Construction of Boys and Girls Hostel and Male and Female Technician Accommodation at SMVDIME Kakryal, Katra, UT of J and K on PMC mode

S. NO. DESCRIPTION AMOUNT ( DSR ) AMOUNT (NON-DSR)

1 STRUCTURE WORK

CONCRETE WORK Rs. 19,33,233.53 Rs. 0.00 Rs. 19,33,233.53

REINFORCED CEMENT CONCRETE Rs. 24,39,99,527.15 Rs. 0.00 Rs. 24,39,99,527.15

MARBLE & GRANITE WORK Rs. 86,28,190.62 Rs. 0.00 Rs. 86,28,190.62

3 ELECTRICAL WORKS

SUBSTATION EQUIPMENTS Rs. 0.00 Rs. 18,67,785.80 Rs. 18,67,785.80

EARTHING INSTALLATION Rs. 0.00 Rs. 26,62,808.00 Rs. 26,62,808.00

LT CUM DG CHANGE OVER PANEL, MAIN DISTRIBUTION

EARTHING AND LIGHTINING PROTECTION INSTALLATION Rs. 11,92,415.36 Rs. 0.00 Rs. 11,92,415.36

WIRING IN STEEL AND PVC CONDUIT Rs. 93,60,425.60 Rs. 0.00 Rs. 93,60,425.60

LIGHTING FIXTURE AND FANS Rs. 0.00 Rs. 1,88,37,910.00 Rs. 1,88,37,910.00

EXTERNAL LIGHTING SYSTEM Rs. 0.00 Rs. 14,85,808.00 Rs. 14,85,808.00

FIRE ALARM SYSTEM Rs. 18,67,822.00 Rs. 13,800.00 Rs. 18,81,622.00

PUBLIC ADDRESS SYSTEM Rs. 5,28,740.00 Rs. 3,57,569.06 Rs. 8,86,309.06

CCTV (IP VIDEO SURVEILLANCE) SYSTEM Rs. 4,09,360.00 Rs. 54,17,120.00 Rs. 58,26,480.00

DATA , VOICE SYSTEMS Rs. 42,180.00 Rs. 52,936.00 Rs. 95,116.00

SMOKE EXTRACTION SYSTEM Rs. 0.00 Rs. 14,58,192.00 Rs. 14,58,192.00

SANITARY FIXTURES & FITTINGS Rs. 61,78,382.35 Rs. 5,35,600.00 Rs. 67,13,982.35

INTERNAL & EXTERNAL WATER SUPPLY Rs. 26,68,722.38 Rs. 3,26,528.00 Rs. 29,95,250.38

SOIL, WASTE, VENT PIPES & FITTINGS FOR INTERNAL Rs. 7,06,296.80 Rs. 8,14,236.00 Rs. 15,20,532.80

STROM WATER PIPES & FITTINGS Rs. 8,41,513.40 Rs. 7,10,466.00 Rs. 15,51,979.40

EXTERNAL SEWERAGE SYSTEM Rs. 5,26,299.20 Rs. 4,57,490.38 Rs. 9,83,789.58

5 FIRE FIGHTING

FIRE PUMP & PIPE & ACESSERIES Rs. 19,48,249.00 Rs. 9,49,000.00 Rs. 28,97,249.00

Multiplication factor for modified Analysis of Rate @0.973 on

Grand Total (DSR+NDSR) Rs. 48,28,90,399.61

Grand Total (DSR+NDSR) Rs. 48,28,90,399.61

TOTAL COST OF BOQ (DSR/NON DSR) Rs. 48,28,90,400.00

Digitally signed by ANUJ

Construction of Boys & Girls Hostel and Male& Female Technician Accommodation at SMVDIME Kakryal, Katra, UT

BILL OF QUANTITY

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Earth work in excavation by mechanical means (Hydraulic excavator)

over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10

2.6 sqm on plan) including getting out and disposal of excavated earth

lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up

to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including

watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery

2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% Litre 501.16 234.75 117647.31

Diluting and injecting chemical emulsion for PRE

2.35 CONSTRUCTIONAL anti-termite treatment (excluding the cost of

chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @

one litre per hole, 300 mm apart including drilling 12 mm diameter

holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse

sand) to match the existing floor:

2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration Sqm 2004.64 310.05 621538.63

4 CONCRETE WORK

Providing and laying in position cement concrete of specified grade

4.1 excluding the cost of centering and shuttering - All work up to plinth

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural

4.1.8 sources : 8 graded stone aggregate 40 mm nominal size derived Cum 225.38 6812.00 1535292.74

from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1

cement : 3 coarse sand (zone-III) derived from natural sources : 6

graded stone aggregate 20 mm nominal size derived from natural

4.17 sources) over 75mm thick bed of dry brick ballast 40 mm nominal Sqm 531.08 749.30 397940.79

size, well rammed and consolidated and grouted with fine sand,

including necessary excavation, levelling & dressing & finishing the

5 REINFORCED CEMENT CONCRETE

Centering and shuttering including strutting, propping etc. and

removal of form for

5.9.1 Foundations, footings, bases of columns, etc. for mass concrete Sqm 5569.20 392.15 2183961.78

Walls (any thickness) including attached pilasters, butteresses, plinth

and string courses etc.

5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 18753.71 927.25 17389379.98

5.9.4 Shelves (Cast in situ) Sqm 256.02 927.25 237394.55

5.9.5 Lintels, floor beams, girders, bressumers and cantilevers Sqm 14506.33 736.40 10682462.56

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 9270.35 961.30 8911588.99

5.9.7 Stairs, (excluding landings) except spiral-staircases Sqm 1131.08 208.55 235886.75

5.9.16 Edges of slabs and breaks in floors and walls

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Steel reinforcement for R.C.C. work including straightening, cutting,

5.22 bending, placing in position and binding all complete upto plinth level.

5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 271849.44 107.85 29318962.57

Steel reinforcement for R.C.C. work including straightening, cutting,

5.22A bending, placing in position and binding all complete above plinth

5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 863399.31 107.85 93117615.12

Providing and laying in position ready mixed or site batched design

mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources,

Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to

5.33 accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete

to site of laying, curing, carriage for all leads; but excluding the cost of

centering, shuttering, finishing and reinforcement as per direction of

the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement

content in design mix shall be payable separately. In case the

cement content in design mix is more than 110% of the specified

minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

5.33.2 All works above plinth level.

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Add for using extra cement in the items of design Mix over ans avove

the specified cement content therein

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each

four floors or part thereof.

Total Structural Work 248006974.73 0.00

6.0 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of

class designation 7.5 in foundation and plinth in:

6.1.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 40.00 7132.25 285290.00

Brick work with common burnt clay F.P.S. (non modular) bricks of

6.4 class designation 7.5 in superstructure above plinth level up to floor

V level in all shapes and sizes in :

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) Cum 321.26 9105.95 2925355.69

Half brick masonry with common burnt clay F.P.S. (non modular)

6.12 bricks of class designation 7.5 in foundations and plinth in :

6.12.2 Cement mortar 1:4 (1 cement : 4 coarse sand) Sqm 40.00 905.05 36202.00

Half brick masonry with common burnt clay F.P.S. (non modular)

6.13 bricks of class designation 7.5 in superstructure above plinth level up

to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm. 334.74 1123.80 376181.32

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars

at every third course of half brick masonry.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and laying autoclaved aerated cement blocks masonry with

100/125 mm thick AAC blocks in super structure above plinth level

6.38 up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). Cum 600.42 10195.45 6121514.83

The rate includes providing and placing in position 2 Nos 6 mm dia

M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with

150mm/230mm/300 mm thick AAC blocks in super structure above

plinth level up to floor V level with RCC band at sill level and lintel

6.47 level with approved block laying polymer modified adhesive mortar all Cum 1961.08 8333.65 16342980.74

complete as per direction of Engineer-in-Charge. (The payment of

RCC band and reinforcement shall be made for seperately).

8.0 MARBLE & GRANITE WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished,

premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations of required

size, approved shade, colour and texture laid over 20 mm thick base

8.2 cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with

white cement, mixed with matching pigment, epoxy touch ups,

including rubbing, curing, moulding and polishing of edges to give

high gloss finish etc. complete at all levels.

8.2.2 Granite stone slab of colour black, Cherry/Ruby red

Providing edge moulding to 18 mm thick marble stone counters,

Vanities etc., including machine polishing to edge to give high gloss

finish etc.complete as per design approved by Engineer-in-Charge.

8.3.2 Granite work Metre 460.93 510.95 235514.23

Extra for fixing marble /granite stone, over and above corresponding

basic item, in facia and drops of width upto 150 mm with epoxy resin

based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/

kitchen sink in kitchen platform, vanity counter and similar location in

8.5 marble/ Granite/ stone work, including necessary holes for pillar taps Each 196.00 978.70 191825.20

etc. including moulding, rubbing and polishing of cut edges etc.

Providing and fixing rubbed stone slab table, edges rounded and

polished, 75 cm high 50 cm deep and 18mm thick, fixed in urinal

partitions by cutting a chase of appropriate width with chase cutter

8.10 and embedding the stone in the chase with epoxy grout or with

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate 6 mm nominal size) as per direction of Engineer-in-charge

and finished smooth.

8.10.2 Granite Stone of approved shade Sqm 8.10 4051.85 32819.99

Providing and fixing Ist quality ceramic glazed wall tiles conforming to

IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle green,

black of any size as approved by Engineer-in-Charge, in skirting,

8.31 risers of steps and dados, over 12 mm thick bed of cement mortar Sqm 5289.84 1267.95 6707254.91

1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in white cement mixed with

pigment of matching shade complete.

9.0 WOOD & PVC WORK

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and fixing ISI marked flush door shutters conforming to IS :

2202 (Part I) nondecorative type, core of block board construction

9.21 with frame of 1st class hard wood and well matched commercial 3 ply

veneering with vertical grains or cross bands and face veneers on

both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with

necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm

9.23 minimum depth on all edges of flush door shutters (over all area of Sqm 1656.69 462.35 765970.62

door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of

9.24 flush doors (cost of glass excluded) (overall area of door shutter to

9.24.1 Rectangular or square Sqm 95.76 199.15 19070.60

Providing and fixing aluminium extruded section body tubular type

universal hydraulic door closer (having brand logo with ISi, IS : 3564,

9.84 embossed on the body, door weight upto 36 kg to 80 kg and door Each 830.00 983.15 816014.50

width from 701 mm to 1000 mm), with double speed adjustment with

necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868 )

transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium handles, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868)

transparent or dyed to required colour or shade, with necessary

screws etc. complete :

Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour and shade, with

necessary screws etc. complete.

9.101.1 Single rubber stopper Each 830.00 39.60 32868.00

Providing and fixing bright finished brass 100 mm mortice latch and

lock, ISI marked, with six levers and a pair of anodised (anodic

9.103 coating not less than grade AC 10 as per IS : 1868) aluminium lever Each 794.00 868.95 689946.30

handles of approved quality with necessary screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt/ suede finish with high density protective

9.127 surface layer and reverse side of adhesive bonding quality

conforming to IS : 2046 Type S, including cost of adhesive of

approved quality.

