COMPREHENSIVE REPAIRS/ MAINT TO CERTAIN BLDGS OF OTM ACCN AND CENTRAL INSTITUTES UNDER AOR OF MAC GP AT MIC and S UNDER GE(S) AHMEDNAGAR

Amount

Dismantling of Kota stone slab, Granite of any description in floor, laid, bedded & pointed in any mortar, Cudappah slab supports of platform & interlocking paver blocks bedded on sand all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floor & paving n.exc. 15cm thick below or above ground level all as specified and as directed.

Demolition of brick/stone/ block masonry built in cement or cement lime mortar all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls etc., including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and as directed.

Taking down shutters of any description, area exceeding 1 sqm but not exceeding 2 sqm each and refixing in the same opening after easing all as specified and as directed.

Taking down shutters of any description, area exceeding 1 sqm but not exceeding 2 sqm each all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area not exceeding 1.5 sqm each all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames), area exceeding 1.5 sqm but not exceeding 4 sqm each all as specified and as directed.

Dismantling asbestos cement (corrugated, Semi-corrugated etc.) sheets in roof coverings including ridges all as specified and as directed. .

Taking up or down 15 mm bore steel tubing and connections, including cleaning for re- fixing if required all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for re- fixing if required all as specified and as directed.

Taking up or down 25 mm bore steel tubing and connections, including cleaning for re- fixing if required all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Excavation over areas n. exc 1.50m in depth in any type of soil for foundation etc all as specified and as directed

Excavation in trenches not exc 1.50m wide and not exc 1.50m deep for foundation etc . or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and as directed

Removing excavated soil to distance not exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed

M&L for moorum filling in floors or paving, laid in layers n.exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core of gauge exc. 63 mm but n. exc. 100 mm, deposited spread and levelled in layers n. exc. 15cm thick, including watering and rammed etc. complete all as specified and as directed.

M&L for PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete all as specified and as directed.

M&L for RCC, 1:2:4, type B1 using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and as directed.

M&L for precast cement concrete block masonry with solid blocks of PCC (1:5:8), exc 10 cm width, built in cement mortar 1:6, complete all as specified and as directed.

M&L for brick work with fly ash ' bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed.

All as per item No 23 above but except bricks. (Note: Serviceable bricks obtained from demolition shall be reused.)

M&L for cutting chases for pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc. and making good, cutting not exc 10 cm girth all as specified and as directed..

S&F 35 mm thick, second class hard wood glazed and skeleton shutters, factory made, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamferesd or rounded, fitted with cut and mitred beads for securing glass etc., for windows and ventilators, etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed.

S&F 35 mm thick second class hard wood, factory made, plain framed panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part I) kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F solid PVC door frame of size 50x47 mm, made out of 5mm PVC sheet reinforced with MS square tube as per specification drying as per manufacture instructions including all necessary fitting complete complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing all as specified and as directed.

M&L for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade), Calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/Sqmm, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed. Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department. (ii) M.S. hold fast/ lugs or SS dash fasteners shall be paid separately.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative flush/panel door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F 150 mm size aluminium anodized barrel tower bolts of extruted section and fixed.

S & F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F 100 mm size butt hinges medium weight, cold rolled mild steel and fixed all as specified and as directed.

S&F 100 mm size butt hinges medium weight, stainless steel and fixed all as specified and as directed.

S&F in repairs, 300mm size,MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and as directed.

S&F 125 mm size extruded aluminium alloy handles, fabricated type, anodised all as specified and as directed.

S&F 125 mm size extruded brass handles, fabricated type all as specified and as directed.

S&F in repair drapery rod fancy type made out of 25mm dia MS PVC coated pipe having wall thickness 0.63 mm bright finish ,with decorative type hard plastic finial as end holders with 02 Nos MS brackets fixed with SS screws or rawl plug complete all as specified and directed.

S&F in repair SS fancy type curtain rod with brackets and knobs at end fixed with SS screws & rawl plug complete all as specified and directed.

S&F in repairs, tubular towel rail, brass chromium plated, 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as specified and as directed.

S&F in repairs 5 inches heavy duty Vanilla door stopper mounted with rubber tip of aluminiam alloy body fixed in floor all as specified and directed.

S&F in repairs, galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18 mm etc complete all as specified and as directed.

S&F in repairs SS wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aparture 1.18 mm etc complete all as specified and as directed.

