SPECIAL REPAIRS TO BLDG NO BK-2 (OR LIVING) OF 1872 RKT REGT (SMERCH) AT NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering in cement mortar (1:4) 10mm thick as in ceiling surfaces finished fair and even complete all as specified & directed.

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finished fair & even complete all as specified and directed.

M& L for rendering in cement mortar (1:6), 15mm thick on stone masonary surfaces finished fair and even complete all as specified and directed.

Racking out joints/pointing to RR masonry or brought upto couse built in cement mortar all as specified.

M&L keyed pointing CM (1:4) to RR masonry uncoursed or brought upto course all as spd and directed.

M & L and preparation of new wall surfaces and applying two coats of oil bound distemper over two coats of white putty filling complete all as specified and directed

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

M & L preparation old decorated surfaces of walls and providing one coat of cement base paint complete all as specified and directed.

M & L preparation new decorated surfaces of walls and providing two coat of cement base paint complete all as specified and directed.

M & L for bitumen blown any grade, applied hot, two coats, to concrete surfaces at the rate of 1.5 Kg per sq m per coat and applying plythene film black, 50 micron laid in floors complete over sunken floor slab and embedded in side wall / covered fillet complete all as specified and directed. Note :- Supply of water proofing compound shall be measured and paid separately.

Supply only water proofing compound ISI Marked complete all as specified and directed.

M & L PCC (1:5:10) type E-2 using 40mm graded crushed stone aggregate as in sunken floors complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n. exc 15cm thickness(above or below ground level) complete all as specified and directed.

M&L for Non-skid ceramic coloured tiles 7 mm thick (jointless) (square/rectangular) area of each tile exceeding 0.11 sqm but n exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over screed bed or bedding layer 15 mm thick in CM (1:6) laid over complete all as specified & directed.

M&L for 300 x 450 x 6-7mm thick glazed ceramic tiles mat finished coloured jointless of pattern as approved by GE as in vertical surfaces such as skirting, dado and similar work over 10mm screed in CM 1:4 complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick over 15mm thick screed bed in CM 1:6 laid and and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab incl rubbing & polishing complete all as specified & directed.

M&L for 25mm thick PCC 1:2:4 type B-1 (using 20 mm thick crushed stone aggregate) as in sub base complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 sqm each leaf and removing from site all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50sqm each but not exc 4.00 Sqm and removing from site all as spd and directed and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50sqm each and removing from site all as spd and directed and making good disturbed surfaces of wall in CM (1:3) complete all as specified and directed.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F second class HW Hollock/Sal/Bansum (Terminalia Myriocapra), 35 mm thick, gauged and skeleton shutters, factory made open rebated (Three panels)and prepare to receive glass, gauge etc with out sash bar, edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 1991 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S & F Steel window factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wire gauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note :- Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F Steel ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wire gauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame including necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F MS butt hinge medium wt.cold rolled ISI marked of size 100mm complete all as spd and directed.

S&F 300mm aluminium alloy anodised sliding door bolts with hasp and staple (bolt type) & fixing clip of sheet cast or extruded section & fixing bolt & sliding bolts of extruded section or cast aluminium alloy all as spd & directed.

S&F for Aluminium anodised barrel tower bolt 150mm long of extruded section & fixed complete.

S&F 150mm long aluminium anodised handles extruded type complete all as spd & directed.

M & L for rolled mild steel work frame work as in doors or gates of angle or other section with gusset plates , rails, braces, etc complete drilled for fixing and confirming to Fe-290 or Fe-330 complete all as specified and directed.

Taking out old unserviceable steel wire cloth & S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

S&F sheet glass, ordinary quality 4 mm thick fixed with oil putty size of glass n .exc 0.50 sqm in each pane complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

Demolition of stone/brick masonry built in cement or cement lime mortar complete all as spd & directed

M&L for brick work with old size fly ash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in C M 1:4 all as specified & directed.

M&L for PCC 1:3:6 type C-1 using 20 mm aggregate as in coping, bed block etc complete all as spd & directed.

M & L for rendering on chajjas and projection in cement mortar (1:4) 10mm thick on concrete/brick masonry surfaces finished even and smooth w/o using extra cement complete all as specified

Taking down CI pipe 75 to 100mm in any type laid in trenches, floor or fixed wall etc including accessoriesl complete all as specified and directed.

S&F CI soil and wate pipe 100mm bore waste or vent pipe in any length with or without ears, with cement joints laid in floor or in trenches complete all as specified and directed.

Description all as per Ser item No 45.00 here in before but 75 mm bore.

S&F CI soil and waste pipe 75mm bore waste or vent pipe in any length with or without ears, with cement joints on vertical surfaces of wall complete all as specified and directed.

Fixing only 75 mm bore CI pipe as on wall .

