Loading…
Loading…
Tender Value
₹14.0 Cr
EMD Value
₹28.1 L
Closing Date
27 May 2026, 3:00 pmClosed
Yes (up to 3 members)
No
Two Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
SR.DEN/CO
24 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees; N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. In this reference, fourth previous year shall be considered only if bidder(s) give their consent in Annexure VIB as "previous year is yet to be prepared/ audited". The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/Certificate from Chartered Accountant duly supported by Audited Balance Sheet. Criteria with explanation & Format are attached as a link.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip]
Similar nature of work for minimum eligibility criteria:-"Any type of civil work viz. building up to G+4 and structures work, pipe lines, underground and overhead tanks, foundation treatment works in any railway embankment/cutting, any earth work, cover over platform, bore wells, level crossing works including lifting barriers, cement concrete apron works."
(a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Tenderer shall carefully read clause No. 10 including clause no. 10.1 to 10.5 of IRGCC April 2022.
The total value of similar nature of work completed during the qualifying period and not the payments received within qualifying period alone, shall be considered. In case, final Bill of similar nature of work has not been passed and final measurements have not been recorded, the paid amount including statutory deductions will be considered. If final measurements have been recorded and work has been completed with negative variation, then also the paid amount including statutory deductions will be considered. However, if final measurements have been recorded and work has been completed with positive variation but variation has not been sanctioned, original agreement value or last sanctioned agreement value whichever is lower shall be considered for judging eligibility.
In case JV firms are allowed to participate, Technical Eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.1 of J.V. guide lines of IRSGCC April-2022 [read with up to date correction slip].
The value of work completed will not include the cost of any materials issued free of cost by the Railway/ Department concerned. Price Variation amount, if any; if indicated / incorporated in the experience certificate will also be considered towards eligibility.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organization, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates
The work experience certificate shall be in the name and style of the tenderer participating or as per provisions under Clause 17.15 of GCC April-2022 for JV Firm, if eligible to participate. [with up to date correction slip]
The work experience certificate shall be issued by an officer not below the rank of JA Grade or Bill passing Officer in Railways and Bill passing Officer/Executive In-charge of work in other Govt. / Govt. bodies / PSUs. The certificate should bear the signature and seal of the issuing officer, name of the department etc. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
84 conditions · 5 needing a document upload
Uploading of Proforma -01 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), when balance sheet for the first previous year is yet to be prepared/audited.
(i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii) documents shall be submitted according to clause 14 of IRGCC 2022:
Manual tenders, supporting documents etc., sent by Post/FAX/Courier or in Person SHALL NOT BE ACCEPTED
All requisite documents are to be properly submitted online only and the bidders should ensure that the content of the documents uploaded is distinctly legible /readable. Non-readable documents will not be considered and will not be asked again after tender opening date.
CORRIGENDUM NOTICE ON IREPS: Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh. For tenders valuing more than Rs. 50.00 lakh: The offer of Tenderer(s) who do not enclose Experience Certificate & Turnover Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted /received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railway reserves the right to verify the authenticity of the documents/information furnished
IRSGCC para 6.0 of part-I (a)(ii) Tenderers will examine the various provisions of The Central Goods and ServicesTax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates. (a)(iii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/ UTGST /SGST Act to railway immediately after theaward of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority. (a)(iv) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority. (b) When work is tendered for by a firm or company, the tender shall be signed by the individual legally authorized to enter into commitments on their behalf. (c) The Railway will not be bound by any power of attorney granted by the tenderer or by changes in the composition of the firm made subsequent to the execution of the contract. It may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor
Increase/decrease of TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works Contract is decreased or any tax/cess on Works Contract is decreased / removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
Fixed Deposit Receipts (FDRs) submitted after award of tender towards Security Deposit/Performance Guarantee should be with automatic renewal facility only.
Tenderer(s) shall note that conditional/alternate offer will not be considered and will summarily be rejected, even though such condition makes them as the lowest tenderer.
Shramik kalyan While processing payment of any 'On Account Bill' or 'Final Bill' or release of 'Advances' or 'Performance Guarantee / Security deposit', contractor shall submit a certificate to the Engineer or Engineer's representatives that "I have uploaded the correct details of contract labours engaged in connection with this contract and payments made to them during the wage period in Railway's Shramikkalyan portal at 'www.shramikkalyan.indianrailways.gov.in' till ____Month, ____Year.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website
A)An offer shall become invalid: - (i) if the Bid Security is not paid Online. (ii) if the offer is not digitally signed by the tenderer / by the Attorney / by the person authorized by the tenderer to sign and submit the tender on his/their behalf. (iii)if any individual/ Proprietor / Partnership Firm / Company /JV Firm/HUF/Society etc. uploads more than one offer either in his/their individual capacity or as a Proprietor or as a Partner/Member of Partnership Firm / JV Firm / HUF / Society etc. or as a Director of any Company, etc. B)An offer shall get summarily rejected if the following documents are not submitted /attached with offer as per the list mentioned in the tender documents: - (i) Documents as applicable in case of Proprietary concern/ Partnership firm / JV Firm / Company/HUF/Society/LLP Firm, etc. (ii) Annexure-V(A) linked under heading submission of Standard Format is to be submitted by the each member in case of a Partnership Firm / Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc.,. (iii) Ballast test certificate, if applicable. (iv) Any other document required for evaluation of the bid. C)An offer shall get summarily rejected if the tenderer adds any condition on his/their own (anywhere in the e-offer), which is in violation of the Railway's Tender Conditions. D) An offer shall become ineligible for award of the tendered work if the tenderer does not fulfil the Eligibility Conditions, (both the Standard Financial Eligibility Criteria and the Standard Technical Eligibility Criteria) prescribed in the Tender Documents and bid capacity if applicable
Bidders should carefully read all the conditions and the Special Conditions along with Special Conditions - General & Technical, which are annexed to the tender document in the DOCUMENTS attached to the tender. These special conditions form part of the tender document and will supplement to the conditions of GCC April - 2022 along with updated correction slips GCC April-2022. Where the provisions of these special conditions are at variance with GCC and other documents mentioned above, these Special Conditions shall prevail.
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN Rs. 10 CRORES, JOINT VENTURE (JV) FIRMS ARE ALSO CONSIDERED FOR ELIGIBILITY
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN RS. 20 CRORES: The tender/technical bid will be evaluated based on bid capacity formula detailed as Annexure-VI of IRSGCC April - 2022. NOTE: i)The Tenderer(s) shall furnish the details of existing commitments and balance amount of ongoing works with tenderer as per the prescribed proforma of Railway for statement of all works in progress and also the works which are awarded to tenderer but yet not started up to the of inviting of tender. In case of no works in hand, a 'NIL' statement should be furnished. This statement should be submitted duly verified by Chartered Accountant.(ii) In case, the tenderer/s failed to submit the above statement along with offer, their/his offer shall be considered as incomplete and will be rejected summarily.
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN RS. 50 CRORES: Electronic Reverse Auction (e-RA) method will be applicable as per guide lines issued by Railway Board vide Lr no. 2017/Trans/01/Policy/Pt-S Dt 28/3/2018. (Copy attached in the list of documents)
Price Variation Clause (PVC) is applicable If the advertised tender value above Rs.2 Crores. (As per letter No. 2022/CEI/GT/GCC2022/Policy dated 14.07.2022) As detailed in - Para 46A of IRGCC April - 2022 attached to the tender in - DOCUMENTS. Base Month: The Base Month for 'Price Variation Clause' shall be taken as the one month prior to closing of tender, unless otherwise stated elsewhere. The quarter for applicability of PVC shall commence from the month following the Base month. The Price Variation shall be based on the average Price Index of the quarter under consideration. [with up to date correction slip/ Railway Board Letter]
