Loading…
Loading…
Tender Value
₹1.6 Cr
EMD Value
₹3.2 L
Closing Date
28 May 2026, 5:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
DEN2
24 conditions · 4 needing a document upload
10.2. Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. ( Click here to download Format)
Each page of the copy of documents/certificates in support of Special Financial Criteria, submitted by the tenderer, shall be self attested/ digitally signed by the tenderer or authorized representative of the tendering firm. Self attestation shall include signature, stamp and date (on each page).
Note Explanation for clause 10 including 10.2 contractor may refer Indian Railways Standard General Conditions of Contract- April- 2022 (GCC April-2022).
Credentials if submitted in foreign currency shall be converted into Indian currency i.e., Indian Rupee as per clause 10.5 of Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022).
Eligiblity criteria: -10.1 (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b) (i) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i)Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii)One similar work each costing not less than the amount equal to 60% of advertised value of each component shall also be considered for fulfillment of technical eligibility criteria for different components. (b) (2) In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contract or through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfilment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows: The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. ( Click here to download Format)
Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of subcontractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note:- Substantially Completed Work :- Substantially Completed Work means an ongoing work in which payment equal to or more than 90% of the present contract value (excluding the payment made for adjustment of Price variation (PVC), if any) has been made to the contractor in that ongoing contract and no proceedings of termination of contract on Contractor's default has been initiated. The credential certificate in this regard should have been issued not prior to 60 days of date of invitation of present tender. Note for item 10.1: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company insupport of above work experience certificate.
Definition of Similar work : Any civil works. ( Click here to download Format)
The tenderer in support of his/their claim of qualifying the laid down "Technical Eligibility Criteria" must submit Experience Certificate a s per 1.1.2 format prescribed in Annexure "W" duly self attested/digitally signed on each page (Self Attestation shall include signature, date & stamp of the tenderer).
The copy of respective letter of acceptance/agreement for which experience certificate has been produced in Annexure-W is to be enclosed in support of "Similar Nature of Work". This document should be duly self attested/digitally signed on each page (Self Attestation shall include signature, date & stamp of the tenderer).
Tenderer has to submit details of employment/partnership etc. of Retired Railway Employees, as applicable, as per Para 16(a), 16(b) & 16(c) of Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips upto-date and as given in para 24.1 & 24.2 of "General Instructions to Tenderers for e-Tenders" attached with tender document. Tender submitted without the aforementioned sought information or tender submitted without a statement to the effect that no such retired Engineer or retired Gazetted Officer, as per Para 16(a), 16(b) & 16(c) of Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-todate, is so associated with the tenderer, as the case may be, shall be rejected. The format for providing the aforementioned sought information is given in Annexure-J in the attached documents with the tender. ( Click here to download Format)
Each page of the copy of the documents/ certificates in support of Special Technical Criteria, submitted by the tenderer, shall be duly self attested/digitally signed by the tenderer (Self Attestation shall include signature, date & stamp of the tenderer).
Note Explanation for clause 10 including 10.1, contractor may refer Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022).
Credentials if submitted in foreign currency shall be converted into Indian currency i.e., Indian Rupee as per clause 10.5 of Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022).
48 conditions
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
GENERAL INSTRUCTIONS TO TENDERERS For e-Tenders:-
E-tender have been invited for and on behalf of the President of India through website www.ireps.gov.in for the work mentioned against the tender notice number available in the website. Tenderers are required to bid online only in the above mentioned website. All Mandatory fields marked have to be filled in by the tenderer. No manual offer is acceptable against this tender. No Tender document in hard copy will b e sold against this tender. Please read the Instructions to Tenderers for e-tendering, Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date and Special Condition of Contract before filling the e tender through online.
E-Tender forms are not transferable and the same is to be submitted with digital signature by the Tenderer already registered with the site.
The submitted e-tender forms will b e considered a s digitally signed by the tenderer as a confirmation from the tenderer that the tenderer has read, agreed and accepted all the conditions and attached documents referred in para 1.2 above as well as Schedule of Tender, Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date and Special Conditions of Contract.
The tender offer complete in all respect and with all documents is to be submitted online by e-tendering process through the website www.ireps.gov.in before the closing time/date of this tender as mentioned in the NIT (Notice Inviting Tender). Tenderer can revise the bids any number of times till the closing time/date of the tender. No manual offers shall be accepted.
The Railway may, of its own or in response to any clarification requested/ suggested by any person including that from the tenderer, may modify this tender document at its sole discretion at least 15 days before the due date of closing of the tender as corrigendum.
Corrigendum as required may be issued at least 15 days prior to the closing of the tender. The corrigenda of this tender, if any, as issued time to time will be available on website at least 15 days in advance of closing of tender. The tenderers are requested to check the website before submitting their offer whether any such corrigendum to the tender has been issued or not and revise the offer if required accordingly. Failure on the part of tenderer on this aspect will be solely tenderers responsibility.
This document is the Standard Tender Document which consists of the General Instruction to Tenderers, NIT (Notice Inviting Tender), Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date, Special Conditions of Contract, Tender Schedules, Specifications of the works & various Annexures etc. All the above-mentioned documents taken together if not scored off, shall constitute the complete tender document here after referred to as "Tender Document" & have to be read together & acted upon accordingly. No part of the tender document can be relied upon or acted upon in isolation.
