SPECIAL REPAIRS TO LT SWITCH GEAR AND MISC E/M WORKS, REPAIRS/ REPLACEMENT OF UNSERVICEABLE WATER PIPE LINE AND MISC REPAIR TO WATER INSTALLATION AT VARIOUS LOCATIONS OF MCEME AND REPAIR/ REPLACEMENT OF BER ENERGY METERS AND PROVN OF POSTPAID ONLINE

Amount

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size(proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size(proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size(proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required), incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size (proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size (proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size (proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical panel board of suitable size (proper working space shall be provided in each compartment), 3 Phase 4 wire system Outdoor type 3.15mm ,double door front and back openeing type sloped canopy(Hood) on top extended 100mm all-around, separate compartment for each control gear, cable alley, provision of knock out type plates for various sizes of cable up to 400 Sqmm 3.5 Core in and out( panel board shall have sufficent space to accommodate spare cables also if required) , incoming and outgoing feeders duly marked on revited plates etc, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls and monitors, PVC sleeved aluminium strip for connecting MCCBs, Panel mounted on angle iron frame of 50x50x6mm thick duly painted and embeded in PCC 1:3:6 type C1, 15cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanized iron earth strip 32 x 6mm dia, by means of nuts, bolts, check nuts and washer etc of galvanized iron and earth lead protected by provision of GI pipe medium grade 40mm bore from earth electrode to test point incl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM sheet (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25 x 6mm with lugs 2 Nos and with 8mm dia MS bar handle made to shape, GI pipe medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, complete all as specified in electrical plate No 3 of SSR Part I and connection to earth test point including testing on completion all as directed. Note :- Item of earthing includes cost of 7.5m long galvanized iron earth strip of 32 x 6mm size and protection pipe of 40mm bore GI medium grade.

M&L Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as requied 32x6mm galvanised iron strip including taking old un serviceable one.

Supply,test,laying & commissioning of XLPE insulated, armoured (heavy duty) electric cable with aluminium stranded conductor, 1100 volts grade, laid in trenches / duct/ fixed to wall with suitable size clamps / passing through pipe/Tunnel/under ground/surface up to the termination point(as directed by Engr-in-Charge) with necessary end terminations with suitable size cable lugs, cable glands, fixing of lugs with crimping with tool,nuts,boltsetc of the following sizes and including taking out unserviceable burnt out cable from its existing location complete all as specified and directed by Engr-in-Charge :-

3.5 Core X 240 Sqmm

3.5 Core X 400 Sqmm

Supply,test,install & commsissioning of Bus bar chambers(including 4 bus bars i.e R,Y,B and neutral),3-Ph with netral,1100volts,50Hz including suitable sheet metal enclosure along with necessary screws,nuts,bolts and other Misc accessroies and making connections(input &out put) with cable terminal ends complete for the following current carrying capacities,Panel mounted on suitable size & thickness of angle iron frame(proper mounting shall be done) duly painted and embeded in necessary required quatnity of PCC 1:3:6 type C1, 15cm below ground level and 30cm above ground level including taking down old unserviceable and consisting the following provisions:- Note : Size of Bus bar chamber should not be less than 0.70 x 0.75 x 0.35 m.

4-Way, 200 Amps

4-Way,250Amps

4-Way,400Amps

8-Way,400Amps

Supply and laying GI tubing medium grade with fittings such as Tees,beand,union,elbow, nipple,collor,sockets, reducer,clamps etc,fixed any height of wall,surface, celing,laid in trenches,under ground etc and including taking down old unserviceable pipe line from its existing location all as specified and directed for the following sizes

100 mm dia

80 mm dia

50 mm dia

40mm dia

25 mm dia

20mm dia

15mm dia

Supply and fix 50 mm CI, NRV screwed both ends for GI pipe and fixed etc including taking down old unservceable one all as directed complete all as directed by Engr-in-charge.

Supply and fix 65 mm CI, NRV screwed both ends for GI pipe and fixed etc including taking down old unservceable one all as directed complete all as directed by Engr-in-charge.

S&F gun metal gate valves ISI marked with iron wheel head and both ends screwed with both ends for GI pipe and fixed and complete all as directed by Engineer-in-Charge.

