required of any size of dia of pipe.

S&F 18 mm thick HDHMR board of both side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. Make Action Tesa or equivalent

S&F 18 mm thick HDHMR board of single side rigid laminate of approved colour and other side plain white colour fixed with ss screws and solvent cement/ adhesive to make kitchen cabinet, cupboard shutters and shelves complete as per manufacturer’s instructions complete all as specified and directed. Make Action Tesa or equivalent

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs,

S & F Continuous (piano) hinges, width of flap when open 40mm, mild steel, bright finish or electrogalvanised complete all as specified and directed

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long complete fixed in position all as specified.

S&F Stainless Steel 304 grade wire Basket of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required suze complete fixed in position all as specified.

Taking down carefully existing points wiring on surface conduit/concealed conduit including conduit from surface and expect conduit in concealed wiring for light/fan/socket/power/bell from wall & roof along with fitting and fixtures such as switches, sockets, ceiling roses, batten holders, unserviceable light fittings, pieces of wires, gutties, conduit, wooden boards etc removing materials to store for keeping in safe custody of contractor for which the credit has been considered under schedule of credit and making good the disturbed portion of all floor, ceiling etc all as specified and directed.

Point wiring with 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper conductor for one light/fan/bell in new PVC conduit to be terminated in pressed steel terminal boxes with top cover plate including 1.5 sqmm PVC insulated and unsheathed FRLSH single core multi-stranded copper earth continuity conductor controlled by one switch and/or one regulator complete including repairing the surfaces in CM 1:3 and finishing the surface as per existing treatment all as specified and directed by Engineer in-charge Note-I-(Switches and regulators shall be measured and paid for separately). Note-II- ( Wiring shall be done as per colour code in IS for phase, neutral and earth). Note-III- (The cost of modular cover plate and metal flush boxes is deemed to be included in the unit rate quoted for this item). Note -IV - cost of Eye/bottle thimbles used for connection in switches/sockets & MCBs in DBs is deemed to be included in the unit rate quoted for this item. Note:- V- Rate of cutting chasing included in the unit rate quoted for this item

All as per Sl item No 118.00 above herein before but one socket out let 5 pins 5 Amp on the same board with other switches complete all as specified and directed.

All as per Sl item No 118.00 above herein before but for one socket out let 5 pins 5 Amp on independent board complete all as specified and directed.

All as per item No.118.00 herein before but 2.5 Sqmm PVC insulated and unsheathed FRLSH single core multistranded copper conductor incl 2.5 Sqmm PVC insulated and unsheathed FRLSH copper earth wire for switch socket combination 3 pin 15 amps on independent board.

Supply & fix in replacement of Modular switch 1 way, 6 Amps, 1 module, 230 volts complete all as specified.

Supply & fix in replacement of Modular switch 1 way, 16 Amps, 1 module, 230 volts complete all as specified.

Supply & fix in replacement of Modular bell push switch 1 way, 6 Amps, 1 module complete all as specified.

Supply & fix in replacement of Call bell ding dong AC 230 volt single pole complete all as specified.

Supply & fix in replacement of Modular socket 5 pin 6 Amps, 2 module 230 volts complete all as specified.

Supply & fix in replacement of Modular socket 5 pin 6 &16 Amps, combination type 2 module complete all as specified.

Supply & fix in replacement of Modular Fan regulator step type, 120 watts, 2 module complete fixed as in repair all as specified.

S&F ceiling rose surface bakelite surface 65 x 50mm 3 terminals all as specified & directed

Lamp holder including LED bulb 9 W including flexible wire 0.5 Sqmm copper cable all as specified & directed by Engr-in-charge.

New generation energy saving and environmental friendly long life LED building security light 1x35 watts made up of pressure die cast alluminium housing with high power LED as light source and lense embedded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, with all accessories including suitable bracket with 32mm bore light grade GI pipe bemd to shape, including MS clamp of size of required size and PVC cable 1.5 Sqmm twincore from ceiling rose to light fittings complete all as specified and directed by Engineer-in-charge.

Surface Mounted LED Bulk Head Luminaire of capacity 10 watt with ABS Body & Polycarbonate Diffuser, IP54 inc connection with ,with flexible wire 0.5 sqmm copper cable all as specified & directed by Engr-in-charge.

M & L for Sub main wiring with two single core 6.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 6.0 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:-2(two) Runs of 6.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 6.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note 2 :(i) Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces and cutting not exc. 10 cm girth . (iii) Including taking out/down existing unserviceable sub main wiring.

M & L for Sub main wiring with two single core 4.0 Sqmm PVC insulated and unsheathed FRLSH ,stranded copper conductor cable drawn through PVC concealed conduit 25 mm dia including 4 Sqmm PVC insulated unsheathed FRLSH stranded copper conductor cable as earth wire all as specified and directed by Engineer-in-charge. Note 1:- 2 Runs of 4.00 Sqmm Copper conductor cable, 1 Run of PVC conduit & 1 Run of 4.00 Sqm Copper conductor Earth wire shall be measured as one unit) Note2 : Rate quoted for this items shall be inclusive of the cost of (i) Rigid non-metallic PVC conduit of 25 mm dia with tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. (ii) Cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to match the existing surfaces, cutting not exc. 10 cm girth . (iii) Taking out/down existing unserviceable sub main wiring.

