C/O Permanent building for Jawahar Navodaya Vidyalaya at Reckong Peo in Distt. Kinnaur (HP) (SH- C/O 8 Nos. Type-II Qtrs and Dining block including WS and SI

Amount

Cutting in earth work in all heights and depths and in all kinds of soils including saturated soil comprising of Pick, Jumper , blasting work both in soft and hard rock with chiseling, wedging-out of rock where blasting is prohibited, their intermediate classification of soil, setting-out true to the required lines, grades, side slopes, trimming bottoms to levels as shown on the drawing and as directed by the Engineer-in-charge at site according to HP.PWD, specification of 1990 Vol-I and sorting-out useful/ un –useful materials and stacking the same in all leads and lifts in acquired width of the road and transportation of useful/ un-useful materials for filling in road ways camber, embankments for grades, improvement and leveling to required grade and disposing of all surplus excavated earth in acquired width of the road or on approved dumping sites (To be arranged by the contractor) including payment of MC/ local body dumping charges it lived any through all modes of transportion including head load or animal transport or mechanically means alongwith its leveling, fine dressing and all labour, machineries, tools, equipments and safety measures and other incidental, necessary to complete the work by mechanised means and labour if required. All useful materials such as stones , shingles, aggregates and slates shall be sorted- out and stacked along road side, the quantity of which shall not be less then 77.36 cum., failing which recovery @ Rupees 300/cum. (Three hundred per cubic metre) shall be effected from the bill of the contractor. Any loss of the public/ private property during the course of execution shall be absolute responsibility of the contractor which shall to be duly compensated by him in all respect, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Excavation in earth work in all hights and depths in all kinds of soil, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling wedging out of rock (where blasting is prohibited) and thrie intermediate classification of soil including, dewatering where ewquired, setting out to required lines, levels as shown on the drawing and directed by the Engineer-in-Charge at site and according to the HPPWD specification of 1990 ( one thousand nine hundred ninty) volume-1 (one) and sorting out useful and un-useful material and transportation of the un-usefull material for disposing at dumping site (to be arranged by contractor) including payment of precribed charges of dumping to be born by the contractor as per satisfaction of Engineer-in-Charge through all modes of transporation including head load, animal load or mechanical means along with its leveling, fire dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to completethe work by mechanical means and labour ( if required) . All usefull material such as stones, shingles aggregate and slates shall be property stacked at site and handed over to the deprtment free of cost to the maximum possible extent in all leads and lifts through all modes of transporation and used/ removed as per the direction of Engineer-in-Charge. Servicable stone to be handed over to the department free of cost. Any loss to the public and private property during the course of execution and disposal of servicable and unservicable material shall be the adsolute responsibility of the contractor and shall have to be duly compensated by him in all respect including all incident.

Excavation in drain and channel in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) (To be arranged by the contractor) including payment of MC/ local body dumping charges it lived any as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges

Excavation in foundation and trenches in earth work in all heights and depths in all kinds of soils, including saturated soils comprising of pick work, jumper work and blasting work both in soft and hard rock with chiseling and wedging out of rock (where blasting is prohibited) and their intermediate classification of soils including, dewatering wherever required, setting out to required lines, levels as shown on the drawing and directed by the engineer-in-charge at site., according to the HP.PWD. specification of 1990 (one thousand nine hundred ninety) volume-I (one) and sorting out useful and unuseful material and transportation of the unuseful material for disposing at dumping site (To be arranged by the contractor) (To be arranged by the contractor) including payment of MC/ local body dumping charges it lived any as per satisfaction of Engineer-in-charge through all modes of transportation including head load, animal load or mechanical means along with its leveling fine dressing and with all kinds of labour, machineries, tools equipments and safety measures and incidentals necessary to complete the work by mechanical means and labour (if required). All useful material such as stones, shingles aggregate and slates shall be properly stacked at site to the maximum possible extent in all leads and lifts through all modes of transportation and used/ removed as per the direction of Engineer-in-charge. Any loss to the public and private propriety during the course of execution and disposal of serviceable and unserviceable materials shall be absolute responsibility of the contractor and shall have to be duly compensated by him in all respects including all incidental charges

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30X30mmx5mm.(Thirty into thirty into five millimeter) so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden/ steel battens and ballies, height of propping and centring below supporting floor to ceiling any floor/height and removal of the same for in situ-reinforced concrete and plain concrete work, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundation, footings bases of columns etc. and mass concrete.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto any thickness in Super-structure for all floor level in all heights.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pilasters buttresses, plinth and string courses and the like.

