Construction of New Muthalvar Padaippagam at Mangalapuram

Amount

DISMANTLING WORKS

Dismantling Reinforced cement concrete by manual or by deploying machineries without damaging the near by structure and clearing away from work site.

Dismantling the existing brick or stone masonry work in cement mortar under 3m high including carefully clearing the debris etc.,complete.

Dismantling, clearing away and carefully stackingmaterials useful for re-use for any thickness of walls

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete SS.20B 10 cum

UP TO 2M LIFT

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Supplying and filling of Gravel by lorry in basement filling including conveyance loading and unloading consolidating with larger of 300mm thick including Power roller 8-10 tonne and water springler charges and all other incidential charges laying watering labour and consolidation etc., complete as directed by the Dept., Officers with standard specification.

Supplying and filling in foundation and basement with filling M sand in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four crushed stone sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and erecting centering for sides and soffits including supports and strutting up to 3.30 m height with all cross bracing for plane surfaces as detailed below, using mild steel sheets of 90 X 60 cm 10 gauge stiffened with MS angle of 25 X 25 X 3mm for boarding, laid over adjustable span & jacks and supported by 50mm dia pipes for general pipes scaffolding systems @ a spacing of 1.20m c/c and vertical connected at a height of 2.0m c/c including 'C' & 'U' clamps and base receiver cup at bottom for connecting pipes etc and removable systems etc.,Rate to include all materials, labour charges, wastages , placing, transportation, lead & lifts, tools & plants, fuels, fixing in position at all levels, heights, masking tape in sheet joints, consumables, etc. as complete with all respects complying with relevant standard specification, as directed by the Client / Engineer-in-charge.

For Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, raft slab / beams and such other members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

for plane surfaces such as rectangular or square rcc columns, sunshades, top and bottom slab of rcc boxing, etc.

For plane surfaces such as VERTICAL WALLSf RCC boxing, etc.

Providing and Laying M 30 Design Mix for all reinforced cement concrete with minimum cement content conform to IS 456-2000 using ordinary Portland cement of grade 53 from approved manufacturer, manufactured sand, 20 mm and down graded size coarse aggregates, necessary approved admixtures as per requirement. works for Raft, Grade beam, Shear wall, RCC walls, Lift walls, Plinth beams, Column, footings, Grade slab, Roof slab & beam, Curved slab, beam, Column drops, Pergola, Staircase waist and landing slab lintel, Sunshades, parapet Cum drops, Steps, canopy, window boxing slab, Loft, fins facia Planter box binders basement retaining wall, machine foundation, elevation features and other similar structures etc..excluding necessary centering, shuttering and reinforcement which shall be measured and paid separately under relevant items. Rate to include all leads, lifts, tools & plants, fuels, all materials, labour charges, wastages , laying, pumping the concrete to all levels, providing sleeves / openings in RCC slabs, compaction by vibrator, curing etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer in charge

Foundation

For Ground floor

For First floor

For Second floor

Supplying, fabricating and fixing in position of steel Fe 550 grade Reinforcement for all RCC work with Thermo Mechanically Treated Bars (TMT) conforming to IS 1786 of latest version according to drawings and binding the reinforcement with 18 gauge double fold GI binding wire and providing Concrete cover blocks to maintain the cover as required. The rate including cost of all materials, bending, tying grills, placing, transportation, lead & lifts, tools & plants, fuels, all materials, labour charges, wastages, laying at all levels, fixing in position, cost of cover blocks and GI binding wires etc. as complete with all respects complying with relevant standard specification, as directed by the Engineer-in-charge

Supply and constructing Fly ash Brick masonry in Cement Mortar 1:5 (One cement and Five M sand) in foundations, basement and superstructure using Fly ash Bricks of size 230x110x75mm etc. Rate to include all materials, labour charges, wastages for working at all levels with necessary lead and lifts, transportation charges, loading, unloading, scaffolding, staging, curing, fuel, consumables as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

In Basement floor

In Ground floor

In First floor

second floor

Brick partition walls of 11.50cm thickness using best quality Fly Ash Bricks of size 23 x 11 x 7 cm in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground floor

First floor

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Crushed stone sand ), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with cement mortar 1:4 (One Part of Cement and Four part of Plastering Sand (P- Sand)) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications (S.I.309)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Supplying and fixing Dadooing the wall with ceramic tiles of approved quality, colour and design joint free of size 600x300x10mm thick of approved make, in all floors over a base layer of cement mortar 1:2 (one cement: Two sand) 10mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40 kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications. The rate including cost of all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick laid in-situ and pointed with same coloured cement

Paving the floor with Double charged Vitrified tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Executive Engineer before use on work

Supply and Laying flooring with designer Cement Concrete Square Tile of size 416mm × 416mm thick not less than 30 mm thick of approved colour / pattern of specified shape & size (as per drg) with grooves, raised chequers of varying size and intermediate flat surfaces, with different levels to provide suitable antiskid features, manufactured by vibration compaction of polymerized concrete conforming to the norms of wet transverse strength, water absorption and wear resistance as per IS 1237, with a minimum of M40 grade concrete laid over a bed of CM 1:4 (1 of cement : 4 of manufactured sand), 20 mm thick including jointed with matching cement slurry, matching corner tile beading and including preparation of base surface. Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, washing over finished surface, necessary protection and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Supply and fixing wall dado with best quality approved make White Glossy ceramic tiles sizes 300 x 300 mm x 6 mm thick set in CM 1:3 (1 of Cement : 3 of manufactured sand) 10mm thick and pointing with white cement and as directed. Rate shall include for preparation of base surface, and finishing the surface, cleaning the surface, work at all levels etc. as complete and as directed by the Engineer-incharge (For Over Head Tanks & U.G.Sump) Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting of tiles to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Client / Engineer-in-charge.

Supply and laying with best quality the following materials of Machine Polished granite slab of 18 mm thick (Fine Polished Steel Grey Granite Slab) including cutting and edge polishing to be set in CM 1:3 (1 of cement : 3 of manufactured sand) 20 mm thick including finishing the joints with white cement slurry, cutting, edge chamfering to approved shape and polishing rough, medium, nice and tin-oxide polish.Rate including all materials, labour charges, wastages, necessary lead and lifts, working at all levels, transportaion charges, loading, unloading, preparation of surface, ncessary haccking in RCC surface, cutting to required shape, edging, tools and plants, fuel, curing, cleaning, acid wash over finished surface, protection with Gypsum / Pop layer over plastic sheet and removing the same before handing over as complete with all respects complying with relevant standard specification and as directed by the Engineer-in-charge.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete (PWD SOR P.NO : 61)

Manufacturing, Supplying and Fixing of Stainless Steel Handrails for staircase near wet riser using 50mm dia 304L GradeStainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipeof 25mm dia of 1.60mm thick welded to the railing. Thesupports will be grouted into the wall and provided with93.00mm thick Stainless Steel circular base plate of 304Grade. The rate shall included for grouting into concrete withnecessary supporting arrangements the hand rail in floorpolishing buffing, bonding, cutting, grinding, conveyance,welding charges, electrical charges, etc. complete

Finishing the top of roof with one course of Solar Reflective ceramic tiles of size 305 mm x 305 mm x 7 mm of approved quality in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete.-10 cum

Providing Polymer Coating ( Water Proof Coating ) for basement portion & toilet sunken portion with following specification and the surface shall be cleaned to remove all dust,foregin,matters lose matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio asper recommendation of the supplier. the mix shall be stirred thoroughly until 1 NO (ONE NUMBER) bubbles remain in the mix. any lumps found in mix shall be removed. apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. after drying,second coat shall be applied on the first coat as directed by the departmental officers etc. the rate inclusive of cost of materials and labour etc., complete

Providing and laying to required line and grade as per the drawing interlockingcement concrete Paver blocks of M 30 grade 83 mm thick laid over the sand cushion . The size and the shape of the concrete blocks had to be approved before sourcing / manufacturing the same. The gaps between the two blocks shal be filled with relatively finer sand than the bedding sand of gradation as per Table 2 . The paver blocks shall be compacted using a light tandem roller or plate compactor till the required grade and line is achieved. The rate shall include laying of the bedding sand levelling , laying of paver blocks , filling of the filling sand and compaction etc. complete and as directed by the Departmental officers.

Providing and Laying, Spreading and Compacting graded stone aggregate to Wet Mix Macadam (WMM) specification including premixing the materials with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density complete as per clause 406 of MORTH Specifications.

Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor spring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality. The vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers M-0713 VOL-1 P.NO: 117

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work (pwd sor p.no 70)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work (pwd sor p.no 71)

ABS DOOR / EQUIVALENT Specification:Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work

Structural Glazing: Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of ‘D’ quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875. Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm.Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections.Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by using nylon self–expanding cap and driving MS electro plated 80mm long screws into the caps through frames.Glass: 5mm reflective Saint Gobain OR equivalent.

Supply and fixing of Dorma ES 250 Pro Easy Automatic sliding door operator; 4.15 mtr; With lock Hardware set : Dorma Glass Clamping Rail - 1050 mm - 2 nos Floor Guide for glass door - 2 nos Nemo Motion + Nemo Dual ( Safety& Motion) Combo Pack - 1 no Five Position Program Switch with Knob - 1 no Cable for Program Switch (5M) - 1 no IS5160H Brush Profile - 2 nos Soft nose seal - 2 nos 12mm Toughened glass panel of size 750 x 2400mm - 2 nos

supply, installation labour, installation material and transportation of Brick jolly including 5% wastage. Smooth finish. actual coverage area -201 sqft.

Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of "U" clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm]

Internal Water Supply - CP.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

Outer line

65 MM DIA

Internal line

50 MM DIA

32 MM DIA

25 MM DIA

20 MM DIA

Supplying & fixing in position first quality & approved variety of 50mm dia C.P.V.C Ball Valves ( Heavy type ) with I.S.I. Mark of the following size including cost of Shellac, thread etc.,including labour for cutting & threading of Pipes etc., complete complying with standard specifications for both internal & external water supply arrangements.

25mm cpvc ball valve Valve

32mm cpvc ball valve Valve

Suppling and fixing in position 15mm.diameter brass / C.P screw down tap / pillar tap (heavy duty) of approved make conforming to I.S.specifications and quality including cost of shellac, thread etc.complying with standard specifications and including cutting and threading wherever necessary (D)

SD Tap

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.

110 mm dia Pipe

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed

Coupler

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Elbow

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Union

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Reducer

25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Reducer Tee

25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Reducer Elbow

25 mm x 20 mm

32 mm x 25 mm

50 mm x 40 mm

Hex Nipple

25mm dia Pipe

32mm dia Pipe

50mm dia Pipe

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications

Supplying and fixing in position indian make bewelled edge mirror of approved quality and brand of size 600 X 450mm wth necessary plastic back, PVC frame with bottom stand of approved colour with brass screws,rawal plugs etc., complete complying with standard specifications.

Supplying and fixing the best quality approved make of bip cock with C.P. health faucet wall hook one metre long flexible tube, angle cock with wall flange including cutting and making good the walls wherever required etc.complete, complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Executive Engineer before use on work.

Supply and delivery of Open well Submersible pump set conforming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50 Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation.

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days

Erection of power pumps inborewell labour charges for erection of twin packer duplex type jet pumps in borewells upto150mm dia including fixingof Suction pipe regulating valves with jet assembly upto a maximum depth of 30 mand delivery pipe valve pressure gauges upto the exterior wall of pump roomand erection of panel board consisting of TPICN switches starter, Voltmeter,Ammeter, three indicator lampscapacitorand laying and jointing the cables and twinearthing as per IE rules etc., complete and testing the pumps and trail run for10days including signing ofcompletion of reports as required by EB authorities and finishing thepipeholes including the foundation bolts, nuts and earth pits.

Supplying and erecting in position of 250 liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact(250lts) (PWD SOR PG NO 118)

Supplying and fixing White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge. (Make Jaguar URS-WHT-13253N or Equivalent)

Supply and fixing in position white European Water Closet (single piece or wall mounted) of approved make with low level concealed flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.(Make Parryware Claret Rimless Single Piece Suite S220 C8640 or Equivalent

White glazed European Water Closet with 10 litre capacity PVC flushing tank fixed on to wall

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three Crushed stone sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.(D)

Providing rain water harvesting using 3 nos.of R0.45 well rings of 90cm inner dia (clear) with 5cm wall thickness made out of cement concrete 1:2:4 using 20mm hard broken jelly to a height of 30cm each supplying and fabricating 16 nos. of 6mm dia MS rod vertically and 3 nos. of 6mm dia MS rod circumferentially tied together with 18 guage binding wire for well rings including necessary earth work excavation 1m dia to a depth of 1m, supplying and filling 40mm HBG inside the erected well ring to a depth of 90cm, and top covered with R0.45 circular perforated cover slab of 1m dia and 5cm thick which inclusive of cost and fabrication of 6mm M.S reinforcement at 15 cm spacings on both directions and one 6mm M.S rod ties at the edge of the slab circumferentially including cost of moulding, curing, finishing and well placing in position and disposing off excavated earth with all initial leads and lifts in places as shown by the Departmneal officers etc., complete in all respects.

Constructing Brick Work Masonry manhole various size of deep in cement mortar 1:3( 1 Cement: 4 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame of size 600x600 mm , PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Executive Engineer before use on works) (SOR)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supply & stacking of red earth at site to the departmental guage for pre measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading and stacking etc.,completeand and as per the standard specification.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth. The rate includes cost of transportation, loading, unloading and stacking etc.,complete and as per the standard specification.

Mixing charges of Red soil, sand and manure uniformly for Preparation of soil mixture (excluding material cost)

Truffing of Korean grass / mexican grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Planting of Bamboo grass ornamental foliageshrub variety of height 30-45 cm inpolythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavatedearth etc as directed by the site in-charge PD-1633

Planting of Duranta new gold Plantornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size, planting of sapling, refilling of excavatedearth etc as directed by the site in-charge.PD-1650

Planting of Ixora dwarf foliage Specimenplant variety of height 105-120 cm inpolythene bag of size 16x16 inch including loading andunloading charges, transportation, stackingof saplings at site, earth work excavation ofrequired size, planting of sapling, refilling ofexcavated earth etc as directed by the site in?charge PD-1739

Planting of Bougainvilla foliage shrub varietyof height 30-45 cm in polythene bag of size6x7 inch including loading and unloadingcharges, transportation, stacking of saplingsat site, earth work excavation of requiredsize, planting of sapling, refilling of excavatedearth etc as directed by the site in- charge.

Planting of Ficus black ornamental foliageshrub variety of height 30-45 cm inpolythene bag of size 6x7 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavatedearth etc as directed by the site in-charge PD-1656

Planting of Ficus panda ornamental foliage Specimen plant variety of height 105-120 cm in polythene bag of size 16x16 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in?charge . PD-1736

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the departmental Officers. (Make: Ravel / Equivalent)

First Aid Box complete with all First Aid Medicines

4 Nos of Fire Buckets made out of 40x40x6mm MS Angle

INTERIOR WORKS

FALSE CEILING WITH GYPSUM BOARD Providing and fixing suspended false ceiling using SAINT - GOBAIN GYPROC or Equivalent make which includes providing and fixing GI perimeter channel of size 0.50mm thick having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall / partition with the help of nylon sleeved and screws at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thick with two flange of 15mm each from the sofit at 1220mm centres with ceiling angle of width 25mm x 10mm X 0.55mm thick fixed to sofit with GI cleat and steel expansion fasteners. ceiling section 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lops of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 610mm centres. 12.5mm Gypboard

Providing and fixing of brick cladding 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included to fix the main frame with necessary clamps, fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer

LT CT TNEB METER BOX: CT Metering Panel - Supply, installation, testing and commisioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, complete with electrolytic grade copper bus bars, internal wiring, colour coding, ferrules, Panel mounting MS channels, fasteners, etc., including all associated control wiring. 1set of 250/5A CT with TNEB Metering provision and 1nos of 250/5A CT for APFCR.

MAIN LT PANEL: Supply, Installation, testing and commissioning of 3Phase, 415Volts, Main LT Panel board of Indoor, Cubicle floor mounting type made out of 2mm thick CRCA Sheet with powder coated finishing, MS base frame, double internal earthing arrangements, 100Amps, rating TPN Copper busbars with interconnection busbar, etc., comprising of the followings: EB Incomer : 1 No. 100Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM DG Incomer: 1 No. 100Amps, 25kA, 4Pole, Thermal magnetic MCCB with Ext.RHOM Common C/O Incomer: 1 No. 100Amps, 4Pole Automatic Changeover Switch with EB ON and DG ON LED Indication lamps Metering : 2 Set of RYB LED Indication lamps 2 Nos. of Multifunction Meter with RS 485 2 Set of Current Tranformers (100/5A, Cl-1), 1 No. 100/5A CT for APFCR 2 Set of Control MCB and Electrical Interlocking between EB & DG Incomers Outgoings: 4 Nos. 63A, 25kA, TP+N, TM MCCB with spare compectment (As per quotation)

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only. i.63A 4P MCB - 1 no. ii.63A 4P 30MA RCCB/ELCB - 1 no. iii.63A DP MCB Isolator -3 nos. iv.6A to 32A SP MCB - 24 nos. (SD629 / Pg 273)

Supply and Laying of 3 1/2 x 70 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 3 1/2 x 50 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection

Supply and frxing of brass cable gland for 3-1/2 x 50 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of brass cable gland for 4 x 16 Sq.mm PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3-1/2 x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and providing cable end termination of 4 x 16 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and Run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed FRLS copper wire with painting of suitable colour.

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - PRIMARY POINTS

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End - SECONDARY POINTS

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet for all 4 floors with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in suitable PVC rigid pipe on wall and ceiling with PVC accessories , 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and erection of 40-63Amps, 4Pole MCB with IP65 rated thermoplastic enclosure

supply and fixing of 18W LED Round type Recessed fitting with LED (Higher end) on false Ceiling from ceiling with PVC unsheathed copper leads from terminals to the fitting.

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply, fixing, testing & commissioning of 40W LED Pendant (Direct)- indoor luminaire with soft & uniform light distribution. Luminaire made up of Extruded aluminium with Die Cast End Caps - powder coated finish in RAL9004 Signal Black fine texture I RAL9016 Traffic White fine texture I RAL 9007 Grey aluminium fine texture. Dimension : 1188mm X 36mm X 75mm with Standard suspension kit 1Mtr/2Mtr. Diffuser / Lens material : Polycarbonate & Secondary Refelector Hexa-Cell (Matte Black). Cable entries for through-wiring of mains supply cable Prewired with LED driver and suitable for operation on 240V, 50Hz single phase ac supply. Operating voltage range (90 - 265V AC). LED driver efficiency should be >85% & Optical efficieny >90%, CRI greater than 80 and with colour temperature 4000K range. LED having 60,000 burning hours with minimum 70% lumen maintenance and power factor > 0.9, UGR < 16, SDCM≤3. Surge Protection : 4kV-6kV. System consumption should be 40W LED fixture with lumen package of 1835 lumens (100 lm/W). The luminaire shall be wired with PVC unsheathed copper leads from terminal to the fitting. Luminaire should have NABL Certificate on Resitance to Flame & Ignition as per IS 10322 Part-1:2014. Mandatory CE Marking & BIS Certified. Make: K-LiTE (Model No. 3456)

Supply and fixing of 450mm (18") Wall mounting 5 star rated complete(Higher end) with necessary accessories and hardwares as required.

Supply and fixing of 300mm (12") sweep(Heavy Duty) AC exhaust fan complete with necessary wall opening and making good of the wall .

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep AC exhaust fan

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and erection of Copper plate earthing station with GI pipe, 600x600x3mm thick copper plate, salt, charcoal, etc., including civil works, heavy duty CI Cover, etc., as per IS 3043 standards

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and Run of 1 of No.8 SWG copper wire for earth connection

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

The cable rack shall have runners rugs of suitable size, horizontal elbow, vertical elbow 90 Deg. Up vertical elbow 90 Deg. Down, re-deep, coupler plates, materials. The cable racks shall be suspended from ceiling supported from side walls in columns etc. with adequate size supporting angles / channels with fasteners, welding, anchor bolts, nuts etc. The rack shall have suitable cable clamping arrangements etc.' Cable Tray /ladder should be powder quoted as match with ceiling colour as per PWD requirements. The rate shall inclusive of necessary Wedge anchors threaded rods,nuts & bolts, making clamp for rcc roof fix / perlin/Truss, cable tray clamps etc, (8 mm threaded rod supports shall be provided at not more than 2 mtr center to center and as per site requirement )

Perforated type Supply and fixing of GI Hot Dip / Powder Coated 16 SWG Cable Tray with 150 mm width and 50mm height

Supplying and fabricating of MS structural steel supports for various applications using U channels, MS angle iron, bolts, nuts, anchor bolts etc., required for the work, cut to the size, bent to shape, welding, grouting etc., complete. Supports shall be powder coated with required colour for different system as mentioned above.

METAL SIGNAGE BOARDS: Supply and fixing of metal signages for the following: 1. Mudhalvar Padaipagam text in Tamil of size 2'0" x 15'with backlit LED placed over the base, fabricated using stainless steel sheet of minimum 16G thickness brush finish of required size and colour as required.

LOGO SIGNAGE BOARDS: Supply and fixing of acrylic signages for the following: 1. Mudhalvar Padaipagam logo of size 2' x 2' 2. CMDA logo of size 3' x 4'6" 3. Directorate of Public Libraries logo of size 6' dia with backlit LED placed over the sun board base, SIDE EDGES(4"): 5mm transparent white acrylic sheet with laser cut & 4inches manual raising all around with details. ACRYLIC SHEETS & ITS TECHNICAL PARAMETERS: Front: a. 5mm Imported (Mitsubishi/equivalent) acrylic cutting on laser cutting machine. b. Flexi bond make 25mm Sun board for the back of the logo.

Supply, Installation, Testing and commissioning of 16 channel 2 SATA NVR, with 8TB Hard Disk Drive 2 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback. and smart playback to improve the playback efficiency,Supports VCA search for fire/ship/temperature/temperature difference detection triggered video files, POS information overlay on live view and playback, POS triggered recording and alarm Network & Ethernet Access  Hik-Connect for easy network management, 2 Gigabit Ethernet network interfaces.

Supply of 4MP, Internet Protocol fixed BULLET CAMERA/DOME CAMERA (INDOOR & OUTDOOR)with following specification: ●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection) ● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied ●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB, ● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W ● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse. with Camera Stand. (Rate as per Quotation)

Supply, Installation, Testing and Commissioning of 32" smart LED TV with following specifications a) Full HD 4K monitor b) 2 Speakers, HDR, Dolby Vision c) HDMI -3nos d) USB -3nos e) Wifi, Ethernet f) 16GB storage

Supply and Clamping of CAT 6 unarmoured cable in suitable PVC Pipe 1" thick on wall / ceiling with connected PVC accessories with clamps, saddles etc., complete. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser), Tertiary(Horizontal) IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-T IEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch with two uplink port, 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply and fixing of POE 8 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line. (Make: DLINK,NETGEAR/ TPLINK)

Supply & Installation of CAT 6 PVC Module Box I/o socket & face plate single socket Erection and arrangement chargers (Higher end)

Supply and fixing of LAN Network Switches Fully-Managed 10/100/1000 with 1G Uplink - 24 Port with fibre port switch and 24 Port Patch Panel- Unloaded erection and arrangement chargers.

Supply and Fixing of Rack with Accessories -Higher end 12u Rack with fan extra for the above rack. (speaker/data/cctv)

Supply and Fixing of Rack with Accessories -Higher end 6u Rack with fan extra for the above rack. (speaker/data/cctv)

SRM ENTERPRISES (BID ID -1390514)

SHRINIDHI INFRRA (BID ID -1389138)