The Bid Security shall be deposited either in cash through epayment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per AnnexureVIA and shall be valid for a period of 90days beyond the bid validity period. In case, submission of Bid Security in the form of Bank Guarantee, following shall be ensured: (i).A scanned copy of the Bank Guarantee shall be uploaded on eProcurement Portal (IREPS) while applying to the tender. (ii).The original Bank Guarantee should be delivered to Chief Office Superintendent Rate before closing date for submission of bids i.e., excluding the last date of submission of bids. (ACS-5 dtd 20.10.2023). (iii)Non submission of scanned copy of Bank Guarantee with the bid on etendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. (iv) The Tender Security shall remain valid for a period of 90 days beyond the validity period for the Tender. (v) The details of the BG, physically submitted should match with the details available in the scanned copy and the data entered during bid submission time, failing which the bid will be rejected (vi).The Bank Guarantee shall be placed in an envelope, which shall be sealed. The envelope shall clearly bear the identification "Bid for the ***** Project" and shall clearly indicate the name and address of the Bidder. In addition, the Bid Due Date should be indicated on the right hand top corner of the envelope. (vii)The envelope shall be addressed to the officer and address as mentioned in the tender document. (viii).If the envelope is not sealed and marked as instructed above, the Railway assumes no responsibility for the misplacement or premature opening of the contents of the Bid submitted and consequent losses, if any, suffered by the Bidder
/We fail to submit the requisite Performance Guarantee [P.G] in the prescribed format even after 60 (Sixty days) from the date of issue of Letter of Acceptance, we are aware that the contract liable to be terminated duly forfeiting Bid Security and other dues, if any payable against the contract. Also, I/We
IN CASE OF ADVERTISED TENDER VALUE IS MORE THAN RS. 10 CRORES: Bid capacity is applicable, the tenderers should submit bid capacity as per proforma attached in tender DOCUMENTS. In case, the tenderer/s failed to upload BID CAPACITY PROFORMA along with offer, their/his offer shall be considered as incomplete and will be rejected summarily.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The work shall be maintained after completion for a period of 24 Months by the contractor and he shall make good any defects, imperfection shrinkages or faults which may appear at his own cost.
Tenderers are abiding by the General Conditions of Contract (GCC) April-2022 & any statutory modification thereof and also abide to carry out the work accordingly.
Tenderers are requested to visit the web site https//www.ireps.gov.in frequently till the closing date and time for any update.
Tenderer should have to upload only exact & specific, clear and readable documents, irrelevant documents should not be uploaded, and documents uploaded once should not be repeated
As per official Gazette Notification from "The Institute of Chartered Accountants of India( ICAI) (Set up by an Act of Parliament) dated 02/08/2019,Unique Document Identification Number (UDIN) has been made mandatory from 1st July, 2019 for all Audit/Assurance/Attest function.(Official Gazette Notification attached below).'ICAI has conceptualised and implemented an innovative concept called Unique Document Identification Number (UDIN). ICAI at its 379th Council Meeting held on 17th - 18th December, 2018 made generation of UDIN mandatory for every signature of Full time Practising Chartered Accountants in phased manner for the following services: 1) All Certificates with effect from 1st February, 2019 2) GST and Income Tax Audit with effect from 1st April, 2019 3) All Audit and Assurance Functions with effect from 1st July, 2019 Therefore, UDIN is being made mandatory for all Audit and Assurance Functions like Documents and Reports certified / issued by full time Practising Chartered Accountants from 1st July, 2019'.Any document verified by CA but not having UDIN No. (Wherever applicable) shall not be considered.
Development work at Osmanabad Good shed.