Columns, pillars, posts and struts. Square, rectangular or polygonal in plan, in Super-structure for all floor level in all heights.

Stair cases with sloping or stepped soffits excluding landings in Super-structure for all floor level in all heights.

Beams, cantilevers, girders and lintels sides and soffits of beams, beam hunchings, cantilevers, bressumers and lintels up to any depth in Super-structure for all floor level in all heights.

Edges of slabs and breaks in floors and walls up to any width in Super-structure for all floor level in all heights.

Providing and laying cement concrete 1:8:16 (One cement: eight sand:sixteen graded stone aggregate 20mm (Twenty millimeter) nominal size) and curing complete on slab and floor excluding the cost of form work screed laid under flooring, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:6:12 (One cement : six sand : twelve graded/crushed stone aggregate 40 mm (Forty millimeter) nominal size) mechanically mix by concrete mixer including curing complete excluding cost of centering and shuttering in foundation and plinth, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cemetn concrete 1:4:8 (One cement : four sand : eight graded stone aggregate 40mm (Forty millimeter) nominal size) and curing complete excluding cost of form work in foundation and plinth, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight graded crushed stone aggregate 40mm (Forty millimeter) nominal size) light weight admixed with 200ml (Two hundred milliliter) of pidiproof LW @ 200ml (Two hundred milliletre) per 50 Kg (Fifty kilogram) of bag of cement mechanically mixed and vibrated including curing excluding cost of centring and shuttering in foudnation and plinth, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:3:6 (One cement : three sand : six graded stone aggregate 20 mm (Twenty millimeter) nominal size) and curing complete excluding cost of form work walls including attached buttresses, pilasters and their caps and bases string courses etc. upto floor all level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying cement concrete work 1:2:4 (One cement : two sand : four graded stone aggregate 20 mm (Twenty millimeter) nominal size) mechanically mixed and vibrated for compacting concrete and curing complete to give smooth and even surface including centering and shuttering etc but excluding cost of reinforced work including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

String courses, copings, bed plates, anchor blocks, plain windows sills and the like

Mouldings as in cornics window sills etc. in all thickness and girth

Providing and laying reinforced cement concrete 1:1.5:3 (One cement : one point five sand : three crushed stone aggregate 20mm. (Twenty millimeter) nominal size) mechanically mix by concrete mixer and compacting the concrete with vibrator and curing complete excluding cost of form work and reinforcement for R.C.C. work, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Foundation footings bases of columns, vertical surfaces and the like and mass concrete.

Wall any thickness

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers in Super-structure for all floors in all heights.

Column, pillars, posts and struts in Super-structure for all floors in all heights.

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing in Super-structure for all floors in all heights.

Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs. (Two point seventy five Kilogramme) of cement per square metre of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing in RCC work smooth finishing of exposed surfaces with cement morter 1:3 (One cement : three sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement water proofing treatment with Dr. FIXIT-FAST FLEX or equivalent with two component polymer modified comentitious coating consisting of comentitious powder and a polimer liquid in two coats for 1st coat :- clean and satutae surface and then applying a coat of Dr. FIXIT and the same process shall be extended upto 300mm (Three hundred millimeter) vertically the second coat shall be applied in opposite direction after four to six hours of application of first coat than sprinkle san on top surface of applied Dr. FIXIT then apply cement mortar 1:4 (One cement : four sand) and admixed with 200ml (Two hundred milliliter) of pidiproof LW @ 200ml (Two hundred milliliter) per 50Kg (Fifty Kilogram) bag complete as per Architect drawing, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing Tor steel reinforcement including cost of binding wire for R.C.C. work including cutting, bending, binding and placing in position complete in Super-structure for all floor level in all heights, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying 20cm (Twenty centimeter) thick composit stone masonry with stone facing of chisel dressed stone one line of rassal in cement mortar 1:6 (One cement : six sand) and concretebacking with cement concrete 1:3:6 (One cement: three sand: six graded stone aggregate 20 mm (Twenty millimeter) nominal size) on inner face of walls including centring,shuttering and propping complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (One cement : six sand : twelve crushed stone aggregate 20mm (Twenty millimeter) nominal size) at plinth level in Cement Mortar 1:6 (One cement: six sand) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying precast concrete solid block masonry (including quoin block ,jamb block , closes etc) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement: three sand: six crushed/graded stone aggregate 40mm (forty millimeters) nominal size in super-structure for all floors in all heights in cement mortar 1:6 (one Cement : six Sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Precast concrete block masonry in partition walls 10 cm. (Ten centimeter) thick with solid block of approved size including quoin blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (One cement: three sand: six crushed stone aggregate 40mm (Forty millimeter) and down gauge) in Super-structure for all floor in all heights in Cement Mortar 1:3 (One cement : three sand) including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone filling/ Soling under floor dry hand packed with hard stone of approved quality consolidated properly with hand or mechanical rammer to required level as per HPPWD specification 1990 (One thousand Nine hundred Ninety) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing weep holes in brick masonry /stone masonry/plain reinforced concrete abutments, wing wall, return wall,with 100mm (One hundred millimeter) dia PVC pipe extending through the full width of the structures with slope of i(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614,709,1204.3.7, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Stone filling behind retaining walls, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 19mm (Ninteen milimetre) thick commercial board water proof (ISI mark) shutter for cup boards including fixing with nickle plated piano hinges with screws etc. complete as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 40 mm thick panelled door shutters in 1st class deodar wood frame and panel of 12mm thick prepaminated board both side BWP phenol bonded exterior/ interior grade including bright finished/ black enamelled iron butt hinges with necessary screws including carriage of material , labour, tool and through all mode of transporation with in al leads and lift.