S&F in CI branch pieces 100mm bore, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and directed.

S&F CI bends 100mm bore (any radius) diminishing pieces or tapers (large bore measured) as in repairs

Description all as per Ser item No 50.00 here in before but 75mm bore.

S&F CI Floor/Nahani trap 75 mm outlet, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) as in repairs.

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

Description all as per Ser item No 53.00 here in before but 20 mm bore.

Description all as per Ser item No 54.00 here in beforebut 25 mm bore.

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

Description all as per Ser item No 56.00 here in before but 20 mm bore.

Description all as per Ser item No 56.00 here in before but 25 mm bore.

M & L for fixing only 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc.

Description all as per Ser item No 59.00 here in before but 20 mm bore

Description all as per Ser item No 59.00 here in before but 25 mm bore

S&F PVC connection, heavy duty 15mm bore, 45cm long with 2 Nos PTMT nuts of approved quality complete all as specified and directed

Supply and fix in repair vitreous china bowl urinal flat back of size 465 x 355 x 265 mm white with grating and union for discharge pipe including waste pipe, fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs and 60 mm long brass screws pointing around urinal back in cement, excluding flushing cistern, flush pipe and waste pipe complete all as specified and directed

Taking out old unserviceable wash down closet and S & F vitreous china wash down water closet pan (pedestal pattern), coloured and seat cover white closed pattern with flat bottom and mild steel chromium plated hinge device including connections to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc complete all as specified and directed

S&F in repairs, wash hand basin vitreous china white / ivory colour flat size 550 x 400mm fixed including waste coupling, waste pipe complete all as specified and directed

S&F in repairs Chromium plated concealed stop cock 15 mm dia screwed down light pressure screwed both ends for iron pipe or for union complete all as spd & directed.

S&F in repairs pilllar taps fancy type cast copper allloy capston headed, chromium plated, screwed down, high pressure with long screwedshank and fly nut, screwed for 15mm bore iron pipe.

S & F in repair shower arm 15mm size, 195 mm long with bend of 45 degree with flange of PTMT any colour ( minimum wt 40gms) for fixing with 15mm pipe complete all as specified and directed.

S&F in repair brass chromium plated towel rail 600 mm long complete all as specified and directed .

S&F in repair brass chromium plated soap dish complete all as specified and directed

S&F in repair 15mm bore angular stop cock brass chromium plated , cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixedwith wall flange of complete all as specified and directed.

Taking out old unserviceable water closet (squatt pattern) and S & F Vitreous China, Squatting pan Orissa pattern size 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe ) with Vitreous China ‘P’ or ‘S’ trap, front or back inlet including connection to trap and to flushing pipe, anti syphonage pipe , including PCC (1:2:4) type B-1 for fixing of WC and making good the floor to match the existing complete all as specified and directed.

Taking down old unserviceable flushing cistern and S&F PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity . White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

Taking down old unserviceable bib tap and S&F bib tap 15mm bore brass CP fancy type complete all as specified and directed

Demolition of concrete of any description and any position not otherwise specifacally existing unservicable treatment of any description including cement plaster/conctrete any thickness from roof surface cleaning of roof surfaces and and preparing it for further treatment and removing rubbish from the site up to 50 mtrs complete all as specified and directed.

M & L for 10mm thick (average) screed bed in cement mortar 1:3 in order to maintain proper slope and base over existing roof surfaces mixed with water proofing compound as per manufacturer’s instructions finished even and smooth without using extra cement complete all as specified and as directed. (Note: WPC will be paid separately)

M & L for five layered roof treatment with APP modified polymeric water proofing membrane, 2mm thick having centre core not less than 100 micron high molecular high density polythylene film (HMHDPE) protected on both sides with high polymeric asphaltic mix and 20 micron HMHDPE film weight not less than 3 Kg/ Sqm applied with bonding material using belown type bitumen conforming to IS-702 Grade 85/25 @ 1.20 Kg/ Sqm over bitumen primer conforming to IS- 3384 @ 0.40 Kg/ Sqm with final coat of bonding bitumen grade 85/25 @ 1.20 Kg/ Sqm over APP membrane with all overlaps complete all as specified and directed.

Material and labour for 40mm thick (average consolidated thickness) PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregate laid in slope as in padding, finished even and smooth on existing slope including provision of 'V' shaped groove 6mm wide and 10mm deep at 1.20 metre interval or parts thereof, both ways on top of PCC padding and filled with mastic bitumen of (1:1) proportion complete all as specified and directed.

M&L for coved fillet in PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate at junction of roof & parapet wall and other vertical surfaces and surface painted with a hot paving bitumen grade 30/40 conforming to IS-73 @0.70 Kg/Sqm over a coat of bituminous primer conforming to IS-3384 @ 0.30 Ltr Sqm complete all as specified and directed.