20mm dia

25 mm dia

40mm dia

50 mm dia

80 mm dia

100 mm dia

15mm dia

Taking out submersible pumpset of any capacity and type from the borewell of depth not exc 550 feets for carrying out repairs including cleaning and applying one coats of anti corrosive paint and lowering the same in position and commissioning after carrying out the flushing of bore well as required complete all as directed by Engineer-in-Charge.

M&L for flushing of the existing borewells of size 150/200/250 mm dia upto 550 feet depth by drilling machine by mechanically method into the above well connected to a pneumatic compressor after taking out the submersible pumpset with necessary hoisting equipment and flushing the bore well complete with compressor air and flushing bore well till discharge of fresh water is obtained subject to the entire satisfaction of Engr-in-charge and lowering down the submersible pump set in position complete all as directed by Engineer-in-charge.

Taking out unserviceable GI socket from 50 mm column pipe and S&F new GI socket 50mm (ISI marked) long type, heavy duty suitable for the column pipe complete all as directed by Engineer-in-Charge.

Cutting the existing damaged threading of GI column pipe 50 mm dia and re-threading on lathe machine complete all as directed by Engineer-in-Charge.

Removing old unserviceable column pipe as obtained from lowering of submersible pump set and S&F new GI column pipe 50mm dia, heavy duty, ISI marked, 3 metre length each, both ends machine threaded with long threaded socket complete all as directed by Engr-in-Charge.

Removing unserviceable PVC water proof cable of any size as obtained from lowering of submersible pump set and S&F new PVC water proof copper cable of size 3 core 2.5 sqmm suitable for submersible pump set complete all as directed by Engr-in-Charge. Make:- FINOLEX/FINECAB/PAYAL/POLYCAB

M&L for cable joint for water proof cable of 3 core 2.5 sqmm flat copper cable including testing and commissioning complete all as directed by Engineer-in-Charge.

Removing unserviceable PVC water proof cable of any size as obtained from lowering of submersible pump set and S&F new PVC water proof copper cable of size 3 core 4.0 sqmm suitable for submersible pump set complete all as directed by Engr-in-Charge. Make:- FINOLEX/FINECAB/PAYAL/POLYCAB

M&L for cable joint for water proof cable of 3 core 4.0 sqmm flat copper cable including testing and commissioning complete all as directed by Engineer-in-Charge.

Design, fabrication, supply and errecting connecting and testing totally enclosed out door type 3.15mm thick, LT Cubical DOL starter panel board of size not less than 50cmx50xcmx30cm, 3 Phase 4 wire system ,double door front and back openeing type sloped canopy(Hood) on top extended , cable alley, provision of knock out type plates for various sizes of cable up to 25Sqmm Sqmm 4 Core in and out, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls , Panel mounted on suitable size of angle iron frame thick duly painted & it shall be fixed from 15cm of ground level and embeded in PCC 1:3:6 type C1, 20cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

Design, fabrication, supply and errecting connecting and testing totally enclosed LT Cubical DOL starter panel board of size not less than 50cmx50xcmx30cm, 3 Phase 4 wire system indoor type 2mm ,double door front and back openeing type sloped canopy(Hood) on top extended , cable alley, provision of knock out type plates for various sizes of cable up to 25Sqmm Sqmm 4 Core in and out, CPRI approved factory made fabricated out of 3.15mm thick CRCA sheet duly treated through 7 tank pre treatment process and painted with epoxy power coated mat finish of SIEMENTS GREY structral RAL 7032 shade colour, built in industrial type locking arrangement on front and back and pre wired with PVC insulated multi stranded copper conductor for controls , Panel mounted on suitable size of angle iron frame thick duly painted & it shall be fixed from 15cm of ground level and embeded in PCC 1:3:6 type C1, 20cm below ground level and 45cm above ground level including taking down old unserviceable panel board and consisting the following provisions:-

S&F heavy duty HDPE coloumn pipe 50mm inner dia 16kg/Sqcm for borewell complete all as directed. Note: (i) Necessary T&P shall be provided at site by contractor. (ii) Rate Quoted shall be deemed to inclusive in unit cost.

Excavation in trenches not exeeading 1.5m wide and not exceeding 1.5m depth and getting out hard and dense soil for laying of under ground cable all as specified and directed by Engineer-in-Charge.

Returning and filling in soils including spreading, leveling, watering and well ramming in layars each not exceeding 25 cm thick all specified and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directred by Engineeer-in-Charge.