Providing and fixing fire resistant door frame of section 50 x 60 mm

on horizontal side & 35 x 60 mm on vertical sides having built in

rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than

120gm/sqm) suitable for mounting 120 minutes Fire Rated Glazed

Door Shutters. The frame shall be filled with mineral wool Insulation

having density minimum 96Kg/sqm . The frame will have a provision

of G.I. anchor fastners 14 nos ( 5 each on vertical style & 4 on

9.161 horizontal style of size M10 x 80 ) suitable for fixing in the opening meter 467.00 2202.9 1028754.30

along with factory made template for SS ball bearing hinges of Size

100x89x3mm for fixing of fire rated glazed shutter . The frame shall

be finished with a approved fire resistant primer or powder coating of

not less than 30 micron in desired shade as per the directions of

Engineer - in- Charge . (Cost of SS ball bearing hinges is excluded).

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and fixing 60 mm thick glazed fire resistant door shutters of

120 minutes Fire rating conforming to IS:3614 (Part II) or EN1634-

1:1999, tested and certified as per laboratory approved by Engineer-

in-Charge, with suitable mounting on door frame, consisting of

vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom

rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc

9.162 coating not less than 120gm/sqm) duly filled mineral wool insulation Sqm 204.54 12017.9 2458141.27

having density minimum 96 kg/cum and fixing with necessary

stainless steel ball bearing hinges of size 100x89x3mm of approved

make, including applying a coat of approved fire resistant primer or

powder coating not less than 30 micron etc all complete as per

direction of Engineer-in-Charge (panelling to be paid for seperately).

FIXTURES FOR FIRATED DOORS

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75

MRF-1 x 3mm complete with SS Screws ( 4 Nos per panel ) Each 456.00 340.00 155040.00

Supply & fixing SS Touch Type / PHA2000 Series SS Touch type

Panic Bar single / double leaf panic exit devices. (Required For Fire

Staircase & Lift Lobby Location Doors ) as per the directions of

Engineer-in-charge

Double Leaf Panic Bar Set Each 90.00 19500.00 1755000.00

MRF-3 Supply and Fixing of intumescent fire seal of size 10x4mm Rmt. 467.00 150.00 70050.00

MRF-4 Supply and Fixing of face mounted Smoke seal Rmt. 467.00 140.00 65380.00

Supply and Filling the gap between wall & Door frame by using

silicone sealant and Wool insulaion on both side of the door

Supply & fixing of Door Closers Size 2-5 with sliding arm BLC 605 (

Except shaft door)

MRF-7 Supply & fixing of anchor fastners of M10X120mm length. Set 126.00 90.00 11340.00

Providing and fixing factory made single extruded WPC (Wood

Polymer Composite) solid door/window/Clerestory windows & other

Frames/Chowkhat comprising of virgin PVC polymer of K value 58-

60 (Suspension Grade), calcium carbonate and natural fibers (wood

powder/ rice husk/wheat husk) and non toxic additives (maximum

toxicity index of 12 for 100 gms) fabricated with miter joints after

applying PVC solvent cement and screwed with full body threaded

star headed SS screws having minimum frame density of 750

26.86 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N

(Edge), minimum compressive strength of 58 N/mm2, modulus of

elasticity 900 N/mm2 and resistance to spread of flame of Class A

category with property of being termite/borer proof, water/moisture

proof and fire retardant and fixed in position with M.S hold

fast/lugs/SS dash fasteners of required dia and length complete as

per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash

fasteners shall be paid for separately).

Note: For WPC solid door/window frames, minus 5mm tolerance in

dimensions i.e depth and width of profile shall be acceptable.

Variation in profile dimensions on plus side shall be acceptable but

no extra payment on this account shall be made.

10.0 STEEL WORK

Steel work welded in built up sections/ framed work, including cutting,

10.25 hoisting, fixing in position and applying a priming coat of approved

steel primer using structural steel etc. as required.

In stringers, treads, landings etc. of stair cases, including use of

chequered plate wherever required, all complete

In gratings, frames, guard bar, ladder, railings, brackets, gates and

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

11.0 FLOORING WORK

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregate) finished with a floating coat of neat cement,

including cement slurry, but excluding the cost of nosing of steps etc.

11.3.1 40 mm thick with 20 mm nominal size stone aggregate Sqm 20.00 614.20 12284.00

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1

11.6 cement : 3 coarse sand), finished with a floating coat of neat cement.

Kota stone slab flooring over 20 mm (average) thick base laid over

and jointed with grey cement slurry mixed with pigment to match the

11.26 shade of the slab, including rubbing and polishing complete with

base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and

pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3

11.27 coarse sand) and jointed with grey cement slurry mixed with pigment Sqm 411.85 2354.70 969777.88

to match the shade of the slabs, including rubbing and polishing

11.24 Extra for pre finished nosing to treads of steps of marble stone. Meter 1536.00 719.90 1105766.40

Extra for marble stone flooring in treads of steps and risers using

single length up to 2.00 metre.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm

(thickness to be specified by the manufacturer) of 1st quality

conforming to IS : 15622 of approved make in colours such as

11.37 White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement Sqm 1435.40 1096.55 1573985.02

mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement

slurry @ 3.3 kg/sqm including pointing the joints with white cement

and matching pigment etc., complete

Providing & Laying vitrified floor tiles in different sizes ( thickness to

be specified by the manufacturer) with water absorption's less than

0.08% and confirming to IS : 15622 of approved make in all colours

and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4

coarse sand) including grouting the joints with white cement and

matching pigments etc, complete.

Providing and laying Vitrified tiles in different sizes (thickness to be

specified by manufacturer), with water absorption less than 0.08 %

and conforming to I.S. 15622, of approved make, in all colours &

11.46 shade, in skirting, riser of steps, over 12 mm thick bed of cement

mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with

white cement & matching pigments etc. complete..

Grouting the joints of flooring tiles having joints of 3 mm width, using

epoxy grout mix of 0.70 kg of organic coated filler of desired shade

11.48.2 (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / Sqm 9801.63 309.05 3029194.93

grouting and finishing complete as per direction of Engineer-

incharge. Size of Tile 600x600 mm

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 stone aggregate 10 mm and down gauge), including

finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per

standard design :

Making khurras 45x45 cm with average minimum thickness of 5 cm

cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone

aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400

micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse

sand) and a coat of neat cement, rounding the edges and making

and finishing the outlet complete.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm

x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70

and initial emittance > 0.75 on waterproof and sloped surface of

terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1

12.55 cement : 4 coarse sand) and grouting the joints with mix of white Sqm 1936.39 1703.95 3299511.74

cement & marble powder in ratio of 1:1, including rubbing and

polishing of the surface upto 3 cuts complete, including providing

skirting upto 150 mm height along the parapet walls in the same

13.0 FINISHING WORK

13.4 12 mm cement plaster of mix :

15 mm cement plaster on rough side of single or half brick wall of

13.6 20 mm cement plaster of mix :

13.16 6 mm cement plaster of mix :

Extra for plastering exterior walls of height more than 10 m from

ground level for every additional height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over

13.26 plastered surface toprepare the surface even and smooth complete. Sqm 10459.90 262.70 2747814.91

Distempering with 1st quality acrylic distemper (ready mixed) having

VOC content less than 50 gram/litre, of approved manufacturer and

of required shade and colour all complete to achieve even shade and

New work (two or more coats) over and including water thinnable

13.41.1 priming coat with cement primer having VOC content less than 50 Sqm 5110.75 185.65 948810.25

13.45 Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and

13.45.1 including priming coat of exterior primer applied @ 2.20kg/10 sqm Sqm 13303.53 223.60 2974668.28

Painting with synthetic enamel paint of approved brand and

anufacture to give an even shade :

13.61.1 Two or more coats on new work Sqm 78.19 155.90 12189.46

Providing and applying white cement based putty of average

thickness 1 mm, of approved brand and manufacturer, over the

plastered wall surface to prepare the surface even and smooth

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50

13.82 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and

21.0 ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators

and partitions with extruded built up standard tubular sections/

appropriate Z sections and other sections of approved make

conforming to IS: 733 and IS: 1285, fixing with dash fasteners of

required dia and size, including necessary filling up the gaps at

junctions, i.e. at top, bottom and sides with required EPDM rubber/

21.1 neoprene gasket etc. Aluminium sections shall be smooth, rust free,

straight, mitred and jointed mechanically wherever required including

cleat angle, Aluminium snap beading for glazing / paneling, C.P.

brass / stainless steel screws, all complete as per architectural

drawings and the directions of Engineer-in-charge. (Glazing, paneling

and dash fasteners to be paid for separately) :

21.1.1 For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50

For shutters of doors, windows & ventilators including providing and

fixing hinges/ pivots and making provision for fixing of fittings

wherever required including the cost of EPDM rubber / neoprene

gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50

Providing and fixing glazing in aluminium door, window, ventilator

shutters and partitions etc. with EPDM rubber / neoprene gasket

21.3 etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid

in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50

Filling the gap in between aluminium frame and adjacent

RCC/Brickwork/ Stone Work by providing weather silicon sealant

over backer rod of approved quality as per architectural drawings

and direction of Engineer-in-charge

21.8.1 Upto 5mm depth and 5mm width Metre 4107.50 96.75 397400.63

22.0 WATER PROOFING

Providing and laying water proofing treatment to vertical and

22.3 horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of :

(i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with

water proofing compound conforming to IS 2645 in recommended

proportions including rounding off junction of vertical and horizontal

surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3

coarse sand) mixed with water proofing compound in recommended

proportion including rounding off junction of vertical and horizontal Sqm 1666.34 769.60 1282417.57

surface. (iii) IIIrd course of applying blown or residual bitumen applied

hot at 1.7 Kg. per sqm of area. (iv) IVth course of 400 micron thick

PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide

and pasted to each other with bitumen @ 1.7 Kg/sqm.)

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and laying integral cement based water proofing treatment

including preparation of surface as required for treatment of roofs,

balconies, terraces etc consisting of following operations: (a)

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement

admixed with water proofing compound conforming to IS. 2645 and

approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300 mm height including cleaning the surface

before treatment. (b) Laying brick bats with mortar using broken

22.7 bricks/brick bats 25mm to 115 mm size with 50% of cement mortar

1:5 (1 cement : 5 coarse sand) admixed with water proofing

compound conforming to IS : 2645 and approved by Engineer-in-

charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement

:5 coarse sand ) admixed with water proofing compound conforming

to IS : 2645 and approved by Engineer-in-charge to required slope

and treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement

slurry using 2.75 kg/ sqm of cement admixed with water proofing

compound conforming to IS : 2645 and approved by Engineerin-

charge. (d) Finishing the surface with 20 mm thick jointless cement

mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water

proofing compound conforming to IS : 2645 and approved by

Engineerin-charge including laying glass fibre cloth of approved

quality in top layer of plaster and finally finishing the surface with

trowel with neat cement slurry and making pattern of 300x300 mm

square 3 mm deep. (e) The whole terrace so finished shall be

flooded with water for a minimum period of two weeks for curing and

for final test.“All above operations to be done in order and as directed

and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra

Sunken area filling - Providing and laying on sunken areas broken

light weight concrete block bats of approximately 600 kg. per Cum

density laid, consolidated, finished smooth, including finishing &

MRW-01 grouting the top layer with 20 mm thick water proof cement mortar (1: Cum 81.96 7500.00 614666.25

4 ratio, 1 cement: 4 Sand) with CICO and as per specifications and

TOTAL CIVIL WORK 149210579.43 3683976.25

SUPPLY, INSTALLATION, TESTNG & COMMISSIONING OF SUB-

STATION EQUIPMENT

The rates under this section shall also include:

Supporting rigid frame work.