Dismantling of existing unserviceable water tank of any description capacity exc 500 Ltr but n. exc 1000 Ltrs capacity each and S&F rotational moulded synthetic (HDPE) water storage tank 1000 Ltr capacity hoisted & fixed in positioin , Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe 20mm, including two nipple and fixed all as specified in SSR Part-I complete all as spd & directed.

S&F decorative type knobs with bracket of MS/hard wood, polished/ powder coated fixing at end of pelmet rod complete all as specified and directed.

S&F in repair aluminium curtain rods powder coated( minimum thickness of powder coating 50 micron ) fixed to bracket complete all as specified and directed

M&L for preparation of old plastered surfaces of wall with complete removal of existing treatment and applying two coats of Ist quality oil bond distemper complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting existing of freme made ouut of MS tubes top and bottom rail. MS freme shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F solid PVC door frame of size 50mmx 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS Squar tube, fixing in opening as per specification & drawing complete all as specified and directed.

S & F Aluminium alloy anodised butt hinges, medium weight, cold rolled, ISI marked of size 100mm complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, stranded copper conductor single core FRLS cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick including 1.5 Sqmm stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth for:-

(a) One light point controlled by one, one way switch.

(b) One ceiling fan/exhaust point controlled by one, one way switch.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One 3 pin 5 Amp socket on independent board.

Description all as per item No. 91.04 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F switch piano flush type 5 amps, single pole one way 240 volts.

S&F switch piano flush type 15 amps, single pole one way 240 volts.

S&F Socket outlet 3 Pin 5/6 Amp flush type.

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type.

S&F ceiling fan regulator electronic flush type , steped (four step) 230 Volts AC.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

S&F of lamp holder PVC/polycarbonate type with back plate.

S&F LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make: Bajaj Cat Part No BLRB 18W CW for tube , BLRB - DB 118 for batten , Havells Cat part No LHLDDBXEUL7Z018 (for tube) LHFYBWP1TB1W020 (for batten) / Jaquar Cat Part no. LTBL01x018C ( for tube) LINDPATI 118X ( for batten) / Syska Cat part No SSK -T8-18W (tube) SSK-TL-22 F (batten)

S&F LED mirror light fitting 10 Watt sleek polycarbonate channel with white acrylic cover complete with all accessories pre-wired and including connecting flexible copper conductor cable with suitable size. Make : Bajaj Cat Part No. BCLSB 10 WH or equivalent model of Havells / Syska / Philips

S&F LED bulk head luminaire 10 W complete with all accessories and including connecting up with three core copper conductor cable complete all as specified and directed. Make :Havells Model - Endura Rugby Neo or equivalent model of Syska / Bajaj / Philips

S&F recess mounted LED light fitting 36 watt 2'x2' complete with LED driver. Make : Havells or equivalent model of Syska / Philips / Bajaj

Supply and fixing and testing energy saving street light luminaire 15 watt LED , pressure die cast housing , polycarbonate diffuser, IP 65 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed. Make : Bajaj Cat Part No. BCLST 15w LED or equivalent model of Syska / Havells / Philips

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning incl conecting up with three core flexible cable from ceiling rose to fan.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 4 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 4 sqmm multi stranded copper conductor cable.

S&F of MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing complete all as specified and directed. Make: Legrand / Schneider / Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's complete all as specified and directed. Make: Legrand / Schneider / Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F of MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed. Make: Legrand / Schneider / Seimens

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make: Legrand / Schneider / Seimens

S & F of MCB SPN, 240 volt, 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make: Legrand / Schneider / Seimens

S&F in repair sheet metal enclosures 240 volt with 02 pin and earth plug socket with top and one MCB SP 25 amp, 10KA, 'C' curve.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 incl dismantling of old unsv existing earthing .

Supply and laying XLPE insulated heavy duty armoured electric cable with stranded aluminium conductor 1100 Volt grade ,cross sectional area 25 Sq mm 4 core complete all as specified and directed.

Excavation in trenches in any type of soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth and getting out complete all as specified and directed.

M&L for filling clean and dry sand cushioning for cable in trenches all as specified and directed.

Returning, filling in , including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified and directed

Removal of surplus soil as obtained from excavation to a distance not exc. 50 Mtr and depositing where directed at a level not exc. 1.5 Mtr above the starting point all as specified and directed.

Supply and laying of bricks old class ‘B’ as protect on to UG cable laid flat adjoining to each other width wise all as specified.

Supply and fixing tubes light grade GI 40 mm dia with all fitting for cable protection.

K B Enterprises

M/S JAGDISH PRASAD AIRUN

M/s SUNIL ENTERPRISES

PD GUPTA AND COMPANY

M/s Kishan Gopal Agarwal

M/s Jai Jinendra Constructions