Providing and fixing 100mm (One hundred millimeter) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 50mm (Fifty millimeter) bright finished brass Cup board or ward robe Knob, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 90mm (Ninety millimeter) bright finished brass heaps and stapples (safety type) with necessary screws etc complete. including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing Magnetic catcher M-15 for cup boards, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 35mm (Thirty five millimeter) factory made flush door shutter non-decorative phenol bonded termite resistant and water proof core board with frame of ISI class hard wood and well match commercial three ply veneer with vertical grain or cross band and face veneer on both face of door shutter IS No. 2202 (Two thousand two hundred two) of kit ply/Alpro comtax as per Arch drawing as per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 75 mm x 60mm (Seventy five millimeter into sixty millimeter) rounded hand rails in straight length complete in 2nd class deodar wood, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85G with wire of dia 0.56mm (Zero point fifty six millimeter) for doors, windows and clerestory windows including first class deodar wood ornamental beading 20 mm × 12.5 mm (Twenty millimeter into twelve point five millimeter) section including bright finished black enamelled iron butt hinges with necessary screws 40 mm (Forty millimetre) thick 1st class deodar wood as per Arch. drg. including carriage of all labour equipment & materials to various location through all leads & lifts complete as per entire satisfaction of the Engineer-in-Charge.

Providing and fixing Mild Steel plain grills of required patterns in wood/steel frames of windows etc.with Mild steel flats, square or round brass with round headed bolts and nuts or by screw in all floors level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing PGI Sheet 0.63mm (Zero point sixty three millimeter) thick lining (over SDB/Toilet Door with approved adhesive screw or nails etc completeas per HPPWD specification 1990 (one thousand Nine hundred Ninety ) volume-I including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 12mm (Twelve millimeter) thick 150mm (One hundred fifty millimeter) wide pelmet with 25 mm (Twenty five millimeter) diametre wooden curtain rods and brackets including fixing 25x3mm (Twenty five into three millimeter) Mild Steel flat at 10 cm (Ten centimeter) Long and plugs etc. complete. 1st class deodar wood, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing Mild Steel sliding door bolt with nuts and screws etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

250 x 16 mm (Two hundred fifty into sixteen millimeter)

Providing and fixing Mild Steel tower bolts with necessary screws etc complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

200x 10 mm (Two hundred into ten millimeter)

150 x 10mm (One hundred fifty into ten millimeter)

Providing and fixing Mild Steel handles with necessary screws etc., including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

125 mm (One hundred twenty five millimeter)

Providing and fixing oxidized Mild Steel double acting spring hinges with necessary screws. 150 mm (One hundred fifty millimeter), including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing oxidized Mild Steel single acting spring hinges with necessary screws. 150 mm (One hundred fifty millimeter), including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing oxidized mild steel hooks and eyes. 150mm (One hundred fifty millimeter) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Vibro Hydraulically compressed and polished terrazzo tiles 330×300×25mm (Three hundred thirty into three hundred into twenty five millimter) ISI Marked No IS;1237 of NTC or its equivalent as per approved shade in 70% white cement & 30% grey cement. The ratio of chips shall be 55% white and 15% each, green, yellow and mahroon. The size of chips shall be (1B & 2B) laid in floors, treads of steps and landing on a bed of 25mm (Twenty five millimter) avrage thickness of cement mortar 1:6 (One cement : six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete(Silver grey/ Medium) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying precast terrazzo checkered tiles with semi round nosing hydraulic compressed 20mm (Twenty millimeter) thick with marble chips of specified sized laid in floor / treads of steps not exceeding 30cm (Thirty centimeter) in width and landings on a bed of 25mm (Twenty five millimeter) average thickness of cement mortar 1:6 (One cement : six sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete with tiles of Medium shades, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Vibro Hydraulically compressed and polished terrazzo tiles 330×300×25mm (Three hundred thirty into three hundred into twenty five millimter) ISI Marked No IS;1237 of NTC or its equivalent as per approved shade in 70% white cement & 30% grey cement. The ratio of chips shall be 55% white and 15% each, green, yellow and mahroon. The size of chips shall be (1B & 2B) laid in skirting and riser of steps in all height on 10mm (Ten millimter) thick cement mortar 1:3 (One cement : three sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polishing complete (Silver grey/ Medium) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying white / coloured glazed tiles 6 mm ( six millimetre) thick in skirting risers of steps and dado of approved make and size 30x45 cm (size thirty centimetre into forty five centimeter) over base of 12mm thick cement mortar 1:3 (one cement : three sand) and jointing with neat cement slurry complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 40mm (Forty millimeter) cement concrete flooring 1:2:4 (One cement: two sand: four graded stone aggregate 20mm (Twenty milimetre) nominal size) laid in one layer finished with a floating coat of neat cement as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying Cement plaster skirting up to height with cement mortar 1 :3 ( one cement : three sand ) finished with a floating coat of neat cement including rounding of junction with floor:- 15mm. (Fifteen millimeter) thick in all floor level, including curing and carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing glass strips in joints of terrazzo floors. 40mm (Forty millimeter) wide and 4mm (Four millimeter) thick, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and fixing Garsa stone/ Unistone 12mm (Twelve millimeter ) cladding on R.C.C. surface side as on faces of Arch masonry walls etc.on 12mm (Twelve millimeter) thick cement plaster 1:3 (One cement: three sand) and jointed with cement slurry including scaffolding etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and laying Non slipary anti skid ceramic tiles 5.5 mm (five point five millimeter) thick of kajaria or its equivalent in flooring (300x300xmillimeter size), tread of steps, flooring laid on a bed of 12 mm thick cement mortar 1:3 (1 sand: 3 sand) finished with flush pointing in white cement complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying 20mm (Twenty millimeter) thick baroda green marble work Table rubbed and polished in flooring/ work top/ lining over 20mm (Twenty millimeter) thick base in cement mortar 1:3 (One cement : three sand) including jointing with Cement mortar 1:2 with an admixture of pigment to match the shade complete, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and laying heavy duty precast cement concrete interlocking pavor block vibro compacted up to m 50 (Fifty) grade incluiding border or curve block gray or coloured over sub base of concrete with 25mm (Twenty five millimeter) thick average thickness of cement mortar 1:4 (One cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of block incluiding curing rubbing and polishing complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

40mm (Forty millimeter) thick.

60mm (Sixty millimeter) thick.

Extra for Making/moulding/ half round nosing to kota stone/granite/marble stone etc. including carriage of material through all modes of transportation with in all leads and lifts and as per HP.PWD. specifications of 1990 volume-I and as per direction of Engineer-in-charge.

Providing and laying marble work (table rubbed and polished) in flooring 20mm (Twenty millimeter) thick base in cement mortar 1:3 (One cement : three sand) including jointing with cement mortar 1:2 (One white cement: two marble dust)with an admixure of pigment to match the shade of the marble. 20mm (Twenty millimeter) thick Pink makrana marble, including carriage of materials through all modes of transportation with in all leads and lifts, as per HPPWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing 0.60 mm (Zero point sixty millimeter) thick prepainted steel sheet of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm (Six millimeter) diametre with prepainted limpet and rubber washers complete with all accessories, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing ridges or hips 60cm (Sixty centimeter) over all with 0.45 mm (Zero forty five millimeter) thick prepainted steel sheets of TATA DURASHINE in roofing with hot dipped metallic zinc coated sheets with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating+ back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia (Six millimeter diameter) & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing valley 90 cm (Ninety centimeter) over all 0.45 mm (Zero point forty five millimeter) thick prepainted steel sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia (Six millimeter diameter) with prepainted G.I. limpet and bitumen whashers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing 30 cm. wide 120cm overall box type prepainted steel sheet 0.45mm (zero point forty five millimeter) thick of TATA DURASHINE sheet gutter with and nuts and washers etc. including making necessary conections with rain water pipe complete as per design.complete with all accessories including carriage of material within all leads and lifts through all modes of transportation and as per HP.PWD. Specification of 1990 volume-I and as per direction of Engineer-in-Charge

Providing and fixing flushing 38 cm (Thirty eight centimeter) over all with 0.45 mm (Zero point forty five millimeter) thick prepainted sheet of TATA DURASHINE in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating+ back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia (Six millimeter diameter) & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.

Providing and fixing 150mm (One hundred fifty milimetres) dia on wall face P.V.C Rain water pipes of working pressure not less than 4.5 kg/sqm (Four point five kilogram/ square meter) including filing the joints wirth approved adhesive complete, as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge. .

Providing and fixing 150 mm dia (One hundred fifty millimeter diameter) pipe Mild Steel clamps of flat 25x3mm (twenrt fine into three millimeter) to C.I. pipes or PVC pipes with steel screws and ranef plugs etc. complete. as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

110 mm ( One hundred ten millimeter) dia.

Providing and fixing on wall faces PVC accessoreis for rain water pipes including filling the joints with approved adhesive complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

PVC Plain bend/door bend 150 mm dia (One hundred fifty millimeter diameter)

PVC Shoe150 mm dia (One hundred fifty millimeter diameter)

Providing and fixing M.S. BP sheet 2 mm (Two millimeter) thick in eaves board/ facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separately) including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing steel work of B.I.S. specification (TATA, SAIL or RASHTRIYA ISPAT) welded in built up section/ including hollow section trusses & framed work, including cutting,hoisting & fixing in position including applying a priming coat of red lead paint and the like and as per HP. PWD. Specifications of 1990 vplume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

In beams joists channels, angles, tee, flats with connecting plates or angle cleats as in main and cross beams, hip and jack rafters, purlins connected to common rafters and the like.

In gratings framed guard bars, laddres, railing, brackets and similar works.

In trusses and trussed purlins in buildings.

Providing and fixing angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X6 mm (Forty into forty into six millimeter) thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X25 mm (Fifty into twenty five millimeter) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (Two point five millimeter) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surfaceincluding carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing angle iron cupboard frames manufactured from M.S.Angle iron section 25×25×5mm (Twenty five millimeter into twenty five into five millimeter) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25×25 mm (twenty five into twenty five millimeter) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point five millimeter) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface as directed by Engineer-in- Charge.

Providing and fixing M.S. round holding down or anchor bolt with nuts and washer plates complete, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing double rebate door frame manufactured from ISLC 125mm (One hundred twenty five millimeter) (with Mild Steel Flat 125 ×4mm (One hundred twenty five into four millimeter) for centre frame) & Mild steel hollow section for rebate 40×20mm (Forty into twenty millimeter) and 2mm (Two millimter) thick welded together for making rebate including mild steel Flat Holdfast 30cm (Thirty centimeter) long and 4mm (Four millimeter) thick embedded in Cement concrete Block 1:3:6 as per design and drawing including jambs, lock jamb, beed and if required angle threshold of mild steel angle 50×25mm (Fifty into twenty five millimeter) welded or rigidly fixed by mechanical means lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point five millimeter) thick with provision for locking primer after pre-treatment of the surface complete.

Side/end mullion

Center mullion/frame

Providing and fixing steel window made of frame with mild steel channel 75×40mm (Seventy five into forty millimeter) and mild steel flat of 75×5mm (Seventy five into five millimeter) to make one frame providing double rebate with making square steel section with mild steel flat of 20×4mm (Twenty into four millimeter) and 12×4mm (Twelve into four millimeter) shuters of Z section including glass panes of 4mm (Four millimeter) thick in glazed panel and wire gauge of designation 85 (Eighty five) G with wire of 0.56mm (Zero point fifty six millimeter) diameter in wire gauge panel and fixed glazing fixed with angle and T section of 25×25×3mm (Twenty five into twenty five into three millimeter) and mild steel flat of 12×4mm (Twelve into four millimeter) in sash bars duly welded of all corners and joints properly hold fast of mild steel flat 200×50×5mm (Two hundred into fifty into five millimeter) duly welded of corner and joints of all steel section embeded in cement concrete Block 1:3:6 (One cement: three sand: six graded stone)100×100×100mm (One hundred into one hundred into one hundred millimeter) stone aggregate 20mm (Twenty millimeter) nominal size including providing and fixing of fittings that is handles tower bolts hooks and eyes and applying a coat of primer with red lead paint and fixing in position complete as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20mm × 10mm ×2mm (Twenty millimeter into ten millimeter into two millimeter) and braced with flat iron diagonals 20mm×5mm (Twenty millimeter into five millimeter) size with top and bottom rails of T. iron 40mm×40mm×6mm (Forty millimeter into forty millimeter into six millimeter) with 38mm (Thirty eight millimeter) diameter steel pulley complete with bolts and nuts locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Painting two costs (excluding priming cost on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foregin matters with Ready mixed paint other than white/ white, including carriage of materials, labour, tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter sand paper and knotting complete with Readymixed paint brushing wood primer pink as per HP. PWD. Specifications of 1990 Volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Painting two coats (excluding primimg coat) on previously painted wood and wood based surfaces with enamel paint to give an even shade including cleaning of all dirt, dust and other foreign matter sand papering and stopping with white enamel paint/ other than white, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

6mm (Six millimeter) Cement Plaster to ceiling. In cement mortar 1:3 (One cement : three sand) upto floor all level including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster in single coat on the rough side of brick/concrete walls for internal plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm (Eighty millimeter) in girth and finished even and smooth. Cement mortar 1:6 (One cement : six sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster in single coat on fair side of brick/concrete walls for internal plastering upto floor all level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80 mm (Eighty millimeter) in girth and finished even and smooth. Cement mortar 1:6 (One cement : six sand) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15 mm (Fifteen millimeter) cement plaster as pattern as shown in Architectural Drawing in single coat on fair side of brick/stone/concrete block wall for exterior plastering upto all height including arrises including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Applying white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand pepered smooth to give final matter finish to the surface complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Pointing on square rubble,coursed or un-coursed stone masonry with cement mortar 1:4 (One cement : four sand) Ruled pointing, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Distempering (Two coats) with Ist quality oil bound washable distemper of Asian paints or equivlant of approved shade and manufacture undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on un coated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Distempering (Two coats) with Ist quality oil bound washable distemper of Asian paints or equivlant of approved shade and manufacture and of required shade on undecorated ceiling/slopping surfaces to give an even shade over and including a priming coat of whiting after thoroughly brushing the surface even and sand papered smooth, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing plinth protection 50 mm (Fifty millimetre) thick in cement concrete 1:3:6 (One cement isto three sand isto six graded crushed stone aggregate 20mm (Twenty millimetre) nominal size including finishing the top surfaces of concrete smooth as per HP. PWD. Specifications of 1990 Volume-I, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing under layer for plinth protection of 75 mm (Seventy five millimeter) thick (unconsolidated) bed dry brick/stone aggregated 40 mm (Forty millimeter) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Constructing course rubble hammer dressed Ú’shaped drain with the side wall 15×22 cm (Fifteen into twenty two centimeter) in cement mortar 1:6 (One cement: six sand) and inside plastering with cement plaster 1:3 (One cement: three sand) including earthwork and laying 10cm (Ten centimeter) cement concrete in 1:5:10 (One cement: five sand: ten graded staone aggregate of 40mm (Forty millimeter) nominal size) and 7.5cm (Seven point five centimeter) cement concrete 1:2:4 (One cement : two sand: four graded stone aggregate 20mm (Twenty millimeter) nominal size) and finished with a floating coat of neat cement complete as per standard design, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge

Providing and laying in trenches galvanised mild steel tubes (medium grade), tube fittings (earh work in trenches to be measured and paid separately) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

20 mm (Twenty millimeter) nominal bore

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore

20mm (Twenty millimeter) nominal bore

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm (Twenty millimeter) to 40 mm (Forty millimeter) nominal bore by providing and fixing tee including cutting and threading the pipes complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Fixing water meter stop-cock in galvanised mild steel tube including necessary fittings such as mild steel galvanised jam nut, sockets, etc. cutting and making long screws complete (water metre and stop-cock to be measured and paid for separately). 20mm (Twenty millimeter) nominal bore, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing PVC water storage tank of ISI : 12701 marked, G.I. inlet and outlet connection, 15mm (Fifteen millimeter) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

500 litres (Five hundred litres) net capacity tank

1000 litres (One thousand litres) net capacity tank

Constructing chamber 300x300x500mm (Three hundred into three hundred into five hundred millimeter) inside size for stop cock with C.I surface box 100mm x 100mm x 75mm (One hundred millimeter into one hundred millimeter into seventy five millimeter) with hinged cover fixed in cement concrete slab 1:2:4 graded stone aggregate 20mm (Twenty millimeter) nominal size) 75 mm (Seventy five millimeter) thick foundation concrete 1:5:10 and inside palstering with cement mortar 1:3 finished with a floating coat of neat cement incluiding curing complete with 115 mm ( one hundred fifteen millimeter) thick wall of brick masonry in cement mortar 1:5 ( one cement : five sand) , including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Polytheline-Aluminium-Polythelene(PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black conforming to IS-15450-2004 water supply including clamp at one metre spacing, cutting,fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall. Internal work-Exposed on wall, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

1216 (16 mm (Sixteen millimeter) O.D.Pipe)

1620 (20 mm (Twenty millimeter) O.D. pipe)

Providing and fixing composite end seal compression fittings as per IS-15450-2004 for cold water supply e.g. tees,elbows, reducers, connectors, couplers and clamps with jointing testing and fittings complete including cutting and making good the walls etc., including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge. Polytheline-Aluminium-Polythelene (PE-AL-PE) Composite end seal compression fittings.

EqualTees:- 1216mm size

1620mm. Size

b) Reducing Tee:- 1620x all branches

2025 X with all branches

Female branch Tee:- 1216x1216x15mm thread

1620x1620x20mm. thread

Female elbows:- 1216 x15mm thread

1620x15mm thread

Male thread connector:- 1216x15mm thread

1620x15mm thread

Female thread connector:- 1216x15m thread

1620x15mm thread

Couplers:- 1216mm

Reducers:- 1620x1216mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (Three millimeter) thick bolts and nuts complete including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3 mm (Three millimeter) thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC offset 45 Degree ISI marked including fixing with approved adhesive etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

110 mm x 90 mm (One hundred ten millimeter into ninety millimeter)

Providing and fixing P.V.C. Reducer ISI marked including jointing with approved adhesive etc. complete., including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150mm × 110mm (One hundred fifty millimeter into one hundred ten millimeter) diameter.

Providing and fixing P.V.C ‘P’ or ‘S’ trap for water closet (Squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Chase in stone/brick masonry walls for fixing sand cast iron/ cast/spun iron pipes and fitting including making good the same with stone/ brick work in cement mortar 1:3 (One cement : three sand) including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

150 mm dia (One hundred fifty millimeter diameter)

110 mm dia (One hundred ten millimeter diameter)

Providing and fixing vitreous China wash down,water closet squatting pan Orrissa Pattern of Hindware (Indian type W.C pan) Cat No. 20004 Having size 58x40cm (Fifty eight into forty centimeter) (Earth work, bed concrete, foot rest and trap to be measured and paid for separately) as per HP. PWD. specifications of 1990 volume-I including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in- Charge.

Providing and fixing 10.00 ltr. (Ten liters) capacity PVC low level duel flushing cistern CERA catalogue No. 2603 or equivalent with a pair of brackets with fittings such as lead valve, less syphon, 15mm (Fifteen millimeter) nominal size PVC ball valve with polythene float, PVC handle, union and coupling for connection with inlet, outlet and overflow pipes 40mm (Forty millimeter) diameter PVC flush bend with cistern and closet & over flow pipe to be paid for separately, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing G.I. inlet conection for flush pipe with G.I. Pan, including carriage of materials through all modes of transportation with in all leads and lifts, as per PWD specifications and as per direction of the Engineer-in-charge.

Providing and fixing vitreous china wash basin No. 10001 with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:- Flat back 550mm x 400 mm (Five hundred fifty millimeter into four hundred millimeter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing viterious china pedestal for wash basin complete recessed at the back for the reception of pipes and fittings, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing stainless steel laboratory sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting 470 × 420mm (Four hundred seventy into four hundred twenty millimeter) with bowl depth 178 mm (One hundred seventy eight millimeter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass waste for wash basin or sink 32 mm dia (Thirty two millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing M.I. Union for wash basin or sink 32 mm dia (Thirty two millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 600 mm x 450 mm (Six hundred millimeter into four hundred fifty millimeter) bevelled edge mirror of superior glass mounted on 6 mm (Six millimeter) thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. Brass screws and washers. 600 mm x 20 mm (Six hundred millimeter into twenty millimeter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 100mm (One hundred millimeter) diameter C.P. grating for floor or nahani/ gully/ floor trap, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing Galvanised mild steel puff pipe 1m (One meter) long with brass perforated cap with 20mm (Twenty millimeter) diameter, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. Brass bib tap (heavy duty ISI marked IS:8931 & 8934) of Jaquar with capastan head. 15 mm dia (Fifteen millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P. brass pillar tap with Capstan head (heavy duty ISI marked IS:8931 & 8934) 15 mm dia (Fifteen millimeter diameter) including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing C.P.brass angle valve (heavy duty ISI marked IS:8931 & 8934) 15 mm (Fifteen millimeter) without Nuts and pipe, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing P.V.C. connection with brass unions:- 300/450 mm (Three hundred/four hundred fifty millimeter) length (heavy duty ISI marked IS:8931 & 8934) 15 mm (Fifteen millimeter) nominal bore, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixig brass full way valve with wheel, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore

20mm (Twenty millimeter) nominal bore

Providing and fixig G.I. or M.I. union of following sizes (where not included in the item) including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

15mm (Fifteen millimeter) nominal bore

20mm (Twenty millimeter) nominal bore

Providing and fixing PVC waste pipe 32mm dia (Thirty two millimeter diameter) and 60cm (Sixty centimeter) long complete, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing 32mm (Thirty two millimeter) diameter lead waste pipe for wash basin or sink including brass check nut, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying 150mm (One hundred fifty millimeter) diameter (to level or slopes) and jointing with approved adhesive high pressure PVC spigot and socket waste and ventilating pipe in trenches, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and laying cement concrete 1:4:8 (One cement : four sand : eight graded stone aggregate 40mm (Forty millimeter) nominal size) mechanical mixed and vibrated bedding for stoneware pipes of the following internal diameters, necessary form work and curing complete. 150mm (One hundred fifty millimeter) including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing, laying, jointing and pointing with a stiff mixture of cement mortar in proportion of 1:1 (One cement : one sand) 150mm (One hundred fifty millimeter) internal diameter salt glazed stoneware grade 'A' half round channels, including carriage of materials, labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Providing and fixing precast reinfirced cement concrete man hole cover 500mmx650mm ( five hundred into six hundred fifty millimeter) size and 62.5mm ( sixty two point five millimeter) thick complete including carriage of material , labour, tool and plant through all mode of transporation within all leads and lifts ans as per direction of Engineer-in-Charge.

Constructing manhole with R.C.C. top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement : 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete. (a) Inside size 800mm x 800mm and 500mm deep including precast RCC cover 500x650mmx62.50mm complete with 200mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) complete as per HP.PWD specifications of 1990 volume-I including carriage of material, labour , tool and plant through all modes of transporation within all leads and lifts and as per direction of Engineer-in-Charge.

Constructing manhole with R.C.C. top slab in 1:2:4 mix in 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8 (1cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 (1cement : 3 sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete. (a) Inside size 800mm x 800mm and 1000mm deep including precast RCC cover 500x650mmx62.50mm complete with 200mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand) complete as per HP.PWD specifications of 1990 volume-I including carriage of material, labour , tool and plant through all modes of transporation within all leads and lifts and as per direction of Engineer-in-Charge.

Cutting holes through existing brick work including making good the same in cement mortar 1:6 (One cement: six sand) per CMs. Depth of cutting:- Holes upto and including 400 Sq. cm (Four hundred square centimeter) in area, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

Cutting holes upto 15cm × 15cm (Fifteen centimeter into fifteen centimeter) in R.C.C. beams/ floors and roofs for passing drain pipe etc. and repairing the holes after insertion of drain pipe etc. with cement concrete 1:2:4 (One cement : two sand : four graded stone aggregate 20mm (Twenty millimeter nominal size) including finishing complete so to make it leak proof, including carriage of materials ,labour ,tool and plants through all modes of transportation with in all leads and lifts, and as per direction of the Engineer-in-charge.

NORBU CHHERING