The Railway and the website will have no responsibility for incorrect evaluation of cost and thereby incorrect cost of work and ranking of tenderers, if the schedule is not filled correctly and unambiguously for each item. No claim or clarification of a tenderer regarding applicability, inclusion or exclusion of any element of tax or duty or any other change in the offer subsequently (after opening of the tender) will be entertained. For this the tenderers are advised to read the Instructions, Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date, Special Conditions of Contract and other Instructions carefully before submission of tender.
In case of any problem with the portal is faced while filling the e-tender, Tenderers are advised to contact with the Helpdesk of IREPS portal who will render all help and assistance related with the website and portal except that related with the details of the tender. Railway will not take any responsibility for nonparticipation in the e-tender online for the reasons related to the website and portal or server etc beyond the control of railways.
Railway and the IREPS website will not take the responsibility for any online payment made by the tenderer and debited from his/their account towards the Earnest Money due to wrong or mismanipulation or any reasons related with the IT or found unsuitable for the tender etc. In this regard Railway and IREPS website will not entertain any claim or refund the paid amount. E- Tender Forms shall be issued free of cost to all tenderers.
All documents uploaded or information furnished in the website are digitally signed by the competent authority.
INCONSISTENCY BETWEEN THE DOCUMENTS
The Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date, Standard Schedule of Rate SSOR), CPWD Specifications 2019 Vol I & II and the USSOR [Unified Standard Schedule of Rates (Labour & Materials) & Indian Railway Unified Standard Specification shall be read with all correction slips issued thereto from time to time and shall form integral part of this tender document. In case of any difference, contradiction, discrepancy, with regard to Conditions o f tender/contract, Specifications, Drawings, Bill of quantities etc., forming part of the tender/ contract, the following shall b e the order of precedence: (i) Letter of Award/Acceptance (LOA) (ii) Bill(s) of Quantities (iii) Special Conditions of Contract (iv) Technical Specifications as given in tender documents (v) Drawings (vi) Indian Railways Standard General Conditions of Contract updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents. (vii) Indian Railways Unified Standard Specification (IRUSS) updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents, if applicable in thecontract. (viii) CPWD Specifications Vol I & II updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents, if applicable in the contract. (ix) Indian Railways Unified Standard Specifications (Works and Material) updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents, if applicable in the contract. (x) IR Specifications/Guidelines updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents. (xi) Relevant B.I.S. Codes updated with correction slips issued up to date of inviting tender or as otherwise specified in the tender documents.
TENDERER S POSTAL ADDRESS
Address of tenderer: The address, email Id and Mobile phone, other phone nos. and other details given in the portal while registering will be considered as official address a n d all correspondences to the tenderer will be made in these registered modes. All communication sent in time to the tenderer by post at the said address shall be deemed to have reached the tenderer duly and in time. Important documents shall be sent by Registered Post. However, an undertaking has to be given in the enclosed annexure by uploading a scanned copy of duly filled in form in the portal.
THE SCHEDULE OF WORKS
The Schedules of Works is also available separately in the website online and Rates are to be quoted online and submitted online duly signed digitally.
INSPECTION OF DATA
Drawings for the work can be seen in The office inviting this tender on any working day during working hours. The drawings are only for the guidance of tenderers. Detailed working drawings, if required based on the drawings mentioned above, will be given by the Engineer or his representative from time to time.
OPENING OF TENDER
Opening of e-tender online:- The e-tenders will be opened online using the IREPS portal. No representative is required to be present for opening of tender and taking notes of rates quoted and ranking as the complete details of rates etc. of all the bidders shall be available to the bidders in the website after the opening of the tender. In case of two packet system, technical bids will be opened first and financial bid will be opened in a subsequent date and time to be notified/intimated to those bidder whose technical bids are found acceptable. The tenderer must submit the documents in support of technical bids against eligibility criteria as mentioned in special technical criteria at para 4 and filled the financial bid on schedule.
In case the date of closing mentioned in the Notice Inviting Tender is declared a holiday/bandh/strike etc. on any account, the date of closing tender online will not be changed as the application in the website of IREPS does not permit submission of any offer after closing date and time of the tender. However, opening of tenders online will be on any convenient day after the closing date/time of tenders.
SUBMISSION OF DOCUMENTS IN SUPPORT OF ELIGILIITY CRITERIA, IF APPLICABLE:-
All documents in support of fulfillment of the eligibility criteria with respect to completion of similar nature of work for Technical Eligibility Criteria and minimum average annual contractual turnover for Financial Eligibility Criteria must be uploaded over the website www.ireps.gov.in with scanned copy in .Pdf format at the time of tender bidding with details in specified format (Annexure W & VIB)
The tenderer shall submit along with the tender document, documents in support of his / their claim to fulfill the eligibility criteria as mentioned in the tender document. Each page of the copy of documents/certificates in support of credentials, submitted by the tenderer, shall be self- attested / digitally signed by the tenderer or authorized representative of the tendering firm. Self - attestation shall include signature, stamp and date (on each page).
