Spl repair to building No. P 60, P 184 and certain other works at Naria BHU Varanasi under GE (East) Allahabad.

Amount

Excavation in trenches not exceeding 1.5m deep & not exceeding 1.5m wide or area not exceeding 10 Sqm on plan& depth not exceeding 1.5 m in any type of soil and getting out for foundation, trenches for laying of electric cable or pipes complete all as specified & directed.

Returning, filling in, excavated soil including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete all as specified & directed.

Removal of excavated materials (soil) to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified & directed.

Material & Labour PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation filling or mass concrete or similar wrok complete all as specified & directed.

Material & Labour 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in sub base to floor or plinth protection or similar wrok complete all as specified & directed.

Material & Labour 100 mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in sub base to floor or similar wrok complete all as specified & directed.

Material & Labour 75 mm thick PCC 1:3:6 type C-1 using 20 mm graded crushed stone aggregate as in plinth protection or similar wrok, finsihed even & fair including laid in panel and making joints on full depth and filling with mixture of Bitumen & sand in ratio of 1:3 to entire depth complete all as specified & directed.

Material & Labour 40 mm thick PCC 1:2:4 type B-1 using 20 mm crushed stone aggregate as in sub base to floor or paving or similar wrok including glass dividing strip complete all as specified & directed.

Material & Labour for 300 x 300 mm x 25 to 30 mm thick full coloured paving tiles, heaving top of tiles wear resistant coat of approved design laid with neat cemrnt slurry @ 3.0 Kg per Sqm over & including 15 mm thick Screed bed or bedding layer in cement sand mortar in 1:6 for laying of tiles complete all as specified & directed.

Demolition of brick work built in cement or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facing, dresssed stonework and precast concrete atrticles complete all as specified and directed.

Material & Labour for brick work with fly ash bricks [crushing strength not less than 75 Kg per Sqcm] straight or curved on plan exceeding 6 m mean radius built in cement sand mortar 1:6 complete all as specified & directed.

Material & Labour for brick work with fly ash bricks [crushing strength not less than 75 Kg per Sqcm] straight or curved on plan exceeding 6 m mean radius built in cement sand mortar 1:4 complete all as specified & directed.

Material & Labour for reinforced cement concrete M-25 grade design mix using 20mm graded crushed stone aggregate as in foundation including rafts, footing, foundation beams, plinth beam, base of coloumn etc & mass concrete complete all as specified & directed.

Material & Labour for reinforced cement concrete M-25 grade design mix using 20mm graded crushed stone aggregate as in coloumn, pillars, piers, posts & struts or similar works complete all as specified & directed.

Material & Labour for reinforced cement concrete M-25 grade design mix using 20mm graded crushed stone aggregate as in beam, cantilever beam or lintel over 1.5m span or similar works complete all as specified & directed.

Material & Labour mild steel TMT bars 8-10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed.

Material & Labour mild steel TMT bars 6 to 8 mm dia used as in stirrups, spacer bars & binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed.

Material & Labour formwork to sides & soffits of concrete foundation, footings, bases of columns, rafts, raft beams of foundation and plinth beams; and similar work; vertical or batter, finished rough finish surfaces of concrete complete all as specified & directed.

Material & Labour formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular finished rough surfaces of concrete complete all as specified & directed.

Material & Labour form work to soffits of suspended slabs such as roof slabs, floor slabs, landings slab and similar work; not exceeding 200 mm thick (Horizontal or slopping) rough finished flat surfaces complete all as specified & directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding & backing complete and removing of rubbish from site complete all as specified & directed.

Material & Labour for Non Skid Jointless ceramic light coloured tiles 7-8mm thick [premium quality] (square or rectangular) area of each tile exceeding 0.11 Sqm and not exceeding 0.18 Sqm, laid in floors set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles over & including 15 mm thick Screed bed or bedding layer in cement sand mortar in 1:6 for laying of ceramic tiles complete all as specified & directed.

Material & Labour for Glazed ceramic coloured tiles [premium quality] as in vertical surface of walls such as skirting / dado and risers to steps, size of tile 450x300mmx7mmm or 350x250x7mm thick set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles over & including 10 mm thick rendering as in backing of tiles in cement mortar in 1:4 complete all as specified & directed.

Material & Labour for Non Skid Jointless ceramic light coloured tiles 6-7mm thick [premium quality] (square or rectangular) area of each tile exceeding 0.11 Sqm & not exceeding 0.18 Sqm, laid in vertical surface of walls like skirting or dado, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles over & including 10 mm thick Screed bed or bedding layer in cement sand mortar in 1:4 for laying of ceramic tiles complete all as specified & directed.

Taking down cement plaster on brick or stone walls or wall tiles etc including raking out joints, hacking for key, scrubbing down with water etc including removal of rubbish off the premises complete all as specified & directed.

Material & Labour for 10 mm thick rendering on fair face of brick wall or concrete surface surfaces in cement sand mortar 1:4, finished surface even and smooth without using extra cement complete all as specified & directed.

Material & Labour for 10 mm thick rendering on fair face of brick wall or concrete surface surfaces in cement sand mortar 1:6, finished surface even and smooth without using extra cement complete all as specified & directed.

Material & Labour for 15 mm thick rendering on fair face of brick wall or concrete surface surfaces in cement sand mortar 1:6, finished surface even and smooth without using extra cement complete all as specified & directed.

Material & Labour for 10 mm thick rendering on ceiling surface of brick work or concrete ceiling surfaces in cement sand mortar 1:4, finished surface even and smooth without using extra cement complete all as specified & directed.

Material & labour for three coats of white wash on newly plastered surface of walls after preparation of new plastered surface complete all as specified & directed.

Material & labour for three coats of white wash on newly plastered surface of ceilling after preparation of new plastered surface complete all as specified & directed.

Demolition of Concrete work in any description and in any position not exceeding 150 mm thick and removing rubbish from site as directed by Engineer-in-Charge.

Material & Labour for broken glass coping on top of walls, glass fixed in 20 mm thick cement sand mortar 1:3 complete all as specified & directed by Enginer-in-Charge.

Taking out old rusted or damaged 15 mm bore galvanised steel water tubing & connections for cleaning or re-fixing if required complete all as specified & as directed.

Taking out old rusted or damaged 20 mm bore galvanised steel water tubing & connections for cleaning or re-fixing if required complete all as specified & as directed.

Supply & Fixing 15 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings such as sockets, elbows, unions, Tees & short length etc, and fixed to walls with steel hooks or laid in floors in any length complete all as specified & as directed.

Supply & Fixing 20 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings such as sockets, elbows, unions, Tees & short length etc, and fixed to walls with steel hooks or laid in floors in any length complete all as specified & as directed.

Supply & fixing in repair 500 Litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including necessary connections to inlet / outlet & wash out pipes, including PTMT with epoxy coated aluminium rod & high density PVC float valve 20 mm dia screwed for iron pipe complete as specified in SSR Part-I complete all as specified & directed.

Supply & fixing in repair 1000 Litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including necessary connections to inlet / outlet & wash out pipes, including PTMT with epoxy coated aluminium rod & high density PVC float valve 20 mm dia screwed for iron pipe complete as specified in SSR Part-I complete all as specified & directed.

Supply & fixing in position 20 mm bore gun metal gate valve with iron wheel head screwed both ends complete all as specified & directed.

Supply & Fixing in repair 15mm bore bib tap cast copper alloy fancy type chromium plated with capstan head handle screwed down for iron pipes or for brass ferrule complete all as specified & directed.

Supply & Fixing in repair 20mm bore stop valves cast copper alloy screwed down high pressure with crutch or butterfly headed handle screwed both ends for securing iron pipe or for union complete all as specified & directed.

Supply & Fixing in repair 15mm bore stop valves fancy type Chromium plated (concealled type) cast copper alloy screwed down high pressure with capstan headed handles screwed both ends for iron pipe or for union complete all as specified & directed.

Supply & Fixing in repair 15mm bore Pillar tap cast copper alloy fancy type swan neck type chromium plated screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and fly nuts screwed for iron pipes complete all as specified & directed.

Supply & Fixing PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified & directed.

Supply & Fixing in repair vitreous china wash hand basin white flat back of size 550x400mm excluding chain & plug and porcelain stopper but including brackets, PVC waste pipe 32 mm bore 600mm long, chromium plated waste coupling 32 mm dia long shank complete as specified & directed.

Supply & Fixing in repair vitreous china squatting pan white orissa pattern of size 580 x 440 mm with Integral foot rests (excludig flushing cistern & flush pipe) with VC trap and make good to match with the existing surface of floor complete all as specified & as directed by Engineer-in-Charge.

Material & Labour 110 mm round steel chromium plated with or without centre hole grating fixed with adhesive or cementy solvant complete all as specified & directed.

Supply & Fixing in repair 10 litre capacity PVC valveless syphonic action type low level flushing cistern white colour including 32 mm bore flush pipe 600 mm long, cantilever brackets PVC ball valve, float and PVC handle, PVC connection 15mm dia 450 mm long complete all as specified & directed.

Taking down chowket or frame with shutter (without taking off shutters from the frame) area not exceeding 1.5 Sqm each complete all as specified & directed.

Taking down chowket or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 Sqm & not exceeding 4.0 Sqm each & removing from site complete all as specified & directed.

Supply & Fixing powder coated [minimum 50 micron thick] aluminium door frame with shutter having with door frame of section 62.5x37x1.5 mm thick & shutter with bottom & middle rail of section 112.5x37x1.5 mm thick and styles & top eail of section 83x37x2.5 mm thick with central locking arrangement with & including mortice handle lock of make of Godrej or Link having seven lever and self closing device [Floor door spring by cutting of floor of Sandhu make] with rebate including jointing cleats, fixing builder hardware fittings necessary numbers of sliding roller and glazing with 5.5 mm thick ordinary plain glass including aluminium snap beading & rubber packing and necessary fittings, fixtures complete all as specified & directed.

Supply & Fixing powder coated [minimum 50 micron thick] aluminium window frame of aluminium section 62.5x37x1.5 mm thick & shutter having styles & rails of section 44.45x44.45x1.5 mm thick including jointing cleats, glazing clips, rubber packing, aluminium snap beading, steel screws, aluminium anodised fitings such as 100 mm lung buttt hinges, 150 mm long tower bolt, 150 mm long handle including 5.5 mm thick ordinary plain glass including providing & fixing aluminium checquered grill of anodised section of size 100x100 [diagonally] of 8 mm dia die cast fixed to frame 20x20x5 mm aluminium flat with screws and stainless steel wire cloth of 0.36 mm nominal dia of wire and average aparture 1.4 mm complete all as specified & directed.

Supply & Fixing in repair 5mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in a square not exceeding 0.5 Sqm in each pane complete as specified & directed.

Supply & Fixing steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bars, dovetailed or welded joint complete all as specified & directed.

Supply & Fixing steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete with out glazing bars, dovetailed or welded joint complete all as specified & directed.

Supply & Fixing steel ventilator factory made with top hung shutter including hinges with steel handle, steel peg stay, dovetailed or welded joint complete all as specified & directed.

Material & labour for mild steel framed work such as grills, gratings with ends of bars shouldered and or riveted, or forged into spikes; framed guard bars, railings, hold fasts or similar work complete all as specified & directed.

Supply & Fixing 3mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads in a square not exceeding 0.5 Sqm in each pane complete as specified & directed.

Supply & Fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks or galvanized steel wire staples / beads in wooden or steel window complete all as specified & as directed.

Material & Labour for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified & directed.

Supply & Fixing solid PVC door frame of size 50 mm x 47 mm made out of 5 mm single side prelam PVC sheet & edges will be printed to match with prelam sheet reinforced with MS square tube complete all as specified & directed.

Material & Labour for 30 mm thick Factory made PVC solid panel door shutter (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and Plain colour PVC sheet for top & bottom rail, lock rail & bottom rail on either side and as gap insert for top & bottom rail; penelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as specified & directed.

Supply & Fixing 35 mm thick factory made plain framed panelled door shutters [Two or more panel] with lock rail and panel of 9 mm BWP commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces size of rail and style aas per IS : 1003 [Part-I], Kiln seasoned ASCU treated [chemically pressure treated] complete all as specifed & directed.

Supply & Fixing 35 mm thick second class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass / gauze etc divided into squares or rectangluar with plain, chamfered or rounded mitered edge beads for securing glass/ gauge complete all as specified in SSR Part 1-1991 section 8 clause 8.24 (a) complete all as specified & directed.

Supply & Fixing 100mm long mild steel butt hinges medium weight cold rolled with steel pin hinge and fixed with steel screws complete all as specified & directed.

Supply & Fixing 100mm long butt hinges made with stainless steel with steel pin type B-11 and fixed with steel screws complete all as specified & directed.

Supply & Fixing 150mm long extruded aluminium anodised alloy handle cast type and fixed with screws complete all as specified & directed.

Supply & Fixing 200mm long extruded aluminium anodised alloy barrel tower bolt fixed with screws complete all as specified & directed.

Supply & Fixing aluminium alloy anodized sliding door bolt with hasp & staple (clip & bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 250mm long complete all as specified & as directed.

Supply & fixing in repair door closer hydraulically regulated designation No-3, universal type, suitable for door shutters of weight between 61 Kg to 80 Kg of aluminium (Die cast) body complete all as specified & directed.

Material & Labour in repair for 1.25 mm thick steel rolling shutters, push or pull with gear operatedy type with bevel gear box and crank handle including top cover hood, anchoring rod, steel spring, hasp staple, erected in position, side rail fixed on wall including two coat of synthetic enamel painting on both side over one coat of red oxide primer after preperation of steel surface complete all as directed.

Taking out / down old damaged water proofing treatment from roof / concrete surface any type and removal from site as directed by Engineer-in-Charge.

Material & Labour for providing wate proofing treatment over cleaned roof surface with APP modified bitumen membrane 3 mm thick weight 3Kg per Sqm comprising of following and testing complete. [a] 10 mm thick rendering or screed in cement sand mortar in 1:4 mixed with water proofing compound @ 3% by weight of cement and surface finished even & fair. [b] Applying bitumen primer comforming to IS : 3384-1965 @ 0.3 Litre per Sqm on entire surface of roof [c] Further apply tack coat of hot blown bitumen 85/25 @ 1.2 Kg per Sqm comforming to IS : 702-1998 on entire surface of roof [d] Applying APP modified polymeric waterproofing membrane 3mm thick weight not less than 3 Kg per Sqm over entire area with overlaps 100 mm each side and joints sealed with flame torch complete all as specified & directed. [e] Further applying tack coat of hot blown bitumen 85/25 @ 1.2 Kg per Sqm over membrane surface and further spread coarse sand over bitumen @ 0.75 Kg per Sqm complete all as specified & directed. [f] Topping with 40 mm thick brick tiles laid over 20 mm thick screed bed or bedding layer in cement sand mortar in 1:4 and joints of tile shall be filled up with Cement mortar 1:3 complete.

Material & Labour for providing wate proofing treatment over cleaned roof surface with APP modified bitumen membrane 3 mm thick weight 3Kg per Sqm comprising of following and testing complete. [a] 10 mm thick rendering or screed in cement sand mortar in 1:4 mixed with water proofing compound @ 3% by weight of cement and surface finished even & fair. [b] Applying bitumen primer comforming to IS : 3384-1965 @ 0.3 Litre per Sqm on entire surface of roof [c] Further apply tack coat of hot blown bitumen 85/25 @ 1.2 Kg per Sqm comforming to IS : 702-1998 on entire surface of roof [d] Applying APP modified polymeric waterproofing membrane 3mm thick weight not less than 3 Kg per Sqm over entire area with overlaps 100 mm each side and joints sealed with flame torch complete all as specified & directed. [e] Further applying tack coat of hot blown bitumen 85/25 @ 1.2 Kg per Sqm over membrane surface and further spread coarse sand over bitumen @ 0.75 Kg per Sqm complete all as specified & directed. [f] Topping with 250x250 mm or 300 x300 mm 25 mm thick PCC tiles laid over 15 mm thick screed bed or bedding layer in cement sand mortar in 1:4 jointed & pointed in cement mortar 1:4 mixed with linseed oil @ 5% by weight of cement complete.

Supply Only Integeral water proofing compound ISI marked.

Material & Labour for preperation of new wood or wooden based surface with sand or emery paper of any description over 10 CM width or girth applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified & directed.

Material & Labour for preparation the base of new plastered surface of walls by applying 1 mm thick Birla or JK wall care putty to wall surface and rubbing with sand or emery paper of required size to achive smooth surfacre of wall and than apply two coats of oil bound distemper [Acrylic] on wall surfaces of approved colour complete all as specified & directed.

Material & Labour for preparation of new plastered surface of walls with sand or emery paper and apply two coats of cement base paint over one coat of cement primer complete all as specified & directed.

Taking down carefully point wiring of any type and any description / caping or concealed [light point, fan point or socket point] including removal of battens, pipes, plug sockets, switches, shades, ceiling roses, light fittings etc complete and making good disturbed surface to match the exisitng complete all as specified & directed.

Material & Labour for concealed Point wiring with PVC Insulated 1.5 Sqmm multi-stranded copper conductor FRLS cable 1100 Volts grade drawn into and including concealed PVC conduit medium grade not less than 20mm dia (ISI marked) including all fitting and fixings accessories including 1.25 mm thick factory fabricated sunken pressed steel terminal boxes duly painted with one coat of anti-corrosive paint outside and two coats of aluminium paint inside with and including 2.8 mm thick top cover hylam brand plastic laminated white sheet cover for mounting switches, sockets, fan regulators fixed with steel screws with cup wahsers and including PVC Insulated 1.5 Sqmm multi-strand copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed for following poit wirings:---

(a) One light / fan point controlled by one switch

(b) One socket point 3 pin switch socket out let 5 Amp controlled by one switch on same board.

(c) One socket point 3 pin switch socket out let 5 Amp controlled by one switch on Independent board.

Description same all as per item No. 82 here in above but with 1100 Volts grade copper stranded conductor FRLS cable of size 4.0 Sqmm with 2.5 Sqmm multi-strand copper conductor cable as earth wire for 3 pin switch socket outlet 15 Amp Independent board complete all as specified & directed.

Supply & Fixing switch piano flush type single pole one way 5 Amps flush type complete all as spicified & directed.

Supply & Fixing socket out let 3 pin 5 Amps complete all as spicified & directed.

Supply & Fixing Switch socket combination 2 in 1, 3 pin / 5 Amp and 15 Amps flush type of polycabonate body complete all as specified & directed.

Supply & Fixing Ceiling rose surface bakelite type 60x30 mm three terminals of polycarbonate body complete all as specified & directed.

Supply & Fixing lamp holder insulated body with back plate suitable for batten fittings complete all as specified & directed.

Supply & Fixing electronic fan regulator flush type suitable for ceiling fan complete all as specified & directed.

Material & Labour for Sub main wiring with two single core PVC Insulated cable two run of size 4 Sqmm multi-stranded copper conductor FRLS cables drawing into and including PVC conduit, medium grade not less than 25 mm dia with all conduit accessories and one run of 2.5 Sqmm multi-strand copper conductor FRLS cable as continuous earth wire complete all as specified & directed. Note : - Two run of 4 Sqmm & one run of 2.5 Sqmm cable shall be measured as one unit run.

Supply & Fixing 1x18 watt cool white four feet long decorative box type [Ultra slim] linear LED [6000K] batten retrofit light fittings with extruded aluminium body heat shrink, envoirement friendly, energy efficient prewired and making necessary electric connection from ceiling rose with 23/.0076 flexible three core copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed by Engineer-in-Charge. Make : Endura Linear NEO 20 Watt of Havells or equivalent make in Philips / Crompton or Bajaj Cat Part No. BLRB 18 W CW as approved by GE.

Supply & Fixing 1x15 watt retrofit LED light ball lamp fiitings, fitted B-22 holder of polycarbonate body and making necessary electric connection with 23/.0076 flexible copper wire 1.0 RM long & fixed to wall firmly complete all as specified & directed.

Fixing only old serviceable tube light fitings of any type including making necessary electrical connection from ceiling rose with new 0.5 RM copper wire and making good complete all as specified & directed.

Supply & Fixing Building security / street LED light fitting 35 watt IP-65 protection making electrical connection with 2.5 Sqmm twin core copper wire 1.5 long complete fixed with 40 mm dia MS pipe medium grade bracket [1.2 m long & bent to required shape] and fixed with flat iron 40x6 mm clamp two nos with nut bolts & washers as required fixed to pole or walls complete all as specified & directed. Make : Philips / Havells / Bajaj or Crompton as approved by GE.

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 4 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.

Supply & Fixing in repair RCBO double door 63 Amp, 100 mA 230 Volt complete of make L&T Cat PArt No. BC204010 or Equivalent make of ABB / Legrand complete all as specified & directed.

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], triple pole and neutral, 415 volts, 4 way with 200 Amp rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.

Supply & Fixing in repair MCB TPN four pole 415 Volt, 63 Amps,16KA breaking capacity complete all as specified & directed.

Supply & Fixing MCB Single Pole 240Volt, 6 to 32Amps,10KA breaking capacity "B" curve ISI marked complete all as specified & directed.

Supply & Fixing MCB Single Pole and Neutral 240Volt, 32 Amps,10KA breaking capacity "B" curve ISI marked complete all as specified & directed.

Supply & Fixing 300 mm sweep exhaust fan with louvers high speed copper wound motor suitable for 230 volt AC supply heavy duty complete with steel body and making necessary electric connection with ceiling rose with copper wire of suitable size complete all as specified & directed.

Supply, laying, fixing or passing through pipe commissioning & testing of XLPE PVC insulated, steel strip or wire armoured heavy duty, electric power cable with stranded aluminium conductor 1100 Volts grade cross section area 25 Sqmm 4 core complete all as specified & directed.

Supply, laying, fixing or passing through pipe commissioning & testing of XLPE PVC insulated, steel strip or wire armoured heavy duty, electric power cable with stranded aluminium conductor 1100 Volts grade cross section area 10 Sqmm 2 core complete all as specified & directed.

Material & labour for Local sand cushioning with dry and clean washed sand over and under the under ground cable in trenches, ducts for cable protection 150 mm below & 80 mm above the cable as protection of cable complete as specified & directed. Note : Punned thickness of sand shall be measured & paid.

Material & labour for Best quality locally available, sub class B bricks (Old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of the cable complete all as specified and as directed by Engineer-in-charge.

Material & labour for drilling bore hole under road / PCC / Hard standing by trenchless technology without disturbing ground for depth upto 1 m below normal GL, and dia up to 80 mm bore complete all as specified & as directed by Engineer-in-charge.

Supply & laying 50 mm bore galvanized steel tubing "light grade" with clamp using flat iron 25x3 mm welded to pipe in trenches / under roads / along pole / wall for protection of cable complete all as specified & directed.

Material & Labour for earthing complete with galvanised steel earth plate electrode of size 600mm x 600mm x 6mm thick burried directly in ground (Earth pit not less than 2.25 m deep below the normal ground level with top edge of earth plate not less than 1.5 m below normal ground level) connected to galvanised earth wire 4 mm dia as earth wire or earthing lead by means of bolts, nuts, check nuts and washers of GI or steel complete as shown in Electrical Plate No. 3 of SSR-2009 (Part-I) including charcoal dust, common salt, 20mm bore GI medium grade watering pipe, MS Sheet funnel with wire mesh, including 15mm dia GI pipe light grade for protection of GI earth wire including PCC pit 1:2:4 type B-1 using 20mm crushed stone aggregate with angle iron 40X40X5mm frame 60mm thick RCC cover with 8mm dai # TMT bars @ 100 mm centre to centre both ways i.e. horizontal and vertical complete all as directed by Engineer-in-charge and testing for required value complete. Note :- If earth resistance of earthing is not found satisfactory it will be redone by the contractor without any extra cost to Govt.

M/s Deeksha construction