REPAIR/REPLACEMENT OF FLOORING, ROOF SHEETS, JOINERY, SANITARY FITTINGS PLASTERING AND MISC BUILDING OF ZONE C, D and E AND APS AT MIL STN SGNR

Amount

Demolition of cement concrete (unreinforced) any description and in any position for sunken portion (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge:- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 D2 75 mm thick over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete all as specified and directed by Engineer-in-Charge. Note: (i) PCC filling in sunken portion will be measured seperately.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

M&L 450x300 x7/600x300x7 mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles and incliding 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L Non- skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles and laid over & incliding 15mm thick screed in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M & L Pre Polished kota stone slab flooring 20-25mm thick (minimum size 55 cms x 55 cms) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing laid over & including 15mm of screed bed in CM 1:6. complete all as specified and directed by Engineer-in-Charge.

M & L Pre Polished kota stone slabs as in vertical surfces such as risers of steps 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, mirror polishing also moulding edges laid over & including 10mm of backing coat in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

M & L granite (of any type) work 16 to 20 mm thick (table rubbed and polished) in cooking platforms and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over & including 15mm of screed bed in CM 1:6.complete all as specified and directed by Engineer-in-Charge.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over & including 15mm thick screed in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-Charge.

M & L for steel / Iron work as in doors or gates of angle or other section with gusset plates, rails, braces, iron sheets for cupboard etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (including of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290(Grade-165) complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed by Engineer-in-Charge.

M&L providing precast cement concrete 1:2:4 Type B1 as in cover slabs (for manholes etc) and similar articles with plain faces and set in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. (Note : The rate quoted shall be deemed to include use and waste of necessary form work)

M&L MS TMT bar 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for Providing precast RCC Jallies any shape ( cement concrete Type B0 1:2:4 12.5mm gragded aggregate) louvres and jallies, 40 mm thick (measured solid), including all mouldings set in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Demolition concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M&L75 mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L 25mm thick cement concrete flooring type B0, 1:2:4 using 12.5 mm graded aggregate finished even and fair complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling (25mm thick) under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L Machine pressed precast rubber moulded concrete coloured interlocking paver block any shape and size confirming to IS 15468-2006 of 60 mm thickness with grey cement and pigment M-35 Grade 20mm graded stone aggregate) complete all as specified and directed by Engineer-in-Charge.

M&L providing precast cement concrete in PCC (1:2:4) type B-1 with 20 mm graded aggregate for kerb stone and similar works with plain fair finishes including chamfers, weatherings, throat- ing etc. and setting in mortar (1:4) complete with joints to match complete all as specified and directed by Engineer-in-Charge.

M & L for 75mm thick cement concrete type C-1, 1:3:6 using 20mm graged aggregate as in plinth protection finished even & smooth complete all as specified and directed by Engineer-in-Charge.

M & L for 40mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in flooring , finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick work built in cement mortar of any description complete all as specified and directed by Engineer-in-Charge.

M&L brickwork withsub class `B' Bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster any description including raking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L 15mm thick rendering in CM 1:6 to brick/ concrete wall surfaces finished even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L 15mm thick rendering in CM 1:4 to brick/ concrete wall surfaces finished even & smooth w/o using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L, 10mm thick rendering in CM 1:3 on fair faces of concrete surfaces as on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L two coats of oil emulsion distemper over one coat of 1.50 mm thick wall putty on newly plastered wall (thickness 1.5mm) surfaces including preparation of surface complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surface of wall any description and applying two coats of oil emulsion distemper over & including 1.50 mm thick wall putty over a coat of chalk whiting layer on platered surfaces preparatory to distempering complete all as specified and directed by Engineer-in-Charge.

M&L three coats of white wash to new surfaces on ceilings including preparation of surface complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of existing treatment and applying two coat of cement base paint to old surfaces of walls over & including 1.50 mm thick wall putty including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for Complete removal of existing treatment and applying two coats of oil distempering to old surfaces of wall over & including 1.50mm thick wall putty including preparation of surface complete all as specified and directed by Engineer-in-Charge.

M&L two coats of white wash to old surfaces on ceilings including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down steel window / ventilators ( not exc 1.5 Sqm each) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm but n exc 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm but n exc 2 sqm each and refixing in same opening complete all as specified and directed by Engineer-in-Charge.

M&L factory made pressed steel frame for doors size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified. (Note : Thickness of MS Sheet shall be 1.25mm)

M&L factory made pressed steel frame for doors size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by Engineer-in-Charge. (Note : Thickness of MS Sheet shall be 1.25mm)

M&L providing cement concrete (1:3:6) type C1 for filling in pressed steel frames and other similar items etc complete all as specified and directed by Engineer-in-Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of but of Frame size 65x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F Factory made Second class hard wood glazed and skeleton window shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc divided into squares with plain, chamfered or rounded mitred and rebated sash bars any number & fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, section 8 clause 8.24(a) complete all as specified and directed by Engineer-in-Charge.