The Railway reserves the right to verify all statements, information and documents submitted by the bidder in his tender offer, and the bidder shall, when so required by the Railway, make available all such information, evidence and documents as may be necessary for such verification. Any such verification or lack of such verification, by the railway shall not relieve the bidder of its obligations or liabilities here under nor will it affect any rights of the railway there under.
In case of any wrong information submitted by tenderer, the contract shall be terminated. Bid Security, Performance Guarantee (PG) and Security Deposit ( SD) of contract shall be forfeited and agency shall be debarred for doing business on entire Indian Railways for 2 (Two) years
Tenderer are advised to take utmost care while scanning/uploading the documents related to their eligibility. Railway administration will not be responsible for improperly scanned/uploaded document, corrupt file, illegible documents etc.
The tenderer should ensure that the information/documents, being submitted in support of claim of qualifying the laid down eligibility criteria, are prepared in prescribed formats duly signed by an official authorized to do so. Documents issuing authority must furnish all relevant information in the prescribed format itself. Complete details of issuing authority should also be indicated in the document. Furnishing incomplete, illegible, vague information may lead to rejection of offer.
SUBMISSION OF COST OF TENDER FORM:
E-Tender Forms shall be issued free of cost to all tenderers.
SUBMISSION OF Bid Security: The Bid Security shall be deposited either in cash through e-payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India. The Bank Guarantee bond shall be as per Annexure-VIA and shall be valid for a period of 90 days beyond the bid validity period.
Tender must be accompanied with Bid Security of requisite amount as mentioned in NIT in A/c of P.F.A., S.E.C.Railway, Bilaspur deposited through Internet Banking or payment gateway only. i Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Bid Security deposit detailed above. ii Labour Cooperative Societies shall deposit only 50% of above Bid Security deposit detailed above.
In case, submission of Bid Security in the form of Bank Guarantee, following shall be ensured:- i. A scanned copy of the Bank Guarantee shall be uploaded on e-Procurement Portal (IREPS) while applying to the tender. ii. The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document (i.e. Official Address mean: Divisional Engineer/II/Raipur, Office of the Sr. Divisional Engineer/Co-ord/Raipur, DRM office Complex, Near Waltair Gate, P.O- WRS Colony, Raipur, Chhattisgarh-492008) before closing date for submission of bids (i.e. excluding the last date of submission of bids). iii. Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. iv. The Tender Security shall remain valid for a period of 90 days beyond the validity period for the Tender. v. The details of the BG, physically submitted should match with the details available in the scanned copy and the data entered during bid submission time, failing which the bid will be rejected vi. The Bank Guarantee shall be placed in an envelope, which shall be sealed. The envelope shall clearly bear the identification "Bid for the ***** Project" and shall clearly indicate the name and address of the Bidder. In addition, the Bid Due Date should be indicated on the right hand top corner of the envelope. vii. The envelope shall be addressed to the officer and address as mentioned in the tender document. viii. If the envelope is not sealed and marked as instructed above, the Railway assumes no responsibility for the misplacement or premature opening of the contents of the Bid submitted and consequent losses, if any, suffered by the Bidder.
SOUTH EAST CENTRAL RAILWAY TENDER FORMS (FIRST SHEET) ANNEXURE-I
I/We have read the various conditions to tender attached hereto and agree to abide by the said conditions. I/We also agree to keep this offer open for acceptance for a period of 60 (Sixty days) days from the date fixed for closing of the tender and in default thereof, I/we will be liable for forfeiture of my/our "Bid Security". I/We offer to do the work for South East Central Railway, at the rates quoted in the attached bill(s) of quantities and hereby bind myself/ourselves to complete the work in all respects within as mentioned in NIT of this instant tender (months) from the date of issue of letter of acceptance of the tender.
I/We also hereby agree to abide by the Indian Railways Indian Railways Standard General Conditions of Contract- April- 2022 (GCC-April-2022) with all correction slips up-to-date and to carry out the work according to the Special Conditions of Contract and Specifications of materials and works as laid down by Railway in the annexed Special Conditions/Specifications, Schedule of Rates with all correction slips up-to-date for the present contract.
A Bid Security of Rs. (as mentioned in NIT of this instant tender) has already been deposited online/ submitted as Bank Guarantee bond. Full value of the Bid Security shall stand forfeited without prejudice to any other right or remedies in case my/our tender is accepted and if: -
I/We do not submit the Performance Guarantee within the time specified in the Tender document;
I/We do not execute the contract documents within seven days 10.3.2 after receipt of notice issued by the Railway that such documents are ready, and
I/We do not commence the work within fifteen days after receipt of orders to that effect.
( a ) I/We am/are a Start up firm registered by........................ Department of Industrial Policy and Promotion (DIPP) and my registration number is................ valid upto...................... (Copy enclosed) and hence exempted from submission of Bid Security.
We are a Labour Cooperative Society and our Registration No. is .................... with .......................and hence required to deposit only 50% of Bid Security.
Until a formal agreement is prepared and executed, acceptance of this tender shall constitute a binding contract between us subject to modifications, as maybe mutually agreed to between us and indicated in the letter of acceptance of my/our offer for this work.
