Construction of Commercial complex at Hosur in Krishnagiri district

Amount

Earth work excavation for foundation in all soils and sub-soils to the required depth as may be directed except in hard rock requiring blasting but inclusive of shoring, strutting, and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in 150mm thick layers well watered rammed and consolidated and depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metres and lift as specified here under etc. complete in all respects complying with relevant standard specifications and as directed by Dept.Officers excluding refilling. (OPEN EXCAVATION)

Upto 0.00 to 2.00M depth

Depth 2m to 3m

Depth 3 to 4m

Depth 4 to 5m

Supplying and filling in foundation and basement with stone dust of 150mm thickness well watered rammed and consolidated complying with relevant standard specifications including cost of filling M Sand as directed by the Departmental officers.

Refilling with excavated soil (other than sand) complete in all respects complying with relevant standard specifications and as directed by Dept.Officers

Cement concrete 1:4:8 (One of cement, four of M sand and eight of hard broken stone jelly) for foundation using 40 mm size broken stone jelly inclusive of shoring, strutting, baling out water wherever necessary ramming, curing etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.and as directed by the departmental officers.

Providing Form work and centering for reinforced cement concrete works including supports and strutting up to 3.30m height for plane surfaces as detailed below with all cross bracings using mild steel sheets of size 90cm x 60cm and MS 10 gauge stiffened with welded mild steel angles of size 25mmx25mmx3mm for boarding laid over silver oak or country wood joists of size 10cmx6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced at 75cm intervals and removing the same after a specified period without damaging the R.C.C works etc., complete complying with standard specifaction and as directed by the departmental officers.

For R.C.C. works in foundation and basement such as pile cap grid beam ,plinth beam, raft beam ,raft slab, column base, column footings complete all etc, complying with relevant standard specification and as directed by departmental officers.

Providing form work in Small Quantites etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Providing form work for plain surfaces such as floor slab, roof slab, beam etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Providing form work FOR VERTICAL WALL etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers.

Cement concrete 1:2:4 (One of cement, two of Msand and four of Hard broken stone jelly) for all RCC works namely Tee, Ell-rectangular beams, lintel, parapet cum drops, waist and landing slab, canophy, circular column, fin projections, sunshades, window boxing slab, loft and other similar works using 20mm gauge hard broken stone jelly excluding the cost and fabrication of reinforcement grills, shuttering and centering but including vibrating, laying, curing and finishing etc., complying with relevant standard specifications and as directed by the Departmental Officers in Foundation Basement .

Providing and laying in position Standardised, standardised concrete mix M30 Grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recomended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about(5.0 cum) 7730 KG OF 20mm machine crushed stone jelly with about (3.3 CUM) 5156 kg of 10 -12mm machine crushed stone jelly with about(4.79 CUM) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering including laying,manufctured in fully automatic batching plant and transported to site of work in transit mixer for all leads, vibrating with mechanical vibrators , finishing, curing, etc., and providing fixtures like fan clamps in the RCC Floor / RCC slabs wherever necessary without claiming extra etc, complete complying with standard specification and as directed by the department officers. the coarse and fine aggregates to be used should comply with the requirements of IS standards (No seperate payment will be made by the department for the excess usage of materials). The Design Mix should be got approved by the Chief Engineer before executing of work

Foundation & Basement

Ground Floor

First Floor

Second Floor

Third (Terrace) Floor

Supplying, fabricating and placeing in position of Mild steel/Ribbed Tor steel grills for reinforcement for all RCC works in all floors including the cost of binding wire, bending, tying, etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Fly Ash Bricks 1:5 ( One of cement and Five of M Sand) using Brick size 9"x4-3/8"x2-3/4" -(23x11x7 cm) having crushing strength of 50Kg/sqcm in foundation &basement including dewatering wherever necessary proper setting curing etc., complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers.

Foundation & Basement

Fly Ash Bricks 1:6 ( One of cement and six of M Sand) using Brick size 9"x4-3/8"x2-3/4" -(23x11x7 cm having crushing strength of 50Kg/sqcm in super structures including dewatering wherever necessary proper setting curing etc., complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers.

Ground Floor

First Floor

Second Floor

Third (Terrace) Floor

Fly Ash Brick Partition wall using Cement Mortar 1:4 (one of Cement and Four of M. Sand) 114mm thick using Third Class Kiln Burnt Country bricks of size 9"x4-3/8"x2-3/4" -(23x11x7 cm) having crushing strength of 50Kg/sqcm wherever necessary proper setting curing etc., complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers.

Ground Floor

First Floor

Second Floor

Plastering in C.M 1:3 (one of cement and three of P sand) 10mm thick for bottom of sunshade, ceiling in all floors, including hacking the RCC surface, providing necessary water bond using same mortar mix wherever necessary and scaffolding, curing ,finishing etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers.

Plastering in C.M 1:5 (One of cement and five of P sand) 12mm thick finished with neat cement including, providing band cornice scaffolding curing etc., complete complying with relevant standard specification and as directed by the departmental officer

Supplying and fixing of Double charged vetrified tiles of size 800 mm x800 mm x 10mm of best approved quality and colour laid in cement mortar 1:3 (One of Cement and three of M Sand) 10mm thick and pointed with coloured cement neatly including cost of Tiles, cutting and laying etc all complete complying with relevant standard specification and as directed by the departmental officers. The Design and Brand should be got approved by the Chief Engineer before executing of work.

Supplying and fixing of super fine polished Jet Black granite slab of 18 mm to 20 mm thick of approved quality laid in CM 1:3 (one of cement and three of Msand) 12 mm thick over slab including cutting the granite slab to the required size where ever necessary, nosing the edges to the required shape including cost of granite slab, polishing laying finishing etc all complete in all respects and as directed by the departmental offficers. (Measurement will be taken including bearing also The quality and color of Granite slab shall be got approved by the Chief Engineer before executing of work.

Supplying and fixing of colour Ceramic Anti skid Tiles of size 305x305x6mm without corrugated design for flooring and other similar works of best approved quality, colour and shade laid over cement mortor 1:3 (One of cement and three of M Sand) 20mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with white cement, curing, finishing etc., all complete and as directed by the departmental officers. The Design and Brand should be got approved by the Chief Engineer before executing of work.

Supplying and fixing of Colour glazed wall tiles of size 1500x150x6mm of best approved quality laid over cement mortar 1:2 (One of cement and two of M Sand) 10mm thick including fixing in position, cutting the tiles to the required size wherever necessary, pointing the joints with coloured cement, curing, finishing etc., all complete and as directed by the departmental officer. The Design and Brand should be got approved by the Chief Engineer before executing of work.

Weathering course with broken brick jelly lime concrete using 20mm gauge broken brick jelly in pure burnt limestone slaked and screened ( no M Sand) over roof slab to the proportion of brick jelly to lime (Fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters, for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers.

Finishing the top of terrace floor with one course of solar reflective water proof, heat proof, cool proof tiles of size 300mm x 300mm x 8mm of approved quality laid in cement mortar 1:3 (One part of cement and three part of M Sand) mixed with chemical mineral powder (60 kg for 1000 Sqft) (before laying tiles, the tiles should be dipped with salin based nano liquid) and top pointing with cement mortar 1:3 (One part of cement and three part of M Sand) mixed with white cement, silicon powder and polymer additives (20Kg of 1000 Sqft) and joint pointed with a base concrete of PCC 1:2:4 using 6 to 10 mm metal for providing necessary gradient at top of roof etc., complete complying with standard specifications including cost of all materials, labour charges for lifting to open terrace, laying and finishing and other incidental charges etc., complete and as directed by the departmental officers.The Design and Brand should be got approved by the Chief Engineer before executing of work.

Supplying and erecting pull and push type rolling shutter with I.S.I. make of approved size and section using 18 gauge G.I.sheet with manually operated type. The Shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc, complete as per standard specification. (SOR -2023-24 item no M-0401 - Page No - 49)

Supply and Fixing of Fire rated door with frame having Shutter thickness of 40mm,Material (steel), Lock set – dead lock with both side key, Powdered coated with RAL paint,fire resistant capacity upto 60 minutes. The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, pastering, Scaffolding all other conveyence etc complete complying with standard specification and as directed by the departmental officers.

Supply and Fixing of Wood Polymer Composite Board (WPC) solid door frame and 25mm thick shutter, the frame consists of extruded with size 75mm x 50mm. The inner core made of rigid WPC compound with minimum shore hardness of 55 and Bulk Density 0.8 Grms/Cub.C.Mt. The Frame shall be fixed to the wall using 10 x 100mm long MS Screw through the frame by using PVC fasteners A minimum of 3nos screws to be provided for each vertical member. The overall size of frames shall be with suitable rebate for housing the shutters and the shutters consists of 25mm thick Polymer Composite Board (WPC) single core Extruded door shutter, with one side digital Embo printing design. To avoid duplication, the printing design shall have the logo of the WPC brand approved by the Chief Engineer before executing the work.

supplying and fixing of T.W. Wrought and put up for frames of doors, windows, ventilators, cupboard and any other similar joineries works with necessary plugs, rebates for shutters plaster grooves on all faces etc., including labour charges for fixing hold fasts, complying with relevant standard specifications etc., in all respects and as directed by the Departmental officers.

Best indian teak wood up to 2.0 m

Best indian teak wood 2.00 to 3.00 meter

Supplying and fixing of Teak wood fully panelled door shutters with 7.5x3.75cm styles and rails 10x3.75 cm lock and bottom rails and 1.875cm thick planks for panels in the frame already provided including the charges for fixing of Brass furniture fittings such as 150mm handle with screws 1no., 125mm Butt hinges 3nos., 150x15mm Towerbolt 2nos., 250x16mm Aldrop 1no., Nylonbush 1no., Door stopper 1no., required brass screws etc., with ISI mark etc., complete complying with relevant standard specifications and as directed by the departmental officers.