S&F Factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiberglass from all sides. M S stay shall be provided at the bottom to steady the frame. complete all as specified and directed by Engineer - in - Charge

S&F Factory Made Solid PVC Moulded Door Shutter With Particle Board Co, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed by Engineer - in - Charge.

S&F Factory made fiber glass reinforced plastic (FRP) Door frames of three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness. The laminate door frame molded with fire retardant grade unsaturated polyster resin and chopped mat. door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. the frame shall be covered with fiberglass from all sides. M S stay shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer-in-Charge.

S&F Factory made 30mm thick fiber glass reinforced plastic (FRP paneled Door Shitter of required colour and approved brand and manufacture made with fire-retardant grade unsaturated polyster resin. Moulded to 3mm thick FRP laminate for forming places for fixing of fittings cast monolithically with 5mm thick FRP laminate for panels and conforming to IS 14856-2000 complete all as specified and directed by Engineer-in-Charge.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F aluminium handle cast type anodised, 150mm long complete all as specified and directed by Engineer-in-Charge.

S&F 300mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed by Engineer-in-Charge.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long complete all as specified.

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

S & F for floor door stopper of aluminium alloy body and tongue, Overall length of cover plate 140mm anodised, with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge.

S&F 4mm sheet glass ordinary quality and glazing with oil putty in square n. exc 0.5 sqm in each plane complete all as specified and directed by Engineer-in-Charge.

Supply & Fix 4mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in suqares exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick sorrounds, glazed with oil putty or fixed with beads. complete all as specified and directed by Engineer-in-Charge.

S&F factory made steel windows with side hung shutters including hinges with steel handle and steel peg stay, complete with glazing bars, devetailed or welded including taking down from site complete all as specified and directed by Engineer in Charge

S&F factory made steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley, wheel including taking down from site complete all as specified and directed by Engineer in Charge

M&L anodised aluminium frames for doors, windows with one or moe rebates including jointing cleats for fixing etc.including power coating minimum thickness of power coating shall be 50 micron as per the specification) complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,powder coated aluminum snap beading screws etc. complete all as specified.complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium windows and ventilator shutters, side hung type, without sash bars aluminium saction weighing 0.55 kg/RM including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as peg stay 150mm long (1 no) hinges type B21 100 mm long (2 No) suitable handle (1No) including aluminium grill and wire mesh complete all as specified and directed by Engineer-in-Charge.

S&F in repair Aluminum alloy wire cloth , 0.45 mm nominal dia of wire and average width of aperture and fixed with aluminium wire staples complete all as specified and directed by Engineer-in- charge.

S&F in repair Anodised aluminum grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15 ) of approved design /pattern, with approved standard section and fixed to the window /door with C.P brass/SS screw @ 200mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles. Note:- Design shall be approved by Engineer - in - Charge. Note :- Minimum thickness of powder coating shall not be less than 50 micron.

M&L two coat of synthetic enamel paint on old painted surfaces of wood and wood based materials over 10 cm width or girth including preparation complete all as specified and directed by Engineer-in-Charge.

M&L two coats of synthetic enamel paint over a coat of pink primer on new surfaces of wooden and wood based materials over 10 cm width or girth including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L two coats of synthetic enamel paint on old painted surfaces of steel and iron work over 10 cm width or girth including preparation complete all as specified and directed by Engineer-in-Charge.

M&L, two coats of synthetic enamel paint over a coat of red oxide on steel surface over 10 cm width or girth, not otherwise described including preparation of new surface. complete all as specified and directed by Engineer-in-Charge.

M&L, two coats of Plastic emulsion paint over a coat of primer on new Surfaces of any description over 10cm girth or width, not otherwise described described including preparation of new surface complete all as specified and directed by Engineer-in-Charge.

M&L, two coats of Plastic emulsion paint over a coat of primer on old Surfaces of any description over 10cm girth or width, not otherwise described described including preparation of new surface.complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs counter top/ counter sunk vitreous china wash hand basin white flat back of size 550mm X 400mm, fixed with a set of cast iron brackets including cutting and pinning in ends of brackets to wall, provision of 15mm size pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter "Hot or cold'' with long scrwed shanks and fly nuts, 32mm dia brass chromium plated waste fittings 450mm long PVC connection of 15mm size with PTMT nuts and 40mm dia waste pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous China wash down water closet pan (pedestal pattern), white complete, including white seat cover with hinging arrangement, (excluding fixing bolts, flushing cistern and flush pipe complete all as specified and directed by Engineer-in-Charge.