13-2026-SrDENCo
13-2026-SrDENCo
Open
Works - General
12 Months
Solapur, Maharashtra
₹0
₹28.1 L
27 May 2026
6 May 2026
13 May 2026
82 items across 2 schedules · ₹10,37,668.2 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. | cum | 150 | 494.1 | 74,115 |
| 2 | All kinds of soil | cum 3100 | — | 177.5 | 5,50,250 |
| 3 | Ordinary rock | cum | 440 | 498.9 | 2,19,516 |
| 4 | Hard rock (blasting prohibited) | cum | 50 | 1,432.95 | 71,647.5 |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. | cum | 100 | 196 | 19,600 |
| 6 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum 2090 | — | 7,878.5 | 1,64,66,065 |
| 7 | 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 80 | 7,294.7 | 5,83,576 |
| 8 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 110 | 9,895.2 | 10,88,472 |
| 9 | 1:1.5:3 (1 cement : 1.5 coarse sand (zone- III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) | cum | 110 | 9,045.75 | 9,95,032.5 |
| 10 | Foundations, footings, bases of columns, etc. for mass concrete | Sqm 1495 | — | 392.15 | 5,86,264.25 |
| 11 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. | Sqm | 250 | 842.5 | 2,10,625 |
| 12 | Suspended floors, roofs, landings, balconies and access platform | Sqm | 140 | 927.25 | 1,29,815 |
| 13 | Shelves (Cast in situ) | Sqm | 50 | 927.25 | 46,362.5 |
| 14 | Lintels, beams, plinth beams, girders, bressummers and cantilevers | Sqm | 170 | 736.4 | 1,25,188 |
| 15 | Columns, Pillars, Piers, Abutments, Posts and Struts | Sqm | 200 | 961.3 | 1,92,260 |
| 16 | Stairs, (excluding landings) except spiral- staircases | Sqm | 50 | 764.95 | 38,247.5 |
| 17 | Above 20 cm wide | Sqm | 425 | 879.05 | 3,73,596.25 |
| 18 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 388000 | — | 107.85 | 4,18,45,800 |
| 19 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg 25000 | — | 107.85 | 26,96,250 |
| 20 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 490 | 9,504.75 | 46,57,327.5 |
| 21 | Concrete of M25 grade with minimum cement content of 330 kg /cum | cum | 270 | 9,860.4 | 26,62,308 |
| 22 | Add for using extra cement in the items of design mix over and above the specified cement content therein. | Quintal 2740 | — | 733.5 | 20,09,790 |
| 23 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 60 | 7,132.25 | 4,27,935 |
| 24 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 80 | 9,105.95 | 7,28,476 |
| 25 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 70 | 9,095.05 | 6,36,653.5 |
| 26 | Second class teak wood | Sqm | 60 | 3,323.2 | 1,99,392 |
| 27 | 4 mm thick glass pane (weight not less than 10kg/sqm). | Sqm | 60 | 2,241.8 | 1,34,508 |
| 28 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | Sqm | 75 | 3,167.95 | 2,37,596.25 |
| 29 | On one side only | Sqm | 60 | 478 | 28,680 |
| 30 | 125x70x4 mm (ordinary type) | Each | 60 | 185.15 | 11,109 |
| 31 | 250x10 mm | Each | 60 | 441.6 | 26,496 |
| 32 | 300x16x5 mm | Each | 60 | 322.2 | 19,332 |
| 33 | 125 mm | Each | 60 | 256.65 | 15,399 |
| 34 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer's specification and direction of Engineer- in-Charge. | Metre | 75 | 492.7 | 36,952.5 |
| 35 | 30 mm thick pre laminated PVC door shutters | Sqm | 75 | 3,663.8 | 2,74,785 |
| 36 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg 21500 | — | 117.35 | 25,23,025 |
| 37 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. | Kg 60000 | — | 133.7 | 80,22,000 |
| 38 | Hot finished seamless type tubes | Kg 150000 | — | 206.35 | 3,09,52,500 |
| 39 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. | Kg 1500 | — | 97.2 | 1,45,800 |
| 40 | 40 mm thick with 20 mm nominal size stone aggregate | Sqm | 110 | 614.2 | 67,562 |
| 41 | 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. | Sqm | 80 | 978.45 | 78,276 |
| 42 | Size of Tile 600x600 mm | Sqm | 150 | 1,553.45 | 2,33,017.5 |
| 43 | 110 mm diameter | Metre | 60 | 377.4 | 22,644 |
| 44 | 110 mm bend | Each | 15 | 150.35 | 2,255.25 |