Supplying and fixing of Solid core flush shutter with commercial ply on both sides with teak wood lipping alround 35mm thick etc., including cost and fixing charges for aluminium furniture fittings 125mm Butt hinges 3nos., 150x15mm Towerbolt 2nos., 250x16mm Aldrop 1no., Nylonbush 1no., Door stopper 1no., required brass screws etc., with ISI mark etc., complete complying with relevant standard specifications and as directed by the departmental officers.

Supply and fixing of best approved superior variety magnetic door catches suitable for doors including cost of door catches, Aluminium / Stainless steel screws fixing in position etc complete and as directed by the departmental officers. (BER No 24 /2019-20)

Supplying of Mild steel hold fasts horizontally twisted of size 230x40x4mm with pair of suitable iron screws of aproved quality and as directed by the departmental officers.All the material used in the construction are approved Brand /reputed Brand as per agreement condition.

Supplying and fixing Mild Steel grills as per the design approved to window, verandah enclosure or gate including one coat of primer and labour for fixing in position etc. all complete in all respects complying with relevant standard specification and as directed by the departmental oficers.The grill Design should be got approved by the Chief Engineer before executing of work.

UPVC Ventilator: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi hambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. (SOR -2023-24 item no M-0675 - Page No - 71)

UPVC Window: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The Design and Brand should be got approved by the Chief Engineer before executing of work. (SOR -2023-24 item no M-0674 - Page No - 70)

Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer (SOR -2023-24 item no M-0658 - Page No - 63)

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of „D‟ quality, galvanized as per IS277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS875. The Design and Brand should be got approved by the Chief Engineer before executing of work. (PWD SR -2023-24, Pg No - 68, M-0671)

Supplying and fixing Glass Partition as per requirements with glass door as per requirements with the following specifications: The partition and door is made of Saint Gobain / Asahi make glass 12 mm tk clear toughened glass with floor spring BT-SI Ozone make, single connector cum double connector patch lock fitting Ozone make and the partition is attached to the existing masonry or concrete structures with 789 weather sealant and other accessories, etc all complete as per standard specifications and as directed by the departmental officers

White washing three coats using clean shell lime slacked and screened including cost of lime, gum, blue brushes, scaffolding etc., complete in all respects and as directed by the departmental officers.

Painting the new walls with two coats of approved Interior Plastic emulsion paint over one coat of primer including cost of brushes, cement paints scaffolding curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. (The quality and shade of paint should be got approved by the Chief Engineer before execution of work).

Providing two coats putty for the walls including cost of putty, labour charges , scaffolding etc., complete complying with relevant standard specification and as directed by the departmental officer.

Painting the new walls two coats with best approved quality weather shield exterior emulsion paint over one coat of primer including cost of brushes, emulsion paints scaffolding curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. (The quality and shade of paint should be got approved by the Chief Engineer before use).

Painting new wood work with two coats of approved I st class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade. The paint should be supplied by the contractor at his own cost. (The quality and shade of paint should be got approved from CE before use on works) etc., complete in all respects, complying with relevant standard specifications.

Painting new iron work with two coats of approved Ist class synthetic enamel ready mixed paint in addition to one coat of primer of approved quality and shade. The paint should be supplied by the contractor at his own cost. (The quality and shade of paint should be got approved from Competent authority before use on works) etc., complete in all respects, complying with relevant standard specifications and as directed by the departmental officers.

Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.,complete.The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls. The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II)/1981 and as directed by the departmental officers. (BER 24 / 2019-20)

Supplying and fixing in position of stainless steel hand rails with Balustarder for stair case with top hand railing pipe of 50.80 mm dia with 40mm vertical post at 1000mm interval to a height of 1200 mm with horizontal support fabrication pipes of 38.30 mm dia - 3 line, pipe design with 12 mm dia pipe connecting two vertical and bottom horizontal pipes and fixing 100 mm dia ring with 12 mm dia base cup for every vertical post all stain less steel pipes are 1.60 mm thick pipe, 304G to be fixed and fabrication with gas tungsten arc welding, fixing with lock fix paste and cleaning with passivation paste to remove the welding film with fine polishing including drilling the tiles or granite including conveyance, loading unloading etc all complete complying with relevant standard specification and as directed by the departmental officers. (The quality of all the materials should be got approved before use on works) (SOR 2023-24 -Item no -M 0651 - pg no: 62)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of tubular 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete. (SOR 2023-24 -Item no -M 0652 - pg no: 62)

Providing 150mm, 75mm, 50mm band with cement mortar 1:5 (one of cement and five of M sand ) 12 mm thick finished with neat including, scaffloding, curing etc., complete complying with relevant standard specification and as directed by the departmental officers

Water Supply and Sanitary Arrangements

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition,etc., complete complying with standard specifications.The Design, Quality and Brand should be got approved by the Chief Engineer before executing of work. (SOR 2023-24 - Item No : M-0647, Pg No: 61)

Supplying and fixing of the Lipped Mouth white Porcelain Flat Back Urinal with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc. The Design, Quality and Brand should be got approved by the Chief Engineer before executing of work. (SOR 2023-24 - Item No : M-0553, Pg No: 55)

Supplying and fixing of porcelain wash basin superior variety of approved quality of size 550mm x 400mm (22" x 16") including cost and fixing of CI brackets, PVC waste pipe, CP tap, wheel/angle valve, pvc, connection, CP waste plug, with stainless steel chain etc., complete complying with relevant standard specifications in all respects as directed by the departmental officers. (The quality and brand of Wash basin and accessories shall be got approved from the CE before supply) (SOR 2023-24 - Item No : M--0544, Pg-55)

Supplying and fixing of 110mm dia PVC SWR pipe A Type for Rain water down fall pipe conforming to IS13592 with ISI mark and fittings conforming to IS 14735 , with necessary C I gratings, shoes, bends, offset ,clamp, teak wood plug, GI Bolts and Nuts, etc., of approved quality and including fixing C.I. gratings at the junction of parapet and floor or roof slab , including finishing etc., complete complying with relevant standard specifications. and as directed by the departmental officers.

Supplying, laying, fixing and jointing the following 50mm dia PVC pipes as per schedulespecials like Elbow, Tee reducers, Plug , union, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required below the ground level including earth work excavation or laying the pipes and refilling the trenches after the pipes are laid under ground etc., complying with relevant standard specifications & as directed by the departmental officers. (Below G.L) 50mm dia PVC pipe with necessary PVC/GI specials (Below G.L)

Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D – 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials like Elbow, Tee reducers, Plug , union, bend, coupler, nipple, MS Clamps etc., wherever required above ground level including the cost of Teflon tape, special clamps, GI Bolts and Nuts, nails, etc., fixing on wall to the proper gradient and alignment and redoing the chipped masonry after the pipes are laid etc., complying with relevant standard specifications & as directed by the departmental officers.

32mm dia ASTM-D schedule 40threaded Pvc pipe with necessary PVC/GI specials (From sump to tank)

25mm dia ASTM-D schedule 40threaded Pvc pipe with necessary PVC/GI specials

20mm dia ASTM-D schedule 40threaded Pvc pipe with necessary PVC/GI specials

Supplying and fixing of GM Gate valve 40 mm Dia heavy duty labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Competent authority before use).

20mm Dia

25mm Dia

50mm Dia

Supplying and fixing of C.P Bip cock Short body with wall flange like ESSCO, Jaquar fitiing including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from CE before use). (BER. 24/2019-20) Item No 511

Supplying and fixing of C.P Bip cock Long body with wall flange like ESSCO, Jaquar fitiing including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from CE before use). (BER. 24/2019-20) Item No 511

Supplying and fixing of Concealed stop cock Fitting including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from CE before use). (BER. 24/2019-20)

Supplying and fixing of Health faucet and Two Way CP Tap including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Competent authority before use). (SOR -2023-24, M-0515, Pg-53)

Supplying and fixing the following dia PVC (SWR) pipe type B class conforming to IS 13592and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary GI Bolts and Nuts with special clamp made of MS angle/Flat including cutting, bending (excluding the cost of MS angle/flat) holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc., complete complying with relevant standard specifications in all respects and as directed by the departmental officers.

110mm dia Pipe

75mm dia Pipe

Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of Msand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 115 mm thick using Second class chamber burnt ground mould bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) in cm 1:5 (One of cement and five of Msand ) plastered with CM 1:3 (One of cement and three of Psand) 12mm thick etc., complete complying with relevant standard specification and as directed by the departmental officers.

Construction of Inspection chamber with brick jelly concrete 1:8:16 (one of cement eight of M sand and sixteen of hard broken jelly) using 40mm gauge broken brickjelly 15cm thick for foundation and 23cm thick brick masonry in C.M. 1:5 (One of cement and five of Msand) using II nd class ground moulded Chamber burnt bricks of size 9”x4-3/8”x2-3/4” plastering with cement mortar 1:3 ( One of cement and three of Psand) 12mm thick on both sides top and bottom including earth work excavation, supply and fixing of SFRC cover slab of size 60cmX60cm including benching charnelling fixing cover slab in position curing finishing etc., complete in all respects.complying with relevant standard specification and as directed by the departmental officers.

Supplying and fixing best approved quality Brass C.P / Al anodised Towel rail 600mm. long and 20mm Diameter with brackets of same material including cost of Teak-Wood plugs and C.P.Screws etc., complete complying with standard specifications. (SOR-2023-24, M -0563) P-56

Supplying and fixing best approved quality C.P.Soap Tray of size 150mm X 100mm including cost of Teak Woodplugs, brass screws complete complying with standard specifications. (SOR-2023-24, M -0562) P-56

Supplying and fixing of PVC Nahani Trap not less than 110x75mm 4 way / 2 way (Superior variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amendments including resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of Msand & ten of 40 mm gauge brick jelly) etc., complete complying with relevant standard specification and as directed by the departmental officers (The PVC Nahani Trap should be got approved from the Competent authority before use) .

Providing Polimer coating (water proof Coating) For Sunken portion of toilets with the follwing specifications and the surface shall be cleaned to remove all dust, foreign matters loose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymenr liquid blend shall be mixed in to the desired ratio as per the recommendation of the supplier. The Mix Shall be Stirred throughly untill no bubble in the Mix Shall be removed.. Apply First Coat of Polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second Coat shall be applied on the first coat as directed by the departmental officer m-0625 SR 2023-24 P-60

Electrical Work

For light point controlled by 6 amps flush type switch: Wiring with 2 x 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI with suitable size MS box of 16 gauge thick concealed for light point controlled by 6 amps madular type switch including circuit mains cost of all materials, specials etc., all complete complying with relevant standard specifications and as directed by the departmental officers...

Light point with Ceiling Rose

Light point without Ceiling Rose with backlite battern holder

For Fan point controlled by 6 amps flush type switch with fan regulator: Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16g thick concealed and covered with for Fan point controlled by 6 amps modular type switch with fan regulator including circuit mains, cost of all materials, specials, etc., complete complying with relevant standard specification and as directed by the departmental officer.

Supply anf fixing of best approved superior quality concealed fiber box with MS Fan Hook of 100 mm dia 75 mm depth 3mm thick including cost of fixing in possition etc all complete as directed by the Departmental Officers. (The Brand/Model of the fan Hook has to be got approved by the Competent authority before fixing) SOR - 2023-24, M-1324

For Two way Light Point controlled by 6 amps madular type two way switch: Wiring with 3 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS Box of 16 gauge thick concealed and covered with for Two way Light Point controlled by 6 amps madular type two way switch including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers.

For 6 amps 5 pin plug socket point at Switch Board Itself : Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 gauge thick concealed and covered for 6 amps 5 pin plug socket point at Switch Board Itself including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers.

For 6 amps 5 pin plug socket point at convenient place: Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS box of 16 gauge thick concealed and covered for 6 amps 5 pin plug socket point at convenient place including circuit mains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers..

Supplying and fixing 16AMPS 3 pin plug type socket and switch on a suitable MS box 16g thick concealed and covered with madular switch inclusive of all connections and cost of all materials all complete, complying with relevant standard specifications & as directed by the departmental officers.

Supplying, fixing, connecting and commissioning of 32AMPS Metal clad socket for Air Conditioner (Superior variety) ( Three phase)combined with 25AMPS SP MCB in Manufactures mount box fixed madular with the wall including cost of material, necessary interconnection etc, switch on suitable angle Iron frame work with necessary earthing etc., all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Competent authority before use). (BER-16/20-21)

Supplying and fixing of water tight Bulk head fittings with One number of 11 Watts CFL BULB including necessary connections, cost of materials etc., all complete complying with relevant standard specifications & as directed by the departmental officers. (The Brand/Quality of fittings and CFL Lamp has to be got approved by the CE before fixing) .

Supplying and fixing concealing of MS box of size 8" x 6" x 3" concealed TV/Telephone Junction connection including necessary materials etc all complete in all respects.

Supplying laying and concealing of 20 mm PVC pipes with necessary specials and other materials including run off 1no.fishwire (GI 22 G) for drawing cable for TV and telephone etc., all complete as directed by departmental officers.

Supplying and concealing TV/ Telephone socket with top pin with suitable Teak wood box fully concealed and covered etc., all complete as directedy the Departmental officers

Supply and fixing 36W 4 Feet Tube light fitting with bulb on wall all complete complying with relevant standard specifications & as directed by the departmental officers.(The Tube light fitting and bulb should be of reputed Brand and it should be got approved by the Competent authority before fixing). SOR - 2023-24, M-1211, Pg-118

Supply and fixing of 7 segment Three Tier Three Phase Vertical Distribution Board with 6 way per Phase, 63 Amps 4 Pole MCB - 1No., 63 Amps DP MCB - 3No ., 20Amps SP 10 KA MCB - 18 No etc., complete complying with standard Specification and as directed by the departmental officer. (BER-16/20-21)

Supplying and fixing of FOUR POLE 40amps rating three phase Earth Leakage Circuit Breaker/Residual Current Circuit Breaker (ELCB/RCCB) 30 MA sensitive with ISI mark on fully concealed suitable MS box with necessary interconnection and earth connection using copper cable including the cost of materials,conveyance and redoing the disturbed portion etc all complete. (BER-16/20-21)

Run of main with 2 wires of 2.5 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Run of main with 2 wires of 4 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Run of main with 4 wires of 4 Sqmm Copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 32mm dia rigid PVC conduit pipe with ISI mark etc., including cost of all materials, specials etc. all complete and as directed by the departmental officers.

Supplying and laying of 8 SWG GI wire on walls/below G.L. with necessary "U" nails earth work excavation and refilling etc., including cost of all materials etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Providing earthing station using pipe electrode as per IS 3043( For MSB Standard) using 40mm dia B Glass G.I pipe 2.5 meters. 20mm dia B class G.I. pipe 1 metre 40 x 20mm G.I. Reducer 1 no.1 set of funel G.I. nuts, bolts, washers and checknuts, 40Kg charcoal, 2nos.of C.I.bend 15mm dia 4 Nos.of 15mm dia G.I. coupling and 10Kg salt including necessary earth work excavation (i.e. by augering 30cm dia to a depth of 3.5 metres.and laying the salt and charcoal in layer by layer around G.I.pipe brick work in Cement mortar and plastering and Caver by SFRC Cover Haevy duty of size 300x300mm etc . Including cost of all materials and labour in accordance with IS 3043. etc. all complete in all respects complying with relevant standard specification and as directed by the departmental officer.

Supplying and fixing of wall mount street light with one number of 30 W LED including 20mm GI pipe B Class of 2m length with required screw, bolt, nuts, 8m lrngth of 2.50Sqmm PVC unsheathed mult core copper cable with ISI mark etc.,complete with ISI mark, complying with relevant standard specifications & as directed by the departmental officers. (The Brand/Quality of fittings and Lamp has to be got approved by the CE before fixing).

Supply and Laying of PVC armoured LTUG cable of 3 1/2 core 50 Sq.mm Aluminium in a trench to be excavated at a depth of 0.75m putting 0.15m layer of sand and covering three sides of the with bricks and refiiling etc., all complete and as directed by departmental officers. ( Below GL )

Supply and Laying of PVC armoured LTUG cable of 3 1/2 core 25 Sq.mm Aluminium in a trench to be excavated at a depth of 0.75m putting 0.15m layer of sand and covering three sides of the with bricks and refiiling etc., all complete and as directed by departmental officers. ( Below GL )

Supply and Laying of PVC armoured LTUG cable of 3 1/2 core 185 Sq.mm Aluminium in a trench to be excavated at a depth of 0.75m putting 0.15m layer of sand and covering three sides of the with bricks and refiiling etc., all complete and as directed by departmental officers. ( Below GL )

Cement concrete 1:11/2:3 (One of cement, one and half of Msand and three of Hard broken stone jelly) for all RCC works namely Tee, Ell-rectangular beams, lintel, parapet cum drops, waist and landing slab, canophy, circular column, fin projections, sunshades, window boxing slab, loft and other similar works using 20mm gauge hard broken stone jelly excluding the cost and fabrication of reinforcement grills, shuttering and centering but including vibrating, laying, curing and finishing etc., complying with relevant standard specifications and as directed by the Departmental Officers in the following floors.

In Foundation and Basement

Plastering with CM 1:3 (One of Cement and Three of P Sand) 12mm thick mixed with water proofing compound at the rate of 2 Kg/10 sqm finished with neat cement including providing band cornice,ceiling cornice,curing,scaffolding etc,complete in all respects and complying with relevant standard specifications.

Supplying and fixing of C.I. steps of approved quality and brand including cost of material, labour charges for fixing etc., complete complying with relevant standard specification and as directed by the departmental officers. SR 2023-24, Pg No-62

Supplying and fixing of Manhole cover with locking arrangements of approved quality and brand of size 0.60x0.60 metre (20 Kg) (heavy duty with frame) including cost of material, labour charges for fixing etc., all complete and as directed by the departmental officers. SR 2023-24, Pg No-60, M-0640

Supply and delivery of Aluminium Ladder for all acceriories etc, Complete complying with relevant standard specification and as directed by Dept. officers. UGR., (BER No: 34/2020-21)

Supply & Planting Avenue trees including earthwork excavation for pit of size 60x60x60cm filled with manure for 20cm depth and filling with river sand and red earth mix in the ratio of 1:1 for 40cm depth in the same pit and planting the avenue trees of approved varities to a height of 200cm from the ground level and maintaining them for the period of 6 months including watering,periodical manuring and replacing the avenue trees if need etc., all complete and as directed by the departmental officres. (Tree scapping shall be got approved from the competent authority before use.including cost of Tree and maintenance charges etc., complete)

Supplying and fixing of chicken mesh Tree Guard using 8cm dia casurina vertical post and middle tie using country wood reeper of size 50x25mm and 25 gauge chicken mesh including labour charges for fixing the triangular tree guard and as directed by the departmental officers.

Providing Name board (letters) Aluminium powder coated letters size 450mm thickness 12mm hollow type Aluminium Dye casting with print and lamination english letters (Tamil letters -40 Nos) standard font. The rate including cost of fixing charges labours coveyance etc, all complete complying with relevant standard specifications and as directed by the departmental officer.

Providing TNHB Logo : 600mm dia 12mm Hallow Type Aluminium Die casting with print and lamination. The rate including cost of fixing charges labours, conveyances etc, all complete complying with relevant standard specifications and as directed by the departmental officers.The Design, Quality and Brand should be got approved by the Chief Engineer before executing of work.