Supply & Fix in repairs white vitreous china squatting pan orissa pattern of size 580mm x 440 mm, with integral foot rest and P or S trap connection to trap and to flushing pipe front or back inlet including, trap and taking out old WC & connections etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair, 10 ltr capacity low level PVC valveless, syphonic action type flushing cistern(dual system), white, with inlet, ball valve, flush pipe, PVC connection 15 mm dia and 450 mm long float and handle including bracket complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP toilet paper holder complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP soap dish, complete all as specified and directed by Engineer-in-Charge.

Supply and fix CP stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends Bore of pipe in 20mm, fixed in repairs. complete all as specified and directed by Engineer-in-Charge.

Supply and fix CP stop valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends Bore of pipe in 25mm, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply and fix in CP repairs stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by Engineer-in-Charge.

Supply and fixed pillar tap 15mm dia cast copper alloy with capstan heads, chromium plated screwed down high pressure with long screwed for iron pipe of 15 mm dia, fixed in repairs.complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs CP Angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with crutch or butter fly handle for iron pipe or for union and complete all as specified and directed by Engineer-in-Charge.

S&F in repairs CP15mm bore bib taps cast copper alloy, chromium plated fency type with crutch or butterfly handle screwed down screwed for Iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer-in-Charge. .

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed by Engineer-in-Charge.

S&F PVC gratings 100 mm dia of PTMT fixed in repairs.(Minimum weight 25 gms ) complete all as specified and directed by Engineer-in-Charge.

S&F CP brass shower rose 125mm size and 15mm dia, fixed inrepairs complete all as specified and directed by Engineer-in-Charge. .

S&F in repair 32mm dia PVC down take waste pipe for WHB of 75cm long complete all as specified and directed by Engineer-in-Charge.

S&F in repair CP towel rail 600mm long fixed with CP brass screws complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI steel water tubing 15mm bore and connections including fittings from floor/walls/ceiling complete all as specified and directed by Engineer-in-Charge.

Taking up or down GI Steel water tubing 20mm bore and connections including fittings from floor/walls/centrings complete all as specified and directed by Engineer-in-Charge.

S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good complete all as specified and directed by Engineer-in-Charge.

Fixing only tubes, of 15mm bore any grade,(medium) to walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

S & F GI steel water tubing 20mm bore medium grade with all fittings and fixed complete to walls ceiling or laid in floorscomplete all as specified and directed by Engineer-in-Charge.

Fixing only tubes, of 20 mm bore any grade,(medium) to walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

Taking down or up steel water tubing 25 mm dia bore of pipe and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge.

Refixing old steel tubing and connections in new or old position (walls, ceiling, flooring etc).Bore of pipe in 25 mm. complete all as specified and directed by Engineer-in-Charge.

Supply and fix tubes medium grade steel tubing 25mm dia laid to walls floors etc complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks any type exc. 250 ltr but nexc 500 ltr complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks any type exc. 500 ltr but nexc 1000 ltr complete all as specified and directed by Engineer-in-Charge.

S & F rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I (500 Ltrs) capacity. complete all as specified and directed by Engineer-in-Charge. Note : PVC tank shall be ISI mark & having two layer)

S & F rotational moulded polythylene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part -I (1000 Ltrs) capacity complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 250 ltr but not exc 500 ltr and from mouths of circulating pipes, complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 500 ltr but not exc 1000 ltr and from mouths of circulating pipes, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repairs ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed for bore dia of pipe 20mm complete all as specified and directed by Engineer-in-Charge.

S & F in repair 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches, if required complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm dia cast iron sand cast waste and vent pipes in any length with or without ears with cement jointed fixed to wall complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm dia cast iron sand cast waste and vent pipes in any length with or without ears with cement jointed fixed to wall complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm dia cast iron Bends complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm dia cast iron Bendscomplete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes,PVC (SWR) pipes ( any size or pattern ) including all fittings heads ,shoes, bends, and removal to store complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls including necessary scaffolding upto the height of building from ground level complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) bend with oval access door.complete all as specified and directed by Engineer-in-Charge.

S&F in Repair drapery curtain rod, mild steel, chromium plated 25mm dia fency type with fixing of decoreted type brackets,stops, rollers including end knobs etc complete all as specified and directed by Engineer-in-Charge.

Fixing of old locker including fixing of nut bolts 4 Nos of any size in each locker including welding of hinges, handles , locking arrangement and painting all complete as directed by Engineer in charge) and including welding work in steel inbuilt lockers for broken hinges,handles,inluding two coat painting with synthetic emulsion paint complete all as specified by the Engr-in-Charge.

S&F in repairs for door closer hydraulically regulated, alunimiun body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete.