2 mm thick MS housing complete with dust and vermin proof covers

and lockable doors as called for.

All fixing accessories such as foundation bolts, nuts and bolts etc as

Touching up all damaged paint with approved paint shade.

All protection relays shall be numerical type

Compliance of technical specifications.

SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF SUB-

STATION EQUIPMENT

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying and erection of H Beam 13 Mtr Long 152x152 or 150x150

mm 37.1 Kg/Mtr. weight M.S. Pole complete with aligning and

keeping it in truly vertical position, including digging pit of required

size in all type of soil/rocks filling with 1:3:6 cement concrete of 0.60

mtr. dia. around the pole up to ground level including muffing of 0.45

mtr. dia. from ground level to 0.45 mtr. high as per specifications with

20 cm. thick base foundation in 1:4:8 cement concrete as

required refilling the pit with boulder and soil as required,

including painting of pole with bitumen paint below GL and two coats

of red oxide and two coats of aluminium paint or synthetic enamel

paint above GL as directed complete as per specification. The depth

of burying of pole shall be 1/6th of the length of .-2

Supplying and fixing of angle / channel / flat iron / RS Joist fittings for

over head lines as cross arms / brackets / clamps etc. including nut

bolts, required holes, welding, cutting, fabricating with necessary

materials including two coats of red oxide and two coats of

aluminium or synthetic enamel paint etc. as required.

Supplying and erection of 16mm dia 1.8 m long with 7/3.15mm stay

wire set complete with stay rod, anchor plate of size 300x300x5mm,

thimble, stay clamp, turn buckle, bow tightener etc. with stay wire,

NSR-3 strain insulator, nut bolts as per specifications including excavation in Each 16.00 1394.00 22304.00

all type of soil/ rocks and foundation in cement concrete 1:3:6 of

required size and other necessary materials complete as required as

per specifications.

Supplying and fixing polymer 11KVKV HT Disc (strain) insulator of

NSR-4 approved make on existing pole or bracket with GI hardware and Each 12.00 232.00 2784.00

other necessary materials complete as required.

Supplying and erection of D.P. structurre over existing support with

painting in an approved manner consisting of following:-

(a) D.C. cross arm with clamp and nuts bolts (100x50mm channel) –

(b) 11KV D.O. fuse unit, lighting arrester and A.B. switch mounting

channels with nuts and bolts (75x10mm channel) as required – 01

(c) Transformer mounting cross arms with clamps nuts and bolts

(100x50mm. Channels) – 1 set.

(d) Transformer clamping set with nuts and bolts etc. complete. 1 set.

(e) Transformer belting set with nuts and bolts etc. complete. – 1 set.

(f) Distribution pannel mounting channel and clamp with nuts and

bolts etc. (75x40mm channel).-1 set

(g) G.I. Pipe/bend as required for cable laying. -1 Job

(h) S/f DTR metering unit i/c meter box as per TLEB specification

complete. 01 Nos.

(i) G.I. pipe earthing complete with G.I. strip 25x3 mm as required

complete. 01 Job

(j) A.B. Switch as per T.N.E.R.C norms completed. 01 Set polymer

(k) L.A. as per T.N.E.R.C. norms completed. 03 Nos. - 01 Set

(L)D.O. fuse Unit set as per T.N.E.R.C. norms completed. 03 Nos. -

(M) D.P. structure complete as above. Complete as above (a to L)

Supplying and fixing polymer 11KV KV pin insulator with GI pin, of

NSR-6 approved make on existing pole or bracket with other necessary Each 12.00 261.00 3132.00

materials complete as required.

Supplying and drawing AAAC Rabbit conductor 0.05 sq inch (55

sq.mm al.eq) conductor of approved make with stringing making off

NSR-7 complete with binding at existing insulator, jointing, jumpering, km. 0.80 44136.00 35308.80

teeing off connecting etc. as required and clearing of obstacles (if

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying, laying, Terminating,testing and commissioning of XLPE

insulated and PVC sheathed heavy duty power cable confirming to

IS 7098/Part-I/88 with latest amendments, 1100 volts grade

armoured cable of approved make with aluminium solid / stranded

conductor. The cable shall be laid in air/in existing pipe/in existing

cable trench/on existing cable tray with clamp as required as per

specifications including providing of metal/PVC cable identification

tags at both ends and every 10 Mtr. length of cable with inscriptions

a)Un armoured cable 1 core 300 Sq.mm KM 0.12 255525.00 30663.00

b)Un armoured cable 1 core 150 Sq.mm KM 0.06 110000.00 6600.00

Supplying laying,terminating, testing and commissioning of XLPE

insulated and PVC sheathed heavy duty Arial bunch power cable

confirming to IS-7098/Part-I/88 with latest amendment, 1.1 KV grade

unarmoured cable of approved make with aluminium solid/stranded

conductor. The cable shall be laid in air as per specifications:

Supplying and fixing 2 ply 12 gauge barbed wire around the existing

HT/LT electric pole for safety measures as per IE rules including all

NSRE-01 stapples and all other necessary materials complete as Each 8.00 300.00 2400.00

required as per specifications.

Providing and fixing enamelled danger caution plate/board on

existing electric poles or wherever required of size 250x200 mm,

made of 1.6mm thick mild steel sheet and vitreous enamelled white,

with latest, figures and the conventional skull and cross-bones in

NSR-10 signal red colour (as per IS-5-1978 with latest amendment) on the

front side. The rear side of the plate shall also be enamelled. The

corner of the plate shall be rounded off with required material such

as screws, wires clamps, nut bolts etc. complete.

Supplying installing, connecting, testing and commissioning of

140KVA 11/.433 KV (COPPER wound without tap changing

arrangement) NLL 0.5 KW & FLL 3.0 KW 3 star rated, 3 Phase, 50

Hz, 11/0.433 KV, Delta/Star connected, Copper wound, oil filled,

Indoor/outdoor type, Distribution/Station transformer of accepted

standard specification, 3 star catagory class, with accessories such

as drain & filter valve, earthing terminals, lifting arrangements of

suitable size, dehydrating breather with silica gel of suitable size,

NSR-11 Conservator tank, air release devise, Rating & diagram plate Each 2.00 444094 888188.00

including CI rollers, Radiators with shut off valve, Cable end boxes on

HT & LT side bushings, Explosion vent with diaphragm, Off load tap

changing switch, Buchholz relay, thermometer pocket with 6” dial

type thermometer & OTI, wherever required complete with first

filling of oil with installation on existing DP structure or

foundation etc. complete as per specification.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and fixing of wiremesh fencing surrounding the existing DP

structure oldistribution transformer and panel system of different

sizes by adequate size of angle, flat iron and MS wire mesh jali

including nut, bolts, required holes, welding etc.and other necessary

materials as required. Frame is fabricated by MS angle of size

35x35x5mm runs horizontally on top and bottom of the frame. MS

wire mesh jali of size lxi” square of 13 guage MS bar, is

attached/fixed with the frame including strengthening to

1ali/wiremesh by flat iron of size 20x3mm on all sides of the frames.

The gate fabricated in the shape of frame is mentioned above, size

of angle 35x35x5mm is used on all sides. The opening is provided in

middle of two frames with the locking arrangement.The fabricated

wire mesh frame is painted with red oxide paint and alluminium paint

on portion above ground level a;d black paint on portion errected in

ground before errection Providing 13:6 cement concrete of 0 30

metre dra from ground level to 0.5 metre depth with 10cm base

foundatin. The rate includes for excavation in all type of soil/rock with

lead, lift and dressing etc. with curing and finishing of cement

concreting etc. complete. The Measurement and payment shall be

done as per measurements of wire mesh jali in Sqm. The other

materials/works shall be deemed to be included in quoted rates and

no extra payment will be made for any item/work involved in the

Supply of fire buckets 5 nos. in each set duly filled with fine sand and

fixed on an angle iron frame as per requirement of local authorities.

Fire buckets shall be painted red from outside and white from inside

with additional handle at the bottom.

Supply of tool kit with 1 pair 11KV rubber hand gloves of approved

TOTAL CARRIED TO SUMMARY 0.00 1867785.80

EARTHING INSTALLATION

Rates shall also include the following :

All fixing accessories such as brass saddles, brass screws rawl plugs

Jointing by rivetting and brazing after rivetting in case of copper and

welding / bolting in case of GI earthing.

Cutting chases holes and making good the same wherever required.

Effecting adequate and proper interconnections.

Use of copper thimbles.

Earthing system shall comply to IS:3043-1987.

All earthing pits shall be interconnected.

All equipment motors, DB’s, panels to be connected on either ends

(double earthing) with suitable strip / wires.

Supplying & laying, connecting testing and commissioning of

NSR 15 to following 1100 volt grade PVC sheathed XLPE insulated aluminium

18 conductor armoured cables as per specification in existing under

ground pipe as complete as required .

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying & laying of following 1100 volt grade XLPE insulated PVC

sheathed copper conductor armoured cables as per specification in

existing trenches, cable trays, ducts clamped includes anchor

fastners wall with suitable clamps, saddles fixing bolts including

connecting testing and commissioning.

NSR-19 4 core 6 sq.mm Copper RM 200.00 273.00 54600.00

NSR-20 2 core 6 sq.mm copper RM 400.00 266.00 106400.00

Cable end termination of the following PVC sheathed XLPE

insulated aluminium conductor armoured cables of 1100 volt grade

including supplying and fixing of crimping long barrel lugs, Single

compression glands with earthing facility at both ends of cables etc.

complete as required.

NSR-25 4 core 6 sq.mm Copper No. 16.00 307.00 4912.00

NSR-26 2 core 6 sq.mm copper No. 24.00 307.00 7368.00

TOTAL CARRIED TO SUMMARY 0.00 2662808.00

Supply and fixing of perforated type factory fabricated GI cable trays

of the following sizes including providing GI suspenders and supports

as per specifications..

TOTAL CARRIED TO SUMMARY 0.00 139440.00

LT CUM DG CHANGE OVER PANEL, MAIN DISTRIBUTION

The rates for the distribution boards apart from the Breakers and

instruments shall also include the following:

Supporting rigid steel framework.

Cubicle type, 14 gauge CRCA sheet steel enclosed & Type 3b

modular construction.

Complete with interconnections and distribution bus bars along with

connector strip.

Proper bonding to earth as per standard.

Painting/lettering on Breakers and distribution boards, the location

they serve, providing on each panel its circuit diagram.