| 45 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm 5000 | — | 738.65 | 36,93,250 |
| 46 | 1:4 (1 cement: 4 fine sand) | Sqm 1000 | — | 399.45 | 3,99,450 |
| 47 | New work (three or more coats) | Sqm | 250 | 39.05 | 9,762.5 |
| 48 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre | Sqm | 400 | 185.65 | 74,260 |
| 49 | New work (Two or more coats applied @ 3.84 kg/10 sqm) | Sqm | 250 | 116.9 | 29,225 |
| 50 | With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood | Sqm | 50 | 74.65 | 3,732.5 |
| 51 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) | Sqm | 30 | 36.1 | 1,083 |
| 52 | Two or more coats on new work | Sqm | 95 | 155.9 | 14,810.5 |
| 53 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. | Sqm 17600 | — | 218.9 | 38,52,640 |
| 54 | Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). | cum 2650 | — | 24.85 | 65,852.5 |
| 55 | 90 mm to 45 mm size stone aggregate | cum 2650 | — | 2,098.4 | 55,60,760 |
| 56 | 63 mm to 45 mm size stone aggregate | cum | 150 | 1,636.05 | 2,45,407.5 |
| 57 | Moorum | cum 2750 | — | 768.25 | 21,12,687.5 |
| 58 | Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . | cum 5130 | — | 1,046.95 | 53,70,853.5 |
| 59 | Cement concrete prepared with batch mixing machine | cum 3950 | — | 10,529.35 | 4,15,90,932.5 |
| 60 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests | Each | 15 | 6,767.4 | 1,01,511 |
| 61 | One urinal basin with 5 litre white P.V.C. automatic flushing cistern | Each | 15 | 6,258.75 | 93,881.25 |
| 62 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer | Each | 10 | 3,960.55 | 39,605.5 |
| 63 | 32 mm dia | Each | 10 | 119.55 | 1,195.5 |
| 64 | Providing and fixing 100 mm sand cast Iron grating for gully trap. | Each | 10 | 53.25 | 532.5 |
| 65 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | Each | 10 | 1,607.95 | 16,079.5 |
| 66 | 1620 (20 mm OD) pipe | Metre | 50 | 331.2 | 16,560 |
| 67 | 25 mm dia nominal bore | Metre | 50 | 551.7 | 27,585 |
| 68 | 50 mm dia nominal bore | Metre | 50 | 1,048.35 | 52,417.5 |
| 69 | 15 mm dia nominal bore | Metre | 50 | 322.15 | 16,107.5 |
| 70 | 15 mm nominal bore | Each | 20 | 353.25 | 7,065 |
| 71 | 15 mm nominal bore | Each | 20 | 353.25 | 7,065 |
| 72 | 25 mm nominal bore | Each | 20 | 622.4 | 12,448 |
| 73 | 50 mm nominal bore | Each | 8 | 1,026.65 | 8,213.2 |
| 74 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. | Per Litre 4000 | — | 11 | 44,000 |
| 75 | 100 mm diameter | Metre | 50 | 443.6 | 22,180 |
| 76 | 300 mm dia. R.C.C. pipe | Metre | 50 | 994.3 | 49,715 |
| 77 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 50 | 495.05 | 24,752.5 |
| 78 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) | Kg | 50 | 598.6 | 29,930 |
| 79 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) | Sqm | 30 | 1,176.8 | 35,304 |
| 80 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. | Sqm | 600 | 617.05 | 3,70,230 |
| 81 | Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:(a) after surface preparation, first layer of slurry of cement @ 0.488kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured. | Sqm | 600 | 688.9 | 4,13,340 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022-uptoACS10.pdf
ATTACHMENT
PCEcircular207.pdf
ATTACHMENT
PCEcir208.pdf
ATTACHMENT
AddlSplconditions.pdf
ATTACHMENT
LETTEROFCREDITASMODEOFPAYMENT062018.pdf
ATTACHMENT
ProcedureforpaymentofContractorbillasperGSTImplementation_GST_290617.pdf
ATTACHMENT
EMPLOYMNTOFRETIREDRAILWAYOFFICERSCERTIFICATEFORMAT.pdf
ATTACHMENT
DETAILSOFPERSONNELPLANTANDMACHINERYWORKSONHANDFORMATS.pdf
ATTACHMENT
AnnexureVIB2025.pdf
ATTACHMENT
NEFTFORM.pdf
ATTACHMENT
proforma1previousyearbalancesheet.pdf
ATTACHMENT
Proforma2-LClessthan10cr.pdf
ATTACHMENT
Proforma3-LCmorethan10Cr.pdf
ATTACHMENT
ImplementationofContractore-MeasurementBook.pdf
ATTACHMENT
SPECIALCONDITIONSOFCONTRACT.pdf
ATTACHMENT
BIDCAPACITYUMDGOODSSHED.pdf
ATTACHMENT
GCCACS111.pdf
ATTACHMENT
PCSOSafetyCircular.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .