SPL REPAIRS TO BLDG NO. P-11 AND P-12 AT SWIMMING POOL NO. 2 JCOs/Ors, REPLACEMENT OF TILES AND PLASTER WORK OF TOK BATHROOM AT ARMY AVN SQN, INCLUDING CERTAIN REV AND MINOR WORK AT DIN MIL STN UNDER GE DINJAN

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc not exceeding 10 Sqm on plan and getting out in Soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil complete all as specified and as directed.

Removing excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m abovestarting point complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface in soft/loose soil complete all as specified and as directed.

M&L for 100mm thick granular sub base of grading III as per IRC 15:2011, rolled and consolidated with hand roller to gradient and camber required complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block, glossy finish of approved colour, design and shape and size conforming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1, (using 20 mm graded stone aggregate) as in benching, coping, lintel upto 1.5m span cast in situ including necessary form work complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and as directed.

S&F for angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for mild steel screw bolts of 11 to 15mm dia of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exceeding 10cm and not exceeding 15cm long complete all as specified and as directed.

Supply only chain link MS galvanisd fencing, any size or type complete all as specified and as directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed

S&F in repair galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. (each line wire to be measured) complete all as specified and as directed.

M&L for TMT bar 10mm dia and over cut into length, bend to shape required including cranking bending spirally for hoping as in tie bar for fixing chain link fencing complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description, not exceeding 10 cm width or girth when unconnected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

M&Lfor septic tanks in soft/loose soil, foundation (1:4:8) Type D-2 brick work in cement mortar (1:4) precast RCC M-25 (Design Mix) cover slab and manhole cover slab vent shaft and sludge chamber etc complete for 50 users including necessary earth work and excavation as shown in Drg No. TD/SZ/504 (Sheet No 1/1) complete all as specified and as directed.

M&L for soakage well in loose/soft soil, foudation with PCC (1:3:6) Type C-2, brick work with cement mortar (1:4) as in honey combed and solid, RCC M-25 (Design Mix) concrete including intercepting chamber screen chamber brick work in cement mortar, RCC cover slab in M-25 (Design Mix) filling with brick bats complete of size 1.80 mm dia and 3 mtr deep as shown in Drg No. TD/SZ/502 (Sheet No 1/1) complete all as specified and as directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkats or frames, exceeding 1.5 butnot exceeding 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F for pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

M&L for 35mm thick second class hard wood plain, framed, panelled shutters (any number of panels), with panels of 12mm thick veneered particle board medium density with commercial face veneers: supplied and fitted to chowkats, sizes/section of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed.

M&L for 35 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (a) of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed.

S&F for 30 mm thick, second class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauge, etc, divided in to squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamfered or rounded as in SSR Part I Section 8 clause 8.24 (b) of members of shutters shall be as specified in SSR Part I, Section -8, clause 8.24 (a) complete all as specified and as directed.

S&F for solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour 5mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and as directed.

S&F for 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

S&F for 100 mm size, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and as directed.

S&F for 200 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and as directed.

S&F for 125 mm size, aluminium handles, cast type, anodised to a bright natural, mat finish not be less than grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for aluminium alloy anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples including timber bead complete all as specified and as directed.

S&F for 3 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

M&L for anodised aluminium section, medium anodic coating of grade AC 15 for frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed.

S&F for anodised aluminium door shutters, aluminium section weighin 0.55 kg/m including necessary joining cleat glazing clips, rubber neoprene packing handle 2 no. in each door, hinges, anodised aluminium snap beading screw etc. including powder coating of minimum 50 micron thickness complete all as specified and as directed.

S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including painting with one shop coat of zinc chrome primer complete all as specified and as directed.

S&F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded including painting with one shop coat of zinc chrome primer complete all as specified and as directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

S&F for mild steel flat iron clamps etc in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

S&F for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets and frame work any type complete all as specified and as directed.

S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed. Make of E-Board: Eternit Everest / lafarge/ Armstrong/Visaka Industries Ltd.

Dismantling timber scantlings 40 Sq.cm and over in section, in any position complete all as specified and as directed.

M&L for second class hardwood, scantlings, clean sawn, in unframed work complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

M&L for brick work using locally available first class bricks sub class 'B' bricks (old size brick), straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water complete all as specified and as directed

M&L for rendering 15 mm thick in cement mortar (1:4) on other than fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar (1:4) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in cement mortar (1:3) on concrete surfaces as in ceilings (sunshed, chajja etc) and finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) mixed with integral water proofing compound weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid separately against respective item.

Supply only liquid water proofing compound (ISI marked) complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistent primer complete all as specified and as directed.

M&L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of primer over 2mm thick wall care putty to a smooth surface complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation new external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of ceilings by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls by complete removal of existing treatment including chalk whiting on wall etc and applying two coat of distemper oil emulsion over a coat of chalk whiting primer for distemper including wall care putty (minimum 1.5mm thick) complete all as specified and as directed.

M&L for preparation old decorated external surfaces of wall, chajja, facia etc by complete removing old paints by mechanical scrubber without disturbing the plastered surfaces and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls by complete removal of existing treatment including primer on wall etc and applying two coat of cement based paint over a coat of alkali resistant primer suitable for cement based paint complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old painted wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

Demolition of plain cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness. (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in any position exceeding 15 cm thickness above ground floor, etc complete all as specified and as directed.

M&L for hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for 150 mm thick, plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and as directed.

M&L for 100 mm thick, cement concrete (1:2:4) type B-2 (using 40mm graded stone aggregate) as in hard standing/path, etc, and finished the cement concrete surfaces even and fair without using extra cement making impressions of expanded metal whilst the concrete is green complete all as specified and as directed.

M&L for forming construction joints 30mm deep x 10mm wide, filled with sealing compound Grade 'B' complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base etc complete all as specified and as directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) complete all as specified and as directed.

M&L for 25 mm thick, plain cement concrete (1:2:4) type B-0 (using 12.5 mm graded stone aggregate) as in floors & finishing the surfaces even and smooth with using extra cement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing the rubbish off the premises complete all as specified and as directed.

M&L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for non-skid, ceramic, coloured tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for non-skid, ceramic, coloured tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, provided on vertical surfaces of walls such as skirting, dados etc, including 10 mm thick bedding in cement mortor (1:4) and set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for glazed, ceramic, coloured tiles of size 300mmx200mmx7-8mm thick, on vertical surfaces, including 10 mm thick backing of cement mortor (1:4) and set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and as directed.

M&L for chequered cement concrete tiles of size 25cm x 25cm x 20mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for prepolished coloured Chequered cement concrete tiles of size 30cm x 30cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Supply, laying, connection and testing, 15mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for reuse at same site or other site complete all as specified and as directed.

Supply, laying, connection and testing, 20mm bore, steel water tubing, galvanised, medium grade conforming to IS 1239 (Part -1):2004 with all fittings conforming to IS 1239 (Part -2):2011 and fixtures complete fixed to walls and ceilings or laid in floors, etc complete all as specified and as directed.

M&L for cutting chases not exc eeding10cm girth to brick or concrete wall, for concealed water tubing, pinning in, making good to facings where required and pointing in cement mortar (1:3) and to ends or edges of landings, steps,cills, sunshades, shelves, lintels etc;complete all as specified and as directed.

Demolition of reinforced cement concrete in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for plain cement concrete (1:2:4) type B-1, (using 20 mm graded stone aggregate) as in lintel upto 1.5m span, cills and other similar band, plinth course, parapet, railing upto 60cm height, coping, kneelers, bed plates etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and as directed.

M&L for precast cement concrete louvres and jallies of 25mm thick (measured solid), type C0, 1:2:4 (12.5mm graded aggregate) including all mouldings as set in cement mortar set in cement mortar (1:4) complete all as specified and as directed.

M&L for TMT steel bars 10mm dia and over, cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F for semi-pedestal pattern (Anglow-Indian type), vitreous china water closet pan, white, with 'P' or 'S' trap, including flushing pipe, etc complete and making good to disturbed surfaces of floor by filling with PCC (1:4:8) type D-2 to match with the existings including taking down the existing old one complete all as specified and as directed.

S&F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor using concrete 1:2:4 type B0 and to match with existing specifications complete all as specified and as directed. Make : Cat No. C0117 of Parryware/Hindware/Cera.

S&F in reapirs 10 litre capacity, PVC valve less syphonic duel type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets complete all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, with PVC waste pipe, CP waste coupling, chain, plug and porcelean stopper and backets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed. Make : Cat No. C0406 of Parryware/Hindware/Cera.

S&F in repairs 15 mm bore, pillar taps, cast copper alloy, chromium plated, fancy type, with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15 mm bore, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F for 15mm bore, PVC connection pipe 600mm long with PTMT nuts at both ends complete all as specified and as directed.

S&F in repairs 15 mm bore, stop valves, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

S&F in repairs 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints fixed to wall, using MS holder bat etc complete all as specified and as directed.

S&F in repairs 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints, laid in trenches or in floors, etc complete all as specified and as directed.

S&F in repairs 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints fixed to wall, using MS holder bat etc complete all as specified and as directed.

S&F in repairs 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with rubber ring joints, laid in trenches or in floors, etc complete all as specified and as directed.

S&F for 75 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends of any radius complete all as specified and as directed.

S&F in repairs 75 mm bore, PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) junction single (Single T) equal or unequal with access door complete all as specified and as directed.

S&F for 110 mm bore, PVC (SWR) bends with acess door of any radius complete all as specified and as directed.

S&F in repairs swival shower of PTMT 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and as directed.

S&F for 12mm prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination and fixed with screws to timber frame work complete all as specified and as directed.

Supply and install the diving spring board made of special wood and laminated in FRP using 99.7% water resistant polyster resin compositetly reinforced with CSM-450 chopped glass stand material and moulded with anti slippery top laminated with WR-300 mat with thickness 2.5" to 1.5" and width 20" tappered from one end to other size 0.5 MW + 4.80 ML, suitable for diving use, complete fixing with bracket and machenical fulerum unit suitable for 1 mtr, 3 mtr and 5 mtr diving use: (i) Diving board height ( 1mtr and 3 mtr ), lenght= 12 feet (ii) Diving board height ( 5 mtr ), lenght= 16 feet

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power), (fitting such as switches, ceiling roses, pendants, regulators, sockets, etc to be measured separately), removing materials to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

M&L for concealed point wiring with 1.5 Sqmm (nominal area), FR-LSH PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including PVC conduit with all fittings and accessories of PVC conduit (like Tee, bend etc.) complete with and including 1.5 Sqmm (nominal area) FR-LSH PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point terminated in metal flush box of suitable size for mounting switches, sockets, regulators etc including cutting chases and making good by using cement mortar (1:4) complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and as directed.

All as per item No 121 above but for one 3 pin socket outlet, 6 Amps on independent board complete all as specified and directed.

All as per item No 121 above but for one 6 Amps, 3/5 pin socket outlet on same board with other switches complete all as specified and as directed.

All as per item No. 121 above but wiring with cables of size 2.5 sqmm and cables of size 2.5 sqmm as continuous earth wire for one 6/16 Amps switch socket combination on Independent board complete all as specified and as directed.

S&F for switch piano, 6 Amp single pole, flush type one way 230 volts bearing ISI marked complete all as specified and as directed.

S&F for socket outlet, 2 in 1, 3 pin, 6 Amps, flush type bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 6 Amps, flush type, 240 volts bearing ISI marked complete all as specified and as directed.

S&F for switch socket combination, 2 in 1, 6/16 Amps, 240 volts, bearing ISI marked flush type complete all as specified and as directed.

S&F for ceiling rose, 3 phase/PVC/polycarbonate, isolated body bearing ISI marked and including PVC box complete all as specified and as directed.

S&F for stepped type(five steps) electronic fan regulator flush type complete all as specified and as directed. Make : Model No. 14502 of Anchoror or equivalent.

S&F in repairs 18 Watt surface and wall mounting type LED batten with polycarbonate housing and integrated complete all as specified and as directed. Make : Havells/Philips/Bajaj/CG/Wipro.

S&F in repairs 9 Watt surface and wall mounting type LED batten with polycarbonate housing and integrated complete all as specified and as directed. Make : Havells/Philips/Bajaj/CG/Wipro.

S&F in repairs LED post top lantern of 25 Watt made in cast aluminium spigot housing with decorative opal acrylic diffuser and IP65 protection, including 40 Watt MH/SV lamp including providing and connection with 1.5Sqmm copper conductor, multistranded copper conductor cable of required length complete all as specified and as directed. Make : Model APBY025C0875 of Century/Havell's/ Philips/CG.

S&F for underwater LED light fitting power consuption 3 watt, diecast aliminium lamp body, power coating finishing IP68 color temperature 3000 k, thermal conductivity more than 2.0 W/mk and thermal pad with thermal conductivity more than 1.5 W/mk including all necessary connection and fixing arrengment complete all as specified and as directed.

S&F for PVC insulated, sheathed, flat stranded copper conductor of 4 Sqmm, 3 core, water proof submersible cable and fixed in submersible pump to starter complete all as specified and as directed.

S&F for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

S&F for LED lamp 9 Watt complete all as specified and as directed. Make : Havells /Philips/Bajaj /Surya.

S&F in repairs factory made board distribution (DB) double door in sheet steel enclosure with common bus bar at incomming end bus bar, TPN, 4 way, 415 Volts suitable for fixing MCBs complete all as specified and as directed.

S&F in repairs factory made board distribution (DB) double door in sheet steel enclosure with common bus bar at incomming end, SPN, 8 way, 240 Volts suitable for housing MCBs complete all as specified and as directed.

S&F for MCB, SPN, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed. Make: Cat No. 408609 to 408617 of Legrand or equivalent.

S&F for MCB, 'C' Series, SP, 240 Volts, 6 to 32 Amps, 'C' Series, 10KA capacity complete all as specified and as directed. Make: Cat No. 408587 to 408595 of Legrand or equivalent.

S&F for MCB, 'C' Series, TPN, 240 Volts, 63 Amps, 'C' Series, 10KA capacity complete all as specified and as directed. Make : HPL/L&T/Havells.

S&F for sheet metal enclosure, single pole and neutral with two pin and earth plug complete with one single pole MCB, 20 Amps, 240 volts complete all as specified and as directed. Make : Havell's/L&T/Siemens/HPL/Standard/Legrand.

S&F in repairs sheet steel enclosure suitable for fixing MCB, TPN, 4 way, 415 Volts, double door, IP 54 protection, three phase, complete all as specified and as directed.

S&F in repairs MCCB, 4 pole, 415 V with fixed thermal & fixed magnetic setting, 160 Amps of breaking capacity 25 KA, 415 Volts, complete all as specified and as directed. Make:Cat No. 4200 15 of Legrand or equivelant.

Taking down unserviceable sub-main wiring up to 10 sqmm with rigid steel conduits/PVC casing-caping including cutting chases for taking out conduits and making good disturbed surfaces complete all as specified and as directed.

M&L for concealed sub main wiring with two runs of single core 4 sqmm PVC insulated , unsheathed multistranded copper conductor 1100 volts FRLSH cable , including one run of 4 sqmm single core PVC insulated unsheathed multistranded copper conductor 1100 volts FRLSH cable as earth continuity drawn through and including one run of PVC conduit heavy duty and connected accessories etc and connecting to common earth dolly complete all as specified and as directed. Note : Two runs of main cable,one run of earth continuity conductor cable and one run of PVC conduit will be measured as one unit for payment purpose.

M&L for concealed sub main wiring comprising single core, 2 Runs of 6 sqmm nominal cross sectional area, FR-LSH multistranded copper conductor cable as per IS 694:2010, ISI marked, annealed, multistranded copper conduct drawn through and including medium mechanical stress class PVC conduit as per IS 9537:(Part-III) : 1983 of suitable size as per required at site dia but not less than 20 mm nominal size including provision of 1X6 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire complete all as specified and as directed. Make : Finolex/KEI/Havells for Copper cable and Make : Prestoplast/Plaza for conduit and accessories. Note : 1. Extra length of cables/ wire required for connection to MCBs/DB's shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly 2. Cost of cutting chase and making good shall be included in the quoted rate.

M&L for concealed submain wiring comprising single core ,4 Runs of 10 sqmm nominal cross sectional area,FR-LSH multistranded copper conductor cable as per IS 694:2010,ISI marked ,annealed,multistranded copper conduct drawn through and including medium mechanical stress class pvc conduit as per IS 9537:(Part-III) : 1983 of suitable size as per required at site dia but not less than 20 mm nominal size including provision of 2X10 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire complete all as specified and as directed. (Make- Finolex/KEI/Havells for Copper cable and Make- Prestoplast/Plaza for conduit and accessories). ( Note :- (1) Extra length of cables/ wire required for connection to MCBs/DB's shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly). (2)Cost of cutting chase and making good shall be included in the quoted rate.

M&L for concealed submain wiring comprising single core , 2 Runs of 10 sqmm nominal cross sectional area,FR-LSH multistranded copper conductor cable as per IS 694:2010,ISI marked ,annealed, multistranded copper conductot drawn through and including medium mechanical stress class pvc conduit as per IS 9537:(Part-III) : 1983 of suitable size as per required at site dia but not less than 20 mm nominal size including provision of 1X10 sqmm nominal cross sectional area multistranded copper conductor cable, PVC insulated unsheathed 1100 Volts grade as earth wire complete incl taking down old UNSV sub main all as specified. Make : Finolex/KEI/Havells for Copper cable and Make : Prestoplast/Plaza for conduit and accessories. Note : 1. Extra length of cables/ wire required for connection to MCBs/DB's shall not be measured and the rate quoted by contractor for per unit shall be deemed accordingly. 2. Cost of cutting chase and making good shall be included in the quoted rate.

S&F for 25 Watt building security light (INDUS SERIES OF C&S) new generation energy saving and environtal friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having TOP OPENING separate driver compartment with IP65 protection and impact resistance of IK07, including taking down of old unservicible one complete all as specified and as directed. Make: Cat No. LTESS25WLED/LS of C&S or equivelant.

M&L for earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers,necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing complete complete all as specified and as directed.

M&L for sand cushioning with dry clean sand 15cm below cable and 8cm above the cable complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

M&L for bricks laid in trenches for LT cable protection with length of brick perpendicular to length of cable complete all as specified and as directed.

M&L for 32 mm bore, steel tubes, galvanised, light grade with all fittings, laid in floor/road crossing/drain etc as in UG cable protection complete to walls and ceilings or laid in floors complete all as specified and as directed.

Boring hole below the road for pipe crossing upto 100mm bore, using trenchless technology complete all as specified and as directed. Note : Cost of accessories required for making hole/bore deemed to be included in the quoted rate.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, 2 core, nominal cross sectional area of main conductor 6 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI Pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, armoured, 2 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI Pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, armoured cable for working voltage of 1100 Volts, PVC insulated, armoured, 3 core with reduced neutral conductor (3 1/2 Core), nominal cross sectional area of main conductor 50 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI Pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items of this schedule. (2) Excvation and earth work shall be measured and paid seperately.

S&F for earth continuity conductor or main earthing lead with galvanised iron wire 4mm dia, fixed to wall on batten or recesses or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc, as required complete all as specified and as directed.

S&F for modular junction box made of SMC/FRP of size 140x140x95mm with provision of MCB SP, 6-32A, 10 KA, 'C' Curve, 01 No and connector terminal 4 pole indicating RYB Phase Colour and Neutral colour complete fixed to street light pole with suitable size of mild steel clamps, nuts & bolts complete all as specified and as directed. Make : CAT No : GSJB 1414 of Syntex or equivalent.

M&L for taking down old unserviceable and test point terminal box made of gun metal or phosphorous bronze,size 75x75x25 mm, drilled and screwed including 03 Nos 8mm dia 25 mm long hexagonal head screwed including removing the existing old unsv one complete all as specified and as directed.

S&F in repair Off load Change over switch, 200 Amps, 4 pole, 415 V, 50 Hz, fully compacted in 1.6mm thick CRCA sheet enclosure and direct mounted & front operated type, manually operated, alongwith all necessary accessories and fixing arrengment M&L for Make :Cat part :OFFPE0200 of Indo Asian /HPL/Havells/L&T.

Supply, installing, testing and commissioning of heavy duty Turboforce Exhaust fan, suitable for Single Phase AC supply, earthing etc, 220/240 V, 450 mm sweep size, fan speed 1400 RPM, 4 nos. aerodynamically designed metallic blades, copper winding, Air delivery minimum 6200 cum mtr/hr, minimum noise level & vibration free and including all fixing accessories M&L for Make : Model No: FHEHDTPDB180of Havells/ Bajaj/Khaitan/Cromption.

Supply, installing, testing and commissioning of heavy duty Turboforce Exhaust fan, suitable for Single Phase AC supply, earthing etc, 220/240 V, 380 mm sweep size, fan speed 1400 RPM, 4 nos. aerodynamically designed metallic blades, copper winding, Air delivery minimum 3700 cum mtr/hr, minimum less noise level & vibration free and including all fixing accessories M&L for Make : Model No Turbo Forces SP of Havells/ Bajaj/Khaitan/Cromption.

Supply, installing, testing and commissioning of heavy duty Wall Fan, suitable for Single Phase AC supply, earthing etc, 220/240 V, 450 mm sweep size, fan speed 1440 RPM, 3 nos. aerodynamically designed metallic blades, copper winding, Air delivery minimum 150 cum mtr/hr, oscillation type (upto 60 degree), minimum noise level & vibration free and including all fixing accessories M&L for Make : Model No V3 of havells/Bajaj/Khaitan/Cromption.

Supply, installing, testing and commissioning of heavy duty Wall Fan, suitable for Single Phase AC supply, earthing etc, 220/240 V, 300 mm sweep size, fan speed 1400 RPM, 3 nos. aerodynamically designed metallic blades, copper winding, oscillation type (upto 60 degree), minimum noise level & vibration free and including all fixing accessories M&L for Make : Havells/Bajaj/Khaitan/Cromption.

M/S CHANDAN ENTERPRISE

Garg Brothers

M/S. NOBIN RAJKHOWA

M H KHAN