Providing cable clamps / supports within distribution boards cable

TPN MCCB’s shall mean 3 pole MCCB’s with adequate size of

All MCB’s shall be of minimum 10 KA breaking capacity.

The breaking capacity of MCCB’s are mentioned panel wise. All

MCCB’s shall be with thermal magnetic releases as per BOQ and

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

i. MCCB rating upto 250 Amps with thermal magnetic releases.

Distribution panels / bus ducts / rising mains shall be Powder Coated

with Siemens gray paint shade no. RAL-7032 .

Degree of protection for following type of distribution panel enclosure

shall be as per IS:13947-1993.

i. IP 52 for indoor panels.

ii. IP 55 for outdoor panels.

All MCCB’s shall be provided with operating mechanism for door

GI earth bus shall be provided through out the length of each board

as per schematic diagram.

All measuring instruments (Meters) shall be of digital electronic (LED

Type) of approved make .

All hinged door shall be earthed through 2.5 sq mm tinned braided

All panels shall have provision of the following:

All MCB’s used for protection of resistive and lightly inductive load

shall be type “B” characteristic and inductive (motor) load shall be of

type “C” characteristic and discharge lamps and UPS etc. shall be of

type D characteristic.

CT’s shall be properally mounted and clamped. Connection of CT’s

for measuring instrument / relays shall be done through connector /

Model, current capacity location and frame size of switchgear shall

be written inside of the panel doors with paint / permanent marker as

approved shop drawings / site requirement.

Compliance to the technical specifications.

LT CUM DG CHANGE OVER PANEL, MAIN DISTRIBUTION

Supply,Installation, testing and commissioning of LT CUM DG

CHANGE OVER PANEL, MAIN DISTRIBUTION BOARDS,

fabricated out of 14 gauge CRCA sheet steel in cubicle

compartmentised modular 3b construction, free standing floor

mounted, dust and vermin proof with reinforcement of suitable size

angle iron, channel, `T’ sections and / or flats wherever necessary.

16 gauge CRCA sheet steel shall be used for final distribution panels.

3 mm thick cable gland plates shall be provided on top as well as at

NSR-29 the bottom of the panels. Panels shall be treated with all anticorrosive

process before powder coating as per specifications and final

approved shade. 2 Nos. earthing terminals shall be provided for all

distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4

wire, 50 HZ supply system. Lifting hooks shall also be provided in

case of large panels. Approval shall be taken for each panel in the

form of shop drawings before fabrication.Galvanised hardwares with

zinc passivation shall be used in fabrication of panels.

Incoming -Mains Supply

400 Amps 4 Pole, Microprocessor based MCCB with Over voltage ,

UnderVoltage, Over load and Earth Fault protection with 400 Amps 4

Pole contactor with Auto-Manual operation with following

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

VAF digital electronic meter with inbuilt selector switch and 400/5

Amps 15 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be provided with 2 Amps SP MCB's. - 3

ON/OFF indicating light shall be provided with 2 Amps SP MCB's. - 2

Under voltage relay MV12 or equivalnt (27) - 1 Set

Over voltage relay MV 12 or equivalent (59) - 1 Set

Auto-manual selector switch - 1 Set

Phase reversal relay - 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

required CTs for APFCR- 1 Set.

Incoming -DG Supply

400 Amps 4 Pole, Microprocessor based MCCB with Over voltage ,

UnderVoltage, Over load and Earth Fault protection with 400 Amps 4

Pole contactor with Auto-Manual operation with following

VAF digital electronic meter with inbuilt selector switch and 400/5

Amps 15 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be provided with 2 Amps SP MCB's. - 3

ON/OFF indicating light shall be provided with 2 Amps SP MCB's. - 2

Engine cranking relay - 1 Set

Microprocessor based engine control automatic failure stand by relay

including all accessories

Three indicating lamps “load on set’, ‘Load on Mains’ and “ Set fail to

Suitable rating battery charger shall be provided as per specifications

DC ammeter / Voltmeter for battery charger

24 V DC Shunt trip coil. - 1 Set

Auto-manual / test selector / switch - 1 Set

Auxiliary contacts required for necessary interlocking of breakers.

600 Amps TPN Aluminium bus bars with heat shrinkable insulation

sleeve. - 1 Set

250 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 1 No.

100 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 2 No.

63 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 3 No.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

250 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 1 No.

100 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 1 No.

63 Amps 4Pole MCCB with Multifunction Energy meter including

CTs complete as required - 1 No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA breaking capacity.

All the outgoing feeders shall be provided with ON/OFF Indication

NSR-29 LT CUM DG CHANGE OVER PANEL_described as above Set. 2.00 614900.00 1229800.00

250 Amps 4Pole MCCB with following accessories:

VAF digital electronic meter with inbuilt selector switch and 250/5

Amps 10 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be provided with 2 Amps SP MCB's. - 3

300 Amps TPN Aluminium bus bars with heat shrinkable insulation

sleeve. - 1 Set

40 Amps 4Pole MCB - 2 No.

63 Amps 4Pole MCB - 15 No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA breaking capacity.

All the outgoing feeders shall be provided with ON/OFF Indication

NSR-30 MDB-1_described as above Set. 2.00 348443.00 696886.00

NSR-31 MDB-2 (Emergency)

63 Amps 4Pole MCCB with following accessories:

VAF digital electronic meter with inbuilt selector switch and 60/5

Amps suitable VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. - 3

150 Amps TP+N Aluminiun bus bars with heat coloured shrinkable

insulation sleeve. - 1 Set

40 Amps DP MCB- 9No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA (Ics) breaking capacity in C curve.

NSR-31 Common Area Panel_ described as above Set 2.00 290000.00 580000.00

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply,Installation, testing and commissioning of LT CUM DG

CHANGE OVER PANEL, MAIN DISTRIBUTION BOARDS,

fabricated out of 14 gauge CRCA sheet steel in cubicle

compartmentised modular 3b construction, free standing floor

mounted, dust and vermin proof with reinforcement of suitable size

angle iron, channel, `T’ sections and / or flats wherever necessary.

16 gauge CRCA sheet steel shall be used for final distribution panels.

3 mm thick cable gland plates shall be provided on top as well as at

NSR-32 the bottom of the panels. Panels shall be treated with all anticorrosive

process before powder coating as per specifications and final

approved shade. 2 Nos. earthing terminals shall be provided for all

distrtibution panels. Panels shall be suitable for 415V, 3 phase, 4

wire, 50 HZ supply system. Lifting hooks shall also be provided in

case of large panels. Approval shall be taken for each panel in the

form of shop drawings before fabrication.Galvanised hardwares with

zinc passivation shall be used in fabrication of panels.

Providing and fixing of Main Distribution Panel ,outdoor type pole

mounting weather, dust and vermin proof made of 14 gauge MS

sheet with clamping arrangements, lockable hinged door duly painted

on all sides with red oxide after antirust and corrosion treatment, two

coats of synthetic enamel paints of approved make and shade,

consisting of following fittings:

250 Amps 4 Pole, Microprocessor based MCCB with Over voltage ,

UnderVoltage, Over load and Earth Fault protection with following

VAF digital electronic meter with inbuilt selector switch and 250/5

Amps 15 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be provided with 2 Amps SP MCB's. - 3

300 Amps TPN Aluminium bus bars with heat shrinkable insulation

sleeve. - 1 Set

125 Amps 4Pole MCCB with Tariff Energy meter including CTs

complete as required - 3 No.

125 Amps 4Pole MCCB with Tariff Energy meter including CTs

complete as required - 1 No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA breaking capacity.

All the outgoing feeders shall be provided with ON/OFF Indication

NSR32 MDB_described as above Set. 2.00 341611 683222.00

NSR-33 METER PANEL-1&2

125 Amps TP+N MCCB with following accessories:

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

VAF digital electronic meter with inbuilt selector switch and 125/5

Amps 10 VA, CL 1 CTs . - 1 Set

Phase indicating light shall be provided with 2 Amps SP MCB's. - 3

150 Amps TPN Aluminium bus bars with heat shrinkable insulation

sleeve. - 1 Set

40 Amps DP MCB with space for 40A ISI mark Single phase Tariff

energy meter-24 No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA breaking capacity.

All the outgoing feeders shall be provided with ON/OFF Indication

NSR-33 Meter Panel-1&2_described as above Set. 4.00 348443 1393772.00

NSR-34 COMMON AREA PANEL

125 Amps TP+N MCCB with following accessories:

VAF digital electronic meter with inbuilt selector switch and 125/5

Amps suitable VA, CL 1 CTs . - 1 Set

Phase indicating light shall be protected by 2 Amps SP MCB's. - 3

150 Amps TP+N Aluminiun bus bars with heat coloured shrinkable

insulation sleeve. - 1 Set

32 Amps DP MCB- 2No.

63Amps 4Pole MCCB- 5No.

40 Amps 4Pole MCB with export and Import meter- 1No.

All MCCB's shall be of 25 KA (Ics) breaking capacity.

All MCB's shall be of 10 KA (Ics) breaking capacity in C curve.

NSR-34 Common Area Panel_ described as above Set 2.00 290000 580000.00

FINAL DISTRIBUTION BOARDS :

Supply, installation, testing and commissioning of the following FDB's

fabricated out of 1.2 mm thick CRCA sheet steel, dust and vermin

proof, double door construction, powder coated with approved shade

NSR-35 . Approved lockable covers arrangement, recessed in wall or

surface mounted final distribution boards of the following description:

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

10 way SPN DB with 8No. 10 SP MCB’s with 1No. 40A DP RCCB of

100mA as incomer.(All MCB shall be 'C' curve)

Supply, installation, testing and commissioning of 63 Amps 4 pole

MCCB’s in MS Painted enclosure of approved make design and

painted with approved paint shade.

TOTAL CARRIED TO SUMMARY 0.00 6169352.00

EARTHING AND LIGHTINING PROTECTION INSTALLATION

Rates shall also include the following :

All fixing accessories such as brass saddles, brass screws rawl plugs

Jointing by rivetting and brazing after rivetting in case of copper and

welding / bolting in case of GI earthing.

Cutting chases holes and making good the same wherever required.

Effecting adequate and proper interconnections.

Use of copper thimbles.

Earthing system shall comply to IS:3043-1987.

All earthing pits shall be interconnected.

All equipment motors, DB’s, panels to be connected on either ends

(double earthing) with suitable strip / wires.

EARTHING AND LIGHTINING PROTECTION INSTALLATION

Providing and fixing 25 mm X 5 mm G.1. strip on surface or in recess

for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for

loop earthing as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm

thick including accessories, and providing masonry enclosure with

5.4 cover plate having locking arrangement and watering pipe of 2.7 set 32.00 5696.98 182303.36

metre lonq etc. with charcoal/ coke and salt as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia

300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6

6.2 mm thick G.I. base plate including holes etc. complete as required. each 24.00 518.00 12432.00

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or

surface of wall for lightning conductor complete as required.(For

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode

directly in ground as required.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia

including accessories, and providing masonry enclosure with

cover plate having locking arrangement and watering pipe etc.

with charcoal/ coke and salt as required.