Supplying and Laying Rubber Moulded paver block of 63mm thick using this cement concrete 1:1.5:3 (One cement One and half Msand and three aggregate) complete and as directed by the department officer.The rate is inclusive of labour charges for laying compacting using earth rammer,conveyence charges etc.. (SR 2023-24, Pg No-38)

Providing Borewell of 150 mm: Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site (Site will be shown by the TWAD Board Officers) including construction of mud pit. (TWAD Sr-2022-23, Pg -302, Item No 12.a)

Supply and delivery of 160 mm dia PVC casing pipe 6 Kg/Sq.cm as per IS 12818/1992 etc. all complete complying with relevant specification and as directed by the Departmental Officers. (The Brand and quality of pipe has to be got approved by the Competent authority before supply). (BER No 76 / 2019-20)

Supply and delivery of 160 mm dia PVC end cap with ISI mark all complete complying with relevant specification and as directed by the Departmental Officers.(The Brand and quality of pvc specials has to be got approved by the competent authority). TWAD SR -2022-23, Pg-27

Supply and delivery of Ductile Iron 150mm Dia SOCKET/SPIGOT Pipe and Specials as per Standard K9 flanged pipes B/I pipe ,D/F for sewer Pumping main as per IS 8329-2000 K9 flanged pipe.all complete complying with relevant specification and as directed by the Departmental Officers. TWAD SR -2023-24, Pg No 47

Labour charges for laying fixing and jointing DI pipes and specials of the following dia Below Ground level including cutting and threading the pipes wherever necessary and jointing with white lead, earth work excavation for laying the pipes, wrapping the pipes with tarred tape and refilling the trenches after the pipes are laid under ground etc., complete in all respects all complete complying with relevant standard specifications and as directed by the departmental officer.

Supply and delivery of 7.5 H.P Submersible pumpset for 150mm Dia Borewell with I.S.I mark complete all complying with relevant standard specifications and as directed by the departmental officer. (PWD SR -2023-24, Pg No -112, M-1069)

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days for 7.5 HP Submersible Pump Set all complete complying with relevant standard specifications and as directed by the departmental officer. (TWAD SR - 2022-23, Pg - 308)

Supply of 3 phase panel Board suitable for 7.5HP 15 stage submersible pumpset with DOL starter with 2 level guard autostart,3 phase preventer, dry running preventer etc.all complete complying with relevant specification and as directed by the Departmental Officers.

Supplying and Erection of 125KVA Generator (Kirloskar) diesel engine Model 4R 1040TA G1, four cylinders, liquid cooled, turbocharged with after cooler, developing 102 bhp @ 1500 RPM. 4R 1040TA G1 is Inline, electric start, compression ignition, 4 stroke, designed to run continuously at 1500 RPM confirming to IS 10002, ISO-3046, BS 5514 standard. Diesel Engine will comply with present CPCB - II norms. with AMF panel suitable for 100KVA DG set all complete complying with relevant specification and as directed by the Departmental Officers. (SOR 2023-24 - Pg No 157)

Supply and Laying of Aluminium Armoured Under Ground cable with ISI Mark of 3 1/2 core 70 Sq.mm in a trench to be excavated at a depth of 0.75m putting 0.15m layer of Msand and covering three sides of the with bricks and refiling etc., & brand should got approval from CE before laying., all complete and as directed by departmental officers. (Below GL).

Providing & Fixing of Exhaust Support 100 x 40 MS Channel and 10mm Plate etc., complete complying with standard specification and as directed by the departmental officers. (BER:30/21-22)

Providing & Fixing of Hanger Fastener Bolt & Nut etc., complete complying with standard specification and as directed by the departmental officers. (BER:30/21-22)

Providing & Fixing of Exhaust Pipe insulation 50mm Thick SWG 24KG Aluminium Sheet with mineral wool of required thickenness etc., complete complying with standard specification and as directed by the departmental officers. (BER:30/21-22)

Providing & Installation of Exhaust Pipe With Silencer etc., complete complying with standard specification and as directed by the departmental officers. (SOR 2023-24 - Item No : M-2085, Pg No: 157)

Finishing the top of flooring with cement concrete 1:3 (One of cement and three of blue granite chips of size 10mm, and below) 20 mm thick Ellis Pattern Flooring (No Sand) and surface rendered smooth including 150mm wide skirting, providing proper slopes, thread lining, curing etc.,all complete complying with relevant specification and as directed by the Departmental Officers.

Supplying & Fixing of 40mm UPVC (Unpolymer vinyle chloride) pipe with ISI standard all complete complying with relevant standard specifications and as directed by the departmental officer. (SOR 2023-24 item no - M-1077 pg no 112)

Supply of Nylone Rope for Bore well all complete complying with relevant standard specifications and as directed by the departmental officer. (SOR 2023-24 item no - M-1072 pg no 112)

Providing Rain water Harvesting pit by earth work of 90cm dia and 60 cm depth and filling with stone jelly 40mm size including earth work excavation filling work with the stone jelly and covering with precast RCC 1:2:4 slabs, precast well ring RCC 1:2:4 including cost of steel and fabrication of reinforcement and grills pre casting moulding, curing finishing and placed in position and auguring 300mm dia bore pit to a depth of 4.40m and filling the entire depth of bore pit using river sand 15% 20mm H.B Stone jelly 50% and 40mm H.B Stone jelly 35% including Supplying & fixing 1No. Gully trap with 110 mm dia PVC pipe for jointing including the cost of materials and labour charges etc all complete.

CCTV Arrangements

Supply, Installation, testing and Commissioning of 32 channel NVR, Supports decoding H.265+/H.265/H.264+/H.264 video formats,Up to 4K high-definition live view, Up to 320 Mbps high incoming bandwidth ensures IP cameras can be connected,storage and playback Internal HDD of 2SATA ports, 2 HDMI/VGA simultaneous video outputs, Supports various specific function cameras with all required Accessories (2 Nos of Hard Disk)

Supply and fixing of Hard Disk for NVR 8TB complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.166 Item No. 38, M - 2223)

Supply and fixing of PoE Switchs for CCTV IP Camera 24 Port complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.165 Item No. 33, M - 2194)

Supply and fixing of 6U Rack with Accessories complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.166 Item No. 39, M - 2226)

Supply and fixing of 42U Rack with Accessories complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.166 Item No. 39, M - 2230)

Supply and fixing of Unarmoured LAN & CCTV Cable (CAT 6) complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.164 Item No. 28, M - 2183)

Supply and fixing of Conduit pipe 25 mm dia heavy Gauge complete all etc complete complying with relevant standard specifications and as directed by the departmental officer. The Quality and Brand should be got approved by the Chief Engineer before executing of work. (PWD SOR 2023-2024 Pg No.135 Item No. VIII(I), M-1619)

Supply, Installation, testing and Commissioning of 1/2.8" 2MP Dome Camera , 1920x1080:30fps, H.265/H.264/MJPEG, Triple streams,DC12V & POE, Fixed Lens 2.8/3.6/4/6mm optional, IR Range 30 mtrs, Day & Night IR cut filter with auto switch, Efficient H.265+ compression technology to save bandwidth and storage,Clear imaging even against strong back light thanks to 120 dB true WDR technology,IP67 ingress protection level, Standard Video compression with high compression ratio and all the required accessories.

Supply and fixing of Camera Box with Connectors complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Supply and fixing of Professional 55" Smart LED Display complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Labour charges for laying the conduct pipe and cable complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Design, Manufacture, Supply and delivery, Erection, Testing and Commissioning of 13 Passenger capacity lift with power opreated center opening door with the following specifications. Brand of lift - Johnson/ Kone/OTIS/Equivalent Type of lift - Gearless Lift with Machine Room Number of floors - Basement +Stilt + 2 Floors Speed - 1m / Second with ARD. Grade - SS 304 (Stainless Steel ) Designation of Lifts - Passenger Elevator No of Elevators - 1 Nos Type and Capacity - 13P/884Kgs Speed - 1.00M/Sec Type of Drive - V3F Drive 65% Power saving Location of Machine room - Gearless with M/C RoomTravel - 12Mts approx.Serving - B+S+2 No of stops - 2 Nos Pit Depth - 1600 mm Head room - 2200 mm Car Size - 2000mm Width X 1100mm Depth Car Enclosure / Ceilng - SS Hairline Finish Car Flooring - PVC Flooring No of Entrance - Single Entrance Car Entrance - Center opening Automatic Power Door with SS Hairline finish

Design, Manufacture, Supply and delivery, Erection, Testing and Commissioning of 8 Passenger capacity lift with power opreated center opening door with the following specifications. Brand of lift - Johnson/ Kone/OTIS/Equivalent Type of lift - Gearless Lift with Machine Room Number of floors - Basement +Stilt + 2 Floors Speed - 1m / Second with ARD. Grade - SS 304 (Stainless Steel ) Designation of Lifts - Passenger Elevator No of Elevators - 1 Nos Type and Capacity - 8P/520Kgs Speed - 1.00M/Sec Type of Drive - V3F Drive 65% Power saving Location of Machine room - Gearless with M/C RoomTravel - 12Mts approx.Serving - B+S+2 No of stops - 3 Nos Pit Depth - 1600 mm Head room - 2200 mm Car Size - 2000mm Width X 1100mm Depth Car Enclosure / Ceilng - SS Hairline Finish Car Flooring - PVC Flooring No of Entrance - Single Entrance Car Entrance - Center opening Automatic Power Door with SS Hairline finish

Supply, Erection, Commissioning and testing of Solar Power Plant - ON Grid system: 5 KWp with various components and technical specification as specified here under including the comprehensive maintenance (CMC) for 5 years. a) Solar Photovoltaic Module as per MNRE standards SPV Panel Specifications: 5 KWp Modules - 25 years warranty. (As per MNRE standard test certificate should be enclosed) b) Solar Grid Tie Inverter with MPPT charge controller of capacity - 10KVA complete - 5 Years warranty. (As per MNRE standard test certificate should be enclosed). c) Mounting Structure & Electrical Accessories mounting structure design to withstand wind velocity to 150 Km/hr, Structure material - Hot dip galvanized steel with a minimum galvanization thickness of 120 microns or aluminium alloy, bolts, nuts, fasteners, panel mounting clamps stainless steel SS 304 Mounting arrangements for RCC - flat roof with PCC (1:2:4) as per MNRE standards. DISTRIBUTION BOARD, AC Distribution , Earthing protection, cables complete and as directed by the departmental officers.

Supply and Fixing of MS adopter to joint pipe line and pump set complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Supply and Fixing of 40mm PVC coupler complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Supply and fixing of 40mm pvc pipe for water supply from Borewell to Sump complete all etc complete complying with relevant standard specifications and as directed by the departmental officer.

Sub Total

SS Associates