SPL REPAIR OF BLDG NO SP 202 AT IN SUKNA MIL STN AND CERTAIN OTHER SANCTIONED WORKS IN SUKNA MIL STN UNDER GE SUKNA

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in Soft/ Loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Excavating post holes or similar holes, each not exceeding 0.5 Cum, getting out in Soft/ Loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and directed.

M & L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Removing Excavated soils not exc 50 M and depositing where directed at a level not exc1.5 M above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, similar bands, plinth coarses, string coarses, lacing coarces, parapets nad railings upto 60 cm in height, filling in pressed steel door complete all as specified and directed.

M&L for RCC M-25 (Design Mix) as in foundation including rafts, footings, foundation beams, plinth beams, bases of columns etc basement slabs reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) as in chajjas complete all as specified and directed including necessary formwork rounded or chamfered on edges complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded stone as in beams, cantilevers, bressummers, lintels over 1.5m clear span complete all as specified and directed.

M&L for Reinforced Cement Concrete M-25 (Design Mix) using 20 mm graded stone as in columns, pillars, piers, posts and struts complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for 40 mm thick Damp proof course to horizontal or vertical surfaces including necessary form work in cement concrete 1:2:4 type B-0 (Using 12.5 mm graded stone aggregate) complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed .

M&L 18-20 mm thick granite slab(of any type) tiles machine cut, bedded jointed with grey/ colored cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone as in cladding, jambs, cills, including grinding and polishing complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

S&F 40 mm thick factory made flush door shutter solid core construction, with particle board core and plywood face panels,commercial type on both side complete all as specied and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on solid PVC wall lining, insulated PVC Wall lining, and solid PVC partitions inclusive of solvent cement and fixing at site complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 75 mm long medium weight, cold rolled mild steel Butt hinges with screws complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges with screws complete all as specified and directed.

S&F 150 mm Aluminium handles cast type, anodised and fixed complete all as specified and directed.

S&F in repairs mortice locks suitable for aluminium door of 100 mm size 4 lever aluminium body vertical type as per existing or sample complete all as specified and directed.

Supply & fix as in repair 28mm dia curtain harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. with two Nos of socket ,end caps and brakets (decorative type) complete for doors/window opening all as specified and directed.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S & F in repairs Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples including wooden beads complete all as specified and directed.

M&L powder coated Aluminium door, window, Cup board and ventilator shutter and frame any type (Sliding or openable ) with frame and other similar work, fabricated aluminium mesh etc. aluminium heavy section favricated incl all necessary roller wheels, cleats, handle, locking arrangement and arrangement to fix wire mesh with aluminium channel beading and stainless steel screw incl cost of rubber gasket ,beading roller wheel etc. ,complete all as specified and directed. Note: (a) The weight of rubber gasket beading, roller wheels, etc will not be measured with the weight of aluminium shutters as only aluminium items shall be measure. (b) Wire mesh shall be measured and paid separately. (c) Aluminium hinges shall be included in the unit rate

Supply and fixing factory made uPVC white colour three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Cont..,

Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc.

Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in- Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

M&L rolled mild steel conforming to Fe 290 (Gde E-165), in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) and including distance pieces, cleats etc. complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F 4 mm thick E-board (designer pattern) celing of size 60x60 cm, fixed or laid / inserted to aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including anodised aluminium snap grid frame work for false ceiling hanging from structural steel / scantling with 6 mm GI wire complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) as in plinth protection, sub base, floors, paths, hardstanding, path and pavings, etc. finished even and fair without using extra cement complete all as specified and directed.

M&L for 75 mm thick cement concrete, type B2, 1:2:4 (using 40 mm graded stone aggregate) as in paving, hardstanding, path etc, flooring and finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L 100 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base finished even and rough complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) laid above PCC sub floor / correction layer /under layer complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 8-10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:3 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm in cement mortar 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 fnished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

M & L for 15 mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or stone masonry or on one side of lathing surfaces and finished the surface even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of new plastered wall surfaces and including applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L complete removal of existing treatment of old decorated ceiling surfaces and including applying two coats of oil bound distemper complete all as specified and directed.

M&L preparation of old plastered wall surfaces and inlcuding applying one coat of weather coat acrylic exterior emulsion paint complete all as specified and directed.

M&L preparation of new plastered wall surfaces and finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @2.20kg / 10 sqmm and providing and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed.

S&F 4 mm thick plain sheet glass ordinary quality fixed with aluminium frame work not exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4 mm thick glass including tinted / dark film / heat absorbing glass of any size each pane complete fixed to UPVC / aluminium frame work including rubber beading complete all as specified and directed.

S&F 5 mm thick glass including tinted / dark film / heat absorbing glass of any size each pane complete fixed to UPVC / aluminium frame work including rubber beading complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs Decorative corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, and side not less than 225 mm with chromium plate bracket guard complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of old painted wood and wood based surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors including taking up or down complete all as specified and directed.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, two way, fancy type chromium plated, cast copper alloy, with crutch or butterfly handle and wall flange, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for hot water supply complete all as specified and directed.

S&F in repair stainless steel towel rail 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S&F in repair Towel ring chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat (Minimum weight 90 gms) complete all as specified and directed.

S&F in repairs EWC Rimless single piece WC with UF soft close seat cover, hinges, dual flush cistern fitting, fixing accessories and accessories set size 360 x 675 x 750 mm complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S&F in repairs swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repairs 15 mm bore dia brass chromium plated 3-in-1 wall mixer for mixing hot & cold water screwed down for iron pipe and fixed shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour (Minimum weight 40gms) complete all as specified and directed.

S&F in repair brass chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and as directed.

S&F as in repair Health faucet of CP 15mm bore fancy type with suitable flexible pipe as per site requirement incl CP nipple with socket complete all as specified and directed by Engr-in-Charge.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch and including cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed.

All as per Sl. item No. 116.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 116.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 119.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 119.00 above but for one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 119.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

S&F switch piano flush type single pole one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F switch socket combination 3 pin 15 Amp, flush type universal complete all as specified and directed.

S&F switch socket combination 5 pin 6 Amp, flush type universal complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F in repairs MCB SPN 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB ,SPN DB, 08 ways double door,Metal door, IP-43 IK 09 in 200A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F angular type lamp holder, PVC/Polycarbonate type with back plate suitable for Led lamp complete all as directed.

S&F stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type, white 120 W - 2 module 240Volts complete all as specified and directed.

M & L of Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

Supply and fix in repair of energy saving 1200 mm sweep BLDC ceiling fan complete with all connected accessories as specified below: - Input Power :- 26 watts with full speed and reduced power consumption with reduced speed technology. Voltage :- 90-300 V AC, 50Hz, single Phase. RPM :- 340 to 375 rpm Blades :- Decorated Sweep :- 1200 mm. Air delivery :- Not less than 210 CFM Colour :- Glow white/Toast Brown/Gloss Black/or others as approved by Engr-in-Charge Speed/power contro :- Without Remote through existing regulator Star rating :- BEE 5 Star Rating Warranty: - As specified by the manufacturer, contractor shall produce original warranty and test certificate from the manufacturer.

S & F LED bulb 9 Watt for fixing in decorative wall lights complete all as specified and as directed.

S&F in repairs LED battery backup inverter bulb of Lamp wattage: - 12 Watts, Battery: - Not less than 2200mAh or not less than 4 hrs backup,Efficeacy: - Not less than 110 Lm/Watt including taking down old unsv ones complete all as specified and directed.

S & F Light fittting 1 x 20 watt ,220 V AC PVC box type with driver, holder including LED tube light connecting up with three core flexible copper cableof suitable size complete all as specified and as directed.

S & F LED Street Light 20 watt made up of pressure die cast aluminiun housing with highly efficient LEDs and PC cover with integrated lens with IP66, IK07, System Lumen Efficasy =100 Lm/W, 5 kV Surge Voltage Protection,Operating Voltage range 140 V - 270 V and bracket suitable for street light made out of GI pipe light grade of 25 mm bore & 0.75 mtr length (minimum), bend to shape including 2 pairs of MS flat iron clamps made out of 40 x 5 mm MS flat, nuts, bolts & washers etc, & painting the bracket with two coat of aluminium paint over a coat of red oxide primer complete all as specified and as directed.

Supply and fixing in repair of LED lights fitting 1x 15W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply and fixing in replacement LED bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including taking down old unsv complete all as specified and as directed.

S&F in repairs 32 mm dia GI tubing light grade bracket over all 1.2 mtr length bent to shape 120 degree with cutting as required and bend to shape with flat iron clamp of size 32x6 mm, 2 Nos, suitable size of nut bolts and washers complete for fixing street light fittings on electric poles/bldgs for security complete all as specified and directed.Make:Nezone/Surya/Jindal poles

S&F in repairs of LED 36 Watt Versatile 2'x2' recess mounted liminaires which suites various ceiling types 35 mm depth with tapered housing makes is most flexible to install in low clearance ceiling with high performance multi layer optics-primary (Individual lens on LEDs) & secondary (preismatic & opal diffuser) to ensure homogenous uniform lighting distribution with UGR<19 compliance all as specified & as directed. Make :- HAvells Model No PLANO TAPS UGR 19 Cat Part No PLANO2X2PLR36WLED830TAPSUGR19)

S&F in repairs of LED Decorative wall light,stainless steel,rust free fixture with white glass diffuser suitable for 7.5W LED filament lamp E27 base,incl LED lamp complete all as specified & as directed.Make :- Havells Model No FLORETTE WL 1LS E27 SS Cat Part No LHFOAID1TZ1I040)

S&F in repairs of LED bed side table lamp to brighten up your room in style with a wide variety of style, shapes & colors best suitable for 7.5W A60 LED filament lamp with E27 base, incl LED lamp complete all as specified & as directed.Make :-Havells Model FAIRY TALE,CAt PArt No LHFHAODBTN1X007

Supply and fixing in repair of single Pole & Neutral enclosure with 2 pin and earth plug & socket for incorporating with single pole 20 Amp MCB all as complete including taking down old unsv one and directed by the Engineer-in-charge.

Taking down old unseviceable DB/TPN DB any size and any capacity including MCB/RCB/Isolator complete all as specified and as directed.

Supply and fixing of MCB TPN DB 4 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge.

Supply and fixing of 415V 10KA 'C' series miniature circuit breaker (MCB) TPN 63 Amps current carrying capacity incl taking down old unsv complete all as specified.

Supply and fixing of MCB SPN DB 8 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge.

Supply and fixing of MCB SPN DB 4 way double door,IP-43 protection,isolated neutral bar,insulated busbar assembly,mechanical impact strength of IK08 complete all as specified and directed by Engr-in-charge.

S&F PVC non metallic rigid conduit not less than 20 mm dia with its conduit accessories concealed on floor/wall/surface on ceiling with suitable clamps/saddles rigid non metallic PVC conduit exclusive boxes (junction/terminal) but inclusive of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles, pipe hooks etc complete all as specified and directed.

Taking down sub main wiring any description along with PVC conduit/casing capping/wooden batten/metal conduit and make good the disturbed surface all as specified.

Material & labour for Sub main wiring with two runs of single core 4 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 4 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 6 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 6 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed.

Material & labour for Sub main wiring with two runs of single core 10 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 1 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 10 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed.

Material & labour for Sub main wiring with four runs of single core 10 Sqmm (Nominal Area) FRLSH PVC insulated and unsheathed multi standed copper conductor cable LT 1100 volts grade drawn thorugh and including PVC concealed conduit medium grade of adequate size fixed on surface of wall/ceiling with all necessary fittings and accessories and 2 run of FRLSH PVC insulated and unsheathed insulated single core cable with multi standered copper conductor of size 10 Sqmm as earth wire (green in colour) run through PVC concealed conduit and connected common earth dolly including taking out the old sub main wiring for connection to DBs/dolly shall be deemed to be included in this item and shall be measured as one run complete all as specified and directed.

Supply,installaing,testing & commissioning of factory made (CPRI Approved) LT indoor Panel,AC, 415 volt,50 Hz,3 Phase,4 wire of size 1200mmx1300mmx350mm designed following form 4b separator panel rules for protection from interior live components,totally enclosed self supporting structure/cubical openable at the front & back,with bottom cable entry and exit; structure made out of 2 mm thick CRCA steel sheet with U channel Iron base of ISA-75x40x5 mm.The components doors should be provided with the name plates giving feeder description for permanent identification.All doors must be provided with Tri functional (Functional as a sealant,elastic in nature and non water absorbent) gasket to make the panel dust and vermin proof.All doors must be welded at the joints and should have smooth corner bends.Fan filters/outlet filters with hood must be provided at the ventilation.Cable alley should be provided for all outgoing connections accessories prewired with suitable size FRLSH PVC insulated multistranded copper conductor.Wiring should be complete with sockets and ferrule marking for every cnnection.Brass glands should be provided at the inlet and outlet cable points.Danger board on front and rear sides of the panel should be provided.Structure painted with textured powder coated paint of thickness not less than 100 microns after preparation of surface in 8 tank sheet process system.

M&L for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron GI strip of size 32x6 sqmm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth strip protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion including dismantaling old unsv ones complete all as specified and as directed by the Engineer-in-Charge.

ASHISH ROY (BID ID -3249628)

SHANTI UDYOG (BID ID -3250229)

M/s B. K. Ghosh and Co. (BID ID -3249619)

M/S JAGRITI ENTERPRISES (BID ID -3249749)

M/S EASTERN ENGINEERING (BID ID -3250155)

ELECTRO WIR WAY (BID ID -3249617)

A K ENTERPRISES (BID ID -3249882)

VICKY ENTERPRISES (BID ID -3249691)