TOTAL CARRIED TO SUMMARY 1192415.36 0.00

A WIRING IN STEEL AND PVC CONDUIT

Wiring for light point/ fan point/ exhaust fan point/ call bell point with

1.5 sq.mm FRLS PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with

1.10 modular switch, modular plate, suitable GI box and earthing the

point with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust

fan point/ call bell point ( without independent switch etc.) with 1.5

sq. mm FRLS PVC insulated copper conductor single core cable

1.55 in surface/recessed PVC conduit, and earthing the point with 1.5

sq. mm FRLS PVC insulated copper conductor single core cable

etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium

1.12 class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated meter 280.00 334.00 93520.00

copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring along with earth wire with the

1.14 following sizes PVC insulated copper conductor, single core cable in

surface / recessed Steel conduit as required.

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter 300.00 439.00 131700.00

Supplying and fixing of following sizes of Medium class PVC condute

along with accessories in surface/recess including cutting the walland

making good the same in case of recessed conduit as required.

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing 3

pin 5/6 A modular socket outlet and 5/6 A modular switch,

connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providng and fixing 2

1.56 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular Each 968.00 676.00 654368.00

switch, connections etc. as required. (For light plugs to be used in

non residential buildings).

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providng and fixing

1.57 25 A modular socket outlet and 2 SPMCB,including connections& Each 8.00 727.00 5816.00

Painting etc. as required. (For light plugs to be used in non residential

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying and fixing suitable size GI box with modular plate and

cover in front on surface or in recess, including providing and fixing 6

pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular

switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction

box/ wooden block including connections etc. as required.

Supplying and fixing two module stepped type electronic fan

1.25 regulator on the existing modular plate switch box including Each 3024.00 369.00 1115856.00

connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required.

Providing and fixing circular/hexagonal Fan box cast iron /metal

sheet Box for ceiling fan clamp of internal dia 140mm , 73 mm

Civil DSR height,Top id of 1.5mm thick MS sheet with its Top surface hacked of

2023 proper bonding top lid shall be screwed into cast iron /metal sheet Each 3024.00 220.65 667245.60

10.18 Box by mean of 3.3mm dia round headed screw one lock at the

corners.clamp shall be made of 12mm dia ms Bar band toshape as

per standrd drawing.

TOTAL CARRIED TO SUMMERY 9360425.60 0.00

LIGHTING FIXTURE AND FANS

Recessed mounted 12W LED down lighter with die cast aluminium

NSRL-35 housing with inbuilt controller and robust consction complete as No. 394.00 2777.00 1094138.00

required. (Toilet)

Recessed mounted 10W wall Surface Mounted lighter with die cast

NSRL-36 aluminium housing with inbuilt controller and robust consction No. 962.00 461.00 443482.00

complete as required.

Wall mounted 10W Bulk Head light fixture with die cast aluminium

NSRL-37 A housing with inbuilt controller and robust consction complete as Nos 82.00 1691.00 138662.00

Recessed mounted 10W Mirror lighter with die cast aluminium

NSRL-37 B housing with inbuilt controller and robust consction complete as No. 196.00 717.00 140532.00

Recessed mounted 12W Ceiling Down lighter with die cast

NSRL-38 aluminium housing with inbuilt controller and robust consction No. 388.00 3228.00 1252464.00

complete as required.

Recessed mounted 15W Ceiling Down lighter with die cast

NSRL-39 aluminium housing with inbuilt controller and robust consction No. 1170.00 2941.00 3440970.00

complete as required.

Recessed mounted 20W Wall Tube lighter with die cast aluminium

NSRL-40 housing with inbuilt controller and robust consction complete as No. 824.00 589.00 485336.00

Recessed mounted 20W Ceiling Tube lighter with die cast aluminium

NSRL-41 housing with inbuilt controller and robust consction complete as No. 160.00 543.00 86880.00

Supply and fixing of Ceiling fan of 1200mm sweep (white colour),

suitable for operation on 230 / 240V, 50 Hz, single phase, A.C,

NSRL-42 supply complete with double ball bearing motor, required down rod, Nos 3024.00 3638.00 11001312.00

capacitor, three MS blades etc complete.1200 MM Celing fan(Havells

Fusion Five Star 3 Blade (1200 mm)

300MM Exhaust fan in approved colour by engineering Incharge with

NSRL-44 Supply installation and testing of Call Bell app complete Nos 20.00 383.00 7660.00

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Self contained single sided exit sign for wall / ceiling / pendant

cantilever mounting with LED tube for non maintained battery backup

emergency lighting for 3 hours duration, approved equal in quality

Aviation obstruction light with Light Emitting Diods (LEDs). Complete

with all accessories as approved.

TOTAL CARRIED TO SUMMERY 0.00 18837910.00

EXTERNAL LIGHTING SYSTEM

Rate for supply and installation of fixtures shall also include the

All component that may be required to make the installation complete

in all respects, such as :

Suitable length of connecting wires.

Internal wiring between accessories.

Connecting wires to the point through connection block.

Bonding to earth wires.

Drilling holes in supports wherever required.

Fixing clamps, GI bolts and nuts/brass screws, saddles, rawl bolts

and other fixing accessories as required.

Painting with enamel paint of clAmps and other fixing accessories.

Testing of all fixture after installation.

Supply, Installation, testing and commissioning of the following

lighting fixtures or approved equivalent:

35 WLED based Street lighting Fixture, housing made up of Pressure

Die Cast Housing LM 6 Alloy/ Anti Dust Exposed Lens,sturdiness

and embossed brand name/logo name of manufacturer. The fixture

should have a minimum system efficacy of 110 lumen/Watt . The

fixture shall have a CRI of minimum 70. The fixture shall be designed

for a system life of 50,000 hours @70% lumen maintenance. Ingress

Protection of IP66 (lamp and gear Compartment) and Mechanical

Impact Resistance Rating of IK >=08.The fixture driver should have

an operating voltage range of 140-270 V, surge protection of >=3KV,

PF >0.9 , THD<10% and SDCM<5. The fixture should be top

openable & easy access to the Gear Compartment. The driver

should be BIS approved, fully potted and encapsulated with 440V

Stress Voltage protection for 8 Hrs. High Cut off : 325V(+/- 15V) and

Auto Restart function should also be available within the fixture.The

NSRL-47 fixture should comply with the parameters as per IS10322. The LED No. 48.00 9223.00 442704.00

driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics,

IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007

for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and

IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer shall have

inhouse lab approved by NABL or ministry of science of govt of India.

LM 79 and LM80 reports need to be submitted from a NABL/UL

accredited lab to verify above parameters.

Note : Light shall be mount direct on boundry wall with 3feet high

existing pole and 600 mm long 40mmdia existing single arm.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply, Installation, Testing and Commissioning of 27W LED Post

Top with a system lumen output of 2300 lumens and a minimum

system efficacy of >85 lm/W. The luminaire shall have a rated

system lifetime of 25,000 burning hours at L70. The luminaire should

NSRL-48 have a color temperature of 3000K and CRI > 70. The luminaire shall No. 8.00 2050.00 16400.00

meet IP65 with THD < 20% and PF > 0.9. The luminaire shall have

closed diffused optics with polycarbonate diffuser board. The total

power consumption should not exceed 27W (including driver).

Supply, Installation, Testing and Commissioning of 60mm dia and 2

feet long heavy class GI pipe pole along with welded 12mm thick

base plate hole for 4No. 200mm long Mounted nut,Bolt stud with

double washer (The cost of nut,Bolt stud with double washer shall be

included and the pole shall have two coat of Aluminimum/GI paint) .

Supply, Installation, Testing and Commissioning of pole single arm

made of 40mm dia and 2 feet long heavy class GI pipe including

mounting clamp and nut bolt with double washer complete as

Supply, laying, testing and commissioning of following size PVC

insulated aluminium conductor 1100 V grade armored cable

NSRL-51 including excavation sand filling providing brick protection, back filling

of earth, watering, ramming and consolidating of earth, complete:

Making end termination of following size PVC insulated aluminium

NSRL-52 conductor 1100 V grade armored cable including cost of crimping

lugs, insulation tapes, double compression glands etc. complete.

Wiring with 2 x 2.5 sq. mm. PVC insulated copper conductor 1100 V

grade wires in 16 gauge 25 mm dia heavy guage PVC conduit

NSRL-53 including connecting at the lighting fixtures complete. The cost shall RM 1152.00 136.00 156672.00

include supply and installation of conduit pipe, chasing of wall and

Supply, installation, testing and commissionin of

250MMX250MMx150MM polycarbonate weather proof (IP-55)

junction boxes including terminal / connector block complete as

Supplying and laying of following size DWC HDPE pipe ISI marked

along with all accessories like socket, bend, couplers etc. conforming

NSRL-55 to IS 14930, Part II complete with fitting and cutting,jointing etc.

Recessed in floor/Wall, complete as required.

63 mm dia (OD-63 mm & ID-51 mm nominal) RM 800.00 128.00 102400.00

TOTAL CARRIED TO SUMMARY 0.00 1485808.00

FIRE ALARM SYSTEM

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm

panel, central processing unit with the following loop modules and

capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length

up to 2 km, network communication card, minimum 320 character

graphics/ LCD display with touch screen or other keypad and

minimum 4000 events history log in the non volatile memory

(EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up

17.2.1 with 24 volt sealed maintenance free batteries with automatic

charger. The panel shall have facility to connect printer to

printout log and facility to have seamless integration with

analog/digital oice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be

complete with all accessories . The panel shall be compatible for

IBMS system with open protocol BACnet/ Modbus over IP

complete as per specifications.

Supplying, installation, testing & commissioning of addressable

17.2.10 fire control module complete as required. each 8.00 3003.00 24024.00

Supplying, installation, testing & commissioning of addressable

17.2.11 phone control module complete as required. each 4.00 3267.00 13068.00

Supplying, installation, testing & commissioning of addressable

17.2.14 manual call point complete as required. each 28.00 3871.00 108388.00

Supplying, installation, testing & commissioning of addressable

17.2.15 horn cum strobe complete as required. each 54.00 3506.00 189324.00

Supplying, installation, testing & commissioning of addressable

17.2.16 strobe complete as required. each 54.00 3367.00 181818.00

Supplying, installation, testing & commissioning of fire

17.2.17 fighter telephone handset complete as required. each 28.00 5740.00 160720.00

Supplying, installation, testing & commissioning of fire fighter

17.2.19 phone jack complete as required. each 54.00 1600.00 86400.00

Supply , Installation , Testing and Commissioning of Monitor Module.

Supplying and drawing following sizes of FRLS PVC insulated copper

1.17 conductor, single core cable in the existing surface/ recessed steel/

PVC conduit as required.

Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit as required.

TOTAL CARRIED TO SUMMERY 1867822.00 13800.00

PUBLIC ADDRESS SYSTEM

Supplying and drawing following sizes of FRLS PVC insulated copper

1.17 conductor, single core cable in the existing surface/ recessed steel/

PVC conduit as required.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall

and making good the same in case of recessed conduit as required.

Supplying, installation, testing & commissioning of 1.5/3/6W

17.3.2 ceiling speaker complete as required. each 236.00 965.00 227740.00

Supply, installation, testing and commissioning of rack mounted dual

Channel Digital Power Amplifier capable of delivering 300 W RMS

power output or 480 W RMS burst output; complete with 100 V Line

Matching Transformer, built-in fan for temperature control, Distortion

NSR-57 typically 0.03% @ 1 KHz, Hum and Noise 90 dB below rated output No. 4.00 45255.26 181021.06

selection facility,provision for hookup with Fire Alarm Panel, complete

with connections and required circuitry. Same shall be intergrate with

Fire alarm system.

Supply, installation, testing and commissioning of 19" equipment rack

made out of 2 mm thick CRCA sheet duly powder coated; in-built

amplifier mounting; amplifier, controller, suitable for housing of above

control equipment.

Supply, installation, testing and commissioning of micro phone for

NSR-59 remote location and interface with controller including communication Nos. 4.00 9873.00 39492.00

cable and all accessories.

TOTAL CARRIED TO SUMMERY 528740.00 357569.06

CCTV (IP VIDEO SURVEILLANCE) SYSTEM

Supply, installation, testing and commissioning of Out door type

Fixed camera with discreet and tamper-resistant casing. Varifocal

2.8-10 mm lens with fixed iris. Multiple, individually configurable

NSR-60 H.264 and Motion JPEG streams; max HDTV 720p or 1 MP Nos. 12.00 33102 397224.00

resolution at 30 fps. Video motion detection and active tampering

alarm. Power over Ethernet. Midspan not included.The camera shall

have sound in facility.

Supply, installation, testing and commissioning of Fixed dome with

discreet and tamper-resistant casing. Varifocal 2.8-10 mm lens with

fixed iris. Multiple, individually configurable H.264 and Motion JPEG

NSR-61 streams; max HDTV 720p or 1 MP resolution at 30 fps. Video motion Nos. 132.00 14518 1916376.00

detection and active tampering alarm. Power over Ethernet. Midspan

not included.The camera shall have sound in facility.

Supply, installation, testing and commissioning of 24 channel NVR

with two video outputs . Contractor shall size the NVR for real time

400 FPS / 4 CIF resolution 30 days of continous recording and

NSR-62 submit data sheet of their storage calculation for both MPEG 4 and Nos. 4.00 110340 441360.00

H.264 recording formats. The NVR with IP connectivity, DVD R/W &

USB connectivity with all necessary softwarealong with standalone

UPS with 15 min. Battery back.

Supply, installation, testing and commissioning of 55" totally flat

NSR-63 colour LCD monitor with mouted accesseries complete as required. Nos. 4.00 63881 255524.00

Supply, installation, testing and commissioning of Joy Sticks with

mouted accesseries complete as required.

Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH

Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS

Compliant, patch cord 1 Mtr for rack side switch to jack panel

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply, Installation, Testing & Commissioning of loaded 24 port CAT

6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black

with cable support bar, clear label marks and earthing plug for

CAT6A cable termination at rack end.

Supply, Installation, Testing and Commissioning of 24 port L2

Managed switch having port density 24 Nos. of 10M/100M/1G RJ45

Port POE/POE+ ports , 4 Nos. of 1G/10G SFP+ Port , 1X console

port , Available POE power 370 W , 128 Gbps switching bandwidth ,

32K MAC address support , Support L2 feature STP, RSTP ,MSTP .

NSR-67 Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC Nos. 4.00 24000 96000.00

based VLAN , IP subnet based VLAN . Support IEEE 802.3ad LACP

. L3 features - static routing , DHCP server , Device Management

system - topology view , floor view , map view , dashboard , traffic

monitoring , cable diagnostics.CE,FCC certified

Supply, Installation, Testing & Commissioning of I LIU ,PDU for

Supply, Installation, Testing & Commissioning of armoured 6 core

fiber Singlemode OS2 (9/125 Micro), Corrugated ECCS Armor,

HDPE (UV) Sheathing, Theoxtropic gel filled OFC cable with 2 Nos

steel music wire embedded in side sheathing as stregth member for

switch connectivity. Cable should be ROHS compliant and as per

IEC60749-1 with product warranty of 30 years.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall

and making good the same in case of recessed conduit as required.

TOTAL CARRIED TO SUMMERY 409360.00 5417120.00

DATA , VOICE SYSTEMS

Supplying and fixing following piano type switch/ socket on the

existing switch box/ cover including connections etc. as required.

1.24.6 Telephone socket outlet Each 20.00 148.00 2960.00

Supplying and fixing following size/ modules, GI box alongwith

1.27 modular base & cover plate for modular switches in recess etc. as

Supplying and fixing following Modular base & cover plate on existing

modular metal boxes etc. as required.

Supply, Installation, Testing & Commissioning of 42 U (600W/1000D)

NSR-70 floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. 4.00 52.00 208.00

Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of 15U wall mount

NSR-71 rack with fans , 2 cable managers , satationary shelf , 2 Nos. of Nos. 4.00 4123.00 16492.00

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply, Installation, Testing & Commissioning of CAT 6A UTP

Universal (both tool & toolless) information outlet (I/O) in accordance

with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR

11801-9901-2014, ROHS Compliant. The I/O should have minimum

750 mating cycle and 200 insertion cycle and UL approved, for Data,

Voice, & Wi-Fi at user end.

Supply, Installation, Testing & Commissioning of loaded 24 port CAT

6A UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black

with cable support bar, clear label marks and earthing plug for

CAT6A cable termination at rack end.

Supplying and drawing following pair 0.5 mm dia FRLS PVC

1.18 insulated annealed copper conductor, unarmored telephone cable in

the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surface/ recessed Steel/ PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit

along with accessories in surface/recess including cutting the wall

and making good the same in case of recessed conduit as required.

TOTAL CARRIED TO SUMMERY 42180.00 52936.00

Supply, installation, Testing and commissioning of the following UPS

SYSTEM as per specifications and complete in all respects.

10 KVA 3 phase input (415 V + 15%), three phase output (415 V +

1%) in stand alone mode with isolation transformer with 15 minutes

battery backup each complete with battery rack & inter connector for

batteries & Isulation switch for each bank battery.

Quoted price shall be inclusive of the following:

Approved rating single core copper conductor cable connecting as

All equipment shall be housed in individual cabinets.

Battery backup must be given for full resistive load. Battery should

be sealed maintenance free type.

Battery monitoring system shall be provided.

TOTAL CARRIED TO SUMMARY 0.00 1400000.00

Design, manufactures, supply,installation, testing,commissioning,

approvals / laisoning (All local / state/ central statutory bodies) and

handing over in satisfactory working conditions of elevators as per

specification ans approved make.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

13Passenger (884Kg.) Elevator with 2200X2350 mm shaft,

machine room consisting of ACVVVF Panel, 4800mm over

head,1600mm Pit including withiring, 1.5MPS speed, 6 No. Stops ,

car size with 900x2100mm car entrance and door opening for

NSR-75 stracture with Automatic with Centre opening ACVVVF Motor Door No. 8.00 2613324.60 20906596.80

operator with electronic / infrared sensor door detector, all floor

opening in same side ,moon rock finish stainless steel complete in

all respect as per specification.

(i) Necessary wiring/control wiring, conduit/raceway if required for

satisfactory operation of elevators shall be in the scope of lift vendor.

(ii) Size of car should be fit in lift well.

TOTAL CARRIED TO SUMMERY 0.00 20906596.80

SMOKE EXTRACTION SYSTEM

AXIAL FLOW FANS

Supply, Installation, Testing and Commissioning of Long Casing

(motor should completely accommodated inside the casing) AXIAL

FANS for exhaust air suitable for installing in any position in

Horizontal or vertical. Fan shall be AMCA Certified. The motor shall

be of class F/H (H class wherever specified in the item, to withstand

a temperature of 250 degree celcius for 2 hours) suitable for 415 V ±

NSR-76 10% volts three phase 50cycle, AC supply & meeting criterion as per

ASHRAE standard 90.1-2010 and high efficiency (IS 12615). The fan

shall be equipped with mounting bracket Inlet & outlet cone required

at discharge. The fan shall be low RPM (less than 1450 RPM) and

capacities shall be as follows:-

Duty :- Smoke Extraction (Fresh Air)

Air Quantity : 8000 CFM

Static Pressure : 25 mm wg

NSR-76 Fan Motor H.P: 2.5 H.P Class-f Motor Nos. 8.00 131179.00 1049432.00

SMOKE EXTRACTION SYSTEM

AXIAL FLOW FANS

Supply, Installation, Testing and Commissioning of Long Casing

(motor should completely accommodated inside the casing) AXIAL

FANS for exhaust air suitable for installing in any position in

Horizontal or vertical. Fan shall be AMCA Certified. The motor shall

be of class F/H (H class wherever specified in the item, to withstand

a temperature of 250 degree celcius for 2 hours) suitable for 415 V ±

NSRS-01 10% volts three phase 50cycle, AC supply & meeting criterion as per

ASHRAE standard 90.1-2010 and high efficiency (IS 12615). The fan

shall be equipped with mounting bracket Inlet & outlet cone required

at discharge. The fan shall be low RPM (less than 1450 RPM) and

capacities shall be as follows:-

Duty :- Smoke Extraction (Fresh Air)

Air Quantity : 7000 CFM

Static Pressure : 25 mm wg

NSRS-01 Fan Motor H.P: 2.5 H.P Class-f Motor Nos. 4.00 85000 340000.00

AIR DISTRIBUTION

Supply, installation, balancing and commissioning of factory

fabricated GSS sheet metal rectangular/round ducting complete with

neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,

NSRA-02 supports etc. as per approved drawings and specifications of

following sheet thickness complete as required.

(It shall be as per SMACNA standards)

Thickness 26 G Galvanized Sheet Steel Ducting Sqm. 40.00 1719.00 68760.00

TOTAL CARRIED TO SUMMARY 0.00 1458192.00

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply, installation, testing and commissioning of 160 KVA prime

continuous (actual) rating radiator cooled type diesel generating set

(alternature at 40 deg C temperature) with Acoustic Enclosure along

with electronic governor base frame, Alternator (capable of delivering

true 40 kVA output), Static Excitation System, Lube Oil System,

NSD-01 Batteries, Battery charger, Instrumentation, 990 liter day oil fuel Nos. 2.00 1250000.00 2500000.00

tanks, Silencer with bellows, alarms, Engine Control Panel, AVM

pads, AVR Panel,Terminal arrangements in termination box suitable

to 3.5cx50 sqmm aluminium cables with all other associated

equipment / work as per specifications. The DG Set shall comply

Supply, installation, testing and commissioning of exhaust pipe 'B'

class heavy duty MS pipe with all fixing accessories and hardwares.

NSD-02 The exhaust pipes shall be insulated with 75 mm thick mineral wool

insulation wrapped in chicken mesh and clad with 24 gauge

aluminium sheet including all support.

TOTAL CARRIED TO SUMMARY 0.00 2590000.00

TOTAL ELECTRICAL 13400942.96 63359317.66

SANITARY FIXTURES & FITTINGS

14.80 Providing & fixing White vitreous china water closet squatting

pan (Indian type) along with “S” or “P” trap including dismantling of

old WC seat and “S” or “P” trap at site complete with all operations

including all necessary materials, labour and disposal of dismantled

material including malba, all complete as per the direction of

Engineer-in charge.

14.80.2 Orissa pattern W.C Pan of size 580x440 mm Each 22.00 4478.75 98532.50

Providing and fixing of white vitreous china pedestal type water closet

(European type W.C. pan) with seat and lid, 10 litre low level white

P.V.C. flushing cistern, including flush pipe, with manually controlled

device (handle lever), conforming to IS : 7231, with all fittings and

fixtures complete, including cutting and making good the walls and

floors wherever required

17.2.1 W.C. pan with ISI marked white solid plastic seat and lid Each 176.00 6515.55 1146736.80

17.34 Providing and fixing toilet paper holder

Providing and fixing of low flow type two way bib cock and flow

restrictor 6 LPM at 3 Bar Pressure as per approved make complete

in all respect as per engineer in the charge. (Only for EWC.)

Providing and fixing of Health faucet with 1 m of C.P. brass flexible

pipe and direction of Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP

Brass single hole basin mixer of approved quality and make,

17.7A including painting of fittings and brackets, cutting and making good

the walls wherever required:

a) White Vitreous China Wash basin size 550x400 mm with a 15

mm CP Brass single hole basin mixer

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain

with rubber plug, 40 mm C.P. brass waste complete, including

17.9 painting the fittings and brackets, cutting and making good the walls

wherever required:

17.9.1 White glazed fire clay kitchen sink of size 600x450x 250 mm Each 102.00 3892.75 397060.50

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing and fixing CP Brass 32 mm size Bottle Trap of approved

17.22A quality & make and as per the direction of Engineer-in-charge. Each 304.00 1034.80 314579.20

Providing and fixing CP Brass Single lever telephonic wall mixer of

17.22B quality & make as approved by Engineer in charge. 15 mm nominal Each 310.00 6940.75 2151632.50

Providing and fixing PTMT liquid soap container 109 mm wide, 125

mm high and 112 mm distance from wall of standard shape with

bracket of the same materials with snap fittings of approved quality

and colour, weighing not less than 105 gms.

Providing and fixing PTMT soap Dish Holder having length of

18.65 138mm, breadth 102 mm, height of 75 mm with concealed fitting Each 198.00 111.45 22067.10

arrangements, weighing not less than 106 gms

Providing and fixing of C.P. brass angle valve for basin mixer and

geyser points of approved quality conforming to IS:8931

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1

17.16A metre long with S.S. triangular plate to Eureopean type W.C. of Each 1109.00 349.15 387207.35

quality and make as approved by Engineer - in - charge

Providing and fixing of following capacity of vertical or horizontal

storage type hot water heater fixed to wall with anchor bolts & nuts,

15mm CP brass angle stop cock and 15mm CP brass non-return

valve complete including making connections with 15mm dia CP

connecting pipes on inlet and outlet, suitable length of power cable

and 15 amps plug direction of Engineer-in-charge.

Capacity: 25 Ltr. (Only for bath areas) Each 4.00 25000.00 100000.00

INTERNAL & EXTERNAL WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe with

18.7 clamps at 1.00 m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and testing of joints complete as

per direction of Engineer in Charge.(For Domestic & Flushing water

Internal work - Exposed on wall

18.7.1 15 mm nominal outer dia Pipes Metre 9.00 286.80 2581.20

18.7.2 20 mm nominal outer dia Pipes Metre 188.00 335.00 62980.00

18.7.3 25 mm nominal outer dia Pipes Metre 90.00 401.55 36139.50

18.7.4 32 mm nominal outer dia Pipes Metre 110.00 518.75 57062.50

18.7.5 40 mm nominal outer dia Pipes Metre 145.00 702.95 101927.75

18.7.6 50 mm nominal outer dia Pipes Metre 39.00 934.15 36431.85

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply including all CPVC

plain & brass threaded fittings This includes jointing of pipes & fittings

with one step CPVC solvent cement, trenching, refilling & testing of

joints complete as per direction of Engineer in Charge. External work

18.9.7 65 mm nominal outer dia Pipes Metre 11.00 1674.40 18418.40

Concealed work, including cutting chases and making good the

18.8.1 15 mm nominal outer dia Pipes Metre 874.00 497.80 435077.20

18.8.2 20 mm nominal outer dia Pipes Metre 418.00 537.60 224716.80

18.8.3 25 mm nominal outer dia Pipes Metre 690.00 627.25 432802.50

Providing and fixing G.I. pipes complete with G.I. fittings and

clamps,including cutting and making good the walls etc.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Internal work - Exposed on wall

18.10.1 15 mm nominal outer dia Pipes Metre 4.00 366.40 1465.60

18.10.2 20 mm nominal outer dia Pipes Metre 168.00 437.30 73466.40

18.10.3 25 mm nominal outer dia Pipes Metre 34.00 551.70 18757.80

18.10.4 32 mm nominal outer dia Pipes Metre 364.00 667.00 242788.00

18.10.5 40 mm nominal outer dia Pipes Metre 244.00 811.90 198103.60

18.10.6 50 mm nominal outer dia Pipes Metre 254.00 1048.35 266280.90

Providing and fixing of 'B' class heavy duty G.I. pipes confirming to

IS: 1239 Including welding fitting like elbow, tee flages, taper,

FF-DSR nuts,bolt gaskit etc, and fixing of pipe on the ceiling/wall with suitable

2019 clamp /support fram and painting two or more coat of enamle paints

of required shed complete as required.

Internal work - Exposed on wall

Providing, laying, testing & commissioning of 'B' class heavy duty G.I.

pipe conforming to IS 1239 including welding, fittings like elbows,

tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on

the wall/ceiling with suitable clamp/support frame and painting with

two or more coats of synthetic enamel paint of required shade

complete as required

Providing and fixing G.I. pipes complete with G.I. fittings including

trenching and refilling etc

18.12.3 25 mm dia nominal bore Metre 4.00 467.75 1871.00

18.12.4 32 mm dia nominal bore Metre 22.00 540.30 11886.60

18.12.5 40 mm dia nominal bore Metre 22.00 617.05 13575.10

Making connection of G.I. distribution branch with G.I. main of

18.13 following sizes by providing and fixing tee, including cutting and

threading the pipe etc. complete :

25 to 40 mm nominal bore

18.13.2 50 to 80 mm nominal bore Each 8.00 1785.35 14282.80

Fixing water meter and stop cock in G.I. pipe line including cutting

18.14 and threading the pipe and making long screws etc. complete (cost Each 4.00 812.30 3249.20

of water meter and stop cock to be paid separately).

Providing and fixing gun metal gate valve with C.I. wheel of approved

quality (screwed end) :

18.17.2 32 mm nominal bore. Each 4.00 689.60 2758.40

18.17.3 40 mm nominal bore Each 4.00 826.10 3304.40

Providing and fixing ball valve (brass) of approved quality, High or

low pressure, with plastic floats complete

18.18.2 20mm nominal bore Each 50.00 462.50 23125.00

18.18.3 25mm nominal bore Each 94.00 464.05 43620.70

Providing and fixing motorised butterfly valve rating PN 1.0 with float

type sensors suitable for 240 volts with working pressure rating of

not less than 5 kg/cm2 with control panel and sensors to open valve

when water level is low in tanks and to close when water level is

high in water tanks including butterfly valves, necessary cables,

conduits, upto junction box etc. complete. (upto 6 mt qty approx.)

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

NSRW-4 32 mm dia ( FLUSHING RISER) Each 4.00 19305.00 77220.00

NSRW-5 40 mm dia ( DOMESTIC RISER) Each 4.00 23077.00 92308.00

Providing and fixing M.S fabricated hot dipped galvanized coating

puddle flange comprising of 600 mm dia long M.S class 'B' pipe

(screwed end up to 50 mm & flange for more than 50 mm dia) with 6

mm thick M.S plates of required size including cutting holes in centre

NSRW-06 to of plate, inserting pipe & making welded (Arc) joint complete. Same

NSRW- 12 shall be installed with TEC welded joint in position with reinforcement

bars of RCC tank wall/slab including making cutout in shuttering

during concrete casting of tank of following diaMtr.. (Location:

overhead tanks.)(Jindal star)

Painting G.I. pipes and fittings with two coats of anti-corrosive

bitumastic paint of approved quality :

18.40.3 25 mm dia nominal bore Metre 4.00 18.35 73.40

18.40.4 32 mm dia nominal bore Metre 22.00 22.20 488.40

18.40.5 40 mm dia nominal bore Metre 22.00 25.24 555.28

SOIL, WASTE, VENT PIPES & FITTINGS FOR INTERNAL

Providing and fixing unplasticised PVC pipe clips of approved design

to unplasticised - PVC rain water pipes by means of 50x50x50 mm

hard wood plugs, screwed with M.S. screws of required length,

including cutting brick work and fixing in cement mortar 1:4 (1 cement

: 4 coarse sand) and making good the wall etc. complete.

Providing, fixing, jointing and testing in position the following uPVC

pipes conforming to IS: 4985 of 6 kg/sqcm pressure rating including

NSRW-13 to all fittings, solvent weld joints, testing complete for drainage system

NSRW-15 cut to required length to be laid under floor and exposed including

covering all around with cement concrete and making good the same

complete as required.

Providing & fixing 75mm x 50mm UPVC waste with reducing elbow &

nipple (floor drain ) including cutting chases, the floor / slab, repairs

complete as required and connection to upvc waste pipe.

Providing & Fixing, Testing & Commissioning of Heavy class S.S.

grating with Cockroach proof SS strainer of approved design

including setting in floor with cement mortor to match with floor finish

as per architect requirement suitable for waster and FT.

Providing and fixing uPVC clean out plug with uPVC socket complete

NSRW-18 with all necessary fitting complete as required by the engineer-in-

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

STROM WATER PIPES & FITTINGS

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing to the inlet mouth of rain water pipe cast iron

grating 15 cm diameter and weighing not less than 440 grams.

NSRW-19 Providing and fixing CPVC gratings for Rain Water Pipes.