S & F in repair 15mm dia brass CP mixer (Wall/Basin) for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.Prayag cat No-8550,parryware Cat No-G4636A1,CERA Cat No-F1005501.

S&F sinks with drainage board made of stainless steel 1 mm thick for kitchen with plugs, washers and waste coupling 40mm bore dia of discharge pipe , waste pipe plain 90cm long suitable for sink waste coupling, waste jali including making grooves , fixing properly or bedding in cement mortar to walll or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer - in - Charge.

Dismantling steel sheets (corrugated semicorrugated ,Plain or corrugated steel sheeting,any gauge, thickness etc) sheet in roof covering complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 0.56 Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight and for covering of crumple joint etc complete all as specified and directed by Engineer-in-Charge.

Dismantling Wall and ceiling boards (fibre, pulp, ACinsulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets & snap grid and any description. complete all as specified and directed by Engineer-in-Charge.

S&F for Anodised aluminium snap grid frame work for false ceiling including hangers complete all as specified and directed by Engineer-in-Charge.

S&F Gypsum board false ceiling of size 600 x600 x12 cm thick for false ceiling panel or tiles for insulation and accoustic purposes, 60 cm x 60 cm in size laid/inserted to timber/GI/Aluminium framework with screws complete all as specified and directed by Engr-in-Charge.

S&F solid PVC wall Lining/fillet consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC as per specification and drawing all as specified and diected by Engr-in-Charge. (Note : PVC Strip shall not be paid separately.)

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and directed by Engineer-in-Charge.

M&L for Second class Clean sawn hard-wood Plain , solid , straight chowkhats and frames , wrought , framed rebated on the solid , rounded or chamfered , put together with glue, pinned at joints, supplied and fixed. in scantlings and for frame etc complete all as specified and directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sq. cm and over in section, in any position in framed work complete all as specified and directed by Engineer-in-Charge.

S&F in repair Prelaminated particle board,19 mm thick interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Continuous (piano) hinges, (width of flap 40mm when open) mild steel, bright finish or electrogalvanised complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium 150 mm long Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified and directed by Engineer-in-Charge.

S&F in repair for vitreous China urinals,full stall urinal (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) and including Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed by Engineer-in-Charge.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed by Engineer-in-Charge.

M&L 30 cm x 30 cm x 20-25 mm thick chequered cement concrete tiles set jointed and pointed in neat cement slurry in floors with grey cement and no pigments with laid over & including 20mm of screed bed in CM 1:4 including coping at edges in PCC Type B1 (1:2:4) complete all as specified and directed by Engineer in Charge

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Engineer-in-Charge.

S & F in repair for brass mortice lock, vertical type, size 100 mm and 4 lever type complete all as specified and directed by Engineer-in-Charge. .

S&F in repairs Seat and cover for pedestal pan complete all as specified and directed by Engineer-in-Charge.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long bu with aluminium alloy brackets and guard rail complete all as specified and directed by Engineer-in-Charge.

S&F Towel Ring of aluminium fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed by Engineer-in-Charge.

S&F Health faucet fixing in pipe etc. complete all as specified and directed by Engineer-in-Charge.

S&F Urinal partitions slabs terminating about 40cm above floor line, fixed in repairs complete all as specified and directed by Engineer-in-Charge.

S&F Glass shelf assembly fixed in repair complete all as specified and directed by Engineer-in-Charge.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

Taking down shutters door/window/cupboard of any description (Wooden/aluminium/ iron/Glass) of any material and any type exc 1 Sqm but n exc 2 sqm each and repairing work in all respects, (including neccessary cleats, rubber packing etc in aluminium Door) and refixing in same opening complete all as specified and directed by Engineer - in - Charge.

Supply and fixing in replacement Kitchen Rack / Dish Rack (Kitchen Stand or wall mounted) of size 750mmx600mmx250mm (Appx size) made out of Food Grade Stainless Steel 1mm thick sheet/strip including necessary arrangements for plates and utencils to keep (Holds up to many plates or bowls To accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories complete all as directed by Engineer-in-charge.

Supply and fixing in repairs metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed by Engineer-in-Charge.

M&L for painting lines, dashes, arrows letters etc on road pavement/path/kerb stone and the like exc 10 cm wide by using themoplastic paint with heating arrangement upto 160 degree celcious complete all as specified and directed by Engineer in Charge

M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed by Engineer-in-Charge.

Material & Labour in repairs for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge. Note: Holes for screws/rivets, and screws/rivets etc will not be paid separately

Note :(i) Amount of credit for retrieved materials is mentioned in Sch 'A' Section-II of tender documents in pdf form which will be deducted while acceptance of tender offline.

J and P CONTRACTOR

PAREEK AND COMPANY

SHIVA CONSTRUCTION COMPANY