M&L for mild steel TMT bars, 6 to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Hard drawn steel wire fabric n. exc 4 Kg/sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections conforming to Fe 410 -W (Gde- E- 250) quality- A ) including distance pieces, cleats etc. all as specified and as directed.

S&F mild steel windows, side hung, including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete including 12 mm square guard bars as specified in relevent IS all as specified and as directed.

S&F mild steel windows, side hung, including projecting type hinges with steel handles and steel peg stay complete without glazing bars dovetailed or welded complete including 12 mm square guard bars as specified in relevent IS all as specified and as directed.

S&F mild steel ventilators, top hung type icluding steel handles and steel peg stay complete with glazing bars dovetailed or welded complete as specified in relevent IS all as specified and as directed.

S&F mild steel windows/ventilators, fixed type with glazing bars complete all as specifed and as directed

S&F mild steel framed work such as grills, framed guard bars and similar work conforming to Fe-290.Gde-E-165, welded to steel ventilators & window complete all as specified and as directed.

S&F pressed steel doors frames of size 105 mm x 60 mm x 1.25mm thick, with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed.

M&L for welding in repairs, n exc 2.50cm length, thickness of metal to be welded n exc 6mm complete all as specified and as directed

S&F powder coated aluminium door with frame and shutter in two panels (top and bottom) made out of aluminium sections (make Jindal or equivalent) including 5 mm thick sheet glass, aluminium cleats, rubber/ neoprene beading, all necessary fittings and locking arrangements etcall as specified and as directed and comprises of following sections :- (a) Vertical style- 47 x 44.5 x 2.25 mm thick @ 1.15 Kg/m (Min) (b) Lock rail- 114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (c) Bottom rail-114.6 x 44.45 x 2.3mm thick @ 2.06 Kg/m (Min) (d) Frame-47.5 x 44.45 x 2.25 mm thick @ 1.12 Kg/m (Min)

S&F in repairs, double action floor spring hydraulically regulated made up of min 1.25mm thick aluminium alloy sheet foundaion box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and as directed .

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.548 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed.

S&F laminated Gypsum tile board 8mm thick with textured white colour PVC film on the face side and metalized polyster (MPL) film on rear side in ceiling as per manufacturers instructions of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, including dismantling existing false ceiling work of any description all as specified and as directed..

M&L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and as directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by GE, having tensile strength of 550 Mpa as in roof covering/ridges/valley gutters/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE

M&L 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, wall cladding, fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as specified and as directed.

Fixing only 6mm thick asbestos cement, corrugated or semi corrugated sheets in roof, wall cladding, fixed with 'L' type or 'J' type or cranked hook bolts, washer etc complete all as specified and as directed.

M & L for Water proofing treatment to floor & vertical surfaces of sunken portion complete comprising the following (floor area of WC/Bath exceeding 1.5 sqm but not exceeding 3 sqm) :- (a) After demolition of floor and lime concrete etc. remove all loose particles along with existing water proofing treatment (any no. of layers) with wire brushes and cleaning the surfaces with water. (b) Brushing cement slurry with 1.2 kg of cement per square meter duly blended with & including water proofing compound. (c) 15mm thick (Average thickness) plaster in cement mortar (1:4) mixed with WP compound on sunken surface including walls. The corner of sunken portion shall be rounded in concave shape and adequate slope shall be made during plastering to accommodate sump pipe and curing the sunken portion with water minimum for 48 Hrs by ponding. (d) Applying self adhesive type APP based polymeric membrane minimum weighing not less than 3.6 kg/sqm and minimum 3 mm thick reinforced with polyster non-woven fabric (weight not less than 150 gm/sqm (e) M&L for PCC 1:7:12 for fillin of sunken portion after conceling all membrane and sealing all joints to the entire with broken bats and light weight, and provide hole in the wall and fix 600 mm long 20 mm dia GI spouts light grade, PCC 1:3:6, type C1 (using 20 mm graded stone aggregates) filling complete all as satisfaction of Engineer-in-Charge. Note- The rates include for drilling of the hole RCC @ 1.00 m centre to centre, to a depth to a length of 30 mm and fixing of PVC pipes of dia 15/20 mm laid dry and grouting with cement slurry mixed with can bax 100 chemical with pressure grouting with minimm 3 Kg/Sqm complete all as specified and directed.

M&L in repairs, for water proofing treatment to RCC roof slab, including parapet, comprising with the following treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the old concrete slab by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish n exceeding 100 mtr distance from starting point. (ii) Screed bed or bedding layer of 10 mm thick cement mortar 1:4 with mixing of WPC @ 3% by weight of cement or as per manufacturers instructions and surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3kg/sqm. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm. Note: Water proofing compount will be measured & paid separately.

Supply only liquid water proofing compound complete, ISI mark all as specified and as directed.

M&L for machine cut kota stone flooring, 18-22 mm thick (size of kota stone slab 16"x22") laid over and including 20 mm thick bedding layer of cement mortar 1:6 jointed with grey cement slurry mixed with pigments to match the shade of slab including cutting, rubbing and mirror polishing including removing dust complete all as specified and as directed.

All as per serial item No. 68 here-in-before but 18 to 20 mm thick kota stone on vertical surfaces such as in skiting /dado of size as required at site over and including10 mm thick backing coat of cement mortar (1:4) complete all as specified and as directed.

M&L 18-20 mm thick pre-polished granite stone slab of approved shade as in table top, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, including full round moulding the edges, laid over and including screed bed 15mm thick in cement mortar 1:4, jointing, pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polishing to achieve mirror finish complete all as specified and as directed. Note: colour and shade as Approved by GE.

M&L for machine cut cudappah stone slab 20-25mm thick laid over and including 20 mm thick bedding layer of cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base of floor all as specified and as directed.

M&L for 100mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base of floor all as specified and as directed.

M&L for glazed coloured ceramic tiles 7mm thick (plain or printed), area of each tile 350x250x7 mm/450x350x7 mm thick , as on vertical surfaces like dado, skirting etc laid over and including 10 mm thick backing coat in cement mortar 1:4, jointed in neat cement slurry and pointed in coloured cement to match with colour of tiles complete all as specified and as directed. Note:Colour and shade approved by Engr-in -charge

M&L for non skid coloured ceramic coloured tiles 7-8mm thick (square or rectingular)area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc Complete all as specified & directed. Note:Colour and shade as approved by Engr-in -charge.

M&L for light shade vitrified coloured tiles ,8-9 mm thick (square / rectangular), area of each tile n exc 0.36 sqm, in floor etc laid over and including 20 mm thick bedding layer in cement mortar 1:6, jointed in grey cement slurry and pointed in white or coloured cement to match with colour of tiles all as specified and as directed. Note:Colour and shade approved by Engr-in -charge

All as per serial item No 77 above but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for vitrified tiles double charged (light shade), 8 to 9mm thick (square/ rectangular) polished, area of each tiles not exc 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including 20 mm thick screed bed in cement mortar 1:6, complete all as specified and as directed.

All as per serial item No 79 above but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for non skid coloured ceramic coloured tiles 7-8mm thick (square or rectingular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc Complete all as specified & directed. Note:Colour and shade as approved by Engr-in -charge.

M&L for non skid coloured ceramic coloured tiles 7-8mm thick (square or rectingular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 etc Complete all as specified & directed. Note:Colour and shade as approved by Engr-in -charge.

All as per serial item No 82 above but in dado / skirting or on vertical surfaces, laid over and including 10 mm thick backing coat in cement mortar 1:4 .

M&L for digitally printed machine pressed, factory made paver tiles, 300mm x 300mm x 10 mm thick, as approved by GE as in floors, laid over and including screed bed 15mm thick in cement mortar 1:4, set, jointed and pointed in neat cement slurry all as specified and as directed.

M&L for 60mm thick, factory made, chamfered edge, cement concrete interlocking paver blocks (glossy/ rubber matt finish) of M-35 grade with approved colour, design & pattern of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed. Note : Size, shape, pattern and shade shall be as approved by GE.

M&L for rendering 15 mm thick on other than fair faces of brick work /concrete surfaces in cement mortar 1:4, mixed with liquid water proofing compound, finished even and fair without using extra cement complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick masonry surfaces or concrete surfaces, finished even and smooth without using extra cement including sagol finish complete all as specified and as directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling finished the surface even & smooth without using extra cement complete all as specified & directed.

M&L for raised pointing to random rubble masonry, uncoursed or brought to course in cement mortar 1:3, including racking out joints etc. complete all as specified and as directed.

S&F GI wire netting 0.90mm dia and 12mm size of mesh and fixed to wall, ceilings, beams etc including all laps and waste including making V groove in crack portion and filled with cement mortar 1:2 etc complete all as specified and directed.

M & L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

M & L for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered or unplastered surface of walls and applying two coats of oil bound distemper over a coat of chalk whitining complete all as specified and as directed.

M & L for preparation of plastered surfaces of walls and applying one coat of chalk whiting primer over a coat of 1 mm thick (average) white cement putty, sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper over a coat of primer etc complete all specified and as directed

M & L for complete removal of existing treatment, from old plastered decorated surfaces of walls and applying a coat of 1 mm thick (average) wall care putty, sanding the surfaces till smooth finish is obtained for receiving paint complete all specified and as directed

M&L for preparation of new plastered or unplastered surface of walls and applying two coats of oil bound distemper using roller complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls applying two coats of cement base paint over a coat of primer all as specified and as directed

M&L for preparation of new wall surfaces and applying applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/liter and UV resistant as per IS 15489: 2004, Alkali & fungal resistance , dirt resistance exterior paint of required shade with silicon additives @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 kg/10 sqm all as specified and as directed.

M&L for complete removal of existing treatment from wall surfaces, filling cracks/ holes by acrylic crack filler and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/liter and UV resistant as per IS 15489: 2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 kg/10 sqm all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/metal frames including punching or drilling out pins/spring clips complete all as specified and as directed

S&F 3 mm thick frosted/figured glass and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

S&F 3 mm thick plain sheet glass and glazing with oil putty in square n exc 0.5 Sqm in each pane to steel windows including glazing pins etc. complete all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over one coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for 15 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F 16 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Fixing only old serviceable 15mm bore GI tubing medium grade with all fittings (new) and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

M&L for 20 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Fixing only old serviceable 20mm bore GI tubing medium grade with all fittings (new) and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

M&L for 25 mm bore GI tubing medium grade with all fitting and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

Fixing only old serviceable 25mm bore GI tubing medium grade with all fittings (new) and fixed complete on walls and ceilings or laid in floors etc complete all as specified and as directed.

S&F in repairs, rotational moulded polyethylene water storage tanks colour white (cylindrical vertical with closed top), 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

All as per item No. 113 above but 1000 ltr capacity

All as per item No. 113 above but 2000 ltr capacity but with 20 mm dia ball valve

All as per item No. 113 above but 5000 ltr capacity but with 25 mm dia ball valve

Disconnecting existing water tanks exc 250 ltrs but n. exc 500 litres capacity, setting aside (or lowering if required) for cleaning and removing all scale and dirt, etc. from tanks and mouths of circulating pipes etc. and hoisting reconnecting and re-fixing in position complete all as specified and as directed.

All as per item No. 117 above tanks exc 500 ltrs but n. exc 1000 litres capacity

S&F in repairs PVC cover/lid for rotational moulded polyethylene water storage tanks of any capacity including fixingwith necessary device complete all as speified and as direted

S&F in repairs, bib tap, 15mm dia cast copper alloy chromium plated, with crutch or butterfly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs, 15 mm bore pillar taps, cast copper alloy with capstan heads, fancy type, chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore brass chromium plated wash basin mixer for mixing hot and cold water for wash hand basin screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repairs 15 mm bore brass chromium plated kitchen sink mixer for mixing hot and cold water for wash hand basin screwed for iron pipe and fixed complete all as specified and as directed.

S & F in repairs, brass chromium plated wall mixer for mixing hot and cold water and bend for connecting shower, screwed down for iron pipe, 15mm bore and fixed complete all as specified and as directed.

S&F in repair 15mm bore brass spindle for bib taps,pillar taps,stop cock, basin mixer, wall mixer etc fixed complete all as specified and directed.

S & F in repairs, stop valves/ angular stop valve 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repairs, 20 mm bore, gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium ball rod and high density plastic ball screwed for 15mm bore iron pipe (Minimum weight 142 gms) complete all as specified and as directed.

S&F in repairs, ball valves high pressure PTMT with epoxy coated aluminium ball rod and high density plastic ball screwed for 20mm bore iron pipe (Minimum weight 210 gms) complete all as specified and as directed.

S&F in repairs, grating doom, 100 mm dia with waste hole of PTMT (Minimum weight 40gms) complete all as specified and as directed.

S&F in repairs, 32/ 40 mm bore PVC flexible outlet pipes for wash basin/ sink/ urinal fixed complete all as specified and as directed.

S&F in repairs, push cock faucet 15mm dia, cast copper alloy, fancy type chromium plated screwed down complete all as specified and as directed.

S & F in repairs, PVC connections, 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S & F in repairs, PVC connections, 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

S&F in repairs, 110 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 75 mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors all as specified and as directed.

S&F in repairs, 110mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed.

S&F in repairs, 75mm bore, PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls all as specified and as directed.

S&F in repairs, 110 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) bends with oval access door of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) bends with oval access door of any radius complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) branch piece, double (double Y) equal or unequal with oval access door of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) branch piece, double (double Y) equal or unequal with oval access door of any radius complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) junction single (Single T) equal or unequal with oval access door of any radius complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) junction single (Single T) equal or unequal with oval access door of any radius complete all as specified and as directed

S&F in repairs, 110 mm dia PVC (SWR) vent cowl complete all as specified and as directed

S&F in repairs, 75 mm dia PVC (SWR) vent cowl complete all as specified and as directed

M&L in repairs, for 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement to waste pipe fixed in cement concrete type (1:2:4) type B1all as specified and as directed.

S&F in repairs, CP health faucet (hand shower) with 8 mm dia, 1200 mm long flexible tube, wall mounted / hooked all as specified and as directed.

S&F in repairs, brass chromoum plated shower rose of size 125mm dia with or without swivel joints and fixed to steel pipe complete all as specified and as directed.

S&F in repairs, stainless steel toilet paper holder and fixed to wall with screws complete all as specified and as directed.

S&F in repairs, vitreous China, white, squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete including flush pipe and connecting to trap / flushing cistren and making good to floor complete all as specified and as directed.

S&F in repairs, vitreous china wash down water closet ( pedestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S&F in repairs, vitreous china premium / 1st quality wash down water closet wall hung EWC white / ivory / off white (closed pattern incl all necessary accessories like rag bolts / gel gasket etc. including flushing cistern, connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for pedestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and directed by Engineer-in-charge.

S & F in repairs, 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc complete all as specified and as directed.

S & F in repairs vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets including pillar tap 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed.

S&F in repairs vitreous china counter top wash hand basin, 525mm x445mm size including brackets, pillar tap 15 mm bore chromium plated, fancy type, cast copper alloy with capstan head, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed. Make : Johnson Cat Part No P1614PW0301 or equivalent of makes specified as approved by GE.

S&F in repairs, stainless steel sink with drain board made of 1mm thick sheet for kitchen including plugs, washers, waste pippe, cast iron cantilever brackets, connecting union to pipe, over all size 915 mmx 460 mm with bowl size 410 mm x 330 mmx 160 mm all as specified and as directed.

S&F in repairs, stainless steel sink made of 1mm thick sheet for kitchen including plugs, washers, waste pipe, cast iron cantilever brackets, connecting union to pipe, over all size 495 mmx 420 mm with bowl size 410 mm x 330 mmx 160 mm all as specified and as directed.

S&F in repairs vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm (minimum) white , with grating and union for discharge pipe (excluding flushing cistern, flush pipe) including urinal spreader of brass chromium plated for fixing with 15 mm dia pipe, PVC connection, 40mm PVC waste pipe & 40 mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe, complete all as specified and as directed.

S&F in repairs vitreous China Half stall urinal size of 390 x 360 x 615 mm (minimum), white with grating and union for discharge pipe (excluding flushing cistern, flush pipe) including urinal spreader of brass chromium plated for fixing with 15 mm dia pipe, PVC connection, 40mm PVC waste pipe & 40 mm waste coupling providing and fixing plugs, bedding urinal against wall in mortar 1:2, securing urinal to plug, with and including 60mm long screws, pointing around urinal back in cement, fixing flush pipe complete all as specified and as directed. Make : Johnson Cat Part No P0519PW0703 or equivalent of makes specified as approved by GE.

NATHKRUPA CONSTRUCTION (BID ID -3139369)

AMAR CONSTRUCTION (BID ID -3140041)

M/s. N D Karande (BID ID -3139384)

MATOSHREE CONSTRUCTION (BID ID -3139983)

DHANANJAY BABAN KALANE (BID ID -3139632)

M/s IBEX Engineers and Contractors (BID ID -3139433)

M/s Mauli Construction (BID ID -3139365)

M/S. Z.K.ENTERPRISES, AHMEDNAGAR (BID ID -3140002)