Providing and laying non-pressure NP2 class (light duty) R.C.C.

pipes with collars jointed with stiff mixture of cement mortar in the

proportion of 1:2 (1 cement : 2 fine sand) including testing of joints

Designing and constructing brick masonry manhole chamber of the

following size in brick work of class 75 in cement mortar 1:4

(1cement:4 fine sand), SN-4. top slab with 1:2:4 mix (1cement : 2

coarse sand :4 graded stone aggregate 20mm. nominal size) RCC

foundation slab 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone

aggregate 40 mm nominal size) both inside and outside cement

plastering 12 mm thick with cement motar 1:3 (1cement :3 coarse

sand) finished with a floating coat of neat cement on inside face,

proper water proofing to ensure no ground water seepage in the

NSRW-20 manhole, M.S. polypropylene coated foot rests at 300 mm spacing,

benching and making channels in 1:2:4 cement concrete neatly

finished, including necessary centering and shuttering,

reinforcement, excavation, in all kind of soil, dewatering, refilling,

watering, ramming and removing the surplus excavated earth,

making good the same complete as required. Contractor shall submit

the structural design and drawings for the approval of Project

Manager prior to execution including SFRC Cover and frame (heavy

duty HD-20 grade designation)

NSRW-20 For Rectagular Manhole size 0.90X 0.80 m RM 22.00 5000.00 110000.00

Providing orange colour safety foot rest of minimum 6 mm thick

plastic encapsulated as per IS : 10910 on 12mm dia steel bar

conforming to IS : 1786 having minimum cross section as 23

mmx25mm and over all minimum length 263 mm and width as

165mm with minimum 112 mm space between protruded legs having

2 mm tread on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on tail length on 138

19.16 mm as per standard drawing and suitable to with stand the bend test Each

and chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible even after

fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 20 mm nominal size) complete as per design.

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms,

depth upto 1.5 m, including getting out the excavated soil, and then

2.10 returning the soil as required, in layers not exceeding 20 cm in depth,

including consolidating each deposited layer by ramming, watering,

etc. and disposing of surplus excavated soil as directed, within a lead

2.10.1 All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Making desiliting chamber in rectangular shape, finished size upto

3.0 m x 1.5 m x 2.0. Including the all civil work {earth work in all type

of soil, providing and laying in position P.C.C & R.C.C, required

centering and shuttering, reinforcement steel, erecting brick work in

NSRW-22 FPS bricks of class designation of cement mortar in 1 :6, laying 12 to

15 mm thick cement plaster of 1 : 2 : 4 (1 Cement : 2 Coarse sand :

4 fine Sand). as per drawing or as per direction of engineer - in-

Rates includes the cost of providing and laying, Fixing

a) 450 mm thick coarse sand

b) 400 mm thick layer of Boulder of 50 mm to 100 mm in size,

c) 400 mm thick layer of of boulder 50 to 200 mm in size.

NSRW-22 d) Heavy duty manhole cover of 5400 x 540 x 100 mm two number Each 4.00 150000.00 600000.00

e) fixing heavy duty pvc rungs @ 300 c/c

f) fixing 250 mm dia to 450 mm dia inlet & outlet points

g) making required cutout of required size. (refer enclosed drawing)

EXTERNAL SEWERAGE SYSTEM

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse

19.6 sand : 10 graded stone aggregate 40 mm nominal size) all-round

R.C.C. pipes including bed concrete as per standard design:

250 mm dia. R.C.C. pipe

Providing and fixing stoneware gully trap of the following sizes in

brick masonary chamber of standard design with first class bricks

and trap to be set in cement concrete 1:2:4, both side 12mm thick

plastering with floating coat of neat cement. Making necessary

connections & providing water tight D.I. cover with frame of 300mm x

NSRW-23 300mm internal size. The weight of cover & frame not be less than 8 No 34.00 2000.00 68000.00

kg as per standard design. Including necessary excavation,

dewatering, refilling, watering, ramming and removing the surplus

excavated material and making good the same complete as

Designing and constructing brick masonry manhole chamber of the

following size in brick work of class 75 in cement mortar 1:4

(1cement:4 fine sand), SN-4. top slab with 1:2:4 mix (1cement : 2

coarse sand :4 graded stone aggregate 20mm. nominal size) RCC

foundation slab 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone

aggregate 40 mm nominal size) both inside and outside cement

plastering 12 mm thick with cement motar 1:3 (1cement :3 coarse

sand) finished with a floating coat of neat cement on inside face,

proper water proofing to ensure no ground water seepage in the

NSRW-24 manhole, M.S. polypropylene coated foot rests at 300 mm spacing,

benching and making channels in 1:2:4 cement concrete neatly

finished, including necessary centering and shuttering,

reinforcement, excavation, in all kind of soil, dewatering, refilling,

watering, ramming and removing the surplus excavated earth,

making good the same complete as required. Contractor shall submit

the structural design and drawings for the approval of Project

Manager prior to execution including SFRC Cover and frame (heavy

duty HD-20 grade designation)

For Rectagular Manhole size 0.90X 0.80 m Each 28.00 5000.00 140000.00

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Providing orange colour safety foot rest of minimum 6 mm thick

plastic encapsulated as per IS : 10910 on 12mm dia steel bar

conforming to IS : 1786 having minimum cross section as 23

mmx25mm and over all minimum length 263 mm and width as

165mm with minimum 112 mm space between protruded legs having

2 mm tread on top surface by ribbing or chequering besides

necessary and adequate anchoring projections on tail length on 138

19.16 mm as per standard drawing and suitable to with stand the bend test Each 28.00 553.70 15503.60

and chemical resistance test as per specifications and having

manufacture's permanent identification mark to be visible even after

fixing, including fixing in manholes with 30x20x15 cm cement

concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone

aggregate 20 mm nominal size) complete as per design.

Excavating trenches of required width for pipes, cables, etc including

excavation for sockets, and dressing of sides, ramming of bottoms,

depth upto 1.5 m, including getting out the excavated soil, and then

2.10 returning the soil as required, in layers not exceeding 20 cm in depth,

including consolidating each deposited layer by ramming, watering,

etc. and disposing of surplus excavated soil as directed, within a lead

2.10.1 All kinds of soil

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm

Constructing brick masonry water tight grease trap (with three

chambers , each of 0.4 M X 0.6 M in plan) with 75 class designation

bricks in cement mortar 1 : 5 ( 1 cement : 5 fine sand ) earth work,

excavation in all kinds of soil, foundation concrete 1 : 4 : 8 mix (1

cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal

size) inside and outside plastering 12 mm thick with cement mortar 1

NSRW-25 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat

cement including constructing baffle wall, stainless steel angles on

corners, stainless steel perforated plates with stainless steel lifting

handles in each chamber, inlet and outlet fittings in UPVC, double

seal C.I. covers complete as per standard design:

Inside size 2.0m x 1.5m and 1.0m deep including two nos. 60x60 cm.

NSRW-25 C.I. Cover and frame (double seal weight of cover and frame not less Each 4.00 62372.59 249490.38

TOTAL PLUMBING 10921214.13 2844320.38

FIRE PUMP & PIPE & ACESSERIES

Supplying, installation, testing and commissioning of electric driven

terrace pump suitable for automatic operation and consisting of

following, complete in all respects, as required: (Terrace Pump)

(a) Horizontal type, multistage, centrifugal, split casing pump of cast

iron body & bronze impeller with stainless steel shaft, mechanical

confirming to IS : 1520

b) Suitable HP squirell cage induction motor TEFC type suitable for

operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of

protection for enclosure, horiziontal foot mounted type with Class-'F'

insulation, conforming to IS-325.

(c) M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc.as required.

(d) Suitable cement concrete foundation duly plastered and with anti

vibration pads.

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS

sheet, 1200 mm in height with air release valve on top and flanged

connection to riser, drain arrangement with 25 mm dia gun metal

wheel valve with required accessories, pressure gauge and

paintingwith synthetic enamel paint of approved shade as required.

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Note:Contractor shall include in his rates for providing level

controllers, pressure switches, wiring, cabling from level controller /

pressure switch to panel etc. complete as required to operate the

system automatic/manual. Pump shall be protected against running

Providing, laying, testing & commissioning of 'C' class heavy duty

MS pipe conforming to IS 3589/IS 1239 including Welding, fittings

like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing

7 the pipe on the wall/ceiling with suitable clamp/support frame and

painting with two or more coats of synthetic enamel paint of required

shade complete as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN

1.6 rating with bronze/gunmetal seat dulyISI marked complete with

11 nuts, bolts, washers, gaskets conforming to IS 13095 of following

sizes as required :

Providing, installation, testing and commissioning of non-return valve

14 of following sizes confirming to IS: 5312 complete with rubber gasket,

GI bolts, nuts, washers etc.as required

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63

16 mm dia male and female couplings duly bound with GI wire, rivets

etc. conforming to IS 636 (type-A) as required

Supplying and fixing first-aid Hose Reel with MS construction spray

painted in post office red, conforming to IS 884 complete with the

following asrequired.20 mm nominal internal dia water hose

17.1 thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm

nominal internal dia gun metal globe valve & nozzle.Drum and

brackets for fixing the equipmets on wall.Connections from riser with

25 mm dia stop gun metal valve & M.S. Pipe and socket.

Providing & fixing indoor type hose lockable cabinet frames

fabricated from 40mm x 40mm x 5mm angle iron sections and 16

gauge MS sheet with full front glass door and locking arrangement,

suitable to accommodate landing valves, 15 m long hoses, first-aid

NSRFP-3 hose reel and branch pipe nozzle & fire mans’ axe. The cabinet No. 56.00 2500 140000.00

frame shall be painted with one coat of primer and two or more coats

of synthetic enamel paint of approved make and shade, as required

(Approx 2.1 m (high) x 0.9 m (wide). The item shall be complete of

MS housing with front door.

NSRFP-2 Providing and fixing standard firemans axe with heavy rubber handle. No. 56.00 750 42000.00

Cost shall be inclusive of providing break glass box containing key

for the cabinet along with hamer)

Providing and fixing heavy duty SS Floor grating with frame of

approved design including setting in floor with cement motor to match

with floor finish as per architect requirement. (for FHC drain pipe)

Digitally signed by ANUJ

ITEM No. AMOUNT (in Rs.) AMOUNT (in

Description of Items Unit QUANTITY RATE (in Rs.)

(DSR/MR) (DSR) Rs.) (NON- DSR)

Supply, Installation, Fixing of CO2 type Fire Extinguisher of capacity

4.5 kg confirms to IS 15683, bearing ISI mark, consisting of High

Pressure seamless steel cylinder (IS 7285) and duly approved by

NSRFP-7 Chief controller of Explosive Nagpur, fitted with wheel type valve, fully Each 56.00 5000 280000.00

charged with CO2 gas (IS 15222), with non-conductor of electricity

discharge PVC horn along with Bend Pipe, internally siphon tube &

mounting brackets having fire rating.

Supply, Installation, Fixing of Stored Pressure (ABC Dry Chemical

Powder) type Fire Extinguisher of Capacity 9 kg Confirms to IS

15683, bearing ISI mark complete with brass forged squeeze grip

type valve fitted with pressure gauge , pressurize with dry Nitrogen

gas filled, with discharge nozzle with wall mounting bracket, having

fire rating of 3A & 21B.

Mechanical Foam type Fire Extinguisher. In HP Mild Steel Cylinders

ISI marked TAC approved fitted with pressure indicating gauge,

internal tube, squeeze lever type valve fully charged complete in all

respects including wall suspension bracket / trolley mounted and

confoming to IS:910

NSRFP-10 50 Litres (trolley mounted) No. 4.00 15000 60000.00

TOTAL (DSR/NON-DSR) 423487960.25 70836614.29

GRAND TOTAL 494324575.00

GRAND TOTAL 494324575.00

Digitally signed by ANUJ