Supply and fix Sheet metal enclosure 8 ways double door for DBs when MCBs are to be used 240,volts including 200 Amps standard bus bar of suitable size and common neutral link all flush mounting type, drilling holes for incoming and out going cables with IP 43 protection complete all as specified & directed by Engr-in-charge.

Supply and fix MCB , SPN, 240 Volts ,40 to 63 amp for fixing in DBs of including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

Supply and fix MCB, single pole 240 volts 6 to 32 Amp capacity for fixing in DB’s including proper thimble connections complete all as specified and directed by Engineer-in-Charge.

M & L for Earthing complete with galvanized iron earth plate electrode of size 600x600x6.0mm , buried directly in ground (earth pit not less than 2.25 mtrs below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4.0 mm dia by means of bolts , nuts , check nuts and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate 20 mm dia watering pipe medium grade 1.70 mtr long with a plug at top, GI protection pipe light grade 15 mm dia from earth pit to main board including PCC pit in cement concrete 1:2:4 along with CI frame and cover 10mm thick duly hinged to CI frame as shown in the electrical plate No3 of SSR 2009 part 1

Supply and fix Tube light fitting Self Ballasted LED Batten. Extruded Thermoplastic body with PC Diffuser in square LED Batten 18/20W 6500K of capacity ,20 watt,4 ft long incl 3 core flexible wire 0.5 sqmm copper cable all as specified and directed by Engr-in-charge.

Supply and fix in replacement of elegatly designed sleek surface mounted pressure die-cast aluminium LED luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver of capacity 20 W LED of 5000 K and making good the existing surface as per existing complete all as specified & directed.

Supply and fix Exhaust fan AC single phase 230/240 v of size 300 mm sweep 900 rpm metal body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making Louver complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of ceiling fan,Exhaust fan & geyser after necessary cleaning painting making serial No complete all as specified and directed by Enginner-in-charge.

Supply and fix Exhaust fan AC single phase 230/240 v of size 250 mm sweep 900 rpm Engineering thermoplastic body, high efficiency motor, dynamically balanced blade for better performance and corrosion-resistant powder coated metallic finish including hole making Louver complete all as specified and directed by Engineer-in-Charge.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified and as directed by Engineer-in-charge.

S & F modern energy efficient bedroom Muziris wall decorative light of capacity 20 watt single headed 240 volt, IP20 rating, controller type (push button), product weight 1.04 kg, body material (metal), power source (corded electric),Lamp base E27, Colour(bronze) incl electrically connection , including removing of unserviceable decorative light fittings of any description complete all as specified and directed by Engr-in-charge. Make: Philips model No 31425 or as equivalent.

Material and labour for sand cushioning for cables 8 cm below the cable and 15 cm above with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed.

Cutting of hardstanding floor/wall for laying of cable including matching with suface by using cement concrete all as specified and directed.

M&L for Boring of holes under road, pavement, hard standing by trench-less technology using ultrasound technique and necessary machine suitable to pass through 40 to 80 mm bore GI tubing and cable etc complete all as specified and directed. Note: GI pipe shall be measured and paid seperately under relevant item.

Supplying & laying factory made unreinforced Precast concrete cable covers class LV type 1, flat, Size 250x150x40mm laid in trenches as protection to cables complete all as directed by Engr-in-Charge

Material and labour for replacement of GI tubing light grade 40 mm bore for passing through cables under the floor ,along the wall or along the pole complete all as specified and directed.

XLPE Insulated ,screened, PVC bedded, galvanized steel wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core supplied & laid in replacement complete all as specified& directed by Engineer-in-Charge.

Taking down existing LT panel board (Meter Box) located at Map block and supply and fixing sheet metal enclosure board made of 1.6 mm thick metal sheet and painting 2 coats with synthetic enamel paint over a coat of red oxide primer including Aluminium bus bar of suitable rating and fixed with wall for fixing MCCB 4P 125 amp and electric meters complete with wiring, fitting and accessories, locking arrangements with handle (adequate size and adequate depth for the following equipments, internal wiring and termination of external cable, lugs and glands and conduits as required) comprising of following. (a) Incoming 125 Amp 4 pole MCCB 25 KA-01 Nos.(Main incomer) (b) Aluminium Bus bar rated 200 Amp capacity. (c) 10Amp DP/SPN MCB-01 No (Outgoing for stair case and garrage) (d) 63 Amp DP/SPN MCB-06 Nos (Outgoing for Qtr meters) (e) Taking down and Refixing of electric meter energy meters single phase 240Volt 40Amps 50HZ -06 Nos.

Please Enable Macros to View BoQ information