Supply,Fixing,testing and commissioning of AC Single Phase,Two Wire, Tamper Proof, Static Meter of Class 1.0, 240 V, 50 Hz,10Amps-60Amps Capacity, conforming to IS-13779 , relevant IEC standards and Latest BIS standards with inbuilt Low Power Radio Frequency (LPRF) communication facility in mesh network with default and on demand display, billing data generation facility, anti-tamper features, Microprocessor and LED/LCD based circuitry.The energy meter should be fixed inside transparanet box hinge type of suitable size including disconnecting of existing energy meter, fixing of wiring to new energy meter incoming and out going terminal ends from the DB/existing submain wiring along with necessary accessories,making good of disturbed surfaces complete all as directed by Engr-in-Charge.

Note :-(i) The rate quoted include cost of energy meter, cover box and all necessary E/M works,Civil works and Tools and plants. (ii) All Energy meter execution & commissioning to be done by Original Equipment manfracturer (OEM) authorised techinican, rate deemed to be included in quoted rate. (iii) Warranty certfifcate for minimum one year shall be submitted by contractor/OEM & calibration test certificate shall be submitted by OEM, quoted rate shall be deemed to be included in the unit cost. (iv)The contractor should provide sealing to energy meter, sealing materials, necessary tools for sealing and also the following details to be submiited by the contractor like Qtr no, New meter fixed no, intial Reading,date of installation including meter card shall be given to AGE E/M-II(U) office and respective individual occupant, rate deemed to be included in quoted rate (v) Old UNSV Electric Meters shall be handed over to AGE E/M-II store Yard. Make for Meter: L&T/Schnieder/ABB/Siemens/HPL/Elmeasure.

M&L for sub main wiring complete with 2 runs of 6 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor and drawing through surface or concealed in and including supply and fixing of flexible pvc conduit of suitable size and connecting to incoming and outgoing terminal ends of energy meter with necessary lugs, including provision of 1 run of 6 Sqmm PVC insulated heavy duty and unsheathed cable with multistranded copper conductor for earth continuity conductor and connecting to earth dolly complete. (Cosidered qty to replace the damaged submain wiring where ever required). Note : 3 runs of cable and 1 run of conduit shall be measured as single RM.

Supply, Install, Testing and Commissioning IP 51 rated Data Concentrator Unit (DCU) compatible for remote Automatic Meter Reading (AMR) solution and capable of communicating with the static energy meter in the corresponding frequency band and with the data server through GPRS and shall have minimum data transfer rate of 9600 bps, internal memory to store data of 50 modules for 6 month period and shall be based on Cyantech Mesh network within 50 metre range complete all as specified and directed. Make:- L&T/ Capital/ Cyanconnode/HPL/Elmeasure.

Design, Supply, Install, Testing and Commissioning configuration of cloud hosted multi user web based Software with provision of following modules:- (a) Meter Data Management Module:- The meter data management module would be responsible for collecting the data from the concentrator and make the data available to the billing system. The system would support offline meter data entry. The meter data management system would capture and provide the following data:- (i) 30 minutes instantaneous data from all the meters for seven parameters i.e., Cumulative Energy, Cumulative Apparent Energy, Power, Current, Voltage, Power Factor and Frequency. (ii) The monthly and quarterly billing survey data for cumulative energy and maximum demand. (b) Billing Module:- The billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and make energy data / billing data available to administative and end users.

(c) Occupation and Vacation Module:- The system would support occupation / vacation based on the unit categories. The system would support automatic data capture on occupation and vacation events. (d) Customer Portal:- The system would include a customer portal for the resident /occupant to login and view their own energy / billing data. (e) Energy Accounting Module:- The system would include features of energy accounting. The system would be able to account for total energy block wise, facility wise and would also allow calculations of unaccounted energy in case total energy meter is also available. (f) Communication Module:- The system would provide communication of energy data and bills via print, email and sms methods. (g) Meter Master Data:- The system would support meter master data repository and also would support meter replacement process. (h) Excel Export:- The system would support export of metering and billing data in excel format. Make:- Innologix/ L&T/ Capital/HPL/.

Supply, Install, Testing and Commissioning of IP 51 rated Repeater unit with inbuilt Low Power Radio Frequency (LPRF) Communication Facility and capable of communicating within Cyantech Mesh network with inbuilt AC power supply complete all as specified and directed. Make:- L&T/ Capital / Cyanconnode / HPL/Elmeasure.

POWER CONSTRUCTION COMPANY