TENDER FORM (SECOND SHEET) ANNEXURE-I
Instructions to tenderers and conditions of tender: -The following documents form part of Tender/Contract:
Construction of New Officers' Rest House (4 Suites, 6 Deluxe rooms and 2 Dormitories) at WRS Colony, Raipur.
E-R-T-30-26-27
E-R-T-30-26-27
Open
Works - General
12 Months
Raipur, Chhattisgarh
₹0
₹3.2 L
28 May 2026
5 May 2026
14 May 2026
274 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | Above/ 13978571.64 Below/P | ||
| — | 50.00 | — | — | ||
| Earth work in excavation as per approved drawings and dumping at embankment site or spoil heap, within railway land, including 50m lead and 1.5m lift, the lead to be measured from the centre of gravity of excavation to centre of gravity of spoil heap: the lift to be measured from natural ground level and paid for in layers of 1.5m each, including incidental work, as per specifications-in All kinds of soils | — | — | — | 4,408 | |
| — | 50.00 | — | — | ||
| Extra over item 011010 for excavation in foundations for buildings and bridges to cover dressing to neat dimension and plumbing sides etc. Note : Dressing under this item is payable for the total quantity of excavation in foundation and not partly | — | — | — | 460 | |
| — | 16.00 | — | — | ||
| Supplying and filling sand in plinth and under floors including watering, ramming, consolidating and dressing complete | — | — | — | 9,798.24 | |
| — | 385.00 | — | — | ||
| Filling, watering and ramming earth in 15 cm layers in floors and foundations with surplus earth from foundations including 50m lead and 1.5m lift | — | — | — | 7,546 | |
| — | 432.00 | — | — | ||
| Dressing Surface (average excavation or filling upto 15 cm) including removing vegetation in all kind of soil. Payment against this item is to be made only if it is not included in earth work item | — | — | — | 2,566.08 | |
| — | 100.00 | — | — | ||
| Loading/Unloading ballast, kankar, brickbats, stone-chips, shingle, stone boulders, block kankar, pitching stones , rubble stones, laterite, coal, surkhi, dry mortar, sand , moorum, earth, manure or sludge, ashes, lime etc., including lead up to 50m and stacking into/from trucks, trailors or wagons | — | — | — | 4,123 | |
| — | 100.00 | — | — | ||
| Leading ballast, kankar, brickbats, stone-chips, shingle, stone boulders, block kankar, pitching stones, rubble stones, laterite, coal, surkhi, dry mortar, sand, moorum, earth, manure or sludge, ashes, lime, debris, muck, malba, etc. for lead upto 25 km. Note : Lead under this item is payable when the same exceeds 500m. | — | — | — | 7,815 | |
| — | 75.00 | — | — | ||
| Providing and laying in position cement concrete of specified proportion excluding cost of cement, centering and shuttering - All works upto Plinth level : 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) | — | — | — | 1,18,367.25 | |
| — | 100.00 | — | — | ||
| Providing and laying cement concrete 1:2:4 in damp-proof course (1 cement : 2 sand : 4 graded stone aggregate 12.5mm nominal size - excluding the cost of cement and including providing, fixing and removal of forms. 50mm thick (20 mm coarse aggregate instead of 12.5mm) | — | — | — | 14,945 | |
| — | 135.00 | — | — | ||
| Providing and laying in position cement concrete of M 20 grade, excluding the cost of cement and of centering and shuttering, as per direction of the Engineer in charge : All works upto Plinth level | — | — | — | 2,33,658 | |
| — | 1496.00 | — | — | ||
| Extra for providing and mixing water proofing material of brand approved by railway, if not included in relevant item. | — | — | — | 1,81,345.12 | |
| — | 100.00 | — | — | ||
| Providing and laying in position M 20 Grade concrete for reinforced concrete structural elements but excluding cost of centering, shuttering, reinforcement and Admixtures in recommended proportion (as per IS:9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge All work upto plinth level, including raft foundation of washable aprons, HS tank, pile cap, footings of FOB, and Platform shelter etc. | — | — | — | 1,97,471 | |
| — | 110.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, raft foundation of washable aprons, Pile caps, Footings of FOB etc. | — | — | — | 13,277 | |
| — | 600.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Columns, pillars, , posts and struts | — | — | — | 1,54,080 | |
| — | 1200.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, bed blocks, girders, bressumers and cantilevers | — | — | — | 2,23,560 | |
| — | 225.00 | — | — | ||
| Providing and laying in position M 20 Grade concrete for reinforced concrete structural elements but excluding cost of centering, shuttering, reinforcement and Admixtures in recommended proportion (as per IS:9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge All work in buildings above plinth level upto floor two level. | — | — | — | 4,91,708.25 | |
| — | 150.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for special shapes Weather shade, Chajjas, corbels etc. including edges | — | — | — | 46,782 | |
| — | 150.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached plasters, buttresses, plinth and string courses etc. | — | — | — | 30,975 | |
| — | 775.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies, FOB slabs, walkway slabs and access platform | — | — | — | 1,64,005.5 | |
| — | 20.00 | — | — | ||
| Centering and shuttering including strutting, propping etc. and removal of form for : Stairs (excluding landings) except spiral-staircases | — | — | — | 4,588 | |
| — | 5.00 | — | — | ||
| Providing, hoisting and fixing in position upto floor two level M20 Grade precast RCC work including setting in cement mortar 1:3 (1 cement : 3 coarse sand) and finishing smooth with 6mm thick cement plaster 1:3 (1 cement : 3 fine sand) on exposed surfaces complete including cost of centering, shuttering, finishing, Admixtures in recommended proportion (as per IS:9103) to accelerate, retard setting of concrete, improve workability without impairing strength and durability, excluding cost of cement and steel reinforcement, as per approved plan & direction of Engineer incharge. In slabs for drain covers, manhole covers, flue tops etc. | — | — | — | 12,429.4 | |
| — | 60.00 | — | — | ||
| Brick work with modular bricks of class designation 7.5 in foundation and plinth in : Cement Mortar 1:6 (1cement : 6 coarse sand) | — | — | — | 1,28,890.8 | |
| — | 425.00 | — | — | ||
| Brickwork with clay fly ash FPS bricks of class designation 75 in superstructure above plinth level upto floor two level. In: Cement mortar 1:6 (1 cement: 6 coarse sand). | — | — | — | 9,91,044.75 | |
| — | 15.00 | — | — | ||
| Brick work with non-modular (FPS) bricks of class designation 7.5 in foundation and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand) | — | — | — | 31,159.8 | |
| — | 200.00 | — | — | ||
| Extra over item 051010 & 051020 for brick work in superstructure beyond plinth level upto floor two level : | — | — | — | 30,052 | |
| — | 60.00 | — | — | ||
| Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4mm in both directions with wire of dia 0.63mm With Deodar wood beading 50x20mm | — | — | — | 24,891.6 | |
| — | 30.00 | — | — | ||
| Providing and fixing float glass panes with putty and nails including removal of old broken panes wherever required Frosted glass panes 4mm thick (10kg /sqm) | — | — | — | 15,356.1 | |
| — | 1650.00 | — | — | ||
| Providing wood work in frames of doors, windows, clerestory windows and other frames and trusses, wrought, framed and fixed in position : Sal wood | — | — | — | 72,748.5 | |
| — | 84.00 | — | — | ||
| Providing and fixing Nickel chromium plated brass sliding doors bolts and screws etc. complete : 300x16mm | — | — | — | 24,742.2 | |
| — | 32.00 | — | — | ||
| Providing and fixing Nickel chromium plated brass handles with necessary screws etc. complete 125mm | — | — | — | 4,003.2 | |
| — | 32.00 | — | — | ||
| Providing and fixing chromium plated brass door latch with necessary screws etc. complete 250x16x5mm | — | — | — | 5,909.12 | |
| — | 64.00 | — | — | ||
| Providing and fixing bright finished brass hanging type floor door stopper with necessary screws etc. complete | — | — | — | 5,456.64 | |
| — | 105.00 | — | — | ||
| Supplying, providing and fixing white colour sliding uPVC Window complete, consisting of uPVC frame of size 80mm x 52mm and uPVC shutter of size 54mm x 38mm with 1.2mm thick GI section reinforcement wherever required, produced by ISO 9001:2000 and ISO 14001:2004 certified company. Window shutter will consist either of 5mm thick float glass or galvanised wire gauge alongwith complete fittings, e.g. pulley/rollers, transmission gear and handle for operating window | — | — | — | 6,45,043.35 | |
| — | 50.00 | — | — | ||
| Providing and fixing to IS: 2202 Part-1 marked flush door shutter decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35mm thick including ISI marked stainless steel butt hinges with necessary screws | — | — | — | 95,301 | |
| — | 24.00 | — | — | ||
| Extra for providing and fixing flush doors with teak veneering on one side in item No.072150 | — | — | — | 6,941.04 | |
| — | 24.00 | — | — | ||
| Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 100mm | — | — | — | 983.04 | |
| — | 50.00 | — | — | ||
| Supplying, providing and fixing white colour sliding uPVC Door complete, consisting of uPVC frame of size 95mm x 60mm and uPVC shutter of size 66mm x 42mm with 1.2mm thick GI section reinforcement wherever required, produced by ISO 9001:2000 and ISO 14001:2004 certified company. Door shutter will consist either of 5mm thick float glass or galvanised wire gauge or solid PVC panel alongwith complete fittings, e.g. pulley/rollers, transmission gear and handle for operating door | — | — | — | 3,26,261.5 | |
| — | 60.00 | — | — | ||
| Providing and fixing at all heights wall paneling of 9mm thick phenol bonded Bamboo Mat board conforming to IS : 13958-1994 including providing and fixing to framework made of 50mm X 50mm hardwood plugs including cutting brick work and fixing in cement mortar and making good the walls etc. and also providing and fixing wooden moulded corner beading of triangular shape to the junction of paneling etc. with iron screws as a complete job | — | — | — | 90,216.6 | |
| — | 400.00 | — | — | ||
| Providing and fixing specified wood frame work consisting of battens 50x25mm fixed with rawl plug and drilling necessary holes for rawl plugs etc. including priming coat complete Hollock wood or locally available comparable species of country wood (to be listed by respective railway). - kiln seasoned & chemically treated | — | — | — | 21,444 | |
| — | 80.00 | — | — | ||
| Providing and fixing 25mm thick cup board shutters , with prelaminated flat pressed 3 layer particle board conforming to IS 12823 -Grade I, having one side decorative lamination of approved shade and other side balancing lamination including second class teak wood lipping 25x12mm thick with necessary screws and nickel plated bright finished MS piano hinges complete | — | — | — | 1,84,682.4 | |
| — | 78.00 | — | — | ||
| Providing and fixing bright finished brass butt hinges with necessary screws etc. complete 100x85x5.5mm (heavy type) | — | — | — | 14,410.5 | |
| — | 32.00 | — | — | ||
| Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete 200x10mm | — | — | — | 5,973.12 | |
| — | 32.00 | — | — | ||
| Providing and fixing bright finished brass handles - with screws etc. complete - of size 125 mm | — | — | — | 4,887.68 | |
| — | 32.00 | — | — | ||
| Providing and fixing bright finished brass door latch with necessary screws etc. complete 250x16x5mm | — | — | — | 5,615.04 | |
| — | 120.00 | — | — | ||
| Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade I, Type II conforming to IS: 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass/ stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge Prelaminated particle board with decorative lamination on both sides | — | — | — | 1,13,786.4 | |
| — | 3000.00 | — | — | ||
| Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladders, railings, brackets, gates and similar works | — | — | — | 2,42,700 | |
| — | 200.00 | — | — | ||
| Fabricating, supplying & installing stainless steel railings for staircases, balconies, FOBs, Enquiry/Reservation complex etc., made of SS 304 grade stainless steel, laser cut / water jet cut (no shearing), polished with Automatic round/flat polishing machine to get a uniform hairline finish. All parts shall be connected to each other with the help of prescribed size CNC made solid connectors, countersunk screws. Welding should be finished ensuring that no welding marks are visible and assembly is mounted on floor with the help of dash fasteners. Railings shall be fabricated as per approved drawings by engineer-in-charge. Manufacturer shall submit maintenance manual and basic material test report for grade certification. | — | — | — | 1,36,890 | |
| — | 630.00 | — | — | ||
| Providing and fixing ceramic tiles conforming to IS:15622 of manufacturers approved by railway in all colours, shades, design and abrasion resistance class as approved by the Engineer- in-Charge in floors and landings over 20mm thick bed of cement mortar 1:4 (1cement: 3coarse sand) including pointing in white cement mixed with pigment of matching shade complete Of Group B-I-a of IS : 15622 (Vitrified tiles) of size above 400x400mm upto 600x600 mm | — | — | — | 5,85,969.3 | |
| — | 90.00 | — | — | ||
| Providing and fixing ceramic tiles conforming to IS:15622 of manufacturers approved by railway in all colours, shades, design and abrasion resistance class as approved by the Engineer- in-Charge in floors and landings over 20mm thick bed of cement mortar 1:4 (1cement: 3coarse sand) including pointing in white cement mixed with pigment of matching shade complete Of Group B-II Clause 5.1 (for abrasion resistance) of IS:15622 (Ceramic Floor Tiles) of size 300x300mm | — | — | — | 47,997 | |
| — | 190.00 | — | — | ||
| Providing and fixing ceramic tiles conforming to IS:15622 of manufacturers approved by railway in all colours, shades, design and abrasion resistance class as approved by the Engineer- in-Charge in floors and landings over 20mm thick bed of cement mortar 1:4 (1cement: 3coarse sand) including pointing in white cement mixed with pigment of matching shade complete Of Group B-I-b of IS : 15622 (Ceramic Tiles) of size 200x200mm to 400x400mm | — | — | — | 1,25,597.6 | |
| — | 250.00 | — | — | ||
| Providing and fixing Ist quality ceramic tiles conforming to Group B-III (Ceramic Wall Tiles) of IS:15622 of manufacturers approved by railway in all colours, shades, and design as approved by the Engineer-in-Charge in skirting, risers of steps and dado over 12mm thick bed of cement mortar 1:3 (1cement: 3coarse sand) including pointing in white cement mixed with pigment of matching shade complete 300x450 mm and above | — | — | — | 1,80,830 | |
| — | 10.00 | — | — | ||
| Providing and fixing 18mm thick mirror polished, machine cut for kitchen platforms, vanity counters facias, dados and skirtings and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touchups, including rubbing, curing. etc. complete at all levels Granite Black. Area of slab over 0.5 Sqm but upto 1.0 Sqm | — | — | — | 24,906.1 | |
| — | 150.00 | — | — | ||
| Providing and fixing 18mm thick mirror polished, machine cut for floors and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touchups, including rubbing, curing etc. complete at all levels Granite Black. Area of slab over 0.5 Sqm but upto 1.0 Sqm | — | — | — | 3,47,161.5 | |
| — | 30.00 | — | — | ||
| Providing and fixing 18mm thick mirror polished, machine cut for floors and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1cement: 4coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touchups, including rubbing, curing etc. complete at all levels Granite Pink/Grey. Area of slab 0.10 Sqm to 0.2 Sqm | — | — | — | 54,739.2 | |
| — | 150.00 | — | — | ||
| Extra for providing edge moulding to 16mm to 20mm thick marble/granite stone counters, vanities etc including machine polishing to edge to give high gloss finish etc. complete as per design approved by the Engineer-in-Charge Granite work | — | — | — | 19,722 | |
| — | 265.00 | — | — | ||
| Providing & fixing Precast Chequered tiles conforming to IS:13801:1993, manufactured under mechanical vibration & hydraulic pressing machine in double layer; top layer of 10 to 12 mm thickness of Dolomite Powder, graded chips, fibre and UV stabilised iron oxide Lanexess colour and bottom layer of 1:3 CC mixed with galvanised steel fibre of approved quality, jointed with neat cement slurry mixed with pigment to match shade of tiles including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4 of sizes : 300mm x 300mm x 30mm thick | — | — | — | 1,57,810.15 | |
| — | 1075.00 | — | — | ||
| Providing and fixing at all height false ceiling of 12.5mm thick tapered edge gypsum board conforming to IS: 2095-Part I, including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised with zinc coating of grade 350 as per IS: 277 and consisting of angle cleats of size 25mm x 1.6mm with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with stener 12.5mm dia x 40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm dia x 230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, - the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the gypsum board with recommended filler, paper tapes, finisher and two coats of primer suitable for gypsum board as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting. | — | — | — | 6,71,187 | |
| — | 80.00 | — | — | ||
| Providing and fixing on wall face unplasticised - Rigid PVC single socketed rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. 110mm dia. | — | — | — | 16,442.4 | |
| — | 20.00 | — | — | ||
| Providing and fixing on wall face unplasticised - PVC moulded bend and shoe for unplasticised-Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion Bend 87.5o, 110mm dia bend | — | — | — | 3,535 | |
| — | 25.00 | — | — | ||
| Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised- Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. Coupler, 110mm | — | — | — | 4,174.5 | |
| — | 720.00 | — | — | ||
| Providing and applying water proofing treatment to RCC roof slab etc. by application of two coats of cement slurry mixed with water proofing compound (Acrylic based polymer, solid content 30% ±3, pH >7) in the ratio of 1:2 (1 part of water proofing compound : 2 parts of cement by weight), followed by two coats of single component moisture cured polyurethane based elastomeric water proofing coating conforming to ASTM C-836-89 having tensile strength 3.1 N/mm². Topping layer of 25 mm thick cement concrete 1:2:4 (to be paid separately) to be laid | — | — | — | 5,04,460.8 | |
| — | 60.00 | — | — | ||
| 12 mm cement plaster of mix - 1:6 (1cement: 6fine sand) | — | — | — | 3,619.2 | |
| — | 3200.00 | — | — | ||
| 15 mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement: 6 fine sand) | — | — | — | 2,21,984 | |
| — | 200.00 | — | — | ||
| 15mm cement plaster on rough side of single or half brick wall finished a floating coat of neat cement of mix - 1:4 (1cement: 4fine sand) | — | — | — | 16,300 | |
| — | 3200.00 | — | — | ||
| Providing and applying plaster of Paris putty of 2mm average thickness over plastered surface to prepare the surface even and smooth complete | — | — | — | 2,33,152 | |
| — | 480.00 | — | — | ||
| 12mm thick cement mortar bands in cement mortar 1:4 (1cement: 4fine sand) Raised Band plain | — | — | — | 811.2 | |
| — | 80.00 | — | — | ||
| 18mm thick cement mortar band incl. cement mortar 1:4 (1cement: 4fine sand) - Raised Band plain | — | — | — | 165.6 | |
| — | 1600.00 | — | — | ||
| Finishing walls with Acrylic Smooth exterior paint with Silicone additives of required shade on new work (Two or more coats applied @ 1.67ltr/10 sqm over and including one coat of water proofing cement paint applied @ 2.20 kg/10sqm | — | — | — | 1,31,056 | |
| — | 1600.00 | — | — | ||
| Finishing walls with Acrylic Smooth Interior paint of required shade on new work (Two or more coats applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm | — | — | — | 1,26,176 | |
| — | 60.00 | — | — | ||
| Painting two coats (excluding priming coat) with chocolate, red, grey or buff ready mixed paint of approved quality, on steel or wood work | — | — | — | 2,725.8 | |
| — | 60.00 | — | — | ||
| Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia. nominal bore | — | — | — | 8,629.2 | |
| — | 50.00 | — | — | ||
| Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia. nominal bore | — | — | — | 9,173 | |
| — | 160.00 | — | — | ||
| Providing and fixing medium grade G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the wall etc. Concealed pipe including painting with anti corrosive bitumestic paint, cutting chase and making good the wall 15 mm dia. nominal bore | — | — | — | 29,913.6 | |
| — | 400.00 | — | — | ||
| Providing and fixing medium grade G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work 50 mm dia. nominal bore | — | — | — | 1,59,104 | |
| — | 110.00 | — | — | ||
| Providing and fixing medium grade G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work 40 mm dia. nominal bore | — | — | — | 34,943.7 | |
| — | 120.00 | — | — | ||
| Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia. nominal bore | — | — | — | 28,935.6 | |
| — | 14.00 | — | — | ||
| Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm nominal bore | — | — | — | 5,553.1 | |
| — | 6000.00 | — | — | ||
| Providing and placing on terrace/staging (at all heights) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank | — | — | — | 44,160 | |
| — | 10.00 | — | — | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 50mm nominal bore | — | — | — | 3,176.8 | |
| — | 4.00 | — | — | ||
| Providing and fixing C.P. brass bib cock, 15mm nominal bore, of approved quality conforming to IS:8931 | — | — | — | 973.56 | |
| — | 6.00 | — | — | ||
| Providing and fixing C.P. brass stop cock, 15 mm nominal bore, (concealed) of standard design and of approved make conforming to IS:8931 | — | — | — | 2,110.92 | |
| — | 15.00 | — | — | ||
| Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work) 25mm nominal bore | — | — | — | 2,239.65 | |
| — | 80.00 | — | — | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing in This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the walls etc. 15mm nominal outer dia. Pipes | — | — | — | 12,310.4 | |
| — | 60.00 | — | — | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing in This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the walls etc. 20mm nominal outer dia. Pipes | — | — | — | 10,277.4 | |
| — | 80.00 | — | — | ||
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing in This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the walls etc. 25mm nominal outer dia. Pipes | — | — | — | 16,128 | |
| — | 56.00 | — | — | ||
| Providing and fixing wash basin with C.I./ M.S. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required white vitreous china flat back wash basin size 550x400mm with single 15mm C.P. brass pillar tap | — | — | — | 77,142.24 | |
| — | 300.00 | — | — | ||
| Providing and fixing 110mm dia PVC soil, waste and vent pipes including jointing and cost of spun yarn and sand etc. complete | — | — | — | 71,607 | |
| — | 200.00 | — | — | ||
| Providing and fixing 75 mm PVC soil, waste and vent pipes including jointing and cost of spun yarn and sand etc., complete | — | — | — | 27,648 | |
| — | 6.00 | — | — | ||
| Providing and fixing Towel rail (C.P.)brass15 mm dia x 600 mm long having approx. wt.500 gm | — | — | — | 2,346.48 | |
| — | 12.00 | — | — | ||
| Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe 32mm dia. | — | — | — | 817.44 | |
| — | 24.00 | — | — | ||
| P&F 127mm dia C.P. steel Jali cockroach trap (CCTR-127) for gully floor or Nahani trap | — | — | — | 5,312.88 | |
| — | 12.00 | — | — | ||
| Grading / Regrading of roof for water proofing treatment with : Cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 20mm nominal size) | — | — | — | 19,125.84 | |
| — | 95.00 | — | — | ||
| — | 1075.00 | — | — | ||
| — | — | — | 86,655.75 | ||
| — | 20.00 | — | — | ||
| — | — | — | 8,965.8 | ||
| — | 20.00 | — | — | ||
| — | — | — | 3,924 | ||
| — | 30.00 | — | — | ||
| — | — | — | 11,355 | ||
| — | 370.00 | — | — | ||
| — | — | — | 1,08,461.8 | ||
| — | 58.00 | — | — | ||
| — | — | — | 14,089.36 | ||
| — | 275.00 | — | — | ||
| Supply and using cement at worksite : PPC | — | — | — | 15,49,625 | |
| — | 38500.00 | — | — | ||
| Supplying Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars | — | — | — | 20,20,480 | |
| — | — | — | Above/ 1898271.44 Below/P | ||
| — | 10.00 | — | — | ||
| Supplying and fixing under counter wash Basin 190x 550 x 430mm jaquar Make with contractors materials and labour and as per direction of Engineer-in-charge | — | — | — | 41,644.4 | |
| — | 14.00 | — | — | ||
| Supplying and fixing pillar cock with brass cap Jaquar or similar make with contractors materials and labours and as per direction of Engineer in charge. | — | — | — | 26,095.16 | |
| — | 14.00 | — | — | ||
| Supplying and fixing of bottle Trap 1 ¼" Complete set Jaquar Make with contractors materials and labours and as per direction of Engineer in charge. | — | — | — | 27,080.84 | |
| — | 14.00 | — | — | ||
| Supplying and fixing EWC wall Hung with CI bidet Bolt with brass cap Jaquar or similar make with contractors materials and labours and asper direction of Engineer in charge. | — | — | — | 2,79,062.42 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Annexure-AEngg.Org._.pdf
ATTACHMENT
Annexure-BPlantMachinery.pdf
ATTACHMENT
Annexure-CWorkinHand.pdf
ATTACHMENT
Annexure-EEFTdetail_R-1.pdf
ATTACHMENT
Annexure I
ATTACHMENT
Annexure-J.pdf
ATTACHMENT
AnnexureVIABidsecurityformat.pdf Annexure VIA
ATTACHMENT
Annexure-VIB.pdf
ATTACHMENT
Annexure-W.pdf
ATTACHMENT
CE16Revised2023-1-111.pdf
ATTACHMENT
PCECircular31-1-171.pdf
ATTACHMENT
SCC121-12-Revised.pdf
ATTACHMENT
GCC 2022 upto ACS11
ATTACHMENT
AnnexureI-Icommunicationdetails.pdf
ATTACHMENT
AnnexureVIABidsecurityformat.pdf
ATTACHMENT
GCC2022uptoACS11-compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .